PROVN OF 01 X 2 TON ELECTRIC OVERHEAD TRAVELLING CRANE IN REPAIR BAY FOR B VEHICLES IN BLDG NO P-23 OF LT AD REGT WKSP (COMP) AT KANPUR CANTT UNDER GE (I) KANPUR

Amount

Design, supply, Install, testing & commissioning of Indoor crane electrically floor operated travelling on Single girder or as per OEM having straight travel path in X-Y (6 way) direction operating on 415 volts, 3 phase 50 hz having Capacity- 2Ton, Rectangular EOT Crane , Span-X- direction 8 mtr Y- direction 8.5 mtr LT girder for crane with sq bar ISMB-250 Travel- 8mtr Bay length Lift-6 Mtr with RSJ Type Girder, Fabricated Rolled steel Type End carriages with End Connection plates -Rubber Buffers in LT Wire Rope Hoist- Model WRH, Cap 2T, Fall-4, and Lift-6 Mtrs, with 4.5 mpm Hoisting speed; 17 mpm CT speed; 2.2 KW Hoisting Motor .18 KW X1 CT Motors , LT Drive Assly- Wheel Mounted Fixed Axle Assly with Ball Bearing Wheels of Dia 150 mmx4 Nos; 20 mpm ,lT speed; .55 Kwx2 Nos Motor , Complete Control Panel, CT Trailing Cable system, Limit switches for all motions & push button pendent suspended to hoist.The motors shall be width VVVF drive of specified make for different travel should be 6 pole 415 volt,50 hzof suitable HP/KW enclosure of IP-55 as per IS -325 suitable for frequent reversing , frequent acceleration and breaking class 'F' insulation having 40% CDF (Cyclic duration factor) and 150/Hr start/stops through floor operated pendent push button and remote control with suitable gear boxes.CPRI approved control panel of double door type with all necessary protections,switch gears and relays shall be made out of CRCA sheet having thickness of not less than 2 mm fabricated of suitable size including powder coated paint over one coat of red oxide primer having IP-65 protection and Hoist hook mounted complete including following all as directed by Engr-In-Charge.Note: Crane drawing should be submitted by contractor for approval of GE before placing the order. Technical specififcation of 2T SGEOT Crane are given below:- Make : Crane( Single Girder EOT Cranes ) (a) Safex Energy Pvt Ltd (b) Pioneer Cranes & Elevatores Pvt Ltd (c) Hercules Hoists

(a) Specifications: IS3177/807 (b) Capacity/Lift: 2 Ton/11 M (c) Span: Detail as above mentioned (d) Duty: Class II (Hoist is class IV) (e) Hoisting speed: 4.5 mpm (f) CT Speed: 17 mpm (g) L.T. Speed: 20 mpm (h) Hoisting motor - Type & Rating: Sq Cage type Rating- 2.2 KW-1 No (j) C.T. Motor, -Type & Rating- Sq cage Type, Rating- .18 KW- 1No (k) L.T. Motor , Type & Rating- Sq Cage type, Rating-.37 KW- 2 No (l) Gear Boxes- Helical gear box in hoist & CT (m) Detail of all safety limit switches- roller lever type in hoist (n) L.T Assly Type- Wheel mounted Fixed Assly (o) Details of L.T. wheels EN9

Excavating in trenches in soft/loose soil, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes and laying of cables etc. n exc 10 sqm on plan and getting out soft/loose soil complete all as specified and directed.

Returning filling, in including spreading ,leveling, watering and well ramming in layers not exc 25 cm each complete all as specified and directed

Removing excavated material to a distance not exceeding 50 meters and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed

M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable complete all as specified and directed

M&L for Sub class ‘B’ bricks old size. laid dry flat over the cable abutting each other, length of cable equal to width of brick all as required complete all as specified and directed

M&L for drilling manually in soft / loose soil under road / hard standing / culvert / nala of suitable bore for protection cable & pipe upto 80 mm bore complete all as specified. Note: Depth of bore shall not be more than 1 Mtr from original ground level complete all as specified and directed

M&L of GI tubing light grade 80mm bore with fittings laid for protection of cable under road crossing fixed to walls or pole complete all as specified and as directed.(clamps for fixing pipe, nuts, bolts washers shall be measured separately ) complete all as specified and directed

Supply and laying in trenches or fixing to wall/pole or passing through pipe in replacement of XLPE insulated heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 35 Sqmm 3.5 core.Make of cable Gloster/Havells/ Paragon/ Grandlay/. (Note : Incl making good all distributed wall surfaces/ flooring/tilling to match with existing specification). complete all as specified and directed

M&L of Earthing complete with galvanised cast iron earth plate electrode of size 600x600x6.3 mm thick as earth electrode with top edge of the earth plate not less than 1.5mtr below ground level galvanised iron strip 32x6mm Earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron/steel all as directed including providing earth wire protection pipe GI light grade15mm dia from earth plate to main switch board/panel, watering pipe 20mm dia with wire mesh and funnel at top, earth pit and RCC pit cover in PCC 1:3:6 adequate quantity of charcoal dust and salt all around the erth plate, earth work in any type of soil remaing surplus excavated material all as required at site and specified in EP No 5 of SSR part I 1991 or directed incl testing on competion.

S&F of MCCB 4 Pole 415 Volts 3 phase 100 Amps 25KA, thermal magnetic release S1 -01 No (incoming). complete all as specified and directed.

S & F in MCCB enclosure box, factory made, to house MCCB of 100 Amps with all fixing arrangement to fix on wall including provision of electric connection including suitable size of aluminium lugs complete all as specified and directed.

Demolition of Concrete in ground floors and pavings exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for PCC 1:4:8 Type D2 (40mm graded aggregate) as in foundation and mass concrete complete all as specified and directed

M&L for RCC M-25 Design mix (20mm graded aggregates) as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc and mass concrete complete all as specified and directed

M&L for RCC M-25 Design mix (20mm graded aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed

M&L for RCC M-25 Design mix (20mm graded aggregates) as in Beams, cantilevers,bressummers, lintels complete all as specified and directed

M&L formwork to sides of concrete foundation footings, bases of columns raft and raft beams sides and soffits (if any) of foundation and plinth beams and similar work : vertical or to batter Rough finished surfaces of concrete complete all as specified and directed

M&L formwork to sides of pillars, post, struts, piers, columns and stanchions for fair finished surface complete all as specified and directed

M&L formwork to sides and soffits of floor or roof beams, beam haunch?ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

S&F TMT bars 5mm dia and over upto 10mm dia bar as in stirrups cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F for diameter of neck in 16 to 20mm mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5cm and n. exc 30cm longexc long

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

M&L for preparation of new steel surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat zink chrome red oxide primer complete all as specified and directed.

M & L PCC 1:2:4 type B2 using 40 mm graded stone agg as in floor finishing, foundations,filling and mass concrete including mastic filling in joints complete all as specified and as directed

M & L rendering 10 mm thick in CM 1:4 on brick or concrete wall sufaces complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coat of white wash complete all as specified and directed.

Deep Contractor