WBPWDEEIALI/NIET46CSD/25-26

Taking out Mirzapur or glazed porcelain tiles carefully bychiselling from walls or floor including stacking serviceablematerial as directed.

Stripping off worn out plaster and raking out joints of walls, celings etc. up to any height and in any floor including removing rubbish with in a lead of 75 m as directed.

(a) Applying 2 coats of bonding agent with synthetic multi functional rubberemulsion having adhesive and water proofing properties by mixing with waterin proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer'sspecification [Cement to be supplied by the Department]

(b) Applying 2 coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturer's specification for water proofing layer in water tank etc. (No Departmental Cement is required)

Ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttring and reinforcement, if any, in ground floor as per relevant IS codes. (a) Pakur Variety.

Cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed, cutting the concrete to regular shape, wire rushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge.

Cleaning the exposed reinforcement preferably upto full diameter by wire brush, applying two coats of polymer based rust removing compound left for 24 hours, removing the coating and then applying two (2) coats of polymer modified anti corrosive protective coating formulated to inhibit the corrosion of reinforcement as per manufacturer's specification] [Mode of measurement:The affected surface area of einforcement shall be considered for payment]

Guniting concrete surface with cement mortar (25 mm nominal thick) applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification.

Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. (i) with 1:6 cement mortar. (c)15 mm. thick plaster. Ground Floor

1st floor

2nd floor

3rd floor

4th floor

5th floor

6th floor

7th floor

8th floor

9th floor

(ii) With 1:4 cement mortar . (c)10 mm. thick plaster.

1st floor

2nd floor

3rd floor

4th floor

5th floor

6th floor

7th floor

8th floor

9th floor

125 mm. thick brick work with 1st class bricks in cement mortar (1:3) in ground floor.

Supplying,Fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. (a) Area of each tile up to 0.09Sq.m. (i) Coloured decorative.

(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. (a) Area of each tile up to 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 1st. floor)

(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. (a) Area of each tile up to 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 2nd floor)

(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. (a) Area of each tile up to 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 3rd floor)

(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. (a) Area of each tile up to 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 4th floor)

(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. (a) Area of each tile up to 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 5th floor)

(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. (a) Area of each tile up to 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 6th floor)

(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. (a) Area of each tile up to 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 7th floor)

(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. (a) Area of each tile up to 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 8th floor)

(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. (a) Area of each tile up to 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 9th floor)

(B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile the above 0.09Sq.m. (i) Coloured decorative.

(B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile the above 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 1st. floor)

(B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile the above 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 2nd floor)

(B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile the above 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor - 3rd floor)

(B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile the above 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor -4th floor)

(B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile the above 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor -5th floor)

(B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile the above 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor -6th floor)

(B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile the above 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor -7th floor)

(B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile the above 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor -8th floor)

(B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile the above 0.09Sq.m. (i) Coloured decorative. (Add. above ground floor -9th floor)

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface.

supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar , end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction . ( cost of concrete will be paid separately). (b) 40mm x 6mm, 200mm Length .

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be corrected up to three decimals).(a) 1st class Best Indian teak. (c) Sal : Siliguri.

Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan orsimilar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings in ground floor (b) 32 mm thick shutters (single leaf)

Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria. In ground floor. (b) 32 mm

(i) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16 mm dia rod with centre bolt and round fitting. (C)300 mm long .

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S.230/72) fitted and fixed complete:. (a) With continuous plate base (hexagonal/round rod). (ii) 100 mm grip x 10 mm dia rod .

(a) With continuous plate base (hexagonal/round rod). (vii) 150 mm grip x 12 mm dia rod.

(i) Hydraulic door closer of approved quality as per I.S.I. standard fitted and fixed complete :. (b) Medium (I.S.I. size 2).

Labour for taking out steel door and window frame for repairs and re-fixing the same (or replacement by new one) including mending good damages (excluding the cost of repair of damages) and applying a protective coat of paint. Up to one sq.m. area of frame.

(b) Priming one coat on timber or plastered surface with synthetic enamel oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand parpering etc. in cluding using of approved putty etc. on the surface , if necessary. (a) On timber or plastered surface: (2)With other than hi gloss of approved quality. (iv) Two coats (with any shade except white).

(b) On steel or other metal surface: (2)With other than hi gloss of approved quality. (iv) Two coats (with any shade except white).

Supplying, fitting and fixing PVC pipes of approved make of of Schedule 80 (medium duty) conforming to ASTMD-1785 and threaded to match with GI Pi;es as per IS:1239 (Part-I) with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting piles, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials and two coats of painting with approved paint in any position above ground. For Exposed Work PVC Pipes. 15 mm dia.

For Exposed Work PVC Pipes. 32 mm.

Supplying, fitting and fixing Peet's valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I marking with fittings(tested to 21 kg per sq.cm.). (Note: Item (vii),(viii) and (ix) to be done as per specific direction of the Engineer-in-charge). 32 mm.

Supplying, fitting and fixing bib cock or stop cock. PTMT (Polytetra Bib Cock / Stop Cock (PRAYAG)15 mm

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. Specification with P.V.C. fittings complete, C.I. brackets including two coats of painting to bracket etc.

Supplying PVC water storage tank of approved quality with closed top weith lid (Black) - Multilayer. 2000 litre capacity.

Labour for hoisting plastic water storage tank. Above 1500 litre upto 5000 litre capacity. Upto 1st story from G.L.

Above 1500 litre upto 5000 litre capacity. Extra for each additional story.

Wash basin white vitreous china of approved make (without fittings) supplied, fitted and fixed in position on 75mm X 75mm X 75mm wood blocks and C.I. Brackets including two coats of painting of C.I. Brackets. 550 mm x 400 mm size.

Supplying, fitting & fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P.nut, 15mm dia. 750 mm long.

Supplying, fitting and fixing pillar cock of approved make. PTMT Pillar Cock-15 mm. (PRAYAG).

Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. With 'P' trap.

Supplying, fitting and fixing Flat back urinal (half stall urinals) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. 470 mm X 280 mm X 340 mm.

Supplying, fitting and fixing urinals flush pipe fittings of approved brand. C.P. urinals flush pipe fiitngs range of two.

Supplying, fitting and fixing Closet seat of approved make w

ith lid and C.P. hinges, rubber buffer and brass screws supplied, fitted and fixed complete. E.W.C. . Bestolite (solid type) black.

Supplying, fitting and fixing Half round channel with or without outlet as required set in cement concrete(6:3:1) with jhama chips complete.(Payment of concrete will be paid seperately). 600 mm X 100 mm. White vitreous chinaware.

Supplying, fitting and fixing 18 mm thick marble partition slab with chawk doongri marble square cut both side polished with two front corners rounded and edges polished.

Supplying, fitting and fixing bevelled edge mirror 5.5 mm thick silver red as per I.S. 3438/1965 together with brass C.P. hinges. 600 mm X 450 mm.

Supplying, fitting and fixing liquid soap holder. PTMT (Prayag or equivalent).

Supplying, fitting and fixing towel rail with two brackets. Aluminium. 25 mm dia. and 600 mm long.

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 . Single socketed 3 meter length. 160 mm.

Fittings. W.C. Connector (450m m long) W/lipring. 75mm.

110x110 P Trap. 75mm..

Reducing Tee 160 x 110mm. 75mm..

W.C. Ring. 110 mm.

Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any foor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Enginer-in-charge) Payment will be made on centre line measurement of the total pipeline including specials.). Above ground. 160 mm dia.

Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete. (A) UPVC PIPES. (iii) 160mm Dia.

(B) UPVC fitting:. (a) plain tee. (iii) 160mm Dia.

Constructing Inspection pit to a depth of 1.5 metre (inside), 250 mm thick 1st class brick work (1:4) in all sides over a layer of jhama brick soiling and 150 mm thick cement concrete with stone chips (1:3:6) including necessary earth work, fitting and fixing approved type S.W. master trap, constructing masonry invert with cement concrete (1:1.5:3) with stone chips, plastering inside and outside( outside upto 300 mm below G.L.) with 20 mm thick cement plastering (1:4) and neat cement punning, including, supplying, fitting and fixing one 560 mm dia. R.C.C. manhole cover of approved make with R.C.C slab of 100 mm thick with cement concrete (1:1.5:3) with stone chips including necessary rreinforcement(upto 1%) and shuttering and necessary corbelling brick work(1:4) so that the R.C.C. cover slab rests 150 mm above adjucent G.L., cement plaster(1:4) 10 mm thick on all external surfaces of the top slab as directed complete in all respect and remeval of surplus earth with all costs of labour and materials (excluding the cost of master trap only). 1050 mm X 750 mm(inside) chamber including fitting and fixing S.W. master trap of 225 mm dia. of approved make. With Pakur variety. (OTHER MANUFACTURES NOT SPECIFIED)

Extra for additional depth beyond 1.5 metre. For (iii) and (iv).

Supplying, fitting and fixing in position R.C.C. Manhole/pit cover of approved make with rim of approved make (Heavy type). 560 mm dia.

Cleaning silt of master trap pit.

Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite door frame as per approved section with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to safisfy IS: 4020 door testing performance criteria. (i) 66mm x 90mm.