PERIODICAL AND ALLIED SERVICES TO CERTAIN BLDG IN MAP ACCN AT AF STN ADAMPUR

Amount

BR WORKS

PCC type E-2 (1:5:10), using 40 mm graded crushed stone aggregates as in filling & mass concrete, complete all as specified and directed

Plain Cement concrete (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate as in coping,weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Reinforced cement concrete, type B-1, (1:2:4), using 20 mm graded crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, and in shelves and the like complete all as specified and directed.

Brick work using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified and directed.

Brick work in half brick thick wall using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:4), complete all as specified and directed.

Cutting holes into or through RCC/brick walls built in cement mortar exceeding half brick thick but not exc one brick thick for inserting angle/tee/pipe/ hold fast or similar purposes etc. and making good in cement mortar 1:3 or cement concrete 1:2:4, Type B-1 as required complete all as specified and directed.

Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) with fair finished flat surfaces of concrete, complete all as specified and directed.

Factory made, 35 mm thick, second class hard wood, plain framed, hammer marked, skelton shutter (two panel to receive wire gauge) with lock rail . The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Factory made, 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides,ISI marked, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded wood grain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and wood grain colour PVC sheet for top rail, lock rail and bottom rail, panelling of wood grain colour PVC sheet to be fitted in the MS frame welded / sealed to the stile and rails with suitable PVC sheet beading and jointed together with solvent cement as specified in SSR Part II, complete all all as specified and directed.

Factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm thick wood grain colour PVC sheet reinforced with mild steel square tube, suppling & fixing in opening, complete all as specified and directed.

Plywood 6 mm thick, 5 ply type BB commercial BWR one side laminate confirming to IS: 303 fixed on frame, IN REPAIRS, complete all as shown and directed.

Plywood 12 mm thick, 7 ply type BB commercial BWR one side laminate confirming to IS: 303 fixed on frame, IN REPAIRS, complete all as shown and directed.

Plywood 18 mm thick, 12 ply type BB commercial BWR one side laminate confirming to IS: 303 fixed on frame, IN REPAIRS, complete all as shown and directed.

Ball bearing runners 45mm telescopic channel (20 inch) full extension load capacity 50 kgs complete all as specified and directed.

Aluminium anodised barrel tower bolt of extruded section 150 mm long, ISI marked, complete all as specified and directed.

Aluminium alloy, anodised, ISI marked sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 300 mm long, complete all as specified and directed.

Stainless steel 100mm long butt hinges with stainless steel screws, ISI marked complete all as specified and directed. MAKE: PRAYAG CAT HG-3414 or equivalent make mentioned in Appendix 'B'

Mild steel ordinary rat tail rod pattern helical door spring 250 mm long including roller and roller plate, complete all as specified and directed.

Aluminium anodised handles cast type 75 mm long, ISI marked complete all as specified and directed.

Extruded aluminium anodised handles fabricated type 125 mm long with plate , ISI marked complete all as specified and directed.

Hasp and staple, safety type,size 75 mm aluminium anodised including bolt to hinge plate and fixed with screws of , ISI marked complete all as specified and directed.

Stainless steel conduit 20 mm bore, cut to size and erected in position as curtain rod on backets, with & including SS decorative finials & brackets, PVC rings @ 10 nos. per metre, fixed to walls with PVC rawl plugs & SS screws, IN REPAIRS, complete all as specified and directed.

Double leg aluminium anodised door stopper 150mm long with rubber foot, ISI marked and fixed to bottom rail of doors with steel screws, complete all as specified and directed.

Stainless steel 100mm size auto soft closing hydraulic hinges fixed with stainless steel screws, ISI marked complete all as specified and directed.

Mild steel chromium plated solid handle, 100mm suitable for cupboard shutter, complete all as specified and directed.

Magnetic catchers for cupboars shutters 50mm long with plate, complete all as specified and directed.

Galvanized mild steel wire cloth 0.45 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or galvanized wire staples,complete all as specified and directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or steel wire staples IN REPLACEMENT, complete all as specified and directed.

Framed mild steel work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-290-Gde E-165, complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Mild steel work as in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) quality confirming to grade Fe-290-Gde E-165, complete all as specified and directed.

Aluminium window and ventilator shutters side hung type with styles & rails made out of section size 47-48 mm x 44-45 mm (wall thickness not less than 1.58 mm), anodised alumnium glazing snap beading (having wall thickness not less than 0.90 mm), rubber neoprene packing including joining cleats & screws etc as per manufacturers instructions, complete all as specified and directed. NOTES: (a) Each shutter shall have 2 Nos. 125 mm long almn handles and 02 No. 75 mm size stainless steel/almn butt hinges & one no. almn hook & eye. (b) Glass and other filling materials in panels including wire cloth and almn grill shall be measured & paid for separately under respective item of BoQ.

Welding in repairs metal thickness n exc 6mm & exc 2.5cm in length complete all as specified and directed.

Factory made pre painted pressed steel frames, conforming to IS, having profile 105 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete, all as specified.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/ cladding to wall, bent to curve, fixed with self tapping screws complete all as specified and directed.

Water Proofing Treatment to RCC sunken surfaces comprising of : -

Rendering 15 mm thick (Average thickness) rendering on sunken surfaes including flashings, finished even and fair in cement mortar (1:4), using water proofing compound as per recommended ratio, after brushing cement slurry @ 1.20 kg/Sq. m, complete all as specified. NOTE: Supply only WPC will be measured & paid for separately under respective item of BoQ.

LDPE sheet 150 micron laid over applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq. m & adjoining vertical surfaces including applying bitumenous primer @ 0.40 litre per square metre over clean RCC/plastered roof surfaces complete all as specified and directed.

18/19 mm thick high density moisture resistant (HDMR) board, flat pressed, fixed as in modular kitchen cabinets, cupboards, shelfs or similar works with necessary screws complete all as specified and directed.

Decorative laminates type I, 0.5 mm thick of surface finish, colour and pattern as approved , fixed with approved adhesive complete all as specified and directed.

Decorative laminates type I, 0.9-1 mm thick of surface finish, colour and pattern as approved , fixed with approved adhesive complete all as specified and directed.

High quality solid colour (matching shade) PVC edge banding tape not less the 3 mm thick having 18/19 mm width fixed with approved adhesive to HDMR board complete all as specified and directed.

2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach srew and washer in roof , wall etc. IN REPAIRS, complete.

25 mm thick, cement concrete type B-0, 1:2:4 using 12.5 mm graded stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed

75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, and joints shall be sealed with joint sealing comound grade 'A' complete all as specified and directed.

100 mm thick, cement concrete type D-2, 1:4:8 using 40 mm graded stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed.

Machine cut Kota stone slab flooring 18-22 mm thick, for staircase , laid over over & including 20 mm thick (average thickness) cement mortar (1:3) screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (Granite finish) complete all as specified and directed.

Machine cut Kota stone slab 18-22mm thick on vertical surfaces as in staircase riser skirting/ dado etc over and including 10 mm thick rendering in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed

Granite jet black shade, 15-18 mm thick,as in step, jambs, cooking platform and like, machine cut, machine polished, bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:4), complete all as specified and directed.

Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified and directed.

Glazed ceramic coloured tiles 7mm thick, area of each tile exc. 0.17 Sq.m but n. exc. 0.19 Sq.m on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.06 Sq.m but n. exc. 0.11 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.18 Sq.m but n. exc. 0.36 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.18 Sq.m but n. exc. 0.38 Sq.m, on vertical surfaces as in skirting etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified.

80 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of shape approved by GE, made by table vibratory method using PU mould, laid in required pattern over and including 50mm thick compacted bed of coarse sand, compacting through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

Repairing of RCC projection chhajjas, roof, facia etc by necessary preparation. Scraping cutting, chiseling derusting and cleaning of exposed reinforcement with antirust zink nich prime solution and a coat of bonding agent, surfaces of damaged, loose RCC with micro concrete 20 to 30mm thick and reinforcement with chicken mesh of weight not more than n.exc 3 kg/Sq.m (if reqd) with or without facia and finished with cement and sand mortar (1:3) using coarse sand and work in patches of area n.exc 5 Sq.m and thickness of RCC member n.exc 70 mm incl necessary formwork at any height/location complete all as specified. NOTE: The rate quoted by the contractor shall included for chicken mesh, scaffolding and necessary formwork upto triple storey bldg.

Rendering 5 mm thick on fair faces of concrete surfaces, finished even and smooth on ceiling in cement mortar (1:3), complete all as specified and directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:6) complete all as specified.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), mixed with water proofing compound as per manufacturers instructions, complete all as specified. NOTE: WPC will be measured and paid for separately under respective item of BoQ.

Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified and directed.

Supply only water proofing compound, ISI marked, complete all as specified and directed.

One coat of interior acrylic distemper/oil bound distemper on old ceiling surfaces, including preparation of surfaces, complete all as specified and directed.

Two coats of interior acrylic distemper/oil bound distemper on new ceiling surfaces, including preparation of surfaces, complete all as specified and directed.

Two coat of white wash on old wall surfaces, including preparation of surfaces, complete all as specified.

One coat of interior acrylic distemper/oil bound distemper on old wall surfaces, including preparation of surfaces, complete all as specified and directed.

Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces as specified. (preparatory to paint as directed). (b) Two coats of interior acrylic distemper/oil bound distemper over and including a coat of interior primer.

Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of interior acrylic distemper/oil bound distemper over and including a coat of interior primer.

Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: - a) Applying wall care putty, in two coats & smoothening the surfaces as specified. (preparatory to paint as directed).complete all as specified. (b) Two coats of exterior acrylic emulson over and including a coat of water based exterior primer complete all as specified.

Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of exterior acrylic emulsion over and including a coat of water based exterior primer.

Plain tinted sheet glass, 5-6 mm thick, ordinary quality duly sticked with solar control reflective type film, having thickness not less than 25 micron and fixed air tight with neoprene packing & almn glazing clips, for aluminium/uPVC sections, complete all as specified and directed. .

Plain tinted sheet glass, 5-6 mm thick, ordinary quality duly sticked with solar control reflective type film, having thickness not less than 25 micron and fixed air tight with neoprene packing & almn glazing clips, for aluminium/uPVC sections,including hacking down old sheet glass complete all as specified and directed. .

Applying one coat (finishing coat) of synthetic enamel paint, including preparation of old painted wood and wood based surfaces of any description not other wise described over 10cm width or girth and complete all as specified and directed.

Applying one coat (finishing coat) of synthetic enamel paint including peparation of old painted steel & iron surfaces of any description not other wise described over 10cm width or girth, complete all as specified and directed.

Two coats of synthetic enamel paint over & including a coat of pink primer over new wood and wood based surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified.

Two coats of synthetic enamel paint over & including a coat of red oxide primer over new steel or iron surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified.

Disconnecting existing tanks of capacity exceeding 500 litre but not exceeding 1000 litre, setting aside (or lowering if required) for cleaning/roof repair etc. and hoisting, reconnecting and re-fixing in position after necessary cleaning by removing all scale and dirt etc. including cleaning mouth of circulating service pipes complete all as specified and directed

500 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, IN REPAIRS, complete all as specified including the following acessories: - (i) Gun metal ball valves, high pressure, with metal rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, IN REPAIRS, suitable for 20 mm bore GI pipe, complete all as specified. (iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for 20 mm bore GI tubes, ISI marked, screwed both ends for iron pipe, IN REPAIRS, complete all as specified. (iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, IN REPAIRS, complete all as specified and directed.

1000 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, IN REPAIRS, complete all as specified including the following acessories: - (i) Gun metal ball valves, high pressure, with metal rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, IN REPAIRS, suitable for 20 mm bore GI pipe, complete all as specified. (iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for 20 mm bore GI tubes, ISI marked, screwed both ends for iron pipe, IN REPAIRS, complete all as specified and directed. (iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, IN REPAIRS, complete all as specified.

Steel tubes 15 mm bore ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and directed.

Steel tubes 20 mm bore ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and directed.

Angular stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 6510 or equivalent make mentioned in Appendix 'B'.

Concealed stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 6518 or equivalent make mentioned in Appndix 'B'.

Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 6508 or equivalent make mentioned in Appendix 'B'.

Centre hole basin mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS complete all as specified and directed. MAKE: KEROVIT Cat No. KB111027 or equivalent make mentioned in Appendix 'B'.'.

Wall mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS complete all as specified and directed. MAKE: KEROVIT Cat No. KB511021 or equivalent make mentioned in Appendix 'B'.'.

Sink mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS complete all as specified and directed. MAKE: KEROVIT Cat No. KB511024 or equivalent make mentioned in Appendix 'B'.'.

Overhead ABS shower with cast copper alloy chromium plated arm 225 mm long with flange and fixed in position, IN REPAIRS, complete. MAKE: PRAYAG Cat BS-76 or equivalent make mentioned in Appendix 'B'..

Brass chromium plated towel rail 500-600 mm long, fixed to wall with SS screws and PVC rawl plugs, complete all as specified and directed. MAKE: PRAYAG Cat No. BA-10 or equivalent make mentioned in Appndix 'B'.

Glass shelf 500x125 mm with brass brackets and fixed to wall with chromium plated brass screws and rawl plugs, complete all as specified and directed. MAKE: PRAYAG Cat No. BEA-45 or equivalent make mentioned in Appendix 'B'.

Corner Glass shelf 300 mm with brass brackets and fixed to wall with chromium plated brass screws and rawl plugs, complete all as specified and directed.

Stainless steel soap dish, fixed to wall with SS screws and PVC rawl plugs, complete. MAKE: PRAYAG Cat No. BA-05 or equivalent make mentioned in Appendix 'B'.

Stainless steel round slotted grating with frame, 100 mm size fixed in position with cement joints, complete all as specified.

Stainless steel peg set of six, fixed to wall with SS screws and PVC rawl plugs, complete all as specified and directed. MAKE: PRAYAG Cat No. BEA-30 or equivalent make mentioned in Appendix 'B'.

PVC waste collapsible discharge pipe 32mm dia IN REPAIRS complete all as specified and directed.

PVC connections with PTMT nuts, 450 mm long, IN REPAIRS, complete all as specified and directed.

PVC flushing cistern 10 litre capacity, syphonic action type, any shade, dual flush, ISI marked with flush pipe and all fixing acessories, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 502 or equivalent make mentioned in Appendix 'B'

Vitreous china wash down water closet pan (pedestal pattern), ISI marked, white with uPVC 'S' trap of size 540x365x390 mm, including seat cover and necessary SS Jet spray (L-bend) with 01 metre braded tube fixing acessories, IN REPAIR, complete all as specified and directed. MAKE: PRAYAG Cat No. 4016 or equivalent make mentioned in Appndix 'B'.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm, ISI marked, white, with integral foot rests (excluding flushing cistern and flush pipe), 110x125 size uPVC 'P' trap & necessary joints, lime concrete IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 4055 or equivalent make mentioned in Appendix 'B'

Vitreous China wash basin, white, flat back, size 550 x 400 mm, ISI marked, including fixing acessories like rag bolts etc. with CP waste coupling half or full threaded suitable for & including 32 mm size PVC solid waste pipe, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 4645 or equivalent make mentioned in Appendix 'B'

Health fauset with 1 metre SS tube & hook IN REPAIRS complete all as specified and directed. MAKE: PRAYAG Cat No. BEA-97 or equivalent make mentioned in Appendix 'B'.

uPVC pipes 110 mm external dia, type-A, ISI marked (IS:13592) single socketed in any length with or withou rubber ring joints, fixed under floors/walls as Rain water pipes, IN REPAIRS, complete all as specified and directed.

uPVC pipes 75 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with or without rubber ring joints, fixed under floors/walls as SWR pipes, IN REPAIRS, complete all as specified.

uPVC pipes 110 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with or withou rubber ring joints, fixed under floors/walls as SWR pipes, IN REPAIRS, complete all as specified and directed.

uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 75 mm external dia, IN REPAIRS, complete all as specified and directed.

uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 110 mm external dia, IN REPAIRS, complete all as specified and directed.

uPVC/PVC single T, equal or unequal, suitable for uPVC soil waste discharge pipes 75 mm external dia, IN REPAIRS, complete all as specified and directed.

uPVC/PVC single T, equal or unequal, suitable for uPVC soil waste discharge pipes 110 mm external dia, IN REPAIRS, complete all as specified and directed.

uPVC floor trap, suitable for uPVC soil waste discharge pipes 75 mm ext dia, embedded in PCC type B-1(1:2:4), IN REPAIRS, complete all as specified and directed,

DISMANTLING/DEMOLITION WORKS

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sq.m each and removing from site all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sq.m but not exceeding 4.00 Sq.m each and removing from site all as specified and directed.

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each and removing from site all as specified and directed.

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each, including stacking at directed location and refixing the same on original or new location after resecuring or easing & adjusting, complete all as specified and directed

Taking down cement plaster of any description on brick walls or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking up or down steel tubing 15 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 20 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Demolition brickwork or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floors and pavings not excceding 15cm thickness (above or below ground level) all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided all as specified and directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Dismantling boarding any description complete all as specified and directed.

Dismantling steel sheeting (Corrugated, semi corrugated etc) in roof coverings, complete all as specified and directed.

Notes: Amount of credit for retrieved materials is mentioned in tender documents in pdf form which will be deducted while acceptance of tender offline.

M/S GURBACHAN SINGH (BID ID -3121075)

M/s Sahib and Company (BID ID -3115920)

ELECTRA ENGINEERS (BID ID -3120370)

J.K & Company (BID ID -3120829)

siddharthenterprises (BID ID -3119906)

AAR KAY BEE ENTERPRISES (BID ID -3120125)

LABH SINGH AND SONS (BID ID -3120369)