ADDN/ALTN OF KITCHEN AND TOILETS OF MD ACCN AND CONNECTED B/R WKS AT VASANT RANGE COLONY UNDER AGE B/R-I OF GE (SOUTH) DELHI CANTT-10

Amount

M&L for chipping out spilled and loose concrete cover and derusting steel reinforcement of concrete column, beam, slab, chajjas, parapets and the like as directed up to 25 to 35mm thick roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry including derusting steel wire reinforcement, providing fabric MS wire mesh 75 x 75 x 2 mm as reinforcement to concrete surface applying adhesive/admixture over steel mesh and providing 25 mm average thickness guniting mix using one part of OPC 53 grade and two part of coarse sand mixed with adhesive/admixture @ pressure of 2.5 to 3.00kg/Sqcm by guiniting machine and surface finished even and fair including necessary padding, shuttering/scaffolding, formwork (guniting work to be carried out up to 12 metre height G+4 Bldg) complete all as specified and as directed. Note :- (a) After placing the additional reinforcement all concrete surfaces shall be thoroughly scrubbed with wire brushes, washed with water and allow to dry, apply chemistic polycretes admixture @ 2.25 kg by weight of cement all as per manufacturers instruction. (b) when polymix concreting in taking condition,guiniting is done with polycrete admixture @ 2% by weight of cement all as per manufacturers instructions. (c) Cost of the above aspect shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account.

Demolition of RCC of any description, in any position roofs, floors (other than ground floors), beams staircases, landing, chajjas, RCC overhead tank and similar suspended work and Removing excavated material /demolition material exc. 1.50 km but n exc.5 km including taking down from upto four storey and directedcomplete all as specified.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L for Reinforced cement concrete 1:1.5:3 type B-0 (12.5 mm graded crushed stone aggregate), as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including muld seel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

All as per item No 5.00 here-in-before but 5mm dia and over upto and including 10 mm dia in stirrups, complete all as specified and as directed.

M & L for Granite (of any type) work, 16-18 mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms with necessary hole for gas pipe where ever required and likes over and including cement mortar bedding of 20 mm thick in cement mortar 1:4 including pointing in white cement using marble dust with admixture of pigment to match including rounded edges with shade of granite complete all specified and as directed.

M&L for non skid coloured ceramic tiles jointless 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set & jointed in neat cement slurry & pointed in coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 for laying floor finish including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 350mm x 250mm x 7 mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match in vertical surfaces such as skirting /dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10m thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing coat including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and as directed.

S&F in repair vitreous china squatting pan (Orissa pattern white) long pan fixed size 580x440mm white with integral footrest with 100 mm bore Cast iron `P' or `S' trap complete (excluding flushing cistern and flush pipe) complete all as specified and as directed.

S&F Factory made modular FRP Chajjas with MS Flats 40 x 3mm, minimum 06 Nos Hold and Fastner including cutting/chesling of required thickness (As per manufacturer instruction) of wall or as per direction of GE for upto 4th storey of building and making good to disturbed portion including demolition of reinforcemed cement concrete chajjas by suitable method and as per direction of GE complete all as specified and as directed. Note: Drawing for the complete Job and sample kept in office of AGE B/R-I of GE (South) office.

Demolition of cement concrete in ground floor and paving etc not exc 15 cm thick above or below ground level complete all as specified and as directed.

M&L for applying a coat of cement slurry @ 0.488 Kg/Sqm mixed with tapercreate @ 0.253 Kg/Sqm after cleaning and drying the old/new surfaces then applying the layer of fibre glass cloth while the above coat is still green. The overlap of fibre glass cloth shall be not less than 100 mm and then applying 1.5 mm thick layer @ 1.288 Kg/Sqm mixed with taper create @ 0.570 Kg/Sqm and coarse sand @ 1.289 Kg/Sqm. Allow the treatment to air curing for four hours followed by water curing for 48 hours all as directed.

M&L for 10 mm thick rendering in cement mortar 1: 3 on faces of brick or concrete surfaces finished even and smooth surface wihtout using extra cement on wall of up to four stories bldgs complete all as specified and as directed.

M&L for PCC 1:5:10 type E-2 (using 40 mm graded crushed stone aggregate) as in mass concrete sunken filling complete all as specifiecd and as directed.

M&L for 75 mm thick PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in sub base of flooring complete all as specified and as directed.

M&L for 25 mm thick cement concrete type B-0 1:2:4 (12.5mm graded crushed stone aggregate) as in sub floors finished rough complete all as specified and as directed.

S&F in repair 10 ltr capacity PVC Low level flushing cistern including PVC syphon and float valve with float, PVC long bend for out let connection of cistern with WC complete fixing and connecting bend with WC complete all as specified and as directed.

S&F PVC connections 600 mm long with brass unions at both ends suitable for 15 mm bore pipe, complete all as specified and as directed.

S&F in repair for vitreous china wash hand basin flat back size 550x400 mm size white excluding taps waste chain and plug and porcelain stopper but including brackets and 32 mm dia waste fittings brass chromium plated with long screwed shanks and fly nuts, 32mm x 600 mm long PVC waste pipe complete flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S & F in repair 15 mm bore Brass CP wash hand basin mixer 2 in 1 for mixing hot & cold water screwed down for iron pipe and fixed complete all specified and as directed.

S & F in repair 15 mm bore Brass CP wash wall basin mixer 3 in 1 for mixing hot & cold water screwed down for iron pipe and fixed complete all specified and as directed.

S & F in repair 15 mm bore Brass CP mixer 2 in 1 Sink for mixing hot & cold water screwed down for iron pipe and fixed complete all specified and as directed.

S & F in repair soap dish Chromium plated brass fancy type complete all as specified and as directed.

S & F in repair Towel ring Chromium plated brass fancy type complete all as specified and as directed.

S&F in repairs elegent mirror PVC cabinet without towel rail of size 422 x 622 mm complete all as specified and as directed.

S & F in repair 32 mm to 40mm dia PVC waste pipe for WHB & sink, 60 cm long with union complete all as specified and as directed.

S & F in repair chromium plated brass overhead shower with arm 125 mm with flange with swivel joints, any size, including fixing to steel pipe or union for 15mm bore pipe complete all as specified and as directed.

S & F in repair chromium plated Stop valve/angle valves cast copper alloy, screwed down both, high pressure, with crutch or butterfly handle, screwed both end fixed, complete all as specified and as directed.

S&F in repairs 15 mm size brass chromium plated two way angle valves fancy type cast copper alloy, complete all as specified and as directed.

S & F in repair glass Shelf Corner with frame Chromium plated brass fancy type complete all as specified and as directed.

S&F in repair sheet glass shelf assemble consisting of 5.5mm thick sheet glass shelf with chromium plated bracket guard and railing complete all specified and as directed.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460 mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F stainless steel plate rack made out 1mm thick SS sheet overall size (31X30X10 inch) fixed with steel screws with wooden gutties and complete all as specified and as directed.

Supplying and fixing of 20 mm outer dia CPVC pipes SDR 11 & plain CPVC SCH-40 fitting on walls / ceiling or laying in floors/wall including all fitting such as (brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded adaptor Brass union etc) union, ball valves, flange and tank adaptor including taking down of existing GI tubing 15mm dia and connection complete all specified and as directed.

Cutting chases ,pinning in , making good to facings where required and pointing in cement mortar 1:3 to ends or edges or landings, steps, cills, sunshades,shelves,lintel,etc and cutting in chases for concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth complete alll as specified and as directed.

Excavation in trenches not exceeding 1.5 m in depth and 1.5m in width and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified and directed.

Removing excavated material (soil) n .exc 50m and deposited where directed at a level n exc. 1.5m above the strating point complete all as specified and directed.

Supply and Fixing 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps at one meter of interval including taking down of eaves gutter rain water pipe (any size of pattern) including all fittings, heads, shoes, bends, swan-necks and cleaning or fixing or removal , complete all as specified and as directed.

S&F PVC (SWR) bends of any radius, suitable for 110 mm dia PVC pipes fixed complete all as specified and as directed.

S&F PVC (SWR) Tees with access door, suitable for 110 mm dia PVC pipes fixed complete all as specified and as directed.

Supply and Fixing 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps at one meter of interval including taking down of eaves gutter rain water pipe (any size of pattern) including all fittings, heads, shoes, bends, swan-necks and cleaning or fixing or removal , complete all as specified and as directed.

S&F in repairs for PVC (SWR) bends of any radius, suitable for 75mm dia PVC pipes fixed complete all as specified and as directed.

S&F in repairs for PVC (SWR) Tee with access door, suitable for 75mm dia PVC pipes fixed complete all as specified and as directed.

S&F 75 mm PVC (SWR) floor trap with grating including jointing to waste pipe fixed in solvent complete all as specified and as directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M & L for rendering with Ready Mix Plaster, 10 mm thick on faces of brick work or concrete surfaces, including necessay scaffolding of building upto 4th story complete all as specified and directed.

M & L for rendering with Ready Mix Plaster, 15mm thick on faces of brick work or concrete surfaces, including necessay scaffolding of building upto 4th story complete all as specified and directed.

M & L for rendering with Ready Mix Plaster, 5 mm thick on ceiling surfaces, including necessay scaffolding of building upto 4th story complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall/ceiling sufraces and applying 1mm thick (average thickness) waterproof cement based putty and thereafter apply two coats of super quality weather proof exterior emulsion paint over a coat of primer and 1mm thick (average thickness) waterproof cement based putty using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 Mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by pain manufacturer and as mentioned in PS and accessories for applying apex should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall/ceiling sufraces and applying 1mm thick (average thickness) cement based putty and thereafter apply two coats of oil bound distemper on wall/ceiling surfaces over a coat of primer and using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 Mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by pain manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and as directed.

M&L for complete removal of existing surface by scraping with mechanical wall sander of old plastered wall sufraces and applying 1mm thick (average thickness) waterproof cement based putty and thereafter apply two coats of super quality weather proof exterior emulsion paint over a coat of primer and 1mm thick (average thickness) waterproof cement based putty using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 Mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by pain manufacturer and as mentioned in PS and accessories for applying apex should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and as directed.

M&L for complete removal of existing surface by scraping with mechanical wall sander of old plastered wall surface and applying 1mm thick (average thickness) cement based putty and thereafter apply two coats of oil bound distemper on wall surfaces over a coat of primer and using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 Mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by pain manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and as directed.

M&L for complete removal of existing surface by scraping with mechanical wall sander of old plastered ceiling surface and thereafter apply two coats of oil bound distemper on ceiling surfaces over a coat of primer and using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 Mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by pain manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and as directed.

Demolition of brick work built in cement mortar or cement lime mortar, including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stoneworkcomplete all as specified and directed.

M&L for old size brick work with flyash bricks straight or curved on plan exceedin 6 m mean radius built in cement mortor 1:6, complete all as specified and as directed.

Taking down (Door) chowkats or frames with shutters not exceeding 1.50 Sqm each (without taking off shutters from the frames) complete all as specified and as directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 65 x100 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position SS dash fasteners heavy duty of required dia and length complete all as specified and as directed. Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter, complete all as specified and as directed.

S&F fabricated aluminum window with powder coated (powder coating not less than 50 micron) anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mmx44.45mmx1.5mm thick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc including jointing cleats for fixing builder's hardware fittings & stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including necessary fittings/fixture /aluminum snap beads complete all as specified. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

M&L for poweder coated (powder coatiing not less than 50 micron) aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section (two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening) including provn for making windows air tight, including 95 mm aluminium handle with spring lock, stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4 mm and fixed with steel wire stapples and 5 mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

M&L for 18 mm thick wood plastic composites (WPC) board, 100% solid with density not less than 650 Kg per cubic meter , one side wood grain finished laminated for exposed/external surface , fixed with screws fitted under or above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc complete all as specified and directed. Note : (a) Pattern & design of WPC board to be decided by GE. (b) Items like cupboard knobs, stainless steel channel, CP plate clip hinges to be paid in extra.

Supply, fabrication & installation of box-type modular kitchen cabinets (below/above counter) up to 600 mm depth (or as per actual size at site) made of 18 mm thick HDHMR pre-laminated waterproof & termite resistant board for top, bottom, back, partitions, drawers, shelf etc. Shutters & exposed surfaces made of 18 mm thick HDHMR laminated with 3 mm thick acrylic high gloss sheet on one side and 0.8 mm balancing laminate on other side, factory pressed. Edges finished with PVC edge banding tape applied by edge bending machine etc including auto closing spring loaded hinges(hydraulic type), magnetic catchers, SS handles stainless, steel soft closing heavy type telescopic drawers channel etc complete all as per approved shop drawing and as directed. Note :- i) Fittings & fixtures shall be deemed to be included in rate quoted by the tenderer. ii) The measurement for payment shall be based on the superficial area of the modular kitchen cabinets.

S&F Modular Cabinet Kitchen accessories of Stainless Steel grade-304, 6mm thick rod including :- (i) Perforated Cutlery basket, (ii) Grain trolley, (iii) Thali basket, (iv) Cup & saucer basket, (v) Glass basket, (vi) Plate basket, (vii) Premium magic corner (viii) Oil Pull out Tray ( Triple basket layer) , (ix) Dust bin, (x) Cleaning kit rack of size as per site requirement all specified and directed.

M&L for 18 mm thick wood plastic composites (WPC) board, 100% solid with density not less than 650 Kg per cubic meter , both side white finished laminated for exposed/external surface , fixed with screws fitted under or above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc complete all as specified and directed. Note : (a) Pattern & design of WPC board to be decided by GE. (b) Items like cupboard knobs, stainless steel channel, CP plate clip hinges to be paid in extra.

S&F brass chromium plated tubular hanger rod 20 mm dia with suitable brackets complete all as specified and as directed.

S&F 25 mm dia SS curtain rods AISI 304 (minimum 1.6 mm thick sheet) fancy type, including SS bracket and SS side bulb decorative type complete for doors and windows as required complete all as specified and as directed.

Cutting of shrubs/bushes and small plants/vegetation including cutting of trunk n.exc 30cm girth and branches and digging out roots from floor or roofs and walls of up to four storied bldg and making good the dismantled portion in cement mortar 1:3 to match the existing surfaces complete all as specified and as directed.

S&F 100 mm size butt hinges stainless steel of SS 304 grade complete all as specified and as directed.

S&F 300 mm long, stainless steel of SS 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clipss of sheet, cast or extruded sections and fixing bolts and fixed etc complete all as specified and as directed.

S&F stainless steel of SS 304 grade barrel tower bolt 200 mm long, extruded section, etc complete all as specified and as directed.

S&F stainless steel of SS 304 grade handle of size 200mm size long etc. complete all as specified and as directed.

M/S Parmod Johar (BID ID -3420288)

H S KALSI AND BROS (BID ID -3418937)

M/S Davinder Kumar (BID ID -3420801)

Chaudhary Constructions (BID ID -3420053)

M/S Amrit Pal Singh & Sons (BID ID -3417354)

M/S Malik Construction Corporation (BID ID -3420774)

M/S.M.S.Devi.Const.Co (BID ID -3418618)

A R S CONSTRUCTION CO (BID ID -3420625)