RENOVATION WORKS AT HEAD OFFICE OF HSPCB, C-11, SECTOR-6, PANCHKULA, HARYANA

3 Grand Total inclusive of GST ₹ 1,02,10,587.00

Providing and laying water proofing treatment to vertical and horizontal surfaces of

depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of

applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound

conforming to IS 2645 in recommended proportions including rounding off junction

of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1

cement : 3 coarse sand) mixed with water proofing compound in recommended

22.3 proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd 153.2582 Sqm 774.25 1,18,660.16

course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet

should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying flamed finish Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick

11.55 base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement

slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or

Total Cost of water Proofing and flooring works (4) 5,12,325.00

5 Replacing of all toilet fixtures including changing of existing pipes.

Providing and fixing white vitreous china extended wall mounting water closet of size

780x370x690 mm of approved shape including providing & fixing white vitreous

china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4

litre/ 8 litres),including seat cover, and cistern fittings, nuts, bolts and gasket etc

Providing and fixing stone slab with table rubbed, edges rounded and polished, of

size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of

appropriate width with chase cutter and embedding the stone in the chase with

8.10 epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and

finished smooth.

8.10.2 Granite Stone of approved shade 7.40 Sqm 3,542.85 26,214.61

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole

basin mixer of approved quality and make, including painting of fittings and brackets,

cutting and making good the walls wherever required:-

White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single

hole basin mixer

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved

quality) complete with 6 mm thick hard board ground fixed to wooden cleats with

C.P. brass screws and washers complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste

fittings complete.

17.28.2 Flexible pipe

17.34 Providing and fixing toilet paper holder : -

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112

mm distance from wall of standard shape with bracket of the same materials with

17.71 snap fittings of approved quality and colour, weighing not less than 105 gms. 6 Each 146.30 877.80

Providing and fixing CP Brass 32mm size bottle trap of approved quality & make and

as per the direction of engineer in charge.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide

with minimum distances of 37 mm from wall face with concealed fittings

arrangement of approved quality and colour, weighing not less than 88 gms.

Providing ,Fixing of straight / offset type flexible single body push fit type WC pan

connector of with integral single mould sealing fins made of flexible EVA body to be

MR fixed with manufacture supplied grease, including rubber bush / adaptor for use with 12 Each 900.00 10,800.00

C.I pipe as supplied with the pan connector.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube upto 1meter long with

17.16a S.S. Triangular plate to european type W.C. Of approved quality and make as 12 Each 299.35 3,592.20

approved by engineer in charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of

18.53.1 approved quality conforming to IS:8931 15mm nominal bore 20.00 Each 500.35 10,007.00

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm

18.21.2.1 length , 15 mm nominal bore 25.00 Each 85.20 2,130.00

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth

18.65 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 12.00 Each 96.75 1,161.00

Supply,Installation, testing and commissioning of Water Heater complete with heavy

gauge hot and cold water flexible pipe connections, Nano polymer coated tank, 8 bar

MR pressure ,of approved make complete with all necessary material as directed by

Engineer - in - Charge.

15-Litre Storage capacity 2 Each 15,000.00 30,000.00

Providing & Fixing of Grab bar 600 mm of non slipping grip as per standard

specification of use in disabled toilet complete with brackets suitable for wall

installation as per approved sample complete in all respect.

Digitally signed by SANJAY

Estimate for Toilets Renovation work for M/s. Haryana State Pollution Control Board(HSPCB)

SI.No Description Qty Units Rate (Rs) Total (Rs)

Providing and fixing of Infrared sensor controlled tap Battery operation with external

battery compartment and 4x AA alkaline batteries including flexible hoses G 3/8 int.

thread x 450 mm with prefilter and flow regulator ; flow volume: max. 3.8 l/min

MR independent of pressure ; can be adjusted to 1.33 lpm (For LEED) with additional 12 Each 22,000.00 2,64,000.00

areator 28 931 00 99 ; flow pressure: 0,5 - 5 bar ,max. resting pressure 8 bar (Model

no. of 02 172 06 99 of Schell )

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

18.8 pipes & fittings with one step CPVC solvent cement and the cost of cutting chases

and making good the same including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

18.8.1 15 mm nominal dia Pipes 10.00 Mtr. 441.15 4412

18.8.2 20 mm nominal dia Pipes 15.00 Mtr. 513.75 7706

18.8.3 25 mm nominal dia Pipes 15.00 Mtr. 626.05 9391

18.8.4 32 mm nominal dia Pipes 20.00 Mtr. 712.75 14255

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC

pipes for soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring

joints, including all neccessary specials and fittings (confirming to IS:14735) i.e.

bends, tees, junctions (with or without doors), reducers, WC connectors, couplers,

expansion joints / bellows, cowels, clamps, rubber rings, clean outs etc. fixing at wall/

ceiling/ floor level supported by clamp & hangers etc. in concealed / inside duct /

under floor & basement ceiling / external work etc. including chase cutting as

required, excavation and back filling in all kind of soils, suspended from floor under

false ceiling or embedding the pipes laid under floors / building in 75 mm. alround

1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) including cost of shuttering for proper completion of the work,

breaking and making good the walls and floors etc. after pipes have been duly laid

and tested. The rubber ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers

etc on 50x50x5 mm slotted angle. The cost will include all support arrangements. The

work includes commissioning of all pipes lines as per drawings and specifications and

as directed by engg-in-charge at site.

110 mm dia (Wall Thickness - 3.2 to 3.8 mm) 50 Mtr. 600.00 30,000.00

75 mm dia (Wall Thickness - 3.2 to 3.8 mm) 50 Mtr. 460.00 23,000.00

Providing and fixing PP white Trap with minimum 50mm water seal with rubber seal

MR on inlet to push fit hopper for indirect waste connections. -

110 mm inlet & 110 mm outlet Long ht 10 Nos 1,505.00 15,050.00

Providing and fixing floor drain (FD) with 50mm outlet and 100 mm inlet having

19mm seal for indirect floor drain (FD).

Providing and fixing Multi Trap (MT) with 50mm outlet and 100 mm inlet having

19mm seal for indirect Multi Trap (MT).

Providing, fixing, testing and commissioning of pipe inlet fittings by fixing Tee 110

x50/110 x75 mm (as required) fixed on 'P' traps for connecting fixture drains/

MR extension pices in PP including fixing and sealing inlet joint with drip seal / Pipe seal 10 Nos 850.00 8,500.00

joint as required complete.

Total Cost of Toilet Accessories including piping work (5) 8,12,025.00

Electrical work includes replacing of electrical wires, Switch sockets, LED lights etc.

and wood work including doors, window etc as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR

1.7 PVC insulated copper conductor, single core cable in surface/ recessed steel conduit

1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 50.00 meter ₹ 428.00 21,400.00

Supplying and fixing of following sizes of medium class PVC conduit along with

accessories in surface/recess including painting in case of surface conduit, or cutting

the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate

1.24 & switch box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet 20.00 Each ₹ 156.00 3,120.00

1.24.5 6 pin 15/16 amp socket outlet 20.00 Each ₹ 197.00 3,940.00

Supplying and fixing modular blanking plate on the existing modular plate & switch

box excluding modular plate as required.

Supplying and fixing following size/module, GI box along with Modular base & cover

1.27 plate on existing modular metal boxes etc. as required.

Digitally signed by SANJAY

Estimate for Toilets Renovation work for M/s. Haryana State Pollution Control Board(HSPCB)

SI.No Description Qty Units Rate (Rs) Total (Rs)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB

distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar,

2.3 neutral bus bar, earth bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, double pole, (single phase and neutral), 240

volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30

2.14 milliamperes in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature

circuit breaker suitable for inductive load of following poles in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

2.10.1 Single pole 70 Each 256 17,920.00

Supply, Installation, Testing and Commissioing of Recessed downlightwith HPE (High-

Performance Efficiency) with LED (Light Emitting Diode), system power: 12 W,

Luminous flux of luminaire 1320 lm, 110 LM/W system efficacy, Colour temperature

of 4000 K, Neutral white, CRI > 80, 230V constant current driver, 70% of luminous

flux after 50,000 operating hours; energy-efficient LEDs, direct light emission,

housing in die-cast aluminium, Polyester powder white coloured coat applied over a Each ₹ 2,100.00 1,30,200.00

5-stage pre-treatment trim, prismatic diffuser for homogenous light distribution,

ZHLS (ZERO HALOGEN LOW SMOKE) wiring, Electronic control gear,

Protection class II, IP 40,

Providing wood work in frames of doors, windows, clerestory windows and other

frames, wrought framed and fixed in position with hold fast lugs or with dash

fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood 0.25 Cum 131576.95 32,894.24

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I)

non-decorative type, core of block board construction with frame of 1st class hard

9.21 wood and well matched commercial 3 ply veneering with vertical grains or cross

bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth

9.23 on all edges of flush door shutters (over all area of door shutter to be measured). 10 Sqm 401.40 4,014.00

Providing and Fixing ESDH 1236-22X922 mm Dtype Handle for wooden doors

Material : Stainless Steel. Finish : Satin Stainless Steel (SSS). of approved make and

model all complete as per the direction of Engineer-in-charge.

Providing and Fixing EMB 245 SS Mortise Lock Body SB/TB for door thickness 25-50

MR mm for wooden doors of approved make and model all complete as per the 6 Each 930.00 5,580.00

direction of Engineer-in-charge.

Providing and Fixing FH-943 Double cylender Floor Spring- for wooden door with

Closing Force EN 3 with Maximum door weight 105 Kg. Maximum door width

950mm.Closing speed : 130° Final closing speed : 15-0°. Hold Open (standard): 90°

MR hold open. Weight of floor spring approx : 6kg, 5,00,000 cycles Tested with 5 Years 6 Each 9100.00 54,600.00

Warranty against manufacturing defect. CE certified for wooden doors all complete

as per the direction of Engineer-in-charge.

Providing and Fixing EFS ACC-001,002 top and Bottom Strap for wooden doors of

MR approved make and model all complete as per the direction of Engineer-in-charge. 6 Each 1100.00 6,600.00

Providing and Fixing EDL 024 Dead lock Back set- 50 mm with Key Hole for wooden

MR doors of approved make and model all complete as per the direction of Engineer-in- 6 Each 900.00 5,400.00

Providing and Fixing ECY 1060- 60 mm SS Cylinder One side knob and one side

MR regular key (3 key) for wooden doors of approved make and model all complete as 6 Each 800.00 4,800.00

per the direction of Engineer-in-charge.

Total Cost of Electrical and wood, Door work (6) 5,97,375.00

A Total Cost of existing Toilet Renovation work (1+2+3+4+5+6) 45,54,225.00

II NEW WASHROOM FOR OFFICERS -2 Nos of (1M+1F)

Demolition of existing walls, cabins and brick / block masonry work & 12mm or

more plaster as required

Dismantling of old plaster or skirting raking out joints and cleaning the surface for

15.56 plaster including disposal of rubbish to the dumping ground within 50 metres lead. 50 Sqmt 45.05 2,252.50

Dismantling/ chipping of concrete: Dismantling & chipping of existing concrete up to

10 mm behind the main bar carefully by low impact high frequency hammer without

damaging the mother concrete including cleaning the surfaces and preparing surface

ready to receive new plaster etc. at all height complete and collecting and stacking of

the debris at the lead of 50m at ground floor in the premises as directed by Engineer

in charge, complete. The rates are inclusive of all materials, labor, machinery,

equipment, tools, tackles etc. and disposal of debris into approved municipal

dumping yards, all complete.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

6.13 designation 7.5 in superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 160 Sqm 1018.05 1,62,888.00

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third

course of half brick masonry.

13.4 12 mm cement plaster of mix :

Digitally signed by SANJAY

Estimate for Toilets Renovation work for M/s. Haryana State Pollution Control Board(HSPCB)

SI.No Description Qty Units Rate (Rs) Total (Rs)

Providing and applying plaster of paris putty of 2 mm thickness over plastered

surface to prepare the surface even and smooth complete.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false

ceiling including disposal of unserviceable material and stacking of serviceable

material with in 50 meters lead as directed by Engineer-in-charge.

Total Cost of Demolition Work (1) 2,81,250.00

2 Ceramic Wall tiles for toilets including painting and signages

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622

(thickness to be specified by the manufacturer), of approved make, in all colours,

shades except burgundy, bottle green, black of any size as approved by Engineer-in-

Charge, in skirting, risers of step sand dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg

per sqm, including pointing in white cement mixed with pigment of matching shade

complete. Size of Tile 1000x1000 mm

Wall painting with acrylic emulsion paint of approved brand and manufacture to give

an even shade :

13.60.1 Two or more coats on new work 101.39 Sqm 137.85 13976.6115

Signage: Various Direction signages of exit and washroom identification with LED

MR-1 glow panel and proper fixture for installation and connection 20"x9" 5 Nos 4,500.00 22,500.00

Total Cost of Eall Tiles, Painting and signages (2) 3,93,750.00

Metal Perforated Grid ceiling tiles made of GI sheet having galvanizing for toilets

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in

true horizontal level, suspended on inter locking metal grid of hot dipped galvanized

steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main

"T" runner with suitably spaced joints to get required length and of size 24x32 mm

made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center

and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm

long spaced between main "T" at 600 mm center to center to form a grid of

1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made

of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm

panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying

false ceiling tiles of approved texture in the grid including, required cutting/making,

opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x

25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm

GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm

spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm

of all T-sections shall be pre-painted with polyester paint, all complete for all heights

as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size

595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing

of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia

12.52.2 holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically 73.00 Sqmt 1746.25 1,27,470.49

polyester powder coated of thickness 60 microns (minimum), including factory

painted after bending and perforation, and backed with a black Glass fiber acoustical

Providing and fixing metal system up to ceiling height, which includes frame work

made of special section power pressed/ roll form G.I. sheet with zinc coating of 120

GSM, consisting of Boral U track 52mm wide having equal flanges of 30mm and

0.55mm thick (Base metal thickness) fastened to the floor slab and ceiling soffit using

rawl plugs with screw at 600mm centers, with first & last fixing point at not greater

MR-2 than 50 mm from either end. Boral C studs 50mm wide having one flange of 34mm, 50.02 Sqmt 1,500.00 75,030.00

other flange 36mm, lip size 6 mm and 0.55mm thick installed perpendicularly within

the flanges of floor and ceiling channels located directly opposite to each other at not

more than 610mm centers. Maintain 5 to 10mm gap between C Stud and web of U

Totsl cost of Metal Ceiling (3) 2,02,500.00

4 Flooring of toilets includes water proofing and Marble stone laying etc.

Providing and laying water proofing treatment to vertical and horizontal surfaces of

depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of

applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound

conforming to IS 2645 in recommended proportions including rounding off junction

of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1

22.3 cement : 3 coarse sand) mixed with water proofing compound in recommended 55 Sqm 774.25 42,583.75

proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd

course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet

should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying flamed finish Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick

11.55 base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement

slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or

Total Cost of water Proofing and flooring works (4) 1,70,775.00

Supply, Installation, Testing & Commissioning of all toilet fixtures including existing

Digitally signed by SANJAY

Estimate for Toilets Renovation work for M/s. Haryana State Pollution Control Board(HSPCB)

SI.No Description Qty Units Rate (Rs) Total (Rs)

Providing and fixing white vitreous china extended wall mounting water closet of size

780x370x690 mm of approved shape including providing & fixing white vitreous

china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4

litre/ 8 litres),including seat cover, and cistern fittings, nuts, bolts and gasket etc

Providing and fixing stone slab with table rubbed, edges rounded and polished, of

size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of

appropriate width with chase cutter and embedding the stone in the chase with

8.10 epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and

finished smooth.

8.10.2 Granite Stone of approved shade 4.00 Sqm 3,542.85 14,171.40

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole

basin mixer of approved quality and make, including painting of fittings and brackets,

cutting and making good the walls wherever required:-

White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single

hole basin mixer

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved

quality) complete with 6 mm thick hard board ground fixed to wooden cleats with

C.P. brass screws and washers complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste

fittings complete.

17.28.2 Flexible pipe

17.34 Providing and fixing toilet paper holder : -

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112

mm distance from wall of standard shape with bracket of the same materials with

17.71 snap fittings of approved quality and colour, weighing not less than 105 gms. 2 Each 146.30 292.60

Providing and fixing CP Brass 32mm size bottle trap of approved quality & make and

as per the direction of engineer in charge.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide

with minimum distances of 37 mm from wall face with concealed fittings

arrangement of approved quality and colour, weighing not less than 88 gms.

Providing ,Fixing of straight / offset type flexible single body push fit type WC pan

connector of with integral single mould sealing fins made of flexible EVA body to be

MR fixed with manufacture supplied grease, including rubber bush / adaptor for use with 2 Each 900.00 1,800.00

C.I pipe as supplied with the pan connector.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube upto 1meter long with

17.16a S.S. Triangular plate to european type W.C. Of approved quality and make as 2 Each 299.35 598.70

approved by engineer in charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of

18.53.1 approved quality conforming to IS:8931 15mm nominal bore 10.00 Each 500.35 5,003.50

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm

length , 15 mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth

18.65 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 2.00 Each 96.75 193.50

Providing & Fixing of Grab bar 600 mm of non slipping grip as per standard

specification of use in disabled toilet complete with brackets suitable for wall

installation as per approved sample complete in all respect.

Providing and fixing of Infrared sensor controlled tap Battery operation with external

battery compartment and 4x AA alkaline batteries including flexible hoses G 3/8 int.

thread x 450 mm with prefilter and flow regulator ; flow volume: max. 3.8 l/min

MR independent of pressure ; can be adjusted to 1.33 lpm (For LEED) with additional 4 Each 22,000.00 88,000.00

areator 28 931 00 99 ; flow pressure: 0,5 - 5 bar ,max. resting pressure 8 bar (Model

no. of 02 172 06 99 of Schell )

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

18.8 pipes & fittings with one step CPVC solvent cement and the cost of cutting chases

and making good the same including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

18.8.1 15 mm nominal dia Pipes 25.00 Mtr. 441.15 11029

18.8.2 20 mm nominal dia Pipes 25.00 Mtr. 513.75 12844

18.8.3 25 mm nominal dia Pipes 22.21 Mtr. 626.05 13906

18.8.4 32 mm nominal dia Pipes 20.00 Mtr. 712.75 14255

Digitally signed by SANJAY

Estimate for Toilets Renovation work for M/s. Haryana State Pollution Control Board(HSPCB)

SI.No Description Qty Units Rate (Rs) Total (Rs)

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC

pipes for soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring

joints, including all neccessary specials and fittings (confirming to IS:14735) i.e.

bends, tees, junctions (with or without doors), reducers, WC connectors, couplers,

expansion joints / bellows, cowels, clamps, rubber rings, clean outs etc. fixing at wall/

ceiling/ floor level supported by clamp & hangers etc. in concealed / inside duct /

under floor & basement ceiling / external work etc. including chase cutting as

required, excavation and back filling in all kind of soils, suspended from floor under

false ceiling or embedding the pipes laid under floors / building in 75 mm. alround

1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) including cost of shuttering for proper completion of the work,

breaking and making good the walls and floors etc. after pipes have been duly laid

and tested. The rubber ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers

etc on 50x50x5 mm slotted angle. The cost will include all support arrangements. The

work includes commissioning of all pipes lines as per drawings and specifications and

as directed by engg-in-charge at site.

110 mm dia (Wall Thickness - 3.2 to 3.8 mm) 20 Mtr. 600.00 12,000.00

75 mm dia (Wall Thickness - 3.2 to 3.8 mm) 20 Mtr. 460.00 9,200.00

Providing and fixing PP white Trap with minimum 50mm water seal with rubber seal

MR on inlet to push fit hopper for indirect waste connections. -

110 mm inlet & 110 mm outlet Long ht 2 Nos 1,505.00 3,010.00

Providing and fixing floor drain (FD) with 50mm outlet and 100 mm inlet having

19mm seal for indirect floor drain (FD).

Providing and fixing Multi Trap (MT) with 50mm outlet and 100 mm inlet having

19mm seal for indirect Multi Trap (MT).

Providing, fixing, testing and commissioning of pipe inlet fittings by fixing Tee 110

x50/110 x75 mm (as required) fixed on 'P' traps for connecting fixture drains/

MR extension pices in PP including fixing and sealing inlet joint with drip seal / Pipe seal 2 Nos 850.00 1,700.00

joint as required complete.

Total Cost of Toilet Accessories including piping work (5) 2,70,675.00

Electrical work includes replacing of electrical wires, Switch sockets, LED lights etc.

And wood work, doors etc as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR

1.7 PVC insulated copper conductor, single core cable in surface/ recessed steel conduit

1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 20.00 meter ₹ 428.00 8,560.00

Supplying and fixing of following sizes of medium class PVC conduit along with

accessories in surface/recess including painting in case of surface conduit, or cutting

the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate

1.24 & switch box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet 15.00 Each ₹ 156.00 2,340.00

1.24.5 6 pin 15/16 amp socket outlet 10.00 Each ₹ 197.00 1,970.00

Supplying and fixing modular blanking plate on the existing modular plate & switch

box excluding modular plate as required.

Supplying and fixing following size/module, GI box along with Modular base & cover

1.27 plate on existing modular metal boxes etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB

distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar,

2.3 neutral bus bar, earth bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, double pole, (single phase and neutral), 240

volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30

2.14 milliamperes in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature

circuit breaker suitable for inductive load of following poles in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

2.10.1 Single pole 10 Each 256 2,560.00

Digitally signed by SANJAY

Estimate for Toilets Renovation work for M/s. Haryana State Pollution Control Board(HSPCB)

SI.No Description Qty Units Rate (Rs) Total (Rs)

Supply, Installation, Testing and Commissioing of Recessed downlightwith HPE (High-

Performance Efficiency) with LED (Light Emitting Diode), system power: 12 W,

Luminous flux of luminaire 1320 lm, 110 LM/W system efficacy, Colour temperature

of 4000 K, Neutral white, CRI > 80, 230V constant current driver, 70% of luminous

flux after 50,000 operating hours; energy-efficient LEDs, direct light emission,

housing in die-cast aluminium, Polyester powder white coloured coat applied over a Each ₹ 2,100.00 25,200.00

5-stage pre-treatment trim, prismatic diffuser for homogenous light distribution,

ZHLS (ZERO HALOGEN LOW SMOKE) wiring, Electronic control gear,

Protection class II, IP 40,

Providing wood work in frames of doors, windows, clerestory windows and other

frames, wrought framed and fixed in position with hold fast lugs or with dash

fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood 0.12 Cum 131576.95 15,789.23

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I)

non-decorative type, core of block board construction with frame of 1st class hard

9.21 wood and well matched commercial 3 ply veneering with vertical grains or cross

bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth

9.23 on all edges of flush door shutters (over all area of door shutter to be measured). 5 Sqm 401.40 2,007.00

Providing and Fixing ESDH 1236-22X922 mm Dtype Handle for wooden doors

Material : Stainless Steel. Finish : Satin Stainless Steel (SSS). of approved make and

model all complete as per the direction of Engineer-in-charge.

Providing and Fixing EMB 245 SS Mortise Lock Body SB/TB for door thickness 25-50

MR mm for wooden doors of approved make and model all complete as per the 2 Each 930.00 1,860.00

direction of Engineer-in-charge.

Providing and Fixing FH-943 Double cylender Floor Spring- for wooden door with

Closing Force EN 3 with Maximum door weight 105 Kg. Maximum door width

950mm.Closing speed : 130° Final closing speed : 15-0°. Hold Open (standard): 90°

MR hold open. Weight of floor spring approx : 6kg, 5,00,000 cycles Tested with 5 Years 2 Each 9100.00 18,200.00

Warranty against manufacturing defect. CE certified for wooden doors all complete

as per the direction of Engineer-in-charge.

Providing and Fixing EFS ACC-001,002 top and Bottom Strap for wooden doors of

MR approved make and model all complete as per the direction of Engineer-in-charge. 2 Each 1100.00 2,200.00

Providing and Fixing EDL 024 Dead lock Back set- 50 mm with Key Hole for wooden

MR doors of approved make and model all complete as per the direction of Engineer-in- 2 Each 900.00 1,800.00

Providing and Fixing ECY 1060- 60 mm SS Cylinder One side knob and one side

MR regular key (3 key) for wooden doors of approved make and model all complete as 2 Each 800.00 1,600.00

per the direction of Engineer-in-charge.

Total Cost of Electrical and wood, Door work (6) 1,99,125.00

B Total Cost of New Toilet for Officers (1+2+3+4+5+6) 15,18,075.00

III WASHROOM CABINS FOR Sr. Env Eng

Demolition of existing walls, cabins and brick / block masonry work & 12mm or

more plaster as required

Dismantling of old plaster or skirting raking out joints and cleaning the surface for

15.56 plaster including disposal of rubbish to the dumping ground within 50 metres lead. 50 Sqmt 45.05 2,252.50

Dismantling/ chipping of concrete: Dismantling & chipping of existing concrete up to

10 mm behind the main bar carefully by low impact high frequency hammer without

damaging the mother concrete including cleaning the surfaces and preparing surface

ready to receive new plaster etc. at all height complete and collecting and stacking of

the debris at the lead of 50m at ground floor in the premises as directed by Engineer

in charge, complete. The rates are inclusive of all materials, labor, machinery,

equipment, tools, tackles etc. and disposal of debris into approved municipal

dumping yards, all complete.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

6.13 designation 7.5 in superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 160 Sqm 1018.05 1,62,888.00

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third

course of half brick masonry.

13.4 12 mm cement plaster of mix :

Providing and applying plaster of paris putty of 2 mm thickness over plastered

surface to prepare the surface even and smooth complete.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false

ceiling including disposal of unserviceable material and stacking of serviceable

material with in 50 meters lead as directed by Engineer-in-charge.

Total Cost of Demolition Work (1) 2,81,250.00

2 Ceramic Wall tiles for toilets including painting and signages

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622

(thickness to be specified by the manufacturer), of approved make, in all colours,

shades except burgundy, bottle green, black of any size as approved by Engineer-in-

Charge, in skirting, risers of step sand dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg

per sqm, including pointing in white cement mixed with pigment of matching shade

complete. Size of Tile 1000x1000 mm

Wall painting with acrylic emulsion paint of approved brand and manufacture to give

an even shade :

Digitally signed by SANJAY

Estimate for Toilets Renovation work for M/s. Haryana State Pollution Control Board(HSPCB)

SI.No Description Qty Units Rate (Rs) Total (Rs)

13.60.1 Two or more coats on new work 101.39 Sqm 137.85 13976.6115

Signage: Various Direction signages of exit and washroom identification with LED

MR-1 glow panel and proper fixture for installation and connection 20"x9" 5 Nos 4,500.00 22500

Total Cost of Eall Tiles, Painting and signages (2) 3,93,750.00

Metal Perforated Grid ceiling tiles made of GI sheet having galvanizing for toilets

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in

true horizontal level, suspended on inter locking metal grid of hot dipped galvanized

steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main

"T" runner with suitably spaced joints to get required length and of size 24x32 mm

made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center

and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm

long spaced between main "T" at 600 mm center to center to form a grid of

1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made

of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm

panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying

false ceiling tiles of approved texture in the grid including, required cutting/making,

opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x

25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm

GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm

spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm

of all T-sections shall be pre-painted with polyester paint, all complete for all heights

as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size

595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing

of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia

12.52.2 holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically 73.00 Sqmt 1746.25 1,27,470.49

polyester powder coated of thickness 60 microns (minimum), including factory

painted after bending and perforation, and backed with a black Glass fiber acoustical

Providing and fixing metal system up to ceiling height, which includes frame work

made of special section power pressed/ roll form G.I. sheet with zinc coating of 120

GSM, consisting of Boral U track 52mm wide having equal flanges of 30mm and

0.55mm thick (Base metal thickness) fastened to the floor slab and ceiling soffit using

rawl plugs with screw at 600mm centers, with first & last fixing point at not greater

MR-2 than 50 mm from either end. Boral C studs 50mm wide having one flange of 34mm, 50.02 Sqmt 1,500.00 75,030.00

other flange 36mm, lip size 6 mm and 0.55mm thick installed perpendicularly within

the flanges of floor and ceiling channels located directly opposite to each other at not

more than 610mm centers. Maintain 5 to 10mm gap between C Stud and web of U

Totsl cost of Metal Ceiling (3) 2,02,500.00

4 Flooring of toilets includes water proofing and Marble stone laying etc.

Providing and laying water proofing treatment to vertical and horizontal surfaces of

depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of

applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound

conforming to IS 2645 in recommended proportions including rounding off junction

of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1

22.3 cement : 3 coarse sand) mixed with water proofing compound in recommended 55 Sqm 774.25 42,583.75

proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd

course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet

should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying flamed finish Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick

11.55 base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement

slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or

Total Cost of water Proofing and flooring works (4) 1,70,775.00

Supply, Installation, Testing & Commissioning of all toilet fixtures including existing

Providing and fixing white vitreous china extended wall mounting water closet of size

780x370x690 mm of approved shape including providing & fixing white vitreous

china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4

litre/ 8 litres),including seat cover, and cistern fittings, nuts, bolts and gasket etc

Providing and fixing stone slab with table rubbed, edges rounded and polished, of

size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of

appropriate width with chase cutter and embedding the stone in the chase with

8.10 epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and

finished smooth.

8.10.2 Granite Stone of approved shade 4.00 Sqm 3,542.85 14,171.40

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole

basin mixer of approved quality and make, including painting of fittings and brackets,

cutting and making good the walls wherever required:-

Digitally signed by SANJAY

Estimate for Toilets Renovation work for M/s. Haryana State Pollution Control Board(HSPCB)

SI.No Description Qty Units Rate (Rs) Total (Rs)

White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single

hole basin mixer

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved

quality) complete with 6 mm thick hard board ground fixed to wooden cleats with

C.P. brass screws and washers complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste

fittings complete.

17.28.2 Flexible pipe

17.34 Providing and fixing toilet paper holder : -

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112

mm distance from wall of standard shape with bracket of the same materials with

17.71 snap fittings of approved quality and colour, weighing not less than 105 gms. 2 Each 146.30 292.60

Providing and fixing CP Brass 32mm size bottle trap of approved quality & make and

as per the direction of engineer in charge.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide

with minimum distances of 37 mm from wall face with concealed fittings

arrangement of approved quality and colour, weighing not less than 88 gms.

Providing ,Fixing of straight / offset type flexible single body push fit type WC pan

connector of with integral single mould sealing fins made of flexible EVA body to be

MR fixed with manufacture supplied grease, including rubber bush / adaptor for use with 2 Each 900.00 1,800.00

C.I pipe as supplied with the pan connector.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube upto 1meter long with

17.16a S.S. Triangular plate to european type W.C. Of approved quality and make as 2 Each 299.35 598.70

approved by engineer in charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of

18.53.1 approved quality conforming to IS:8931 15mm nominal bore 10.00 Each 500.35 5,003.50

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm

18.21.2.1 length , 15 mm nominal bore 10.00 Each 85.20 852.00

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth

18.65 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 2.00 Each 96.75 193.50

Providing & Fixing of Grab bar 600 mm of non slipping grip as per standard

specification of use in disabled toilet complete with brackets suitable for wall

installation as per approved sample complete in all respect.

Providing and fixing of Infrared sensor controlled tap Battery operation with external

battery compartment and 4x AA alkaline batteries including flexible hoses G 3/8 int.

thread x 450 mm with prefilter and flow regulator ; flow volume: max. 3.8 l/min

MR independent of pressure ; can be adjusted to 1.33 lpm (For LEED) with additional 4 Each 22,000.00 88,000.00

areator 28 931 00 99 ; flow pressure: 0,5 - 5 bar ,max. resting pressure 8 bar (Model

no. of 02 172 06 99 of Schell )

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

18.8 pipes & fittings with one step CPVC solvent cement and the cost of cutting chases

and making good the same including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

18.8.1 15 mm nominal dia Pipes 25.00 Mtr. 441.15 11029

18.8.2 20 mm nominal dia Pipes 25.00 Mtr. 513.75 12844

18.8.3 25 mm nominal dia Pipes 22.21 Mtr. 626.05 13906

18.8.4 32 mm nominal dia Pipes 20.00 Mtr. 712.75 14255

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC

pipes for soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring

joints, including all neccessary specials and fittings (confirming to IS:14735) i.e.

bends, tees, junctions (with or without doors), reducers, WC connectors, couplers,

expansion joints / bellows, cowels, clamps, rubber rings, clean outs etc. fixing at wall/

ceiling/ floor level supported by clamp & hangers etc. in concealed / inside duct /

under floor & basement ceiling / external work etc. including chase cutting as

required, excavation and back filling in all kind of soils, suspended from floor under

false ceiling or embedding the pipes laid under floors / building in 75 mm. alround

1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) including cost of shuttering for proper completion of the work,

breaking and making good the walls and floors etc. after pipes have been duly laid

and tested. The rubber ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers

etc on 50x50x5 mm slotted angle. The cost will include all support arrangements. The

work includes commissioning of all pipes lines as per drawings and specifications and

as directed by engg-in-charge at site.

110 mm dia (Wall Thickness - 3.2 to 3.8 mm) 20 Mtr. 600.00 12,000.00

75 mm dia (Wall Thickness - 3.2 to 3.8 mm) 20 Mtr. 460.00 9,200.00

Providing and fixing PP white Trap with minimum 50mm water seal with rubber seal

MR on inlet to push fit hopper for indirect waste connections. -

110 mm inlet & 110 mm outlet Long ht 2 Nos 1,505.00 3,010.00

Providing and fixing floor drain (FD) with 50mm outlet and 100 mm inlet having

19mm seal for indirect floor drain (FD).

Digitally signed by SANJAY

Estimate for Toilets Renovation work for M/s. Haryana State Pollution Control Board(HSPCB)

SI.No Description Qty Units Rate (Rs) Total (Rs)

Providing and fixing Multi Trap (MT) with 50mm outlet and 100 mm inlet having

19mm seal for indirect Multi Trap (MT).

Providing, fixing, testing and commissioning of pipe inlet fittings by fixing Tee 110

x50/110 x75 mm (as required) fixed on 'P' traps for connecting fixture drains/

MR extension pices in PP including fixing and sealing inlet joint with drip seal / Pipe seal 2 Nos 850.00 1,700.00

joint as required complete.

Total Cost of Toilet Accessories including piping work (5) 2,70,675.00

Electrical work includes replacing of electrical wires, Switch sockets, LED lights etc.

And wood work, doors etc as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR

1.7 PVC insulated copper conductor, single core cable in surface/ recessed steel conduit

1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 20.00 meter ₹ 428.00 8,560.00

Supplying and fixing of following sizes of medium class PVC conduit along with

accessories in surface/recess including painting in case of surface conduit, or cutting

the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate

1.24 & switch box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet 15.00 Each ₹ 156.00 2,340.00

1.24.5 6 pin 15/16 amp socket outlet 10.00 Each ₹ 197.00 1,970.00

Supplying and fixing modular blanking plate on the existing modular plate & switch

box excluding modular plate as required.

Supplying and fixing following size/module, GI box along with Modular base & cover

1.27 plate on existing modular metal boxes etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB

distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar,

2.3 neutral bus bar, earth bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, double pole, (single phase and neutral), 240

volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30

2.14 milliamperes in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature

circuit breaker suitable for inductive load of following poles in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

2.10.1 Single pole 10 Each 256 2,560.00

Supply, Installation, Testing and Commissioing of Recessed downlightwith HPE (High-

Performance Efficiency) with LED (Light Emitting Diode), system power: 12 W,

Luminous flux of luminaire 1320 lm, 110 LM/W system efficacy, Colour temperature

of 4000 K, Neutral white, CRI > 80, 230V constant current driver, 70% of luminous

flux after 50,000 operating hours; energy-efficient LEDs, direct light emission,

housing in die-cast aluminium, Polyester powder white coloured coat applied over a Each ₹ 2,100.00 25,200.00

5-stage pre-treatment trim, prismatic diffuser for homogenous light distribution,

ZHLS (ZERO HALOGEN LOW SMOKE) wiring, Electronic control gear,

Protection class II, IP 40,

Providing wood work in frames of doors, windows, clerestory windows and other

frames, wrought framed and fixed in position with hold fast lugs or with dash

fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood 0.12 Cum 131576.95 15,789.23

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I)

non-decorative type, core of block board construction with frame of 1st class hard

9.21 wood and well matched commercial 3 ply veneering with vertical grains or cross

bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth

9.23 on all edges of flush door shutters (over all area of door shutter to be measured). 5 Sqm 401.40 2,007.00

Providing and Fixing ESDH 1236-22X922 mm Dtype Handle for wooden doors

Material : Stainless Steel. Finish : Satin Stainless Steel (SSS). of approved make and

model all complete as per the direction of Engineer-in-charge.

Providing and Fixing EMB 245 SS Mortise Lock Body SB/TB for door thickness 25-50

MR mm for wooden doors of approved make and model all complete as per the 2 Each 930.00 1,860.00

direction of Engineer-in-charge.

Digitally signed by SANJAY

Estimate for Toilets Renovation work for M/s. Haryana State Pollution Control Board(HSPCB)

SI.No Description Qty Units Rate (Rs) Total (Rs)

Providing and Fixing FH-943 Double cylender Floor Spring- for wooden door with

Closing Force EN 3 with Maximum door weight 105 Kg. Maximum door width

950mm.Closing speed : 130° Final closing speed : 15-0°. Hold Open (standard): 90°

MR hold open. Weight of floor spring approx : 6kg, 5,00,000 cycles Tested with 5 Years 2 Each 9100.00 18,200.00

Warranty against manufacturing defect. CE certified for wooden doors all complete

as per the direction of Engineer-in-charge.

Providing and Fixing EFS ACC-001,002 top and Bottom Strap for wooden doors of

MR approved make and model all complete as per the direction of Engineer-in-charge. 2 Each 1100.00 2,200.00

Providing and Fixing EDL 024 Dead lock Back set- 50 mm with Key Hole for wooden

MR doors of approved make and model all complete as per the direction of Engineer-in- 2 Each 900.00 1,800.00

Providing and Fixing ECY 1060- 60 mm SS Cylinder One side knob and one side

MR regular key (3 key) for wooden doors of approved make and model all complete as 2 Each 800.00 1,600.00

per the direction of Engineer-in-charge.

Total Cost of Electrical and wood, Door work (6) 1,99,125.00

C Total Cost of New Toilet for Sr. Environmental Engg (1+2+3+4+5+6) 15,18,075.00

1 Total Cost of Toilet Work (A+B+C) including GST 75,90,375.00

Digitally signed by SANJAY

ESTIMATE FOR FURNITURE AT HSPCB HEAD OFFICE BUILDING AND REGIONAL OFFICES

SI.No Item Description Qty Units Rate Amount

Supply and Installation of Computer Table made of approximate size 1200

(W) x 600 (D) x 750 (H), Table top is made of 25mm thick E-1 grade particle

board. Table color and shade shall be finalise as per full satisfaction and

selection of the Client/ Engineer Incharge.

Supply and Installation of Computer Mesh Chair with Position high back Chair

Revolving type Mid Back. color and shade shall be finalise as per full

satisfaction and selection of the Client/ Engineer Incharge.

Supply and Installation of Regional Officer L- Shape table with table

3 NDSR-3 approximate size of 1650 (W) x 1950 (D) x 750 (H). Table Comes with a Top 2 Nos 85000 170000

and legs are made of 25mm thick Particle Board (E-1 Grade), melamine finish,

Chamfered edges, Soft closing doors, Aluminium handles with ERU Wire

management . color and shade shall be finalise as per full satisfaction and

selection of the Client/ Engineer Incharge.

Supply and Installation of AEE L- Shape table with table approximate size of

1650 (W) x 1950 (D) x 750 (H). Table Comes with a Top and legs are made of

25mm thick Particle Board (E-1 Grade), melamine finish, Chamfered edges,

Soft closing doors, Aluminium handles with ERU Wire management . color and

shade shall be finalise as per full satisfaction and selection of the Client/

Engineer Incharge.

Regional Officer Chairs: Supply and Installation of high back Revolving Mesh

5 NDSR-5 fabric Chair with Adjustable Headrest. color and shade shall be finalise as 1 Nos 24426 24426

per full satisfaction and selection of the Client/ Engineer Incharge.

AEE Chairs without head rest: Supply and Installation of high back Revolving

6 NDSR-6 Mesh Chair without Headrest. color and shade shall be finalise as per full 1 Nos 19676 19676

satisfaction and selection of the Client/ Engineer Incharge.

Big Almirah (Steel): Supply and Installation of Steel Almirah having 4 shelves

making 5 compartments with Lock safety facility and making it highly corrosive

resistant, superior Finish–Powder coating with approximate size of Almirah is

1870 (H) x 900(W)x 450 (D). color and shade shall be finalise as per full

satisfaction and selection of the Client/ Engineer Incharge.

Small Almirah (Steel): Supply and Installation of Steel Almirah with Lock

safety facility and making it highly corrosive resistant, superior Finish–Powder

coating with approximate size of Almirah is 1168 (H) x 900(W)x 450 (D). color

8 NDSR-8 and shade shall be finalise as per full satisfaction and selection of the 2 Nos 29515 59030

Client/ Engineer Incharge

9 NDSR-9 Visitor Chairs with cushion: Supply and Installation of Visitor Mesh chairs with 8 Nos 16284 130272

cushion, arm rest, back type shall be breathable mesh . Color and shade shall

be finalise as per full satisfaction and selection of the Client/ Engineer

Digitally signed by SANJAY

Providing and placing panel & tile based modular workstation, with

partition thickness as 52.4 mm thk and ht - 1200 including powder

coated aluminium trims. Tiles: Combination of top tiles are fabric

magnetic/fabric/fabric tackable/white board/glass writing board/ clear glass

tile/ plain metal/ prelam tile. Bottom tiles - Plain metal/ fabric magnetic /

fabric / laminated /prelam. The panel thickness comprises of 38mm (35 mm

Minimum) thick paper honeycomb + 3mm MDF on each sides + 0.6mm

decorative laminate or fabric on both sides. The uprights and horizontals shall

be made of aluminium extrusion having average wall thickness of 1.2 mm

& powder coated with epoxy- polyester powder. Particle board framing is

10 NDSR-10 used on outer boundary of these blocks as well as intermediately at 20 Nos 62230 1244600

certain locations forming conduit for passing cables. These blocks are

located in the mid segment of the panels and can be provided with cutouts

for mounting switch boxes (above or below the worktops). Top tiles can be

offered in variety of combinations. The fins along the depth shall be 22.8mm

thick. Worksurface- out of 25 mm thk prelam particle board with flat pvc lipping

edge banding of size 1200mm x 600mm x 750H. Brackets shall be made from

2mm thick CRCA steel. Pedestals with legs- pedestal flat metal front, free

standing central locking of size 390 mm w x 435 mm d x 646 mm height 3dr =

2box+1file. The work shall be carried out as per the instructions and

guidance received from engineer incharge. The product must be UL

Greenguard, BIFMA Level 3 certified. Complete with all accessories.

Total Cost of Furniture including GST@18% A 26,20,212.00

Digitally signed by SANJAY