C/O Store, office accommodation for Horticulture/Agriculture at Spillow in District Kinnaur HP (SH- Building portion, water supply and Sanitary Installation, C/O Septic Tank, Rain water harvesting system and site development

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains , including dressing of sides and ramming of bottoms, upto all lead and lifts , including getting out the excavated soil and disposal of surplus excavated soil as directed, upto all lead. All kinds of soil, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Supplying and filling in plinth with sand under floors,including watering, ramming, consolidating and dressing complete, as per PWD specifications and as per direction of the Engineer-in-charge.

Boulder filling dry hand packed under flooring,including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Centering and shuttering including strutting, propping etc. and removal of form , complete: including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Foundations, footings, bases of columns, etc.for mass concrete

Suspended floors, roofs,landing,balconies and access platform

Columns, Pillars,Piers,Abutments ,Posts and Struts

Stairs, (excluding landing )except spiral staircases

Linteles,beams,plinth beams,girders,,bressumers and cantilevers

Edges of slab and breaks in floor and walls Under 20 cm wide

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Providing and laying cement concrete 1:5:10 (One cement : five sand : ten graded stone aggregate 40mm (Forty millimeter) nominal size) and curing complete excluding the cost of form work in Foundation and plinth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 one Cement : 4 four coarse sand : 8 eight graded stone aggregate 40mm (fourty millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:2:4 (One cement : two sand : four graded stone aggregate 20mm (Twenty millimeter) nominal size) and curing complete excluding cost of form work in: Foundation and plinth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying reinforced cement concrete 1:1.5:3 (One cement : one point five sand : three crushed stone aggregate 20mm. (Twenty millimeter) nominal size) mechanically mix by concrete mixer and compacting the concrete with vibrator and curing complete excluding cost of form work and reinforcement for R.C.C. work, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo Mechanically Treated bars of grade Fe-500D or more , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Construction of dry rubble masonry for R/walls, breast wall , revetment wall and parapets etc. for sub structure and super structure complete as per drawing and technical specfication clause 704.6 and 1302.5 , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Coursed rubble masonry (first sort) with hard stone in foundation and plinth with : Cement mortar 1:6 (1 one cement: 6 (six) coarse sand),complete: including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm (twenty millimeter) nominal size) upto plinth level with cement mortar 1:6 (one cement: six coarse sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification clause 1204.3.8. Granular material, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five) in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (one cement : four coarse sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Half brick masonary with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five) in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (one cement : four coarse sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing woodwork in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fastners pf required diameter and length (hold fast lugs or dash fastner shall be paid for separately) Second class deoder wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing woodwork in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc.Second class deoder, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing panelled ,glazed or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid separately, Second class teak wood in super structure for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm(one point four milimtere) in both directions with wire of dia 0.63 mm(zero point six three milimeter), for doors, windows and clerestory windows with hinges and necessary screws second class teak wood , 35 mm(thirty five milimeter) thick shutters including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing wooden plank ceiling with tongued and grooved jointing and wood screws(frame work and cover fillets to be measured and paid for separately)First class indina kail wood 20 mm (twenty milimtere) thick, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.S.grills of required pattern in frames of windows etc. With M.S flats, square or round bars etc.including priming coat with approved steel primer all complete.Fixed to steel windows by welding, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing 40x5 mm (Forty into five millimeter) flat iron hold fast 40cm. (Forty centimeter) long including fixing to frame with 10mm (Ten millimeter) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. (Thirty into ten into fifteen centimeter) 1:3:6 mix (One cement : three sand: six graded stone aggregate 20mm (Twenty millimeter) nominal size) in all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 75 mm x 60mm rounded hand rails in straight length complete in.second class deodar wood., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 18 mm (eighteen millimeter)thick, 150 mm (one hundred fifty millimeter) wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked, including top cover of 6 mm (six millimeter) commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm (twenty millimeter) diameter (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm (twenty into three millimeter) M.S. flat 10 cm (ten centimeter) long fixed to pelmet with hollock wood cleats of size 100 mm x 40mm x 40 mm (hundred into fourty into fourty millimeter) on both inner side of pelmet and rawl plugs 75 mm (seventyfive millimeter) long etc. all complete, including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

300x10 mm (Three hundred millimeter into ten millimeter)

200x10 mm (Two hundred millimeter into ten millimeter)

Providing and fixing aluminium tower bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

300x10 mm (Three hundred millimeter into ten millimeter)

200x10 mm (Two hundred millimeter into ten millimeter)

Providing and fixing aluminium handles, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour orshade, with necessary screws etc. complete, including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

125mm (One hundred twenty five millimeter)

100mm (One hundred millimeter)

Providing and fixing bright finished brass hard drawn hooks and eyes: 150mm (One hundred fifty millimeter), including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete :150 mm (One hundred fifty millimeter), including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing ISI marked oxidised M.S. single acting spring hinges with necessary screws etc.complete :125 mm (One hundred twenty five millimeter), including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing cup board shutters with 25 mm (Twenty five millimeter) thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm (twenty five millimeter) wide x 12 mm (twelve millimeter) thick with necessary screws and bright finished stainless steel piano hinges, complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. With non decorative veneering on both sides.

Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately)complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Cement concrete flooring 1:2:4 ( one cement : two sand :four graded crushed stone aggregate 20mm.(twenty millimeters) ) finished with floating coat of neat cement,including cement slurry,but excluding the cost of nosing of steps etc. 40mm.(forty millimeters) thick with 20mm (twenty millimeter) nominal size aggregate , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm (twelve millimeter) thick bed of cement Mortar 1:3 (One cement: three coarse sand) and jointing with grey cement slurry @ 3.3kg (three point three killograme) per sqm (square meter) including pointing in white cement mixed with pigment of matching shade complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Kota stone slab flooring 20 mm (Twenty millimeter) (average) thick base of cement mortar 1:4 (One cement : four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete.25 mm (Twenty five millimeter) thick. Kota stone 55×55cm (Fifty five into fifty five centimeter) minimum size having one shade only with yellow Jaisalmer marble strips as per pattern, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Kota stone slab 20 mm (Twenty millimeter) thick in risers of steps, skirting dado and pillars laid on 12 mm (Twelve millimeter) (average) thick cement mortar 1:3 (One cement :three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete. Kota stone 55×55cm (Fifty five into fifty five centimeter) minimum size having one shade only with marble strips as per pattern, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying rectified Ceramic glazed floor tiles of size 300x300 mm (three humdred into three humdred millimeter) (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm (Twenty millimeter) thick cement mortar1:4 (one Cement : four Coarse sand), Jointing with greycement slurry @ 3.3 (three point three) kg/sqm (kilogram per square meter) including pointing the joints with white cement and matching pigment etc., complete. Including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying 60mm (sixety millimeter) thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design and shape, laid in required colour and pattern over and including 50mm (fifty millimeter) compacted bed of coarse sand ,filling the joints with line sand etc. all complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 0.60mm ( Zero point six zero milimeter ) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and rubber washers complete with all accessories as required as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing ridges or hips 60 cm (sixety centimeter) overall with 0.60mm (Zero point six zero milimeter) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm (six millimeter) dia & prepainted G.I. limpet and bitumen washers complete as per HP.PWD., Specifications of 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimeter) gap for thermal expansion, (i) Single socketed pipes 110 mm (one hundred ten millimeter) diameter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110mm (one hundred ten millimeter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.S. BP Sheet 1.66 mm (one point six six millimeter) to 2 mm (two millimeter) thick in eaves board /facia/soffits /ceiling including cutting , fixing and welding to steel roof members and applying a coat of red lead primer complete,including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. (Base member of steel work shall be measured & paid separtely).

6mm (Six millimeter) Cement Plaster to ceiling. In cement mortar 1:3 (One cement : three sand) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

15mm (Fifteen millimeter) cement plaster in single coat on the rough side of single or half brick/concrete/stone walls for interior/ exterior plastering up to floor two level including arrises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (Eighty millimeter) in girth and finished even and smooth in cement mortar 1:6 (One cement: six sand) in Super-structure for all floors in all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm (zero point nine zero liter per ten square meter )over an under coat of primer applied @ 0.80 (zero point eight zero) ltr/ 10 sqm (liter per ten square meter) of approved brand and manufacture: complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Applying priming coat:With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood):complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm (zero point nine zero liter per ten square meter )over an under coat of primer applied @0.75 ltr/10sqm (zero point seven five liter per ten squaremeter) of approved brand and manufacture:complete , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 (fifty) grams/ litre :complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Wall painting with premium acrylic emulsion paint of interior grade, havimg VOC (Volatile Organic Compound) content less than 50 (fifty) grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and applying white cement based putty of average thickness 1 mm (one millimeter), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Finishing walls with water proofing cement paint of required shade :New work (Two or more coats applied @3.84 kg/10 sqm (three point eight four kilogram per ten square meter) : complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer : complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (one cement : one fine sand) including testing of joints etc. complete :100 mm (one hundred millimeter) diameter. Including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 3 (three) layer PP-R (Poly propylene Random copolymer) pipes confirming to IS: 15801 UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply, including all PP-R plain and brass threaded polypropylene random fittings, includng trenching, reffiling and testing of joints complete as per direction of Engineer-in-charge ; External work. PN-16 Pipe, 20mm OD (SDR-7.4).Including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PVC cowl ISI marked including jointing the cowl with PVC pipe with approved adhesive etc.complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

100mm (one hundred millimeter) nominal diameter.

75mm (sevety five millimeter) nomianal diameter.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (one hundred millimeter) sand cast Iron P or S trap 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever)conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass pillar taps, 32mm (thirty two millimeter) C.P.brass waste standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:-White Vitreous China Wash basin size 550x400 mm (five hundred fifty into four hundred)with a 15 mm (fifteen millimeter)CP Brass pillar taps, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 600х450 mm (six hundred into four hundred fifty millimeter)beveled edge mirror of superior glass (of approved quality) complete with 6mm (six millimeter) thick hard board groundfixed to wooden cleats with C.P. brass screws and washers complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm (six hundred fifty millimeter)long towel rail with total length of 695 mm(six hundred ninety five millimeter),78 mm (Seventy eight millimeter)wide and effective height of 88 mm(Eighty eight millimeter), weighing not less than 190 gms(One hundred ninety grams):.including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 600x120x5 mm (six hundred into one hundred twenty into five millimeter) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm (fourty millimeter) long screws, rawl plugs etc.,complete: including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm (one hundred thirty eight millimeter), breadth 102mm (one hundred two millimeter), height of 75mm (seventy five millimeter) with concealed fitting arrangements, weighing not less than 106 gms (one hundred six grams),complete: including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT 15 mm (Fifteen millimeter)Urinal spreader size95x69x100 mm(Ninety five into sixty nine into hundred millimeter) with 1/2" BSP thread and shapes,weighing not less than 60 gms.:.including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm (fifteen millimeter) nominal bore, complete: including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931, 15 mm (fifteen millimeter) nominal bore, complete: including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm (Fifteen millimeter)nominal bore.including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Range of two half stall urinals with 10 litre P.V.C. automatic flushing cistern.including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm (Forty five centimetre)length15 mm(Fifteen millimeter) nominal bore:.including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 15mm (fifteen millimeter) nominal bore, .including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Proving and fixing 3 (three) layer PP-R (Poly propylene Random copolymer) pipes confirming to IS: 15801 UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply, including all PP-R plain and brass threaded polypropylene random fittings, includng trenching, reffiling and testing of joints complete as per direction of Engineer-in-charge, PN-16 (sixteen) Pipe, 25mm (twenty five millimeter) OD (SDR-7.4).Including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PE-AL-PE composite end seal compression fitting as per IS -15450-2004 for cold water supply e.g. tee, elbow, reducers, connector couplers and clamps with jointing testing and fitting complete including ,cutting and making good the wall etc. including carriagr of material through all modes of transportation with in all leads and lifts, as per PWD specfication and as per direction of Engineer-in charge

Equal Tees, 1216 mm (one thousand two hundred sixteen millimeter) size.

Female branch Tee, 1216х1216х15 mm(one thousand two hundred sixteen into one thousand two hundred sixteen into fifteen millimter)

Female elbows 1216х15 mm (one thousand two hundred sixteen into fifteen millimter)

Female thread connecter 1216х15 mm (one thousand two hundred sixteen into fifteen millimter)

Couplers 1216 mm (one thousand two hundred sixteen millimeter)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm (hundred millimeter)inlet and 100 mm(hundred millimeter) outlet Sand cast iron S&S as per IS: 3989, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing high presure PVC spigot and socket waste and ventilating pipes (ISI) marked including fixing with approved adhesive etc.complete including carriage of material through all modes of transportion with in all leads and lifts ,aas per PWD specfication and as per direction of Engineer-in-charge

110mm (one hundred ten millimeter)

75mm (seventy five millimeter)

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3mm (three millimeter)thick bolts and nuts complete including fixing with approved adhesive etc. complete. 75mm (seventy five millimeter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PVC door bend with ovel access door insertion rubber washer 3mm (three millimeter) thick bolt and nuts ISI marked complete including fixing with approved adhesive etc. complete, 150mm (one hundred fifty millimeter) including carriage of material and through all modes of transportation with in all leads and lifts, as per PWD specfication and as per direction of Engineer -in -charge

Providing and fixing PVC collar ISI marked including fixing with approved adhesive etc. complete ,including carriage of material through all modes of transportation with in all leads and lifts ,as per direction of Engineer-in-charge

110 mm(one hundred ten millimeter) in dia.

75mm (seventy five millimeter) in dia.

Providing and fixing PVC plain double branch ISI marked including fixing with approved adhesive etc. complete ,including carriage of material through all modes of transportation with in all leads and lifts ,as per PWD specfication and as per direction of Engineer-in-charge

110 mm(one hundred ten millimeter) in dia.

75mm (seventy five millimeter) in dia.

Providing and fixing 100mm (one hundred millimeter) sand cast gully trap,complete: including carriage of material through all modes of transportation with in all leads and lifts ,as per PWD specfication and as per direction of Engineer-in-charge.

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 one cement : 4 four coarse sand) for sluice valve, with C.I. surface box 100mm (one hundred millimeter) top diameter, 160 mm (one hundred sixety millimeter) bottom diameter and 180 mm (one hundred millimeter) deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 one cement : 2 two coarse sand : 4 four graded stone aggregate 20mm (twenty millimeter) nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 one cement : 5 five fine sand : 10 ten graded stone aggregate 40 mm(fourty millimeter) nominal size) and inside plastering with cement mortar 1:3 (1 one cement : 3 three coarse sand) 12 mm (twelve millimeter) thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(nonmodular) bricks of class designation 7.5 (seven point five),complete: including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.