Construction of Anganwadi Building at Irulanchandaipet, Bahour Constituency, Puducherry.

Amount

Code No:2.8.1:- Earth work in excavation by mechanical means (Hydraulic excavator ) /manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m -All kinds of soil.

CODE NO:2.25:- Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m.

CODE NO:2.27:- Supplying and filling in plinth with sand under floors including, watering, ramming consolidating and dressing complete.

CODE NO:4.1.3:- Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

CODE NO:4.1.8:- Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:4:8 (1 cement: 4 coarse sand : 8 graded stone aggregate 40mm nominal size)

CODE NO:7.1B.MO:- Cement concrete 1:3:6 mix with stone aggregates 20mm nominal size mechanically mixed and vibrated in foundation upto a depth of 1.5 metres below ground level and 1.5 metres ground/bed level.

CODE NO:4.1.10:- Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40mm nominal size)

CODE NO:5.33.1:- Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work , using cement content as per approved design mix , including pumping of concrete to site of laying but excluding the cost of centering , shuttering , finishing and reinforcement , including admixtures in recommended proportions as per IS : 9103 to accelerate, retard setting of concrete , improve workability without impairing strength and durability . Note:- Cement content considered in this item is @ 330 kg / cum. Excess or less cement used as per design mix is payable or recoverable separately. - All work upto plinth level

CODE NO:5.33.2:- Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work , using cement content as per approved design mix , including pumping of concrete to site of laying but excluding the cost of centering , shuttering , finishing and reinforcement , including admixtures in recommended proportions as per IS : 9103 to accelerate, retard setting of concrete , improve workability without impairing strength and durability . Note:- Cement content considered in this item is @ 330 kg / cum. Excess or less cement used as per design mix is payable or recoverable separately. - All work above plinth level upto floor V level

CODENO:5.9.3:- Centering and shuttering including strutting , propping etc and removal of form for - Suspended floors , roofs landings , balconies and access platform

CODE NO:5.9.5:- Centring and shuttering including strutting, propping etc. and removal of form for: lintels, beams, plinth beams, girders, bressumers and cantilevers.

CODE NO:5.9.19:- Centring and shuttering including strutting, propping etc. and removal of form for: Weather shade, Chajjas, corbels etc., including edges. -

CODE NO:5.16:- Providing , hoisting and fixing upto floor five level precast reinforced cement concrete in shelves including setting in cement mortar 1:3 (1 cement : 3 coarse sand) , cost of required centering , shuttering and finishing with neat cement punning on exposed surfaces but excluding the cost of reinforcement , with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size)

CODE NO:5.22.7:- Steel reinforcement for R.C.C.work including straightening , cutting , bending , placing in position and binding all complete upto plinth level - Thermo -Mechanically treated bars (ISI BRAND OF APPROVED MAKE) Fe - 415 or more

CODE NO:6.1.1:- Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in foundation and plinth in - cement mortar 1:4 (1 cement : 4 coarse sand)

CODE NO:6.1.2:- Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

CODENO:6.4.2:- Brick work with common burnt clay F.P.S (non modular ) bricks of class designation 7.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 coarse sand)

CODENO:6.13.2:- Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level - cement mortar 1:4 (1 cement : 4 coarse sand)

CODENO:8.2.2.2:- Providing and fixing 18mm thick gang saw cut, mirror polished (premoulded and prepolished) machine cut for kitchen latforms, vanity counters, window sills, facias and similar locations , of required size, approved shade,colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing,curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels - Raj nagar plain white marble / Udaipur green marble / Zebra black marble - area of slab over 0.50 sqm

CODENO:8.3.2:- Providing edge moulding to 18mm thick marble stone counters ,vanities etc., including machine polishing to edge to give high gloss finish etc. complete - Granite work

CODENO:9.1.2P:- Providing wood work in frames of doors , windows, clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Padak wood

CODENO:9.21.1:- Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part 1) non-decorative type, core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. - 35 mm thick including ISI marked stainless steel butt hinges with necessary screws

CODE NO:9.48.2:- Providing and fixing M.S.grills of required pattern in frames of windows etc with M.S. flats , square or round bars etc. including priming coat with approved steel rimer all complete - Fixed to openings / wooden frames with rawl plugs screws etc

CODE NO:9.53:- Providing 40x5 mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

CODE NO:9.62.1R:- Providing and fixing ISI marked powder coating sliding door bolts with nuts and screws etc. complete - 300x16mm

CODE NOS:9.63.1R:- Providing and fixing ISI marked powder coating tower bolt black finish, (barrel type) with necessary screws etc. complete:- 250 x 10mm

CODE NO:9.63.4R:- Providing and fixing ISI marked Powder coating tower bolt black finish, (barrel type) with necessary screws etc., complete:- 100 x 10mm

CODENO:9.66.1R:- Providing and fixing ISI marked powder coating handles conforming to IS : 4992 with necessary screws etc., complete : 125mm

CODENO:9.66.2R:- Providing and fixing ISI marked powder coating handles conforming to IS : 4992 with necessary screws etc.complete : 100 mm

CODENO:9.95.5:- Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc., complete :100 x 63 x 3.2mm

CODE NO:9.117.2:- Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance +_ 1mm ), with wall thickness 2.0 mm (+-0.2mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws , joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19 x 19 mm and 1mm (+-0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification - Extruded section profile size 42 x 50 mm size 42x50mm.

CODE NO:9.118.1:- Providing and fixing to existing door frames - 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59 x 24 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt edging on both sides . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws . The styles of the shutter reinforced by inserting galvanised M.S.tube of size 20x20 mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of 'H' section , a uPVC hollow section of size 100 x 24 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer's specification (For W.C. and bathroom door shutter)

CODE NO:9.165.1A:- Providing and fixing of 65mm Godrej Navatal lock of 6 levers etc complete

CODE NO:10.11.1:- Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators , side /top/centre hung, with beading and all members such as F7D,F4B,K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings , complete all as per approved design, (sectional weight of only steel members shall be measured for payment) - Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C.1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20mm nominal size)

CODE NO:11.3.1:- Cement concrete flooring 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm nominal size stone aggregate.

CODE NO:11.36D:- Providing and fixing commercial quallity ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacture of approved make (Jhonson / Asian / Somany / Nitco) in all colours, shades of size 200 x 300 mm as approved in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry slurry @ 3.3 kg per sqm. Including pointing in white cement mixed with pigment of matching shade complete. - size 200x300mm

CODE NO:11.37.3:- Providing and laying ceramic glazed floor tiles 300X300mm (thickness to be specified by the manufacture) of commercial quality conforming to IS : 15622 of approved make (Nitco / Kajaria ) in colours such as white, ivory, grey, fume red, brown laid on 20mm thick cement mortar 1:4(1 cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete

CODE NO:12.15.1:- Painting top of roofs with bitumen of approved quality at 17kg per 10sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete: With residual type petroleum bitumen of grade VG-10

CODE NO:12.20:- Providing and laying pressed clay tiles (as per approved pattern 18mm nominal thickness and of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% intergral water proofing compound laid over a bed of 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete.

CODE NO:12.42.3.2:- Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single Tee with door 110X110X110mm.

CODE NO:12.42.5.2:- Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Bend 87.5deg. 110mm bend.

CODE NO:12.43.2:- Providing and fixing unplasticised - PVC clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm

CODE NO:13.8.3:- 12 mm cement plaster of mix - 1:5 (1 cement : 5 fine sand)

CODE NO:13.9.2:- Cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement 20 mm cement plaster.

CODE NO:13.9.2A:- 15mm cement plaster on the rough side of single or half brick wall of mix 1:5 (1 cement : 5 fine sand)

CODE NO:13.16.1:- 6mm cement plaster of mix 1:3 (1 cement : 3 fine sand).

CODE NO:13.43.1:- Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer

CODE NO:13.46.1:- Finishing walls with acrylic smooth exterior paint of required shade - New work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm

CODE NO:13.50.1:- Applying priming coat - with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

CODENO:13.61.1:- Painting with synthetic enamel paint of approved brand and manufacture to give an even shade - Two or more coats on new work.

CODE NO:16.1:- Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

CODE NO:16.63:- Providing wall black board with cement mortar 1:3 (1 cement :3 sand) finishing with a floating coat of neat cement and charcoal powder mixed in the proportion 1:2 (1 cement : 2 charcoal powder) and applying one coat of black board paint including 20mm thick cement plaster band 50mm wide in cement mortar 1:3 (1 cement : 3 sand)

CODE NO:16.94:- Supplying fixing and commisioning of Suguna/ Texmo /Sharp 0.5 HP monoblock pumpset slow speed single phase motor. The rate include the cost of pumpset, pumpset fixing in position and test run etc., complete.

CODE NO:17.10.2.3:- Providing and fixing stainless steel AISI 304 (18/8) Kitchen sink as per Is 13983 with CI brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required - Kitchen sink without drain board - 470x420 mm bowl depth 178mm

CODE NO:17.13.2:- Providing and fixing white vitreous china water closet squatting pan (Indian type) Orissa pattern WC pan of size 580 x 440mm.

CODE NO:17.28.1.2:- Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete - Semi rigid pipe - 40mm dia.

CODE NO:17.60.2.1:- Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors 100 mm inlet and 75 mm outlet sand cast iron S&S as per IS 3989.

CODE NO:17.70.2:- Providing and fixing PTMT bottle trap for wash basin and sink. Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 263 gm.

CODE NO:18.9.11:- Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall) - 20mm nominal outer dia pipes

CODE NO:18.9.31:- Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings this included jointing of pipes & fittings with one step ASTM solvent cement, trenching refilling & testing of joints Complete (External work) - 20mm nominal outer dia pipes

CODE NO:18.10.1:- Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls etc. Internal work - exposed on wall 15mm dia nominal bore.

CODE NO:18.16.2:- Providing and fixing brass stop cock of approved quality - 20 mm nominal bore.

CODE NO:18.18.3:- Providing and fixing ball valve (brass) of approved quality high or low pressure with plastic floats complete. - 25 mm nominal bore.

CODE NO:18.48A:- Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet outlet and overflow pipes but without fittings and the base support for tank - Circular Tank

CODE NO:18.49.1:- Providing and fixing CP brass bib cock of approved quality conforming to IS 8931 - 15mm nominal bore.

CODE NO:19.33:- Constructing soak pit 1.20 x 1.20 x 1.20 m filled with brickbats including S.W.drain pipe 100 mm diameter and 1.20 m long complete as per standard design

CODE NO:19.33.1:- Providing and fixing on wall /column face unplasticed - PVC soil and waste pipes (type-B) conforming to IS:13592-1992 including jointing with seal ring conformation to IS: 5382 leaving 10mm gap for thermal expansion - single socketed pipes 110mm diameter

CODE NO:19.33.1A:- Providing and fixing on wall face/column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion - Single tee with door - 110x110x110mm

CODE NO:19.33.2:- Providing and fixing on wall/column face unplasticised - PVC soil and waste pipes (type B) conforming to IS:13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - single socketed pipes 75mm diameter

CODE NO:19.33.2C:- Providing and fixing on wall face / column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 75mm

CODE NO:31.5.1B:- Making connection of UPVC distribution branch with Upvc main of following sizes by providing and fixing tee including cutting the pipe etc., compete.-110mm dia to 160mm dia nominal bore.

BOOBALAN M

R MANOGARAN