REPAIR TO DRAIN, PATH, FENCING, COMPOUND WALLS, GATES, RETAINING WALLS, BREAST WALL, PARAPETS ETC AT CHINDIT TOP, TENGA LEDGE, OTM ACCN NEAR DUNN BRIDGE AREA AND LOWER AND UPPER DAHUNG AREA UNDER GE 859 EWS

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving’s not exc 15 cm thickness (below or above ground level)

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for.

Demolition of Brick or stone boulder masonry laid by CM or lime mortar.

M & L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate )as in foundation bed concrete.

M&L for stone walling built in CM 1:6 in random rubble masonary, uncoursed, well bonded, solidly hearted built in retaining wall, abutment and similar works.

M & L for hand packing with broken stone/ boulderbehind backing of retaining wall,in layers etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in coping including necessary formwork complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in bond stone etc.

M&L for raised pointing to random rubble masonry , uncoursed or brought upto courses in CM 1:4.

S&F 75mm dia PVC (SWR) pipe in any length with rubber joint laid in trenches or floors.

M & L for 75mm thick, PCC 1:2:4 type B-1, (using 20 mm graded stone aggregate) as in path finishing cement concrete surface even and fair spike rolling to surface or making impression of expanded metal, whilst the concrete is green.

M & L for PCC 1:3:6 type C2, (using 40 mm graded stone aggregate) as in surface channels, drains etc.

Material and labour for providing precast cement concrete block of PCC (1:3:6) type-C1 in masonry with solid blocks, exceeding 10cm in width & set in cement mortar (1:4) complete all as specified and directed.

Taking down cement plaster on brick, concrete stone surfaces etc including raking out joints, hacking for key, scrubbing down with water etc.

M & L for 15mm thick rendering in cement mortar 1:4 on brick or concrete surfaces with cement finishing the surfaces even & fair.

M & L for PCC 1:3:6 type C2, (using 40 mm graded stone aggregate) as in parapet ,retaining wall etc

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for.

Dismantling fencing wire mesh, any type.

Excavation in post holes each n exc 0.5 cum and getting out in hard/dense soil, returning, filling in and ramming earth in layers n exc 25 cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface.

M&L for PCC (1:4:8) type D-2 (using 40mm graded aggregate) as in foundation filling and mass concrete etc all as specified & directed.

M&L for providing RCC (1:2:4), type B-1 (using 20 mm graded crushed stone aggregate) as in precast posts, fencing posts, straining or terminal posts, struts etc. for fencing average sectional area exc 100 sq cm and n exc 250 sq cm, all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, all as specified and directed.

M&L for mild steel TMT bars 6 mm dia and over in stirrups, spaces and binders.

S&F MS Screw bolts 12 mm dia (machine made) with hexagonal or square heads at one end and screwed the other, embeded in RCC post, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10 cm but n. exc 15 cm long.

S&F Mild Steel Flats 40 x 6 mm thick in wind ties for roof inclduding securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc conforming to Fe-290 Gde E-165.

Supply only MS galvanised chain link fencing any size or type.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards rails, straining bolts, etc, including provision of binding wire.

S&F 10 mm dia bars as stiffening member in fencing including securing the fencing.

M&L for applying two coat of synthetic enamal paint over a coat of red oxide primer on steel surfaces of any descripition over 10 cm width or girth etc. complete.

S&F galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc as directed.

M&L for three coats of white wash including preparation of new concrete surfaces of fencing posts etc all as specified.

M & L for screed bed or bedding layers 15 mm thick in CM 1:4 finished rough for laying floor tiles.

M&L for Chequered cement concrete tiles 20cmx20cmx25cm thick with gre cement and pigment, set jointed and pointed in neat cement slurry in floors.

M&L for Providing, cement concrete type B1 (1:2:4) using 20 mm graded aggregate in roof kerbs or mud stops, rounded or chamfered on edges including necessary formwork complete all as specified nad directed.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel')

S&F plain, black, mild steel sheet(tk 0.8 mm) in wall cladding, ridges,hgips, valley gutters, drip and straight flashing etc.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exc 4 Sqm.

S&F PVC Modular speed breaker with all nacessary fitting complete all as specified and directed.

S&F retro reflective signage MANDATORY/REGULATORY SIGNS, CAUTIONARY/WARNING SIGNS, INFORMATORY/GUIDE SIGNS as per IRC : 67 made out of high intensity presmatic (HIP) polycarbonate retro reflective sheet having polycarbonate limit as 30% to 50% by weigth and conforming to ASTM 4596 type IV standard. The retro reflective film to be pasted on front side or both side 2mm thick aluminium sheet conforming to IS-737 standard and back side of the board will be having two coats of grey or black synthetic enamel paint complete all as specified and as directed. Make : CMS/3M as approved by GE.

M/S R N ENTERPRISES

M/S ASHOK CONSTRUCTION

PT constuction

M/S MURPHEW ENTERPRISES

M/S LARZAWANGPU AGENCIES

M/S DK TRADERS

D.P. Traders