PROVN OF STORAGE SHED IN AM AREA UNDER AGE BR I AND CERTAIN SPECIAL REPAIRS UNDER GE (WEST) FEROZEPUR CANTT

Amount

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed.

M&L for 50 mm thick, Cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in plinth oprotection, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 40 mm thick, Cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in floor topping, surfaces finished even and smooth without using extra cement complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises.

S&F Vitrified ceramic tiles 10mm thick (Square/rectangular)polished area of each tiles exc 0.36Sqm and not exceeding 0.42Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured (Light Shade)cement to match over 20 mm thick screed bed or bedding layer of cement mortar(1:6) for laying floor finishes.

M&L for light shade Vitrified tile 10mm thick polished, area of tile n exc.0.36 sqm as in Skirting set and jointed in cement slurry over and including 10mm thick screed in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

Demolition of Stone slabs and tiles laid bedded pointed in mortar of any description or thickness in floors, aprons etc.

M&L Machine cut kota stone slab flooring 20-25mm thick over 20 mm cement screed base CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishing and rounded or chamfered for nosing complete all as per specified and directed.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10 mm thick rendering (1:4) and jointed with ditto as per item no 8 here-in-before.

M&L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35Grade including laying of sand cushioning, etc, complete all as specified and as directed. Note :- Sand will be measured and paid seperately

Dismantling brick work built in cement mortar of any specification and in any position complete all as specified and directed.

M&L Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and directed.

All as per item no. 12 here-in-before but using old bricks retrieved from item no 11 demolition including cleaning and removal of mortar from old bricks.

M & L brick work with sub class B bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm complete all as specified and directed.

All as per item No 15 here-in-before but size exceeding 1.5 Sqm and not exceeding 4 Sqm each.

S&F factory made Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and directed.

All as per item above 17 here-in-before but size 125x60mm with double rebate.

S&F 35mm thick factory made second class hard wood plain framed panelled shutters (any number of panels ), with panels of timber flat on both sides (feather edge), or of veneered particle board medium density wood wood particle board with commericial face veneers ,size of member of shutters as specified in SSRpart-1section 8.24 suplied and fitted to chaukhat complete all as specified and directed.

S&F 30 mm thick, factory made 2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified and directed.

S&F Factory made box type steel window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed.

S&F Factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified

S&F Factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified

S&F Mild steel framed work of as in grills/guard bars shouldered with steel window/ ventilator frames complete all as specified.

S&F mild steel pressed handle ,oval type ,125 mm stoved enameled black and fixed with steel screw complete all as specified

S&F MS barrel tower bolts stone enamelled black with bright bolt,200mm length of bolt.

S & F 300mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including bolts and nuts complete all as specified.

S&F butt hinges 100mm size exturded Alu. alloy with galvanised mild steel hinge pin anodised and fixed type B21 Specified and directed.

M&L 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified.

S & F Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified

M&L Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over red lead primed steel surfaces complete all as specified.

M&L Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L rendering 15 mm thick in CM (1:3) on faire faces of brick work or concrete surfaces finished even and smooth with using extra cement,with water proofing compound @3% by weight of cement or as per manufacturer instructions will be on surface to have a smooth surface for laying of water proofing membrane. Note: WPC shall be measured and paid separately

Supply only water proofing compound.

M&L Tack coat of industrial bitumen 85/25 @ 1.20 Kilogram per square metre over a coat of bitumen primer @ 1.2 kg per square metre including preparation of roof surfaces complete all as specified and directed.

M&L For APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) Laid on primed surface by forced application including bitumen primer complete all as specified.→

M& L for App Membrane to be finished with two coat of solar reflactive bituminous aluminium Paint @ 0.1 kg per sqm

M & L for Cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in coping, benching, roof kerbs or mud stops, rounded or chamfered on edges including necessary form work complete all as specified.

M &L for removing loose and broken concrete by chiseling/picking etc upto a depth of 20-40 mm from floor/roof slab and similar structural members cutting edges cleaning the dismantled portion with wire brush etc to remove dust, dirt and other foreign particles etc and washing with clean water with pressure and removal of debrises to a distance n exc 50m complete all as specified and directed by Engineer in Charge. Note: Including necessary scaffolding etc

M&L for applying one coat of anti corrosive primer as manufacturers instruction to exposed old and new reinforcement to the full circumferences and length of bars to form unbroken 40 micron thick film in the area prepared vide above item no. 39 here-in-before complete all as specified and directed. Make : Forsoc(Nitozine Primer), Sika or equivalent

M&L for applying one coat epoxy bonding agent as per manufacturers instruction to old concrete surface in the area prepared vide above item no. 39 complete all as specified and directed, in surfaces of columns, beams, and similar structural members including use of waste of water tight form work to facilitate pouring of microfibre all as specified and directed.

M&L Hard Drown steel wire fabric cut to length , bent to shape required and tying with including mild steel wire anealed not less than 0.9 mm in dia supplied and fixed in reinforcement

M&L for application of 20-40 mm thick high build polymer modified to ceiling with cement mortar Plaster (1:3) with SBR @ 4 ltr per bag of cement applied as per manufacturer's instrutions.as in complete all as specified and directed.

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Material and labour rendering 15 mm thick cement plaster in CM 1:4 on other than fair faces of brick/concrete work surfaces compound finished fair and even all as as specified and directed.

Material and labour rendering 10mm thick cement plaster in CM 1:6 on fair faces of brick or concrete surfasces finished even and smooth (without using extra cement ) all as specified and directed.

M&L Rendering 5mm thick in cement mortar (1:3) on any face of brick walls or conrete surfaces, surfaces finished even and smooth without using extra cement, in ceiling, soffits of chajja or similar location etc complete all as specified & directred.

M & L for rendering 12 mm thick on wall in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement and Preparation of new plaster surfaces of wall and applying three coat of white wash complete all as specified and as directed by Engr -in- charge .(Make -BERGER, ASIAN PAINT OR NEROLAC)

M&L for rendering 15 mm thick in cement mortar 1:4 on external fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) including and preparation of new plaster surfaces of wall and applying two coats cement based paint over one coat alkali resistant priming paint complete all as specified and as directed.

M&L Preparation of new plastered surfaces and applying three coats of white wash on walls complete all as specified and directed

M&LPreparation of new plastered surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L White wash in three coats on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L for complete Removal of existing treatment of walls and apply two coats of white wash complete all as specified and directed.

M&L of for washing rubbing down and stopping of cement base painted surfaces and applying one coat of cement based paint on wall surfaces including proper curing all as specified and directed.

M & L for preparing of old decorated surfaces (plastered or un-plastered) by brooming down and applying one coat of white wash to ceiling.

M&LCement concrete (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection, 75mm thick, surfaces finished even and smooth without using extra cement complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed to walls

Dismantling of wall and ceiling boards (Fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

S & F in repair to Hollow PVC wall lining consisting of 5mm thick single side prelam PVC sheet instead of plain colour sheet inclusive of solvent cement and fixing on PVC frame as per specified in MES schedule part-I & II complete all as specified and directed.

M&L for Site Clearance getting out in soft/loose soil.

M&L for excavation in trenches n. exc 1.5mtr wide and n. exc 1.5mtr deepth for foundation etc or for shaftswells cesspits manholes pier holes etc n exe 10 sqm on plan and n exe 1.5 mte in depth and getting out in soft/loose soil.

M&L for PCC 1:4:8 type D2 using 40mm graded stone agregate as in foundation filling and mass concrete all as specified.

M&L for RCC M-25 design mix (20mm graded aggregate) in foundation,footing, plinth beam,bases for columns etc

Use and waste of formwork to sides of concrete foundation ,footing,base of column ,raft beams , sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter to rough finish surface of concrete flat.

M&L for RCC M-25 design mix (20mm graded aggregate) in Columns, pillars, piers and similar works

Use and waste of formwork to sides of posts, struts, piers, columns and similar work vertical or to batter to rough finish surface of concrete flat.

M&L for RCC M-25 design mix (20mm graded aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span and similar work

Use and waste of formwork to sides and soffits of floor or roof beams, beam similar work to rough finish surface of concrete flat.

M&L for returning filling in including spreading levelling watering and well ramming in layers not exe 25 cm for soft lose soil.

M&L removing excavated soil n exe 50 mtr and deposting where directed at alevel not exe 1.5 mtr above the starting point.

M&L Fine aggregate (sand) filling in floors or in foundation or cable protection including Spreading leveling watering & well ramming in layers not exc. 25 cm thick of soil complete all as specified and directed.

S&F Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L TMT mild steel bars 5 to 10mm dia,as in stirrups cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for broken bricks hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L PCC 1:4:8 type D-2 using 4 mm graded stone agg as in sub base, sub floor 75 mm thick complete all as specified and directed.

M&L for 150 mm thick PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as alternative way in floor complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240; purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

M&L for steel rolling shutters, gear operated type with bevel gear box and crank handle with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer,erected in position as indicated, complete all as specified and directed.

M&L Ball bearing for rolling shutters

M&L for safety lever locks mild steel with 4 levers for rolling shutters

Taking down carefully copper /aluminium point wiring (light, fan, socket or power ) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M &L Point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor, multi stranded of size 1.5 sqmm, single core, in and including rigid non-metallic PVC conealed conduit, with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green PVC insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) One light/fan/Bell Point controlled by one single pole one way switch.

(b) One 5 amp socket outlet on the same board controlled by one single pole one way switch

(c) One 5 amps socket outlet independent controlled by one single pole 5 Amp switch.

All as per Item No 84 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing complete.

Supply & Fixing Switch piano flush type single pole one way 5/6 Amp complete all as directed.

Supply & Fixing Switch piano flush type 15 amps, single pole one way duly ISI marked.

Supply & Fixing Socket outlet 2 in one, 5/6 Amps flush type ISI marked.

Supply & Fixing Socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type ISI marked.

Supply & Fixing bell push flush type 5 Amps duly ISI marked.

Supply & Fixing ceiling rose, PVC/Polycarbonate,isolated three terminals.

Supply & Fixing Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings including 10W LED Bulb omplete all as specified and directed.

Supply & Fixing bell ding dong type AC 230 Volt single pole.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm

Supply and fix exhaust fan, steel body AC single phase 230V of size 300 mm sweep with, blades and frame and louvers complete all as specified and directed.

S&F LED tube light fitting 1 X18/20 W decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

S&F LED tube light fitting 1 X 18 W decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Cat Part No LHEXBLP7UN1W018 Make - Havells or Techno Commercially equivalent in approved Makes.

Supply & Fix in repair LED tube light fitting 9 watts batten type fixed on wall/ ceiling etc. including connecting up with twin core twisted flexible copper conductor cable with suitable size all as specified and directed.

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with highefficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. Cat No.LCTLRN-36-FO-CDL of Crompton or Techno Commercially equivalent in approved Makes.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. complete all as specified and directed.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type) fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified.

All as per Item No 105 above but SPN DB's 4 way.

All as per Item No 105 above but DB's 2 way, single door.

Supply & Fixing MCCB 100 Amps, 415 volts, 16 KA, 4 Pole complete all as specified.

Supply & Fixing MCB, Single pole 240 V, 6 - 32 Amps 10 KA 'B' Series.

Supply & Fixing MCB, Single Pole and neutral 240 V, 32 Amps 10 KA 'B' series.

Supply and fix modular type AC motor starter 25 Amps 230 volts Two module complete all as specified and directed. Make : Havells Cat Part No AHFSMXW251 or equivqlent

Supply and fix modular type 10 A / 25 A shuttered socket, 230 volts Two module complete all as specified and directed. Make : Havells Cat Part No AHFKCXW253 or equivqlent

Supply Installation commissioning & testing of water heater storage type electric capacity 25 ltrs, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. Electric Storage water Heater Monza DX Cat Part No GHWAMGTWH025 of Havells or equivalent in any other make.

Supply & Fix in repair sub main wiring of 4 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor with earth wire of 4.0 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor including PVC conduit pipe 25 mm dia all as specified and directed. Note: Two run of single core 4 sqmm cable and one run single core 4.0 sqmm cable for earth wire and including conduit pipe 25 mm dia shall measured as one length).

M & L for sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2 x 6 sqmm drawn through in and including PVC Concealed with 1 x 6 sqmm PVC insulated copper conductor single core for continuous earthing complete including PVC conduit 25 mm dia ( Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated copper conductor single core,one run of PVC conduit shall be measured as single run)

Supply, laying and testing cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 50 sqmm 3.5 core complete all as specified and direced.

Supply, laying , jointing and testing of cable XLPE insulated, screened, PVC bedded ,galvanized steel strip or wire armoured heavy duty electric cable with multistranded aluminium conductor, 1100 volts grade, laid in trenches or duct or passing through pipe or fixed to poles walls of size 25 Sqmm 4 core confirming to IS : 7098-1985 laid in trenches or passing through pipes/ducts or fixed to walls/poles complete all as specified and directed.

Supply, laying , jointing and testing of cable XLPE insulated, screened, PVC bedded ,galvanized steel strip or wire armoured heavy duty electric cable with multistranded aluminium conductor, 1100 volts grade, laid in trenches or duct or passing through pipe or fixed to poles walls of size 10 Sqmm 2 core confirming to IS : 7098-1985 laid in trenches or passing through pipes/ducts or fixed to walls/poles complete all as specified and directed.

M & L Bricks (Size 23x11.5x7.5 cm) common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry width wise acrose the line of cable in trenches for protection of UG cable complete all as specified and direced.

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009)

Mild steel galvanised iron pipe light grade (ISI marked) 40mm bore for passing of earth lead laid in trenches fixed to walls laid under floors, roads including all fittings i.e MS clamps nuts & bolts etc as required all as specified and directed.

M/s Sarup Singh

M/s Surjit Singh and bros

M/s Harkesh Kumar Bansal

Sethi and Company

Dee Kay EnterPrises

HARBHAJAN SINGH KHARBANDA

VK ENTERPRISES