C/O Separate Water Supply Scheme for the Baliwal Village of Haroli Constituency Distt. Una (HP)

Amount

Excavation in foundation and trenches up to all depths and in all classification of earth work such as Pick work, Jumper work, chiselling or wedging out of soft and hard rock as blasting is prohibited, saturated soil including bailing or pumping out of water, including cutting of bitumenous/concrete surface wherever required, in all lifts including trimming and dressing of sides, levelling of beds to correct grade including shoring, strutting , planking, timbering and dewatering where ever required. Stacking usable and unusable material /soil seperataly and after laying, jointing and testing of pipes (for pipes, Pipe duct, chambers, x-sings etc.), returning the usable soil in 15cm layers by ramming and watering and then disposing of all surplus excavated soil/ unusable material as directed within all leads/ lifts and including cost of diversion for traffic, night signal boards, fixing caution boards, crossing over trenches for access to houses, fencing etc. complete in all respects within all leads and lifts as per direction of the Engineer-in-charge.

Providing and laying Cement Concrete 1: 3: 6 ( 1 cement : 3sand: 6 graded stone aggregate 20 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts and as per the direction of the .Engineer-in-Charge.

Providing and laying cement concrete using M - 25 graded stone aggregate 20 mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in :

Foundation,footing & bases of columns and the like mass concrete with in all leads and lifts complete in all respect as per the direction of the Engineer-in-charge.

Wall (any thickness,but not less than 0.10 mtr.thickness) attached pilasters,buttresses,plinth & string courses etc. upto all heights complete within all leads and lifts as per the direction of the Engineer-in-charge.

Providing and laying cement concrete using M - 30 graded stone aggregate 20 mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in :

Suspended floor roofs, landing and shelves and their support balconies, beam girderes bressumers and cantiliver upto all heights in all leads and lifts and as per the direction of the Engineer-in-Charge.

Arches upto 6.00 mtrs span, all heights complete within all leads and lifts as per the direction of the Engineer-in-charge.

Providing form work with steel plate 3.15 mm thick welded with angle iron frame 30x30x5mm so as give a fair finish including centring, shuttering, strutting and propping etc with wooden battens and ballies, height of propping and centring below supporting floor to ceiling upto any height and removal of the same for in site-reinforced concrete and plain concrete work in

Vertical surfaces such as walls (any thickness) partitions and the like i/c attached pillasres buttresses, plinth & string courses and the like including all leads and lifts complete in all respect.

Flat surfaces such as soffits of suspended floors,roofs,landing and the like floor etc. up to 20 mm in thickness including all leads and lifts complete in all respect.

Providing of form work of ordinary timber planking so as to give a rough finish including centering, shuttering , strutting and propping etc. height of propping and centering below supporting floor to ceiling and removal of the same insitu reinforced concrete and plain concrete work in all leads and lifts and as per the direction of the Engineer- in - Charge. Arches beyond 6.00 mts.span

Providing RCC work smooth finishing of the exposed surface with cement mortor1:3 (1cement:3 sand ) in all leads and lifts and as per the direction of the Engineer-in-Charge.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete in all respect in all leads and lifts & as per direction of the Engineer-in-Charge

Steel work welded in built up sections,trusses and framed work including cutting hoisting fixing in position and applying a priming coat of red lead paint in all lead and lifts as per the direction of the Engineer-in-Charge.

Providing Fixing of GMS pipe (M) with MS flange (T) Joint 100 mm dia for inlet,outlet,overflow & scour pipe in all tanks complete within all lead and lifts as per the direction of the Engineer-in-Charge.

Providing and fixing C.I.sluice valve ( With hand whell ) of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make as per IS 780 class for following dia ( including brass spindle and as per IS 2906 class-II including MS Flange, bolts, nuts, rubber insertion etc. complete in all respect i/c carriage of material complete within all lead and lifts as per the direction of the Engineer-in-Charge. 100 mm dia Class PN-1.00

Constructing chamber for sluice valve, with CI surface box 100 mm top dia.,160 mm bottom dia. & 180 mm deep(inside) with chained lid RCC top 1:2:4 mix (1 cement :2 sand :4 graded stone aggregate 20 mm nominal size) 100mm thick foundation concrete 1:5:10 mix (1cement : 5 sand : 10 graded stone aggregate 40 mm nominal size) & inside plastering with cement mortor 1 :3 (1 cement : 3 sand) finished with a floating coat of neat cement i/c curing complete. 600 x 600 x 750 mm inside size With 150 mm thick walls of RCC 1:2 :4 (1 cement :2 sand :4 graded stone aggregate 20mm nominal size) complete with form work & reinforcement with 6 mm bars at not exceeding 150 mm centres both ways

Provind & foxing SFRC Manhole cover with frame having frame size of 560 mm internal dai should not be less than 100 Kg with with locking arrangement complete in all respect including all leads and lift.

Providing, Laying, jointing and testing & Commissioning of bevelled ended GMSERW pipe with circumferential butt welded joints (95% welded and 5 % flanged) wherevever required by electrical arc welding (welding thickness shall be equal to pipe wall thickness) and testing of GMSERW pipe of following dia metres conforming ot IS 3183-2012, having wall thickness as specified below capable of withstandig required test pressure, including manufacturing and fabrication of reducers/tapers, all short pieces, bends etc as per site requirement made from parent tubes. The laying of pipe shall also include welding of flanged joint of duly welded every sistrn pipe in three layers (one inner two outer) and all operations such as cutting, welding, jointing, fabrication of bends, tees making bevelled pipe ends suitable for butt welding, lowering & laying in excavated trenches to ensure required level complete in all respect to the best satisfaction of the Engineer-in-charge (Earth work in treches and the cost of providing flanges i/c nut & bolts, gasket and circumferential butt welded joints will be measured and paid for separately). The fabricated bends should have three or four cuts having radius not less than 5 times of diameters of pipe. The welding electrodes shall be as per IS 814 of Advani, Oerlikon/L&T of ISI make. The damaged portion of pipe if damaged during laying/jointing, operation of pipe all other special made for the parent tube shall be AWWA specification C-203-1978. The rate also include entire darriage of material, flushing, cleaning and testing pipe D.P. test of but welded joint complete in all respect & best satisfaction & direction of Engineer in Charge.

100 mm dia GMSERW pipe (L-290 X42) 4.80 mm thick . (For R/Main No. 1 from RD RD. 0 to 25 & Rising Main No. 2 from RD. 0 to 7450.

Providing and welding M.S. flanges @5% at suitable point, conforming to following tables as per IS: 6392-1971 (Latest with upto date amendments) with plain end GMS/MSERW pipe in three number (2 outer and 1 inner) of layers on both faces to make the joint leak proof (The cost of providing and laying of MSERW pipes to be measured and paid for seprately). The welding of flanges should conform to IS:816-1969 with electrodes as per IS: 814-1991 and required number of nuts and bolts conforming to IS 1364. including cost of gasket sheet nuts & bolts. The thickness of gasket sheet not less then 3.00 mm conforming to IS 2712-1998. The work shall be done to the entire satifaction of engineer in charge with in all leads and lifts to the entire satisfaction of Engineer-in-Charge.

MS flange 100 mm dia Table- 38 for Rising Main No. 2 from RD. 0 to 1530

MS flange 100 mm dia Table- 28 for Rising Main No. 2 from RD. 1530 to 5100.

MS flange 100 mm diaTable- 17 for Rising Main No. 2 from RD. 5100 to 6630..

MS flange Table- 5 for Rising Main No. 2 from RD. 6630 to 7450. & For R/Main 1. RD. 0 to 25..

Providing circumferential butt welded joints by electrical arc welding to GMERW pipe, welded in requisite number of weld runs so as to achieve the minimum effective throat thickness of weld conforming to IS 816-1969 specifications, by using welding electrodes conforming to IS 814-1991 at site of work complete in all respects, including manual/mechanical handling of pipes in all leads and lifts to the entire satisfaction of Engineer-in-Charge.

Supply of submersible pumping set of reputed make such as KSB/ Calama / BS/ Worthigton / Sabar/ Seerex /Johnston / Amrut confirming to latest relevent BIS . The pump should be fitted with free fine impellers of suitable alloys as per BIS ; 5659-1978 with upto date amendments, suitable for raw / clear water having greased packed bearing and shell with wound stator on motor side and with shaft protection on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to submersible motor of same as that of offered submersible pump make confirming to BIS ;9283-1979 with upto date amendments, totally dust and water proof for submersible pump, duly isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed, lubricated bearing and provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear tear.It should also be fitted with a device to make up expantion of water with heating of motor. The pumpset should include water level guard i/c cable ,errection clamps, cable clips and depth gauge etc. and suitable for opertion on data given below. a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation

Discharge, (Q) = 8.99 LPS

Total Head ( H ) = 10.91 Mts.

a) SWL in Tubewell = 0.00 Mtr. bgl.

c) R.L. point of discharge = 387.45 Mtr.

d) Seasonal fluctuation + draught condition + bowl assembly. 6.00 Mtrs.

e) Drawdown in Tubewell 2.00 Mtrs.

f) R.L of lowest point of pumpset installation = 378.45 Mtrs.

g) Static Column lift = 6.00 Mtrs.

Rising main. Column Pipe.

Length 25 Mtrs. Length 6.00 mtrr.

Dia meter 100 mm Dia 100 mm

Class GMS pipe (M) Class GMS pipe (M)

Pumping hours 8 hours

Altitude of installations above M.S.L. __________mtr.

Characteristic of water.

a) Temperature _______ Deg Cel.

b) Turbidity ________JTU.

c) Allkanity. ___________mg/ l Ca Co3

d) Size of solids ____________mm

e) others

Depth of T/well mtr.

Dia of T/ well assembly 200 mm.

Length of assembly pipe.

Dia of housing pipe 300 mm.

Length of housing pipe

OPERATING CONDITIONS.

Type of Current :- A.C.Three Phase.

Frequency:- 50 Cycles /Sec.

Rated Voltage 415 +/- 15 % Volts.

System of earthing: Double Loop earthing as per BIS 3843-1987 Latest.

Speed of Revolution ____________ RPM 2900

MOTOR.

Ref. to BIS code BIS 9283-1979 with upto date amendments.

Type of enclosure of motor: As per BIS ; 4691-1985 ( latest )

Mechanical out put in H.P.

Class of insulation :Class B

The motor should be able to withstand initial current of 2.50 times the rated current for two minutes without suffering damages of permanent deformations.

Ref. to BIS code ; BIS ; 5659-1978 with upto date amendments.

Drive Type: Electric driven.

Operating Range: -15 % to+10 % of Total head at duty point.

Deliver size of Pump : ________( To be quoted by tenderer.)

Supply, Installation, testing and Commissioning of fully Automatic LT pannel for submersilble pump made out of 16 gauge sheet podwer coated dust and vermin proof wall mounted and front opening door type switch board with copper insulated wiring suitable to operate Pump of rating HP automatically through variable frequency drive starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and oof command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. make Aarmation Electric Private Limited/MAS/ELLWS.

Variable frequency drive starter of desired HP Heavy duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It should be capable to control the frequency of pump through out the operation and also should be capanle to maintain the power factor of the system within acceptable limits. It should have ambient temperature 50 Degree without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. make Aarmation Electric Private Limited/MAS/ELLES.

Multi function meter indicating different parameters like current, voltage, KWH, PF, THD etc with Rs. 485 communication make L&T/Conserve/Siemens.

MCB/MCCB suitable capacity of L&T/Standard make on the coming feeder for pumping set confirming to BIS 2516-1985 (Latest edition) with netural linked under voltage release.

Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452(Part-I & II) latest with upto date ammendments.

Incommer MCCB with for proper short circuit capable for both the starters make L&T/Schnieder/ABB.

On/Off indicator and push button, Control and power wiring, power capacity, cooling fan 230 VAC, Control terminal, Buss bar, i.e. Bolt insulator, etc.

Input Choke which should be installed at the input of VFD starter, so that there should be proper protection in case of any voltage surge and distortions in single.

Control Transformer to safeguard the control circuit of all the components from the voltage surges and spikes.

Output contactors in the output ofVFD to run the pump.

Programmable logic controller with appropriate digital and analog inputs and outputs to give automatic command to star delta and also will get data from function meter for currint, voltage, KWH, PF and THD, mak mitsubishi/L&T/delta.

HMI 7" display with IOT to give on and off command manually and also to show pump running and breakdown status at pump station make Wientek/Exor/Mitsubishi/Mecon.

Supply of software with license to monitor data at Laptop/Mobile in from of Software and Mobile Application for 3 users.

Level Sensor to indicate the water level of tank remotely.

Cloud Gate/Way for date cluding to server.

Cabale for communication for water level Sensor.

Providing and fixing of double flanged cast iron Sluice valve of leader/ Kirlosker make for column pipe of Pump and capable of with standing the normal seat pressure and as per IS 6312-1984 P-1 for coulmn Pipe 100 mm dia class PN-1.00 class PN 1.0 of Kirloskar/Kilburn/Leader make conforming to BIS latest with upto date ammendments having seat pressure 16.32/ cm2 complete in all respect. Within all leads and lifts.

Providing and fixing of double flanged cast iron Reflux valve of leader/ Kirlosker make for having by pass arrangment class PN 1.6 conforming to relevants BIS 1868-API -600 latest edition) to be provided on delevery side ) of size one step heigher than the delevery size of pump and should be suitable for with standing nominal seat pressure 16.32 Kg/cm2.

Providing and laying PVC insulated jointless flat water proof copper cable of Siemens/Finolex/Grandlay/ Gloster make conforming to BIS-1554 (Part-I)-1988 or (latest with upto date ammendments) of suitable size for the pump sets offered (One cable carrying all three phases) including all other electrical equipment/ accessories such as thimbles, flexible pipe, solder, nut & bolts cable glands etc. laid in pipes or trenches under floor, The type, size & make will be subject to approval of HPSEB authorities. In case of non acceptance by HPSEB authority, it shall have to be replaced by the tenderer free of cost.

Supply & errection of floor power factor shunt capacitor conforming to BIS: 2834-1986 latest with upto date amendments GEC/Siemen/Havells L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually of required KVAR according to BHP of motor offered including Standard/L&T/Kilburn/ Indo asian mak ICTP switches conforming to BIS-4064-1978 or latest with HRC fuses (range to be specified by the tendrerer)

Supply of standard make 100mm dia circular dial pressure gauge of suitable range of Feibeg/Bourden/Precision make with all accessories such as stop cock, copper tubing etc, conforming to BIS: 3624-1987 latest with upto date amendments.

Providing and laying column aseembly of GMS pipe (M) considering site requirements and having appropriate size in accordance with the delivery size of pumping set. The pipe shall conform to relevant BIS code & capable of with standing the feiled test pressure equal to 1.5 times the operating pressure including all type of fitting such as bends, tapers/ reducers, flanges, rubber, gaskets 3mm thick nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer in charge. The pipe material shall confirm to relevant BIS code and capable of withstanding FTP equal to 1.50 times the operating pressure the complete arrangement shall be compromise of.

Installation of all items appearing as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing horizontal spindle, horizontal / radial split casing /end suction ( back pull out arrange-ment) Single /double /multi stage of Kirloskar / KSB Crompton KSB/Calama/BS/ Groundfos/ Hindustan/ Lubbi make as per BIS IS 1520-1980 with upto date ammendments read with IS: 9137-1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron / cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring / Squirrel cage screen protected drip proof induction motor / motors of standard make such as Crompton / NGEF / GEC / Seimens /Jyoti/ Kirloskar BHEL / ABB suitable for operation on 415 (+/-15%) volts. 50 Cycles /Sec. 3 phase AC electric supply of 2900 RPM.The power of electric motor/ motors should be at least +10% in excess of the maximum power required by the pump / pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor / motors as per IS 325 IS -1978 with upto date amendments read with IS 900 -1972. It should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements. (a) Pump :- Specifications i) Make ii) Model iii) No. of stages iv) Manfacurer's certificate to be attached. performance i) Discharge ii) head Make ii) Model iii) efficiency of pump a) duty Head b) (+) 10% duty head c). (-) 15% Duty Head d) performance curve to be attached b). Motors:- Specificions Make ii) Model iii) Rating iv). speed v) Insulation (C) Coupling (D) Base plate

Discharge = 8.99 LPS

Total Head:- 420.32 mtrs.

Supply, Installation, testing and Commissioning of fully Automatic LT pannel for submersilble pump made out of 16 gauge sheet podwer coated dust and vermin proof wall mounted and front opening door type switch board with copper insulated wiring suitable to operate Pump of rating HP automatically through variable frequency drive starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and oof command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. make Aarmation Electric Private Limited/MAS/ELLWS.

Variable frequency drive starter of desired HP Heavy duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It should be capable to control the frequency of pump through out the operation and also should be capanle to maintain the power factor of the system within acceptable limits. It should have ambient temperature 50 Degree without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. make Aarmation Electric Private Limited/MAS/ELLES.

Multi function meter indicating different parameters like current, voltage, KWH, PF, THD etc with Rs. 485 communication make L&T/Conserve/Siemens.

MCB/MCCB suitable capacity of L&T/Standard make on the coming feeder for pumping set confirming to BIS 2516-1985 (Latest edition) with netural linked under voltage release.

Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452(Part-I & II) latest with upto date ammendments.

Incommer MCCB with for proper short circuit capable for both the starters make L&T/Schnieder/ABB.

On/Off indicator and push button, Control and power wiring, power capacity, cooling fan 230 VAC, Control terminal, Buss bar, i.e. Bolt insulator, etc.

Input Choke which should be installed at the input of VFD starter, so that there should be proper protection in case of any voltage surge and distortions in single.

Control Transformer to safeguard the control circuit of all the components from the voltage surges and spikes.

Output contactors in the output of VFD to run the pump.

Programmable logic controller with appropriate digital and analog inputs and outputs to give automatic command to star delta and also will get data from function meter for currint, voltage, KWH, PF and THD, mak mitsubishi/L&T/delta.

HMI 7" display with IOT to give on and off command manually and also to show pump running and breakdown status at pump station make Wientek/Exor/Mitsubishi/Mecon.

Supply of software with license to monitor data at Laptop/Mobile in from of Software and Mobile Application for 3 users.

Level Sensor to indicate the water level of tank remotely.

Cloud Gate/Way for date cluding to server.

Cable for communication for water level Sensor.

Installation of all items appearing as above as per the systematic drawing atached with the dacoments or as per the systematic drawing attached wih the dacoments or as per the direction of the Engineer-in-Charge.

Providing and fixing of double flanged cast steel Sluice valve 100 mm dia of Kirloskar/Leader make cfor the delivery line of pump and capable of withstanding the normal pressure and as per IS 14846(Cast Steel) with latest ammendments Classs: ASA 300 API 6D.

Providing and fixing of double flanged cast steel Sluice valve 100 mm dia of Kirloskar/Leader make cfor the delivery line of pump and capable of withstanding the normal pressure and as per IS 14846(Cast Steel) with latest ammendments Classs: ASA 300 API 6D.

Providing and laying PVC insulated jointless flat water proof copper cable of Siemens/Finolex/Grandlay/ Gloster make conforming to BIS-1554 (Part-I)-1988 or (latest with upto date ammendments) of suitable size for the pump sets offered (One cable carrying all three phases) including all other electrical equipment/ accessories such as thimbles, flexible pipe, solder, nut & bolts cable glands etc. laid in pipes or trenches under floor, The type, size & make will be subject to approval of HPSEB authorities. In case of non acceptance by HPSEB authority, it shall have to be replaced by the tenderer free of cost.

Supply & errection of floor power factor shunt capacitor conforming to BIS: 2834-1986 latest with upto date amendments GEC/Siemen/Havells L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually of required KVAR according to BHP of motor offered including Standard/L&T/Kilburn/ Indo asian mak ICTP switches conforming to BIS-4064-1978 or latest with HRC fuses (range to be specified by the tendrerer)

Supply of standard make 100mm dia circular dial pressure gauge of suitable range of Feibeg/Bourden/Precision make with all accessories such as stop cock, copper tubing etc, conforming to BIS: 3624-1987 latest with upto date amendments.

Fixing double flanged GMS (M) piping work (layout to be approved by the Engineer-in-Charge). for suction and delivery pipes suiabe to pump offered and common header as per the rising ma respectively completewith specials such as bends, tees, reducers/ increasers with companion flanges atching with the relevant specifications of the as indicated in drawingincluding rubber/ asbestos gasket of 3 mm thickness as per IS: 2712-1972 and required number of Nuts and bolts as per 1364-1983. The pipe material shall confirm to relevant BIS code and to withstanding 1.50 times of total Head.

Suction pipe. 100 mm dia GMS(M) 4.80 mm thick

Delivery pipe 80 mm dia GMS (M) pipe.

Common header pipe 100mm dia. GMS(M) pipe.

Providing and fixing double loop earthing with GI plate of 600x600x6.30 mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt 25x5 mm strip as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge.

aditya govt. contractor

M/S OM PARKASH DHIMAN AND SONS

Sushant Puri

abhishek khajanchi

MS Kamal Dev Sharma

gagan ohri

dinesh kumar lath

Ravinder Kumar Sahore

M/s Ashwani Kumar Govt. Contractor

HYDRAULIC ENGINEERING COMPANY

P C Construction

RAM KISHAN CHANDEL