GE 861EWS-37/2022-2023

Amount

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed.

Demolition of brick work or stone boulder masonry built in cement mortar including all arches quoins etc but excluding ashlar facing, dressed stone work & precast concrete articles etc complete all as specificed and directed.

Demolition of cement concrete (unreinforced) in ground floors & paving n.exc 15 cm thick (below or above ground level) complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm complete all as specified and directed.

Taking down chowkat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each complete all as specified and directed.

Dismantling of timber scantling under 40 Sqcm, fixed in any position in fillet rails, posts rafters purlin etc complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, complete all as specified and directed.

Demolition wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets & snap grid frame etc, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar, complete all as spcified and directed..

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and as directed.

Precast cement concrete type C-1(using 16mm graded crushed stone aggregate) hollow block masonry with hollow blocks exceeding 10cm in width and setting in mortar 1:6, complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan, to any radius, in half brick thick wall, using old size brick, built in cement mortar 1:6, complete all as specified and directed.

10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

15mm thick rendering on fair faces of brick or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Joint free non-skid dark coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Glazed ceramic coloured tiles 450mm x 350mm x 7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Chequered coloured cement concrete tiles of size 200 x 200 x 25mm thick, glossy finished, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

25mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crused stone aggregate) as in floors to recieve floor finishes, complete all as specified.

75mm thick PCC 1:3:6 Type C-2 (40 mm graded stone aggregate) as in sub-floor, sub-base, floor and pavings, etc., complete all as specified and directed.

Plain cement concrete M-10, 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 50mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

Rolled mild steel in roof trusses (framed),trussed ,purlins,crane girders,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W (Gde-E-250) quality-A, complete all as specified and directed..

MS TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed.

35mm thick, 2nd class softwood factory made, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed.

35mm thick, 2nd class softwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

30mm thick, 2nd class softwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (b) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed, worught, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

GI frame work of size 605mmx605mm for seamless ceiling comprising of GI perimeter channnel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre., complete all as specified and directed.

10mm thick PVC insulation panels with EPS stuck to 1mm thick plain PVC sheet suitably placed in exiting/new false celing grid made of aluminim/GI/MS as per specification and drawing, complete all as specified and directed.

6mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.

6mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in walls with nails to timber frame, complete all as specified and directed.

2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm, complete all as specified and directed.

2nd class softwood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area exc 3 Sqcm but n exc 6 Sqcm complete all as specified and directed.

2nd class softwood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area not exc 3 Sqcm, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plaind steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

300mm size aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

150mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

100mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, extruded aluminium alloy handles, fabricated type, anodised, all as specified and directed.

100mm long, extruded aluminium alloy handles, fabricated type, anodised, all as specified and directed.

100mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

75mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

140mm long, floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F in repair 20mm dia decorative brass chromium plated curtain railfixed to decorative brass bulb type brackets, complete all as specified & directed.

S & F in repair 300mm long mild steel ordinary rat tail rod pattern, springs including roller and roller plate fixed to wooden chowkhat, complete all as specified and directed.

3mm thick figured glass pin headed type and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified and directed.

Steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantlling of existing tank, complete all as specified and directed.

Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantlling of existing tank, complete all as specified and directed.

S&F in repairs vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but including cast iron 'P' trap, jointing to flush pipe, inject connection to trap, antisyphonage etc. complete and making good to floor in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (semi pedestal) (anglo indian), white & making good to floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and as directed.

S&F in repairs single lever wall mixer (3 in1) exposed shower pipe, spout fitted with overhead rain shower, telephonic hand shower and 1.50 mtr flexible stainless steel hose fixed with hot and cold water mixer including all fittings, complete all as specified and as directed.

S&F in repairs central hole basin mixer with 450mm braided connection pipe, complete all as specified and as directed.

S&F in repairs health faucet brass body with wall hook and 1.00 mtr SS braided rubber hose pipe, complete all as specified and as directed.

S&F in repairs towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats, complete all as specified and as directed.

S&F in repairs stainless steel soap dish, complete all as specified and as directed.

S&F in repairs toilet paper holder with flap guard, complete all as specified and as directed.

S&F in repairs fancy type corner glass shelf of size 300mm x 300mm x 5.5mm thick glass with CP Railing, complete all as specified and as directed.

S & F in repair for 125mm size brass chromium plated shower rose with or without swivel joints, any size including fixing to steel pipe of 15mm dia or union, complete all as specified.

S&F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, flushing pipe, handle including brackets, complete all as specified and directed.

S&F in repair vitreous china, wash hand basin, flat back of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, including 32mm dia brass chromium plated waste fitting with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.

Viterous china, wash hand basin, (white) of size 550 mm x 400 mm including PVC waste coupling 32 mm dia with long screwed shank and fly nuts, PVC medium grade 32 mm dia waste pipe, chain and plug, porcelain stopper, PVC connection 15 mm dia, 450 mm long with PTMT nuts and washers at both ends and 15mm bore stop valves, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union (fixed in repair) , complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S&F in repair vitreous china bowl urinal flat back, size 465 x 355 x 265 mm, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; with grating and union for discharge pipe, complete all as specified and directed.

S&F in repair 15mm bore bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S&F in repair 15mm bore bib tap with wall flange, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S & F in repair 15mm dia pillar taps, fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot' and 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15mm bore stop/angle valves, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repairs 15mm bore stop valves, fancy type, chromium plated with long long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges, complete all as specified and directed.

110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

110mm bore dia PVC (SWR) bends, complete all as specified and directed.

75mm bore dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.

110mm bore pipe PVC (SWR) vent cowl and fixed, complete all as specified and directed.

110mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed.

S&F in repairs 75mm dia outlet PVC (SWR) multi floor trap with openable grating including jointing with solvent cement, complete all as specified and directed.

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation, laying of pipes/cables etc or for shaft wells, cesspits manholes pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in any type of soil, complete all as specified and directed.

Returning filling in (soil) including spreading, levelling , watering and well ramming in layers n exc 25cm thick, complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 mtr and depositing where directed at a level n exc 1.5 mtr above the starting point, complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete, complete all as specified.

Precast cement concrete type 1: 2: 4, type-B1 (20 mm graded aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set and jointed in CM 1:4, complete all as specified and directed.

Cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed.

PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in surface channel and drains, complete all as specified and directed.

Concrete bed to drain pipes 150mm bore including packing under,and haunching against the sides of pipes after they are laid and treated in cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate, complete all as specified and directed.

150mm bore reinforced concrete pipes, class NP2, laid and jointed complete with collars, complete all as specified and directed.

Construction of septic tanks, exc, in ordinary soil, foundation In PCC 1:2:4, brick work in CM 1:4, RCC Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fiber reinforced cover with angle iron frame Vent shaft and sludge chambers etc., complete for 100 users complete all as specified and directed. Drg No CESZ/TD-01/2015 Sheet 1/3, 2/3.

Construction of soakage well for users, excavation in ordinary soil, foundation PCC 1:3:6 wells of honey combed and solid in M-25 concrete, including intercepting chamber chamber screen chamber, brick work CM 1: 4, RCC cover slab in M-25/ RR masonry filling with brick bats, complete of size 1.80m dia 3.0m deep as shown in drg complete all as specified and directed. Drg No CESZ/TD-01/2015 Sheet 3/3.

Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed.

Complete removal of existing treatment of walls & applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed.

Preparation of new plastered surfaces of wall to receive 3mm thick wall care putty and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

Complete removal of existing treatment of walls and applying two coats of oil bound distemper over a coat of priming coat and wall care putty, complete all as specifed and directed.

Preparation of old painted wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint to match the existing surface, complete all as specified and directed.

Preparation of new or previously untreated steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old painted steel surface of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash,complete all as specified and directed.

Complete removal of existing treatment of wall and applying three coats of white wash, complete all as specifed and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including unscrewing from board fitting and fixture such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody for reuse if serviceable or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and including PVC casing and capping/Conduit medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size or PVC Gang Box with 3 mm thick plastic laminated sheet cover of adequate size for one light point/fan point controlled by one switch and making good disturbed surfaces with CM (1:3) to match with the existing surface, complete all as specified and directed.

All as per srl item No-111 here in above but for one 3 pin 5A socket outlet independent controlled by one switch, complete all as specified and directed.

All as per srl item No-111 here in above but for one 5A socket outlet on the same board controlled by one switch, complete all as specified and directed.

All as per serial item No 111 here-in-before but for 3 pin 15 Amps socket outlet independent board with 2.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead, complete all as specified and directed.

Switch piano flush button types 6 Amp, single pole, one way complete all as specified and directed.

Switch socket combination 2 in 1, 3 pin, 6 Amp flush type, universal, complete all as specified and directed.

Modular one way switch 6 Amp, 1 module, complete all as specified and directed.

Modular one way switch 16A, 1 module, complete all as specified & directed.

Modular socket outlet, 6A-2/3 pin combined 2 module, 230 volts complete all as specified and directed.

Modular socket outlet, 6A/16A-2/3 pin combined 2 module, 230 volts complete all as specified & directed.

Modular fan step regulator, 120W - 2 module, complete all as specified & directed.

Modular white cover plate with frame, 2 module, complete all as specified and directed.

Modular white cover plate with frame, 3 module, complete all as specified and directed.

Modular white cover plate with frame, 4 module, complete all as specified and directed.

Modular white cover plate with frame, 6 module, complete all as specified and directed.

Modular white cover plate with frame, 8 module, complete all as specified and directed.

Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular suitable for batten fittings, complete all as specified and directed.

Ceiling rose 3 terminal bakelite 65mm x50mm surface type, PVC/ Polycarbonate, isolated body, complete all as specified and directed.

S & F in repair LED lamp 10 W, complete all as specified and directed.

Supply, installation, testing and commissioning of decorative ultra slim linear LED in replacement of 20 Watt , 4' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack including LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube, complete all as specified and directed.

LED fitting Square/round shape 12 watt 220 volts AC, white/warm recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

35 Watt LED street light fitting 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including taking down all unsv, complete all as specified and as directed.

Supply & fixing in repair MCB Distribution board , 240 volts single pole and neutral , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 8 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

Supply & fixing in repair MCB Distribution board , 240 volts single pole and neutral , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 4 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

Supply & fixing in repair MCB distribution board , 415 volts TPN, vertical type double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 4 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

MCB, SP, AC, 240 volts "B" series capacity of 06 to 32 Amps, 10kA and making connections, complete all as specified & directed.

MCB, SPN, AC, 240 volts "B" series capacity of 32 Amps, 10kA and making connections, complete all as specified & directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. NOTE :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by (-) 13.50%. (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300mm, including necessary work in wall/sheet, including connection cable of suitable size, nut bolt and other fixing material including taking down old unsv, complete all as specified and directed.

Sub main wiring with two single core PVC insulated flexible copper conductor cable of size 6 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 6 sqmm as earth lead in & including PVC casing capping medium grade 2mm thickness ISI marked incl taking down old unsv, complete all as required at site or directed.

S&F in repair 1100 volt grade heavy duty XLPE cable with PVC insulated aluminium conductor served with inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 35 sqmm nominal cross section 3.50 core laid in trenches, fixed to pole or passing through pipes including all necessary clamps, nuts, bolts washers complete all as specified and directed. Note- Earth work and protection work shall be measured and paid for separately under respective items of BOQ.

Sand cushioning to cable with dry fine sand in trenches 8 cm below the cable and 15 cm above the cable after laying, complete all as specified and directed.

Bricks laid in trenches flat with width equal to length of brick for cable protection well burnt sub class 'B' laid across the cable complete all ad specified.

Supply and laying in repairs 50mm dia GI tubing light grade with all fitting laid in trenches or fixed on wall or along pole complete for protection of electric cable/strip, complete all as specified and directed.

MCCB 4 pole, 415 volts adjustable type, 63 Amps with breaking capacity 25 KA complete all as specified and directed.

Steel water tubing, 25mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, laid in trenches, including taking out old one complete all as specified and directed.

Supply, fixing, jointing and testing, 25mm bore gun metal globe/gate valve with iron wheel head, both ends screwed for iron pipe including taking down of old one complete all as specified and directed.

Cutting of the existing 50mm/80mm bore CI/GI pipe line including run lead joints of suitable size with necessary fittings, complete all as specified and directed.

Supply and fixing in repair 1100 volts grade heavy duty cable PVC insulated copper conductor (Solid ) of size 6 Sqmm 2 core served with inner sheathing of PVC tape and overall PVC sheathed in service connections, complete all as specified and directed.

M/S HAMID & CO

JANDOO AND CO.