Additional Estimate for Construction of Dr. Bhupen Hazarika Kalatirtha at Panigaon Nogaon, Assam (Phase I)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Dry brick pitching half brick thick including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand

12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on the rough side of single or half brick wall 1:4 (1 cement: 4 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately)Sal wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately):Second class teak wood.Second class teak wood 35 mm thick shutters

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coatsPAINTING ON WOOD AND WOOD WOOD BASED SURFACES

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 300x10 mm:

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.ROOF TRUSS/MS FRAMING FOR AUDITORIUMs SITTING ARRANGEMENT

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil ......., work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 ............. water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge....... 25 mm thick

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 600 mm

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer- in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coating 50 micron)

Float glass panes 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately) 25 mm thick

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. 12 mm thick.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 100mmx100mmx60mm deep

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 5/6 A switch

2 way 5/6 A switch

15/16 A switch

3 pin 5/6 A socket

6 pin15/16 A socket

TV antenna socket outlet

Bell push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

12 Module (200mmX150mm

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 3 Module

4 Module

6 Module

12 Module

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation,testing and commissioning of prewired fluorescent fitting compact fluorescent fitting of all types complete with all accesssories and tube/lamp etc. directly on ceiling/wall, including connection with 1.5sqmm FRLS PVC insulated,copper conductor, single core cable and earthing etc as required.

Installation,testing and commissioning of ceiling fan, including wiring the down rods of standard length(upto 30cm) with 1.5sqmm FRLS PVC insulated,copper conductor, single core cable and earthing including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Numbering of ceiling fan/exhaust fan/fluorescent fitting as required.

Installation of exhaust fan in the existing opening, including making good the damages,connection,testing and commissining etc. as required.Upto 450mm sweep.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Double pole

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A

Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.63 Amp TP&N

Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 Amp, 16 KA, TPMCCB

125 Amp, 16 KA, TPMCCB

250 Amp, 35 KA, TPMCCB

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm (45mm)

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm

Material cost of flotex flocked textile floor covering of nylon 6.6 face fiber or equivalent of approved make with 100% nylon and completely water proof resilient backing. The flooring should be anti-static weight of 1.8 kg/sqm of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sqm. The floor covering should have fire test EN-13501, appearance retention hexapod ISO 140-8, friction slip resistance text EN 14041 class DS, sanitized anti-microbial treatment with resilient water proof backing anti-allergic which is certified by british allergy foundation with ten year replacement guarantee

Wall paper; wall paper in diffferent shade and design with complete finishand pasting ar per direction.

Supplying & placing center table with an overall size 1200mm X 600mm X 450mm. The top shall be made up of 30mm thick Pre-laminated particle board of grade II of IS 12823. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The lower shelf shall be made up of 18mm thick Pre- laminated particle board. The under structure shall consist of SS 202 grade shiny chrome finish pipe frame having cross- section area 30mm X 15mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO- 50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.

Supplying & placing cafe table with an overall size 900mm x 900mm x 750mm. The top of the table shall be made up of 20mm thick granite rock. The top profile shall be in square shape and the edges shall be in round shape. The top shall be supported on 11mm thick ply-board having size 750mm X 750mm and SS 202 grade pipe frame having cross-section area 40mm X 20mm with 1.6mm thick in X shape. The table under structure shall be made up of SS grade 202 base pole leg having Dia. 63.5mm. The base shall be in X shape with SS pipe frame having cross-section area 40mm X 40mm. There shall be leveler shoe provided with metal insert at the base to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.

Supplying & Placing Cafe Chair. The seat shall be made of 15mm thick hot pressed plywood upholstered with high resilience polyurethane foam 19mm thick having density 40kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM and the back shall be made of metal frame upholstered with high resiliance polyurethane foam 12mm thick having density 23kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM. The seat and back shall be fixed with plywood & metal frame. The frame structure shall be supported by four legs made up of SS with shiny chrome finish square pipe of size 20mm X 20mm with 1.6mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The Seat size shall be 410±10 mm(D)X430±10 mm(W) and back size shall be 420±10 mm(W)X400±10 mm(Ht) from seat. Overall height shall be = 860±10 mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.

Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and having density 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam thick having density 32Kg/m³. SS strip shall be provided on front of the arm having length 515mm with cross-section area 14mm X 4mm. The structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have shiny chrome finish SS leg with height 100mm and 10mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. 3 Seater : The seat size shall be 500±10 mm(D) X 1480±10 mm(W), seat height = 430±10 mm, overall width = 1625±10 mm, overall depth = 750±10 mm & overall height = 700±10 mm. 2 Seater : The seat size shall be 500±10 mm(D) X 1015±10 mm(W), seat height = 430±10 mm, overall width = 1160±10 mm, overall depth = 750±10 mm & overall height = 700±10 mm. Single Seater : The seat size shall be 500±10 mm(D) X 545±10 mm(W), seat height = 430±10 mm, overall width = 690±10 mm, overall depth = 750±10 mm & overall height = 700±10 mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.

Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical indoor type floor/wall mounting compartmentalize panel board of size 0.95M(B)X 1.30M(H) X 0.40M(D) made of 16 SWG (1.66 mm) thick C.R. sheet and 40mm X 40mm X 5mm size angle having 4 nos legs at the bottom. The panel board is to be errected in 1 : 3 : 6 PCC foundation including brick soling / grouting etc. complete neatly wiring done with provision for one no 250A 4pole MCCB or Switch Fuse Unit as incomer and provision for 8nos DP or TPN out going as specified and directed by the deptt. confirming to IP 43 protection comprising of the following electrical items:1. i) 40mm X 5mm 4 strip copper Bus - Bar 1.20 M length each (Incoming & Outgoing Switch Gear of reqd. rating along with Meters will be measured and paid separately)

Supplying including laying of 3.5 core 95sqmm Aluminium XLPE UG cable (make Polycab or equivalent) with necessary connection as required and directed by the Department.

Supply, installation, testing and commissioning of wall/ceiling mounting 20W LED polycarbonate tube with inbuilt driver metal heat sink with double sided connection. Crompton or equivalent make.(LT8-20-865(2).

Supply, installation, testing and commissioning of recessed mounting 18W LED down light suitable for any modern workspace with Polycarbonate housing withsuperior light output and integral driver Efficacy 100LM/W. Crompton or equivalent make.(LCDPEP-18-WW).

Supply of 1200mm sweep,brass nickel/Antique brass/antique copper ceiling fan in the existing hook of the buildintg, (Havells make).

Supply of 300mm sweep, 900rpm(2N) heavy duty exhaust fan(Havels make,Considering 18%GST)

Supply of 450mm sweep, 2N 1400 rpm metalic heavy duty exhaust fan in the existing hole of the buildintg, Turbo force SP.(Havels make).

Supply of pedestal type fan and regulator 600mm adjustable height, Min.1400mm Max.1650m(for 600mm size fan(Bajaj supreme plus air circulator 600mm pedestal).

Supply of foot light (85 mmx 85mm), LFTLW1S003XW# Die cast Aluminium housing Polycarbonate diffuser White and grey Finish IP44.(Jaguar make).

Supply and Installation of Anutone Subtex Nubby, square edge, Glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having volume density 120Kgs/m3, weight 1.8kg/m2 which is suspended by using 0.3mm thick Anutone Skelet TrelisT15 metal grid system.For Hall Ceiling. Technical Specification • Fire (Class) – 1 & P • Acoustics – NRC 0.9 (For E900 Mounting) • Thermal conductivity (W/mk)– 0.066 • Climate (°C, RH) – 40, 95 • Light reflectance (%) – 85 • Green (VoC, RC %) – Low, 35

Supply & installation of Anutone Slats Spots MP3 Lite, made of pinewood E1 grade fiberboard, melamine finish, having 3-6 mm dia circular microperforations @ 16mm pitch, backlined with Soundtexblack acoustical fleece of 0.27mm thick, surface density 63g/m2, tongue-groove edge for a seamless look, 1-test FR grade, size 192 x2440x16mm, volume density of base board 700Kg/m3, weight of base board 12Kg/m2 installed by using Anutone Strut framework system. Hall Ceiling Spot. Technical Specification Fire (Class) – B • Acoustics – NRC 0.75( For C40 Mounting) • Climate (°C, RH) – 50, 70 • Light reflectance (%) –75 (Maple Arce) • Green (VOC, RC %) – E1, 25

Supply & installation of Anutone Slats Spots MP3 Lite, made of pinewood E1 grade fiberboard, melamine finish, having 3-6 mm dia circular microperforations @ 16mm pitch, backlined with Soundtexblack acoustical fleece of 0.27mm thick, surface density 63g/m2, tongue-groove edge for a seamless look, 1-test FR grade, size 192 x2440x16mm, volume density of base board 700Kg/m3, weight of base board 12Kg/m2 installed by using Anutone Strut framework system. Wall Panel Spot. Technical Specification • Fire (Class) – B • Acoustics – NRC 0.75( For C40 Mounting) • Climate (°C, RH) – 50, 70 • Light reflectance (%) –75 (Maple Arce) • Green (VOC, RC %) – E1, 26

Anutone Strand Slim Graphics of customed size. Supply and installation of Anutone Strand Synth Slim, polyfibre panels, core-pigmented, high-density, SynthPF rigid panels of size 1200x2400x9mm thk, volume density 220kg/m3, weight 2kg/m2 adhered on Anutone Strand1 primer, square edge Magnesite bonded pinewood fibre core tiles of size 600x1200x10mm, volume density 400kgs/m3, weight 4kg/m2 installed by using Anutone Strut framework system. Wall Panel Synthetic Slim Technical Parameters • Acoustics – NRC Upto 0.7 • Thermal (W/mk)– 0.039 • Climate (°C, RH) – 50, 99 • Light (%) – Colour Dependant • Green (VoC, RC %) – Nil, 61

Anutone Strand Slim Graphics of customed size. Supply and installation of Anutone Strand Synth Slim, polyfibre panels, core-pigmented, high-density, SynthPF rigid panels of size 1200x2400x9mm thk, volume density 220kg/m3, weight 2kg/m2 adhered on Anutone Strand1 primer, square edge Magnesite bonded pinewood fibre core tiles of size 600x1200x10mm, volume density 400kgs/m3, weight 4kg/m2 installed by using Anutone Strut framework system. Wall Panel Graphics Technical Parameters • Acoustics – NRC Upto 0.7 • Thermal (W/mk)– 0.039 • Climate (°C, RH) – 50, 99 • Light (%) – Colour Dependant • Green (VoC, RC %) – Nil, 61

Supply and Installation of Anutone Subtex Nubby, square edge, Glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having volume density 120Kgs/m3, weight 1.8kg/m2 which is suspended by using 0.3mm thick Anutone Skelet TrelisT15 metal grid system.Stage Ceiling 2X2 Technical Specification • Fire (Class) – 1 & P • Acoustics – NRC 0.9 (For E900 Mounting) • Thermal conductivity (W/mk)– 0.066 • Climate (°C, RH) – 40, 95 • Light reflectance (%) – 85 • Green (VoC, RC %) – Low, 35

Construction of Proscenium with MS pipes and finished with 12mm W/P plyboard and laminates.

Wooden Work for Designing

SITC of Polished wooden BIT

Auditorium chair. The seat and back are made of thick hot pressed plywood, upholstered with fabric and moulded polyurethane foam. The chair shall have a push back mechanism, PU arm, all metal components shall be powder coated in black color with minium 40 micron. Overall size; 860 (H) x 560 (W) x 580 (D)

Supply of 18" Passive Subwoofer, Frequency Response (-3 dB) 38 Hz - 800 Hz, Frequency Range (-10 dB) 41 Hz - 200 kHz, Rated Power 1000W Continuous, 4000W Peak, Maximum SPL 137 dB, Sensitivity 98 dB, Nominal Impedance 8 Ohms, Coverage Pattern Omni-directional, LF Driver 18" Ultra Long Excursion ADR Drivers, 4" VC - Ferrite, Inputs 2 x Speak-on Connectors, Wired Parallel.

Supply of Single 8" IP 67 rated 2-way Speaker System, Frequency Response (-3 dB) 59 Hz - 20 kHz, Frequency Range (-10 dB) 55 Hz - 20 kHz, Rated Power 125W Continuous, 500W Peak, Maximum SPL 121 dB, Sensitivity 90 db, Nominal Impedance 8 Ohms or 100/70 V, Coverage Pattern 100° x 60°, LF Driver 8" Weather Resistant Woofer, HF Driver 1" Silk Dome Compression Drivers, 1.4" VC, Transformer Taps 60W, 30W, 15W - 100 / 70 V.

Supply of 7" COAXIAL SPEAKER -IP67, Freq. Response(-3dB):80Hz-18kHz, Freq.Range(-10dB): 61Hz-20kHz, Rated Power:200W,800W Peak, HDispersion:100º(-6dB), VDispersion:100º(-6dB, Crossover Frequency:2.2kHz Passive or Bi-amplified, Nominal Impedance: LF/FR-8Ω, HF-8Ω, 100V/70V Transformer Taps:100W,50W, 25W,10W, Maximum SPL:115dB, 121dB Peak, Shielded Screw Terminals,

Supply of 7" COAXIAL SPEAKER -IP67, Freq. Response(-3dB):80Hz-18kHz, Freq.Range(-10dB): 61Hz-20kHz, Rated Power:200W,800W Peak, HDispersion:100º(-6dB), VDispersion:100º(-6dB, Crossover Frequency:2.2kHz Passive or Bi-amplified, Nominal Impedance: LF/FR-8Ω, HF-8Ω, 100V/70V Transformer Taps:100W,50W, 25W,10W, Maximum SPL:115dB, 121dB Peak, Shielded Screw Terminals,

Supply of Air Cooled Floor Mounted Packaged Air Conditioners Unit to operate from 415+- 10% volt , 50 Hz , 3 phase power supply and consisting of hermitically sealed Fixed speed scroll compressor and Compiatble of R410A as refrigerant. The indoor unit will consist of evaporator coil,evaporator fan,expansion valve/capillary, fixed speed scroll compressor and in Outdoor unit will consist of condenser fan and condenser copper coil complete in all respect. Both the indoor & outdoor unit will be connected using refrigerant piping &control cabling.Capacity-16Tr(Make-Blue Star/Daikin/Voltas)

Supply of Air Cooled ceiling suspended Ductable unitary Air Conditioners Unit to operate from 415+- 10% volt , 50 Hz , 3 phase power supply and consisting of hermitically sealed Fixed speed scroll compressor and Compiatble of R410A as refrigerant. The indoor unit will consist of evaporator coil,evaporator fan,expansion valve/capillary, etc complete in all respect.The outdoor unit will consist of compressor ,condensing coil & condensing fan etc. complete in all respect. Both the indoor & outdoor unit will be connected using refrigerant piping &control cabling. Capacity-8.5Tr(Make-Blue Star/Daikin/Voltas)

Indoor & Outdoor Installation, Testing By N2 & Commissioning .Floor Mounted Packaged Machines

Ducted Machines

Canvas Connection

Hard /Soft Drawn Copper Pipe from Indoor to Outdoor considering 10m With 9 mm Nitrile Rubber Insulation with Proper Support.Nitrile rubber insulation is not required for Packaged Machines.3/8" Dia

Hard /Soft Drawn Copper Pipe from Indoor to Outdoor considering 10m With 9 mm Nitrile Rubber Insulation with Proper Support.Nitrile rubber insulation is not required for Packaged Machines. 1/2" Dia

Hard /Soft Drawn Copper Pipe from Indoor to Outdoor considering 10m With 9 mm Nitrile Rubber Insulation with Proper Support.Nitrile rubber insulation is not required for Packaged Machines. 7/8" Dia

Hard /Soft Drawn Copper Pipe from Indoor to Outdoor considering 10m With 9 mm Nitrile Rubber Insulation with Proper Support.Nitrile rubber insulation is not required for Packaged Machines. 1-1/8" Dia

Communication Cable between Indoor & Out Door 7Core x 1.5Sqmm Cu Communication Cable

Communication Cable between Indoor & Out Door 3Core x 1.5Sqmm Cu Communication Cable

Drain Piping with 6mm Nitrile Rubber Insulation 25mm

Supply of SMART PIR Pre-Insulated ducting (Factory PreCut) made of 20mm thick SMART PIR (Polyisocynurate Rigid) Panels with 80 micron Embossed Aluminum foil(with Anti microbial, Anti Fungal, Anti corrosion, UV Protection coating) on both the sides with standard Accessories in Polymer, CFC, HCFC, VOC free,Density 45– 48 kg +/- 3 kg/m³,Thermal Conductivity 0.019 W/mK,Water Absorption0.03 % by Volume,CompressiveStrength not less than 160 kPa, Flexural Strength not less than 650 kPa, Fire propagation index - Class ’O’. 20MM THICK

Damper & Grilles Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications

Supplying, fixing, testing commissioning of supply air grill /Diffuser of powder coated aluminium with GI volume control dampers complete as required.

Supplying, fixing, testing commissioning of Return air grill/Diffuser of powder coated aluminium with out GI volume control dampers.complete as required.

Support for Ducting and Piping

MS Structure work for Outdoor Installation

Undedeck insulation with 19mm thick closed cell Nitrile rubber as per Standard

Refrigerant Gas Charging-R410AGas

Commissioing and Balancing of the System

CE Certified LED Blinder Effect Light with latest RDM technology for user friendly operation with below specifications: • Light Source : Quad LED COB Source • Power Factor : >0.95 @ 230V AC 50Hz • Color Temerature : 3200K, CRI & TLCI Value > 95 • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 4/8 DMX-512 Channel Modes • Beam Angle : 40° • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • Lux output at 2 Mtr : > 8,500 Lux @ 40° • Dimming: 0 - 100% Electronic Dimming • Power and DMX: Loop in and loop out compulsary • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS

CE Certified LED PAR Light with latest RDM technology for user friendly operation with below specifications: • Base Color RGBW Color Mixing • LED Configuration : Multiple Nos Individual RGBW LED Configuartion • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 8 DMX-512 • Beam angle: 15° • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run, Sound Active • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • LUX @ 2m: >10,500 @ 15° Beam Angle • Dimming: 0 - 100% Electronic Dimming • Function: strobe, dimming, sound active and Master slave. • Housing: Die Casted Aluminium or Metal Housing with black epoxy polyster powder coated finish. • Power and DMX: Loop in and loop out compulsary • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS

CE Certified LED Profile Spot Light with latest RDM technology for user friendly operation with below specifications: • Light Source : Single LED COB Source • Color Temerature : 3200K, CRI & TLCI Value > 95 • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 1/2/3 DMX-512 Channel Modes • Beam Angle : 19° or 15° • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • Lux output at 2 Mtr : > 20,000 Lux @ 19° or 15° • Dimming: 0 - 100% Electronic Dimming • 4 Beam shaping shutters • Accessory slot for Gobo and gobo holder, Iris & Color Frame should be available or else fixture will be rejected. • Housing: Metal Housing with black epoxy polyster powder coated finish or PVC Body with matt black finish • Power and DMX: Loop in and loop out compulsary • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS

CE Certified LED PAR Light with latest RDM technology for user friendly operation with below specifications: • Base Color 3200K Color Mixing • Color Temperature : 3200K with CRI > 90 • LED Configuration : Multiple Nos Individual 3200K LED Configuartion • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 1 DMX-512 • Beam angle: 15° • Control mode: RDM, DMX512 & Manual • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • LUX @ 2m: >7,500 @ 15° Beam Angle • Dimming: 0 - 100% Electronic Dimming • Function: strobe, dimming, sound active and Master slave. • Housing: Die Casted Aluminium or Metal Housing with black epoxy polyster powder coated finish. • Power and DMX: Loop in and loop out compulsary • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS

Die cast Aluminium C - Clamp with safety chain duly epoxy polyester powder coated in black matt texture finish and safe working load of 100kg with below specifications. • Lock - MS threaded Galvanized lock key, • Plastic Glass filled nylon moulded M6 key. • Receptacle - 28mm standard TV spigot. • Safety - MS Galvanized chain with pin. • Finish - Pretreated and black epoxy polyester powder coated. • Self-weight - 0.54Kg

Safety bond with lock clip 1.5 Mtr Long made with twisted pair of GI wire rope, 2mm or 3mm Thickness with sleeve to be fixed around the grid to avoid fall of the material in case if the "C" clamp is not locked properly. SWL 150Kgs.

79mm Round Identification name plate duly epoxy polyester powder coated in matt texture finish.

MS C track of size 50 x 40 mm size with 3mm thickness or higher size, Self-weight 3.3Kg per mtr. All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish.

Customized MS Suspenders made up of • MS fish plate 150 x 150 x 6 mm with hardware’s if required as per site condition • MS Angle 40 x 40 x 5 mm or higher size required length as per site condition to Hold the "C" track rigidly held With SWL of 200kg. (As per site requirement). • Height adjustable M12 stud of suitable length as per site requirement along with suitable hardware’s with pipe coupler clamp. (As per site requirement). • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish.

Main Valance Bar, length 12.5 Mtrs made using 40NB, 48mm OD construction arrangement 2mm Thickness undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with suitable suspenders.

Main Curtain track system 15 Mtrs long, center parting with overlap of 0.9mtr arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications: • Heavy duty curtain track duly epoxy polyester powder coated in black matt texture finish. • 1.5 HP Motor, 3 Phase Motor. • GI wire ropes with steel core at center. • Curtain holding trollies placed uniformly at specific interval of 200mm /250 mm throughout the track. • Diverter pulley • MS yellow passivized Routing pulleys with ball bearing for smoother noiseless movement 165mm for outer diameter, 145mm diameter at groove base with 12mm pulley thickness. • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish.

Frill Bar, length 10 Mtrs made using 40NB, 48mm OD construction arrangement 2mm Thickness undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with suitable suspenders.

MS, Wing frame made out of 25X25mm or higher size made of MS square pipe with 2mm in thickness undergone through various chemical treatment to keep them rust free and duly powder coated in black matt texture finish with Below Specifications: • Wing Frame Size 5.5 x 1 Mtr • 1.5meter wing track of 48x84mm with grid mount brackets made of 40X50X40mm C track, • Pivotable 4 wheeled suspension trolley, • Adjustable floor locking screw jacks with rubber grips, • Inverted 4-Wheeler Trolley with Flexi Adaptor Clamp, • Heavy duty wing track to be laid for minimum length of 1.5mtr, along the width of the stage. • 360° Rotatable and can move in unidirectional • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish.

MS Fabricated 4 way 10A, 250V A.C, IEC, Lighting Junction box made up of 22SWG CRCA for LED lighting fixtures with Pipe clamp arrangement for fixing on pipe grid or Raul plug arrangement for wall/floor fixing, duly black epoxy polyester powder coated texture finish.

MS Fabricated 2 way 10A, 250V A.C, IEC, Junction box made up of 22SWG CRCA with rocker switch to power up splitter and console with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, duly black epoxy polyester powder coated texture finish.

MS Fabricated 5 pin DMX Signal IN Junction box fitted with 5 pin DMX Male socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish.

MS Fabricated 5 pin DMX Signal OUT Junction box fitted with 5 pin DMX female socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish.

Fabricated 5 pin DMX Signal loop Junction box fitted with 5 pin DMX Male & Female socket with 0.3 Mtr DMX Loop cable fitted with 5 pin DMX cable mount plug, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish.

Well designed 12 Way Direct Lighting Distribution Board made up of CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt texture finish consists of R, Y, B Indicator lamp, 32A TPN incomer, SP Mcb's and for the junction boxes fixed on the top of the light bar including wiring and busbar connection with proper earthing and Hingable door with magnetic door lock complete.

Auxiliary marshalling box for power and signal cable termination in grid level and in Motorised Light bar • CE Marked FC/PG cable entry gland required Nos as per cable entry. • MS channel arranging to fix terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. • Grey terminal connector with each line having P, N, E Indication for each line incoming and out going cable connectors. • Box door must be made with Hingeable door with screw lock. • Made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish.

Motor Cable Termination box for power cable termination at grid level. • CE certified FC/PG 11 & 13.5 cable entry gland required Nos as per cable entry. • MS channel arranging to fix grey terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. • Grey terminal connector with each line having L1, L2, L3, E, 6, 2, 4 Indication for each line incoming and outgoing cable connectors (L1, L2, L3, E for Power supply & 6 , 2 , 4 for Limit Switch connection) • Box door must be made with Hingeable door with screw lock. • Grid mount fixing arrangement for fixing on grid or Anchor fastener for wall/floor fixing • MS Boxe made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish.

RDM Compatible DMX Splitter unit with Minimum following specifications. ● 1 Nos 5 Pin DMX In socket and 8 Nos 5 Pin DMX Out socket ● In and out signal Optically Isolated ● LED Indicator for check the signal flow in output. ●Suitable for standard 19” cabinet ● Duly black epoxy polyester powder coated texture finish.

Digital Lighting console with Minimum following specifications. ● 512 Channel, 2 Output ● No. Of Direct Fixture Control : Atleast 200 or more ● No. Of Faders : Atleast 12 ● Atleast 4 Encoder Wheels ● 7" Touch screen display for navigation ● Backlight Keyboard ● Numeric Key Board

5 pin XLR male / female connectors of made up of Extra high temperature resistant insulator material, Larger solder contacts for easier termination.

5 Pin XLR Termination plug made up of extra high temperature resistant insulator material, Larger solder contacts for easier termination with 120 Ohm resister with 0.25Watt for signal termination.

Main Valance Fabric : Fire retardant velvette fabric 100% (2 times of the finished dimension) gathering for main scallop as per the approved patern and colour, not less than 250 GSM, duly stitched along with and eyelets. Size : 12.5 x 1 Meter

Main Curtain Fabric : Fire retardant velvette fabric with lining 100% (2 times of the finished dimension) gathering as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 16 x 5.5 Meter

Rear Curtain Fabric : Fire retardant cotton fabric 50% gathering for as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 14 x 5.5 Meter

Frill Fabric : Fire retardant cotton fabric 50% gathering for as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 10 x 1 Meter

Wing Fabric : Fire retardant cotton fabric 0% gathering for as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 5.5 x 2.1 Meter

PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 3cx1.5 sq mm.

PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 4cx 4 sq mm.

PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 7cx1.5 sq mm.

FR Grade DMX Signal 4 core + Ground shielding Cable with CE mark for the Signal network.

MS perforated tray of Size 40 x 75 x 40mm & 1.6 mm Thickness undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish along with clamping arrangement.

Internal earthing copper bare conductor of size 14 SWG for power network related to work coming under our scope.

Installation hardware’s such as clamps, connectors, glands, lugs, ferrules, welding rods and miscellaneous items required during installation work.

Installation, Testing, Commissioning of Stage Lighting & Furnishing System.

Please Enable Macros to View BoQ information