Miscellaneous repairs for Civil and PH work in Residential and non-residential buildings under TTM-II unit at Anshaktinagar, Mumbai

Amount

PART I : CIVIL WORKS

PART II - PUBLIC HEALTH WORKS

Part III : Rebated items

Description of Work / Item(s)

Amount

PART I : CIVIL WORKS

Plain cement concrete using graded stone aggregate of 20mm max. size including consolidation, finishing, curing, cost of form work, shuttering, centering etc. complete all as per specification & as directed by the Engineer-in-Charge.

Brick work at all levels & location using Ready mix cement mortar 1:4 using well burnt locally available bricks of approved quality including scaffolding, raking out joints above ground level simultaneous pointing below ground level, curing, scaffolding,etc. complete all as per specifications & as directed by the Engineer-in-Charge.

a) In foundation & plinth, drain walls, chambers etc.

b) In super structure at all floors and levels.

Half brick masonry using well burnt locally available bricks of approved quality & using Ready mix cement mortar in 1:4 at all floors and levels walls without stiffeners including form work, scaffolding, raking out joints, curing, etc. complete all as per specifications & as directed by the Engineer-in-Charge.

a) In partition walls without stiffeners.

Random rubble masonry using spotless black trap or approved locally available stone using Ready mix cement mortar 1:4 including raking out joints, scaffolding, simultaneous flush pointing using through bond stones at every 900 mm in horizontal & vertical courses of each layer, including AC pipe 50mm dia weep hole at 1.5m c/c in horizontal & in vertical, curing,scaffolding etc. complete all as directed by the Engineer-in-Charge. Rubble stone supplied by the contractor

a) In foundation & ground level upto plinth.

b) In super structure.

Cement pointing to stone work using ready mix cement mortar 1:3, including rakingout joints, pointing neatly and finishing the joints as specified below including curing, scaffolding etc. complete all as directed by the Engineer-in-Charge.

a) Raised and cut pointing.

Providing & laying rubble stone soling using spotless stones of consolidated thickness as specified below with stones vertically handset interstices packed with smaller stone chips, binding with murrum/crushed sand, watering, consolidating & finishing to required levels etc. complete all as directed by the Engineer-in-Charge. Rubble stone supplied by the contractor

a) 150 mm thick

b) 230 mm thick

Providing & laying stone pitching 230 mm thick using locally available spotless black rubble stone of approved quality including supply of stones preparation of surface, setting the stones to proper line, level or slope etc. grouting the joints in stone pitching using ready mix cement mortar 1:4 & pointing the surface with the same mortar etc complete all as directedby the Engineer-in-Charge.

Providing Indian patent stone flooring 40mm thick at all floors & levels, in cement concrete 1:2:4 using graded stone aggregate of 10 mm max. size laid to proper level or slope in alternate bays in panels of required sizes, finished smooth including providing glass dividing strips of size 25 x 3 mm wherever required, curing, including removing carefully existing damaged/ worn out flooring and disposing off debris out side colony etc. complete all as per specifications & as directed by the Engineer-in-Charge.

a) 50 mm thick

Providing and laying Kota stone flooring / dado/ skirting at all floors & levels using 25 mm thick hand cut machine polished kotah stone slabs laid over cement mortar bedding/ backing as specified below, close jointed & pointed with matching slurry of cement finished to levels, slope or plumb, curing including removing carefully existing damaged/ worn out flooring and dado & disposing off debris out side colony etc. complete all as per specifications & as directed by the Engineer-in-Charge.

a) In flooring using Ready mix cement mortar 1:4, 20mm thick bedding

b) In dado / skirting laid over Ready mix cement mortar 1:3 backing 12 mm thick

Providing and laying of Kotah stone for stair treads with 3 line anti skid grooves and nosing at all floors & levels using minimum 25 mm thick machine cut machine polished kotah stone slabs laid over 1:4 ready mix cement mortar bedding including curing hand polishing removing old damaged/ worn out tread and disposing off debris within colony etc., all complete as per specification and as directed by Engineer-in-Charge.

Providing and laying of Kotah stone 20 mm thick risers of approved size and laid over ready mix Cement moratr 1:4 backing of 12 mm thick at all level and floors including cutting to required size, curing, removing of old damaged /worn out risers and disposing off debries within colony all as directed by Engineer-in-Charge.

Providing and fixing of machine cut and both side polished minimum 35 mm thick Cuddapah stone for shelves of cup board including removing of old damaged wooden shelves and making Nitches all the three sides of cup board very carefully and fixing cuddapah with cement mortar and re-instaling the surrounding as per existing including disposal of debries within colony all as directed by Engineer-in-Charge.

Providing & fixing 6 mm thick A.C.sheet in any type of work as directed at all floors & locations including fixing the sheet to existing wooden / M.S. / aluminium frame work with necessary screws, forming grooves of required sizes, making necessary openings / cut outs around electrical fixtures, A.C. grills & trap doors incase of false ceiling, fixing the sheets to correct line & level, including cost of screws, wastage in cutting etc. including removing existing damaged asbestos cement sheet and disposing off debris out side colony , if any etc. complete all as directed by theEngineer-in-Charge.

a)6mm thick corrugated/semi corrugated sheet/ Plain A.C.Sheet/Aluminium frame

Providing and fixing second class teak wood in frames of required sections for doors, windows, ventilators, clear storey window, partition, railing, battens & rafters etc.wrought framed and fixed in position including providing and fixing M.S. hold fasts of size 200 x 30 x 3 mm embedded in concrete block of P.C.C. 1:3:6 and labour for fixing frame in position including applying one coat of approved wood primer & two coats of synthetic enamel paint to the exposed surfaces and two coats of bituminous paint to the surfaces of frames in contact with masonry/ concrete etc. including removing the old damaged frames transporting to Deptt. Stores and making the adjacent plaster good to match with existing surfaces, etc. complete all as directed by the Engineer-in-Charge.

Repairs to the existing doors frame of bath, w.c., bed, door etc. by replacing part of the frame with 2nd class teak wood at site of work by: i) Cutting of the damaged/ decayed portion of the door frame without disturbing/ removing of the existing frame. ii) Providing wood with 2nd class teak wood as per the existing frame for repairing of the damaged/ decayed portion of the frame including making lap joints for jointing the new wood with old wood work by fixing necessary screws and synthetic adhesive etc. complete. iii) Fixing the repaired door frame in position with embedding the frame upto 50mm depth in the floor and fixing coach screws to the wall including breaking of the floor for making pocket, applying two coats of bituminous paint to the surfaces of frames in contact with masonry/ concrete, repairing floor with P.C.C 1:2:4, finishing including two coats of synthetic enamel paint over one coat of primer & disposing off debris out side colony etc. complete all as directed by the Engineer-in-Charge.

Providing and fixing second class C.P. teak wood of required sizes and sections for repairing the styles & rails & battens of panelled and battened door shutters of various flats at all floors, including carefully removing the existing door shutters & removing with fittings & fixtures, damaged / decayed teak wood rail/ styles/ battens and plywood panel of shutters, cutting, plaining & jointing the wood, providing and fixing necessary screws and glueing the lap joints with synthetic adhesive fevicol or equivalent, plaining & finishing the new wood work to match with old work in proper line and level including cost of fixing the door shutters with all fittings & fixtures with one coat synthetic enamel paint over one coat of primer on new work and one coat of paint over entire surfaces of shutters etc. disposing of debris out side colony etc. complete all as directed by the Engineer-in-Charge.

a) Teak wood

b) 12mm thick marine ply.

Providing & fixing approved quality block board of Anchor / Mysore/ Kitply or equivalent approved make in following thickness as per relevant IS, including cutting to required sizes and fixing the same with necessary nails/ screws/ adhesives in partitions, cupboard shelves, kitchen cabinets etc. at all floors & locations including, providing and fixing 6 mm thick teak wood beading to all exposed edges of block board including cost of nails, s.s.screws, adhesive, wastage in cutting,transportation etc. including cost of fixing the fittings, painting the surfaces with two coats of synthetic enamel paint over a coat of primer etc. including removing old shutter/ shelves and transporting to deptt. Stores, complete all as directed by the Engineer-in-Charge.

a) 20 mm thick block board shutter including making necessary rebate for double pannel, providing & fixing SS piano hinges 35mm wide ( for cupboard shutter ) Including all fixtures & fitting

b) 25 mm thick block board shelves.

Providing and fixing C.P. teak wood moulded beading (architrave) of sizes 40 mm x 20 mm. around door & window frames at all floors & locations with necessary screws including two coats of painting with one coat of approved primer including cost of screws, wastages in cutting, transportation etc. including removing the old damaged beading and disposing the same complete all as directed by the Engineer-in-Charge.

Providing & fixing ordinary plain/ frosted/ Bajara sheet glass of approved make of following thickness in various sizes as required at site, fixing to windows / louvers, partitions, vision panels, doors etc. using first class oil puttyof approved quality and make including supplying & fixing glazing pins, teak wood or aluminium beading with necessary screws, nails etc. at all floors & locations including cutting the glass to required size, removing the existing broken/ damaged glass panes from windows/ doors/ partitions etc.along with its old oil putty, beading etc. and disposing off the un-serviceable material out side colony including wastage in cutting, transportation etc. complete all as directed by the Engineer-in-charge.

a) 4 mm thick Plain sheet glass.

b) 4 mm thick Bajra / frosted sheet glass.

c) 5 mm thick plain glass with EPDM gasket for aluminium windows

Supplying & fixing in position 35 mm/ 40mm thick of solid core block board flush door shutters with commercial ply on both sides conforming to IS with external type teak wood lipping of section 35 x 20 mm/ 38 x 20 mm.. alround, fixing shutters in position to pressed steel door frames/ wooden frames at all floors by cutting/ planning if necessary, including supplying & fixing heavy duty MS oxidised hinges including cost of fixing the fittings, painting the shutters all over with two coats of synthetic enamel paint of approved make & colour over one coat of approved primer etc. including removing the old damaged shutter and transporting to Deptt. stores all as per specifications, & as directed by the Engineer-in-charge .

a) For door 35 mm thick

b) for door 40 mm thick

Providing and fixing in position 2nd class C.P. teak wood panelled door shutters of 35 mm thicknes, styles, top & other rails 100 mm wide, lock and bottom rails 175 mm - 200mm wide, with treated under vacum pressure and kiln seasoned secondary species timber with insert panles of 12 mm thick marine plywood inlcuding supplying & fixing heavy duty MS oxidized hinges including painting the shutters all over with two coats of synthetic enamel paint of approved make & colour over one coat of approved primer etc. including cost of fixing the fittings, removing the old damaged shutter and transporting to Deptt. stores all as per specifications & as directed by the Engineer-in-charge.

Providing and fixing Night latch Full set with 7 levers, consist of latch assembly, safty latch, Round lock, Retainer plate, Dead lock suitable for doors of 35-40 mm thick, with 3 keys in orginal, inside opening door with safety like brass lever locking mechanism screws required, similar to M/s. Godrej make ( Cat No. 8261) or approved equivalent having same shape, size and dimensions including removing the existing old & damaged lock and submitting the same to the deptt. store etc. complete all as directed by the Engineer-in-charge

Providing & fixing Mortice lock with brass parts and body with 6 levers,of Godrej/ Everite make or other approved equivalent with stainless steel duplicate keys and pair of detachable, pressure diecast chromium plated handle with chromium plated brass screws for left hand/right hand and for single leaf shutter of 30mm to 50 mm thickness with brass socket plate. (Exact number for left, right and double shutter shall be ascertained based on site requirement.) etc. complete as per manufacturer specification and as directed by EIC

a) Mortice lock with SS handle on both sides of shutter.

a) Godrej make model no. 7117 or equivalent with SS handle on both sides of shutter.

Providing and fixing Godrej or other equivalent multipurpose lock for doors of shelves/nitches/cupboards/cabinets with stainless steel duplicate keys including removing old non functioning existing lock and depositing to deptt. Stores, etc complete all as per specification and as directed by the E-I-Charge.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315 ( Make of Hardwyn or Dorma), having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of removing the existing shuter and refixing the same, cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate including removing old non functioning existing floor spring and depositing to deptt. Stores etc. complete as per the direction of Engineer-in-Charge.

Providing & fixing Hydraulic door closure conforming to IS:3564 of heavy duty (as per approved make & design) with fittings and fixtures, necessary screws/bolts and other accessories including removing the existing old & damaged door closure and submitting the same to the deptt. store etc. complete as per manufacturer specification and as directed by EIC

a) Hydraulic door closure of Everite or equivalent approved (Right/ Left type)

Supplying and fixing following type of miscellaneous fittings, fixtures and fastenings of approved quality Stainless steel fittings and fixtures of M/s Shalimar hardware or approved equivalent along with necessary CP brass screws,bolts, nuts, washers and other standard accessories as per approved sample etc. complete all as directed by the Engineer-in-charge

a) Heavy duty SS 304 butt hinges of size 125mm X 76mm X 2.8 mm

a) Heavy duty SS 304 butt hinges of size 75mm X 50mm X 1.7 mm

Heavy quality magic eye / door viewer of brass body, having minimum 180 degree wide angle lens suitable for flush door of thickness 35mm to 50 mm, total length closed condition 40 mm, outside dia 25 mm, mounting diameter 14 mm having full thread for length adjustment

SS Aldrop(SS-304) 250 mm long , 16 mm dia Barrel. with extra locking arrangement of M/s Shalimar (ISI marked)

Heavy duty Magnetic Ball catch for cupboard and cabinets of approved sample

SS Heavy duty Harsp stable 150 mm long of approved sample (For locking arrengement)

Heavy duty SS 304 Piano hinges 19 mm x 20 Gauge.

Supplying & fixing heavy duty superior quality matt finished anodised (anodic coating not less than Grade AC10 as per IS 1868) ISI marked aluminium fittings and fixtures and fasteners along with necessary CP screws, bolts, nuts, washers etc. as per approved makes etc.complete all as directed by the Engineer-in-charge Note: A sample of each material listed above should be got approved by Engineer-in-Charge before supply.

Bow Handle 100 mm. long with back plate, ' D ' section.

Tower bolt 200 mm long with 10 mm dia barrel

Tower bolt 150 mm long with 10 mm dia barrel

Superior Quality Aluminium door stopper Floor type with heavy quality rubber bush fixed with screw, complete set. The weight of aluminium door stopper without rubber bush and screw shall not be less than 25 gms each.

Baby latch 75 mm long with 10 mm dia barrel

Aluminium door Latch/Tadi having sixe 250 mm x 60 mm x 40 mm with hole for locking arrangerment of approved sample

Heavy duty 100 mm long concealed sliding window zinc body lock (Star lock or approved equivalent)

Heavy duty 150 mm long concealed sliding window zinc body lock with L and Key (Star lock or approved equivalent)

Heavy duty 200 mm long Domal series concealed sliding window zinc body lock with L and key (Star lock or approved equivalent)

Heavy duty 250 mm long Domal series concealed sliding window zinc body lock with L and key (Star lock or approved equivalent)

Heavy Quality PVC roller for alluminum sliding windows

EPDM Gasket for existing Aluminium window.

Cement plastering using factory manufactured pre mix/ready mix mortar in CM 1:4 of 'Roofit Mix'of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd or other approved equivalent make, having minimum composition of C:S :: 1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechnical mixing with water in a metalic tray only to make good consistency as per the specification of the Manufacturer and applied on internal wall and ceiling finished smooth with POP over brick walls or concrete surfaces at all floors and levels, including membrane curing by applying one coat of factory made curing compound Resikure of M/s Anuvi Chemicals, Concure of M/s fosroc, Dr. Fixit curing compound or other equivalent over repaired surfaces as per manufacturer's specification and removing existing damaged/ worn out plastering and disposing off debris out side colony etc. complete all as per specifications and as directed by Enginner-in-charge.

a) 12 mm thick

b) 15 mm thick.

Sand faced cement plaster 20 mm thick in CM 1:4, two coats using factory manufactured pre mix/ready mix of 'Roofit Mix'of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd or other approved equivalent make, having minimum composition of C:S :: 1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechnical mixing with water in a metalic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces with base coat of 12 mm thick and finishing coat of 8 mm thick final rendering,including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required, including cleaning the surfaces, including membrane curing by applying one coat of factory made curing compound Resikure of M/s Anuvi Chemicals, Concure of M/s fosroc, Dr. Fixit curing compound or other equivalent over repaired surfaces as per manufacturer's specification etc. including removing existing damaged/ worn out plastering and disposing off debris outside colony etc. complete all as per specifications & as directed by the Engineer-in-charge. NOTE:1.The contractor must take full precautions that original brick work is not damaged while dismantling of plaster. Incase of any damage the same shall be made good with 22g chickenwire mesh at his own cost . No separate payment for any additional thickness of plaster if any will be made. Contractor must visit site and acquiant himself with the condition of building.

Pressure grouting through RCC slab / brick masonry by drilling hole in RCC slab to required depth without causing any damaged to reinforcement, inserting ½” dia PVC pipe in hole securing the hole sides with mortar 1:2, pressure grouting with cement slurry mixed with approved water proofing compound @ 2% by weight of cement to required pressure, continuing the pressure grouting till the flow of cement slurry stops, removing the PVC pipe, sealing the hole with cement mortar 1:1, scaffolding etc. complete all as directed by the Engineer – in – Charge.

White washing for ceiling & walls of rooms and staircases in two coats on old works with lime of approved quality by adding blue and glue in required quantity including scaffolding, scrapping, wherever required,cleaning the surface with sand paper and fibre broom and filling the cracks, holes, with approved putty and making even surfaces etc. complete as per specifications including cleaning of floors, doors, windows etc. as directed by the Engineer-in-Charge.

Repainting of old painted surfaces with two coats of Oil bound distemper of approved make & shade over two coats of approved primer consist of thoroughly scrapping oil bound distemper / white wash surface, applying a coat of approved cement primer, filling upthe cracks with approved crack filling compound, applying approved stucco putty to entire surface to fill up crevices, mild depression etc. thoroughly scrapping the surface, applying 2nd coat of approved cement primer over putty work , apply two coats of Oil bound distemper paint including necessary covering material and removal of splashing & droppings from floors, walls including scaffolding, ladder as required & disposing of debris within colony etc. complete all as directed by the Engineer-in-Charge.

a) Two coats of synthetic oil bound distemper over one coat of approved cement primer

Repainting of old painted surfaces with two coats of premium quality acrylic emulsion paint of approved make & shade over two coats of approved primer consist of thoroughly scrapping oil bound distemper /acrylic emulsion / white wash surface, applying a coat of approved cement primer, filling upthe cracks with approved crack filling compound, applying approved stucco putty to entire surface to fill up crevices, mild depression etc. thoroughly scrapping the surface, applying 2nd coat of approved cement primer carrying out full stucco putty work , apply two coats of acrylic emulsion paint including necessary covering material and removal of splashing & droppings from floors, walls including scaffolding, ladder as required & disposing of debris within colony etc. complete all as directed by the Engineer-in-Charge.

a) Two coats of acrylic emulsion paint over one coat of approved cement primer

Repainting of old painted surfaces with two coats Flat oil paint of approved shade and make over two coats of approved cement primer consist of thoroughly scrapping of all types of old painted surfaces , applying a coat of approved cement primer, filling upthe cracks with approved crack filling compound, applying approved stucco putty to entire surface to fill up crevices, mild depression etc. thoroughly scrapping the surface, applying 2nd coat of approved cement primer over putty work , apply two coats of Flat oil paint including necessary covering material and removal of splashing & droppings from floors, walls including scaffolding, ladder as required & disposing of debris within colony etc. complete all as directed by the Engineer-in-Charge.

a) Two coats of Flat Oil paint over one coat of approved cement primer

Repainting of old painted surfaces with two coats of Royal luxury emulsion paint of approved shade and make over two coats of approved cement primer which consist of thoroughly scrapping old painted surface, applying a coat of approved cement primer, filling up the cracks with approved crack filling compound, applying stucco putty to entire surface to fill up crevices, mild depression etc.thoroughly scrapping the surface, applying 2 coat of approved cement primer, carrying out putty work wherever required, including necessary covering material and removal of splashings & droppings from floors, walls including scaffolding , ladder as required etc. compelte all as directed by the EIC

a) Two coats of Royal Luxury emulsion paint over one coat of approved cement primer

Painting old wood/steel work with two coats of Synthetic enamel paint of approved shade & make over one coat of primer including preparing surfaces, through scapping of MS work, filling with putty wherever required, scaffolding & cleaning etc. complete all as per specifications & as directed by the Engineer-in-Charge

a) On wooden surfaces with two finishing coat over a coat of woodprimer.

Applying three coats of Touch wood of approved make & tint to obtain finish as required over a coat of wood filler including sand papering, cleaning, filling up holes, cracks & crevices with putty etc. complete to give an uniform shade etc., complete all as per specifications & as directed by the Engineer-in-Charge.

Cutting soling/water bound macadam road portion etc. and stacking the serviceable material and disposing of unserviceable material within colony etc. complete all as per specification & as directed by theEngineer-in-Charge.

Demolishing RCC works by chiseling at all levels including scaffolding,cutting of reinforcement bars by gas cutting, straightening and stackingof steel bars and disposal of unserviceable materials complete all per specification & as directed by theEngineer-in-Charge.

Demolishing brick /stone masonry in cement mortar and plaster at all floors & levels including scaffolding, stacking of serviceable materials & disposing of unserviceable materials etc. complete all as per specification & as directed by the Engineer-in-Charge.

a) Brick/Stone masonary work.

Repairs to damaged RCC structural members at all locations/ floors using polymer modified cementatious mortar, for strengthening the existing RCC structural members using acrylic based polymer and comprising the following operations: Important Notes: 1. Breaking cracked / spalled concrete members along the cracks with plaster, including removing and stacking of all unserviceable material at site,simultaneous transportation and disposed at a location in Anushaktinagar as identified by EIC. complete all as per specifications and as directed by the Engineer-in Charge. 2. Exposing and cleaning the reinforcement thoroughly by light tapping / wire brushing of using strong emery paper and finally by acetone /rust remover of Dr. Fixit / Anuvi chemicals / Fosroc or other eqivalent. 3. Applying a coat of polymer and cement slurry in the ratio 1:1 by volume to the reinforcement bars. 4. Polymer required for the work shall be procured by the Agency from approved Manufacturers Like M/s Astra , M/s Anuvi, M/s Apcotex or other approved equivalent manufacturer confirming to technical requirements as below and the invoices/challans etc to be submitted to EIC for record. Appearance: Milky white Ph- value : 9-10 Specific gravity : 1.055+/-0.005 Solid contents(%w/w)-: 44+/-1 Viscocity at 25 degree C temperature (in sec): 15-20 Testing of the material as per relevant codes at NABL approved third party Lab. is to be done by the Agency for every batch/lot of supply. 5. Bond coat should be applied @ 0.37 ltr./layer/sq.m. 6. Minimum FM of silica sand should be 2.10

a) Building up with polymer modified cementatious mortar for RCC structural members etc. in layers not exceeding 20 mm in a day (proportion – cement 50 Kg. : Silica sand 125 Kg. : polymer liquid 10 ltrs.) with necessary bond coat (polymer : Cement = 1:1 by volume) for tack coat and also for subsequent layers using polymer including curing, covering the flooring /window with tarpaulins or equivalent covering material to avoid deposition of polymer mortar and cleaning of floor / windows thoroughly on completion of repair work etc. complete all as per specifications and as directed by the Engineer-in-charge. Polymer used for this work in KG shall be measured for payment.

Providing & erecting double bamboo scaffolding using minimum 75 mm dia best quality bamboo tied with coir rope & the horizontal & vertical members of the bamboos provided as required at spacing of not more than 900 mm apart both vertically & horizontally including providing cross supports as struts to tie the scaffolding properly to the building for maintenance / repair works of external surfaces of buildings as &when required including providing necessary safety belts to workers,dismantling the scaffolding after repair work is completed including cost of transportation, labour, safety belts etc. complete all as directed by the Engineer-in-Charge. NOTE: The mode of measurement shall be in square metre for the overall portion of external exposed surface area of buildings covered by scaffolding and the said area shall be measured flat. No deductions shall be made for any openings in the surface and the jambs / reveals.

a) Double Scaffolding

Labour charges only for laying stone pitching, 230 mm thick, using stones available from dismantling or dept supply, preparing the surface, setting the stones to proper line, slope, grouting the joints with cement mortar:1:4 and pointing the surfaces with the same mortar, curing, including the cost of cement mortar, etc. including cost of removing the damaged pitching etc. complete all as directed by the Engineer-in-Charge.

Providing and laying at all floors and levels Vitrified tiles of first quality Marbonite of M/S H&R JHONSON (INDIA) Ltd or other equivalent approved make of approved colour, shade, pattern and of thickness as per manufacture's specifications, laid directly over tile, using polymer cum cement based adhesive (Type -II as per IS) manufactured by M/S Roffe construction or M/s Bal Endura chemicals or other approved equivalent in respect of flooring and fixed over 12 mm thick backing using ready mix cement mortar 1:3 in respect of skirting , close jointed and grouted white /colour cement slurry with pigments to match the colour of the tiles, finished to level, line, slope and plumb including cutting of tiles, making openings / cut out where necessary including wastage for odd shape of room and final cleaning of surfaces as required, curing etc. complete all as per specification,relevent IS code & as directed by the EIC.

a) In flooring with tiles of approx. size 600 mm x 600 mm similar to Salt & Pepper (White/Grey)/ Rigato/Athelon of M/s H& R Johnson (I) ltd. Or similar tile of other approved make, laid directly over existing tile using tile on tile polymer cum cement based adhesive.

b) In Dado / skirting with tiles of size 600 x 100 mm similar to Salt & Pepper (White/Grey)/ Rigato/Athelon of M/s H& R Johnson (I) ltd. Or similar laid over 12 mm thick ready mix cement mortar 1:3 backing, jointed with cement slurry & grouted with pigment of matching shade & finishing the top of skirting etc. complete, including dismantling the existing dado/skirting tile and backing cement mortar disposal of debris etc. complete.

Providing & laying at all floors & levels first quality matt finished/non slippery ceramic tiles of minimum thickness as specified by the manufacturer of M/S. H&R JHONSON (INDIA) Ltd. or euqivalent approved make of approved colors, shade and texture in flooring / dado / skirting as per approved pattern. incluidng cost of all materials, including of cutting the tiles to required shape, wastage, pointing the joints with white cement mixed with matching pigments to match the colour of the tiles, finished to line, level, slope & plumb, final cleaning of surface as required, curing , making necessary opening cutouts etc. and including removing existing flooring / dado and disposing of debris complete all as per specifications, relevent IS code & as directed by the Engineer-in-Charge.

a) In flooring with tiles of size 300 x 300 ( approx size ) similar to white / ivory / other approved colour quartze series of M/s H& R Johnson or euqivalent approved make with 20 mm thick 1:4 ready mix Cement mortar bedding.

b) In dado / Skirting with tiles of 300X450mm( approx size) similar to combination of Infinity aqua/red/beach and infinity white of Higlihter series of M/s H&R johnson (India) Limited) fixed over 12 mm thick using 1:4 ready mix cement mortar backing/fixed directly over existing tile with polymer cum cement based adhesive(Type-II) manufactured by roffe construction or M/S Bal Endura chemicals or other approved equivalent, jointed with cement slurry & grouted with pigment of matching shade & finishing the top of skirting/dado etc. complete.

c) In Dado / skirting with tiles of size 300 x 450 mm ( approx size) similar to Digital HD series tile Linea blue/snow white of M/s H&R johnson (India) Limited or euqivalent approved make fixed over 12 mm thick ready mix cement mortar 1:4 backing/ fixed directly over existing tile with polymer cum cement based adhesive(Type-II) manufactured by roffe construction or M/S Bal Endura chemicals or other approved equivalent jointed with cement slurry & grouted with pigment of matching shade & finishing the top of skirting/dado etc. complete.

Supplying & fixing 25 mm thick PVC integral free foam sheet in form of flush finish door shutter, manufactured by M/s. Jain Irrigation Systems Ltd. (Ex-cel sheet) or other equivalent approved make of white colour, solid section, extruded rigid, light weight sheet with fine & homogeneous closed cell structure with smooth, glossy, hard surface finish on both sides including providing recessions for hinges and providing & fixing 3 nos 100 mm heavy duty S.S. hinges and 2 Nos. 100 mm heavy duty aluminium baby latches, 2 nos. of 100 mm Al. Bow handles with back plate and including providing a vision panel opening of size 300 mm X 200 mm including providing and fixing PVC moulded louvers on both faces in the opening of vision panel with ss screws, all edges to be smooth finish with mixture of PVC powder & solvent including removing the damaged shutter and disposing the it to store etc complete all as per specification and as directed by the EIC. Note:- 1) The entire door shall be jointless shutter. 2) The sizes shall be approximately 650 mm x 2000mm, however exact dimensions shall be measured at site before manufacturing.

Supplying & fixing 18 mm thick PVC integral free foam sheet in form of flush finish for double leaf cuboard shutter & frames, manufactured by M/s. Jain Irrigation Systems Ltd. (Ex-cel sheet) of approved colour, solid section, extruded rigid, light weight sheet with fine & homogeneous closed cell structure with smooth, glossy, hard surface finish on both sides all edges to be smooth finish with mixture of PVC powder & solvent etc. including dismantling the existing plywood/ A.C sheet shutters/MS shutters/removing the old damaged wooden shelves/shutter and transporting to Deptt. stores etc including all the fixtures and fittings 2 nos-100 mm Al handle, heavy quality SS piono hinges, 2 nos.magnetic ball catch,150 mm Aluminium Tower bolt, 150 mm SS harsh staple locking arrangement etc. complete all as per specification,drawings and as directed by the Engineer- in- Charge. Note:- 1) The entire door shall be jointless shutter. 2) The sizes shall be approximately 600 mm x 2100mm, however exact dimensions shall be measured at site before manufacturing. 3) The rate is inclusive of making of necessary rebate for locking arrangement and all the required fixtures and fittings as mentioned.

18 mm thick double leaf cupboard shutter including necessary rebate & locking arragement.

Repairing of loose / shaky vitrified tile flooring/ green marble/granite stone frames at all floors and levels using polymer modified cement based tile adhesive manufactured by Roffe Construction – NSA (Non Skid Adhesive) or M/s Bal Endura Chemicals– Gold Star or other approved equivalent. The repairing process will consists of following. (1) Complete checking by tapping of affected flooring area using solid wooden stick. Identifying the affected tiles for repair work. (2) Drilling holes through tiles and widenining of tile joints using cutter as per requirement. (3) Breaking of tiles and removing backing adhesive from original flooring, cleaning etc (If Required). Checking the original flooring by tapping using solid wooden stick and repairing of original flooring by breaking the original mosaic / cement tile flooring and filling with 1:3 cement sand mortar, curing etc complete. (4) Grouting the tile flooring using tile adhesive slurry through drilled holes, widened joints, opening made by tile breaking using trowel etc and by tapping of floor tiles etc. (5) Sealing of drilled holes, widened joints using white cement cleaning of flooring, removal of debris and disposal of debris outside colony. (6). Removing and refixing of Aluminium window/door shutter/MS grill for repairing work. After the repairing works (7) Complete checking by tapping of repaired flooring area using solid wooden stick after 7 days of repairing work in presence of departmental representative. The repaired work shall not make any hollow sound, loose/shaky motion of tiles. The entire repairing work shall be carried out as per direction and instrcutions of engineer-in-charge.

(a) Area of flooring for which grouting of joints and backing mortar done using tile adhesive.

(b) Removing loose / shaky vitrified floor tiles and refixing the same using polymer modified cement based tile adhesive manufactured by Roffe Construction – NSA (Non Skid Adhesive) or M/s Bal Endura Chemicals– Gold star, including removal of loose/shaky tiles cleaning back side of tile and removal of tile adhesive from existing floor area, cleaning etc complete all as per specifications and as directed by the Engineer-In-Charge.

c) Replacement of damaged marble stone with 18 mm thick machine cut and single side machine polished Baroda green marble stone for window cill in stepped form laid over 20 mm thick 1:4 ready mix cement mortar & over lapping of 20 mm shall be fixed with Araldite adhesive with best workmanship including half round moulding & polishing of exposed face etc.providing 75mm long SS screw minimum @600mm c/c complete. all as per drawing, specifications and as directed by the Engineer- in- Charge.

d) Replacement of damaged marble stone with 18 mm thick machine cut and single side machine polished Baroda green marble stone for window jamb & bottom of lintel in single piece laid over 20 mm thick 1:4 ready mix cement mortar including half round moulding & polishing of exposed face etc.providing 75mm long SS screw minimum @600mm c/c complete all as per drg, specifications and as directed by the Engineer- in- Charge.

Providing and fixing in position at all floors, levels/ heights 18mm thick mirror polished natural stones slab for door frame in two overlapping layers one piece full length/ height of approved shade, finished sizes as directed including machine cut/ hand cut, final cleaning, moulding and polishing of all exposed edges, in line, level, plumb and fixing the stone with ready mix cement mortar 1:3, 20mm backing & overlapping of 20mm shall be fixed with Araldite adhesive, with best workmanship, finishing, curing, providing 75mm long SS screw minimum @600mm c/c including removing existing door frame/window frame, shutter & fittings etc. and refixing the same with all in original condition and depositing the damaged one at dept. store etc. complete all as per specifications, drawings & as directed by the Engineer- in- Charge.

a) Jet Black Granite Stone.

b) Baroda Green marble Stone.

Providing & applying asian paint smartcare Damp block white colored coating over wall / concrete surface including cost of removing existing old paint with putty etc., applying one coat of self priming coat of AP smart care damp block (diluted with water in 1:1 ratio) and applying two coats of AP smart care damp block (diluted with water in 3:1 ratio) etc. complete as per specification & as directed by the EIC

Supplying acrylic based chemical waterproofing materials at site, Smartcare Damp Proof of M/s Asian paints/ Dr. Fixit Newcoat of M/s Pidilite/ Brushbond Roof Guard of M/s Fosroc / ShaliCryl® LM HI of M/s STP Limited, all confirming to the manufacturer technical requirements etc. completed as directed by EIC

Supplying, fabricating and fixing in position at all floors Aluminium sliding/top hung/fixed/ adjustable louvered windows & ventilators with rivit joint of specified size, made of integrated bronze anodised matt finished (15micron thick) aluminium section (extruded) , including for making exhaust fan frame work, handles of specified size etc, of approved manufacutres for following types with extruded sections of Jindal / Hindal / Aluminax or other approved equivalent make of approved sections with size and wights as directed for frames and shutters (including wastages if any) confirming to relevant IS specifications with all approved Bronze anodised aluminium fittings and accessories, latching fixture, 2/3 rollers with ball bearing of superior quality all as shown in the drawing including providing and fixing aluminium channel beading/glazing clips fixed with necessary bronze anodised screws, grouting the gap with sealant and including dismantling of existing window frame and shutter, glass and depositing same to dept store etc all complete generally as per drawing, specifications etc, all as directed by EIC.

Providing and fixing structural steel of approved grade of approved manufactures using steel sections such as angles, flat bars, tees, channel, tubes, hollow section etc. of required sizes at all levels and locations including cutting, fabricating, welding, erecting & fixing in posion, necessary scaffolding and including painting one coat Zinc chormate primer and two coats of synthetic enamel paint of approved make and colour on all exposed surfaces etc. compete all as directed by the Engineer-in-charge.

Supplying and fixing in position at all floorsand location stainless steel 304 grade mosquito net made out of 24 guage ,16meshshutters including exaust fan frames etc. ofvarious size and shape fixing with stainlesssteel nuts and bolts to suit the aluminiumframe ( aluminium frame , beading etc. shallbe paid under relevant item) including labour wastage scaffolding etc. all complete as per specification,drawings & as directed by EIC

Providing and fixing adustable M S Tubulor props up to 4.00 M at required locations including breaking loose conrete/plaster, including cost of supporting planks, wooded members etc. as per drawing/ sketch, complete all as directed by the Engineer-in-charge.

Providing assistance to the departmental technician for attending the complaints of various nature on working days/holidays/ beyond office hours viz ,etc in various flats and buildings including neccessary tools and manpower, loading, unloading etc complete all as directed by the Engineer-in- Charge. (Working hours should be 8.30 Hours with 30 minute lunch break)

Supply of un-skilled Labour

Supply of Semi skilled Labour

Labour Charges for cleaning, brooming, washing/mopping the vacant flats including disposing of waste materials including cost of cleaning materials like brooms, detergents/disinfectants etc complete all as directed by the Engineer-in- Charge.

a) Upto Type III C including trasit/efficiency flats

b) Type IV D & Above flats

Labour charges for Removing, dismantling, fabrication & refixing exisiting Aluminium sliding/top hung/fixed/ adjustable louvered windows & ventilators/doors with rivet joint/solid door shutters/MS grill/Cupboard shutter with selves & frames of specified size for repair,refixing & maintenance works such as replacement of rollers, marble cills, jams, EPDM Gasket,wooden shutters,cupboard shuter with selves all complete generally as per specifications , all as directed by EIC. (Rollers, gasket, friction hinges, marble stone, floor springs, hinges etc shall be paid under relevent item.)

Removing & refixing exisiting door shutters in original condition after completion of repairing works of frames including all labours and all the fittings and fixtures etc. complete all as per specifiction and as directed by EIC

Disposal of Surplus earth/debris of all kinds of construction waste material by mechanical transport to near by dumping pits/areas out side department colony/office premises including all lifts, loading, unloading, stakcking, spreading, levelling etc complete as directed by EIC. Notes :1 ) Voids @20% for solids and 50% for rock shall be dedcuted from fully loaded truck measurement to arrive at the net quantity for payment in case of direct measurement is not possible. 2) The cost is inclusive of necessary permisiion from statutory authorities for dumping the debris/excess earth outside department premises.

Providing centring shuttering Form Work using 19 mm PVC film faced plywood to get neat form finish surface for Walls, partitions, paradi and the like including attached pilasters etc.as per drawings, specifications and as directed by the Engineer-in-Charge.

Providing & fixing 18 mm thick & approx 50 to 100 mm wide jet black Granite stone for fins/facia in kitchen platform with moudling in both side including machine cut/ hand cut, final cleaning, moulding and polishing of all exposed edges, in line, level, plumb and fixed with approved adhesive with necessary cement paste, including removing damaged granite patti all per specifications and as directed by the Engineer-in-Charge.

Supplying and fixing in position GI weld mesh of size 50mm*25mm*8 gauge to jalli/ MS angle frame work wherever necessary including cutting to required size & shape, wastage, cost of tools & plants transportation, scaffolding, and including two coats of synthetic enamel paint of approved shade & make over a coat of approved steel primer etc complete all as per specification & as directed by the EIC.

Supplying and fixing in position 3 mm thick corrugated FRP sheets of Ivory/ half white colour on MS frames over service shafts /including providing approved ridge and openable covering /fixed coverings ,all overlaps, mitring, cutting, wastages including providing and fixing necessary 8mm Dia J & L hooks, bolts & nuts and G.I. bitumen washers as per manufacturer's code of practice and cutting the FRP sheet to required size including scaffolding wherever required etc all complete and as per specification and as directed by EIC.

Labour charge for repair and modification to M.S. ladder,M.S Member from ground floor to terrace in Service shaft by cutting and removing the ladder (which are coming above the modified height of shaft) to the required length along with embedded brackets, cutting and removing the M.S. brackets from the dismantled ladder, welding the dismantled M. S. brackets to the remaining end of ladder in shaft, re-embedding the M.S brackets into the masonry, with cement mortar 1:3 mixed with waterproofing compound and finishing the surface neatly etc., including cost of all labours, tools and plants, welding including stacking the unserviceable cut portion of M.S. ladder at directed place etc. complete all as directed by the Engineer-in-Charge.

Providing & applying painting one coat Zinc chormate primer over shop coat of approved anticorrosive primer and two coats of synthetic enamel paint of approved make and colour on existing M.S expose surfaces including scaffolding or cleaning surface etc. complete all as per specifications & as directed by the Engineer-in-charge.

Preventive maintanance of garden Play equipments including quarterly cleaning/oiling/greasing/painting & replacement of damaged parts etc. cost of all labour, material, taxes etc.complete all as per specification and as directed by EIC. Note: 1. Each JOB shall include maintenance of all equipments (Slide + Swing + seasaw) four times annully. 2. Panel recovery of Rs.500 per day per complaint will be levied if not attended within 3 days.

Oiling, greasing & servicing the existing collapsible gates of assorted size including removal of rust by rust removing solution etc. & make the collapsible gate serviceable by doing, oiling, greasing & servicing etc. with a periodically of servicing at an interval of 3 months for one year contract period incluidng maintaining the collapsible gates during the year by attending defective operation, replacing damaged parts wherever required etc. complete all as directed by the Engineer-in-Charge.

Oiling, greasing & servicing of mild steel rolling shutters of assorted size both inside the guides & top hood gear boxetc. complete with a periodicity of 3 months interval for entire year of the contract period incluidng arrending to any defective operation of shutters, wherever required from time to time including cost of all materials, tools, grease, oil etc. required for servicing etc. compelte all as directed by the Engineer-in-Charge.(TTM-I+WSMU=10+3)

Repairing work of Main door MS frames in variious flats including removing & refixing of solid door shutter,replacement of damaged MS frame, welding, painting,hinges fixing including all labour,welder,material etc. complete all as per specfication and as directed by EIC. (MS member required shall be paid under relevant item)

Providing, fixing 1 mm thick of approved qulity and shade Laminate of Forminca/Greenlam/Meriono etc. for Kitchen Cabinate/shelves inclusind all fixing accessories, screws, nail, adhesive, labours, scaffolding including all tools and equipments etc complete as per specficitiona, drawings and as directed by EIC

Description of Work / Item(s)

Amount

PART II - PUBLIC HEALTH WORKS

Providing, laying, jointing, fixing, testing & painting heavy quality (Class 'C') G.I. galvanized pipes as per I.S. 1239-1968 including fittings like elbows, collars, tees, unions, couplings, reducers, enlargers, bends and all other tittings required for the completion except screwed flanges conforming to I.S.1239-1968 & also as per the code of practice of water supply in bldgs. of I.S.2065-1972 inlcuding laying under floors, chasing, in walls, roof slabs and making good the same to the original conditions, including the cost of all jointing materials like hemp yarn, white or red lead, clamps, wooden gutties, screws, cement, sand etc. including removing the old damaged G.I. pipes & handing over to dept. stores, scaffolding, testing the pipes etc. complete all as per specificaton and as directed by the Engineer-in-Charge. NOTE : The measurement shall be taken along the centre line of pipes & fittings or specials but excluding flanges. NOTE : The measurement shall be taken along the centre line of pipes & fittings or specials but excluding flanges.

a) 15 mm n.b.

b) 20 mm n. b.

c) 25 mm n.b.

d) 32 mm n.b.

e) 40 mm n.b.

f) 50 mm n.b.

g) 65 mm n.b.

h) 80 mm n.b.

Providing & fixing C.I. Heavy quality pipes & specials all fittings of required size & shapes, cutting the pipes to required lengths & laying or fixing in position with M.S. clamps & nails 50 mm away from the wall faces jointing the pipes and specials by spun yarn and filling molten pig lead / with cement mortar joint 1:1 with hemp yarn etc. as per I.S. standard practice making holes in walls or floor and making good the same to the original condition, painting 3 coats of anti-corrosive black bitumestic paint, testing the pipe line by smoke test, / rectifying the leakages, if any, including removing the C.I. pipes with fittings and handing over to Deptt. Stores, necessary scaffolding etc.complete all as per specifications and as directed by the Engineer-in-Charge. (A) With cement joint 1:1 with hemp yarn:

a) for 75 mm dia.

b) for 100 mm dia.

Providing & laying salt glazed stone ware pipes and fittings of grade'A' or 'AA' conforming to IS : 651 in trenches for all depths, to correctgrade, levels and elignment including jointing with hemp yarn andcement mortar 1:1 including testing etc. including removing &disposing off debris out side Colony etc. complete as perspecifications and as directed by the Engineer-in-Charge

a) 160 mm dia.

Labour charges only for carefully removing / dismantling the existing G.I. Water supply pipe line in all sizes, along with its existing fittings at all floors and location including cleaning the pipes with thin rod, removing sand particles or miscellaneous other obstructions in pipes and fittings including labour charges for replacing the damaged / unserviceable G.I. Pipes & fittings wherever found necessary including refixing the same in its original position in proper line, level and plumb with necessary specials / fittings making threadings, jointing the pipes and fittings with hemp yarn, white zinc paste, clamping, testing the pipes & fittings for leak proofness and smooth working including returning the defective / unserviceable materials to stores of maintenance Units etc. complete all as per specifications and as directed by the Engineer-in-Charge. NOTE: Necessary materials required for replacement shall be supplied by the deptt. free of cost.

Providing & fixing European water closet conforming to IS 2556 (part II ) with 'P' or 'S' trap wash down pattern European water closet of approved (Cera, hindware/parryware) make in white glazed vitreous of size 460 mm x 330 mm ,including all fixing accessories,white cement & including cost of removing the existing one & disposing of debris out side colony etc complete all as per specifications and as directed by the Engineer-in-Charge.

Providing & fixing approved make Orissa pattern W.C. conforming to IS 2556 ( part-II) comprising of Orissa pattern W.C. with 'P' or 'S' trap in white glazed vitreous china ware of size 580 mm x 400 mm including the cost of removing the existing damaged / broken and making good the surrounding with cement mortar / concrete tiles maching to the existing finish & disposing of debris out side colony etc complete all as per specifications and as directed by the Engineer-in-Charge.

Providing & fixing approved quality wash basin with plain rims in white glazed vitreous chinaware supported on suitable wall brackets and of size mentioned below, including cost of removing the existing wash basin and necessary C.I. brackets shall be provided by the contractor including all the labour charges for fixing the existing fittings such as piller cock, inlet connection, stop cock, wash coupling, bottle trap etc. & disposing of debris out side colony etc complete all as per specifications and as directed by the Engineer-in-Charge.

a) 550 mm x 400 mm.

b) 450 mm x 300 mm.

Providing & fixing approved C.P. brass towel rods of size 600 mm x 20 mm with a pair of C.P. brass brackets, wall flanges ,C.P. brass brackets, etc. fixed to wall with C.P. brass screws, screwed on to rawl plugs etc complete including the cost of removing the existing one & returning to Stores etc complete all as per specifications and as directed by the Engineer-in-Charge.

Providing & fixing heavy quality 15 mm dia inlet connection with unions at the ends plastic pipes with brass unions including the cost of removing the existing one etc complete all as per specifications and as directed by the Engineer-in-Charge.

a) size 600 mm long

b) size 450 mm long

Providing & fixing approved heavy quality solid plastic seat and lid of white shade with C.P. brass pillar hinges conforming to IS 2548 and including cost of removing the existing one depositing to deptt. stores etc complete all as per specifications and as directed by the Engineer-in-Charge,

a) Hollow type of European water closet

Providing and fixing approved quality 10 Ltrs. capacity PVC flushing cistern of SLIMlINE/CERA conforming to relevant IS, with all internal fittings, pull chain etc mounted on brackets including cost of removing the existing one depositing to deptt. stores etc complete all as per specifications and as directed by the Engineer-in-Charge. A) High/Low level cistern

a) P.V.C. cistern conforming to IS

Providing and fixing universal Internal Kit of approved make for PVC flush tank (Syphon set + Ball Cock set+ Button Lever set) that fits most of the standard cisterns/flush tanks/ . The kit consists of a Syphon set the controls the outflow of the water, a ball cock set (adjustable) that controls the water inflow and filling of the tank, a lever set that controls the release of water. Made from heavy duty plastic etc. complete as per manufactures specification and as directed by EIC.

Universal Internal Kit of approved make for Flush tank having single syphon set+ 1ball cock set+1 button Lever set

Universal Internal Kit of approved make for water saving Compact Flush tank (Flush tank+commode) having dual flush valve syphon set+ adjustable 1ball cock set+1 set of push buttom.

Providing and fixing PVC flush pipe Everlas or equivalent of 32 mm dia to a length 2.25 M (approximate) and connecting to the flush tank with proper brass check nut and connecting to the W.C. pan and making leak proof joints of flush and W.C. ends and including removing the existing one etc complete all as per specifications and as directed by the Engineer-in-Charge.

Providing & fixing in position following type CP fittings/ Fixtures/Faucets of 15 mm nominal dia. with ISI mark/ approved make including providing &fixing specials, wall flanges and fixing to concealed/ exposed pipe line with leak proof threaded joints using tephlon tapes, testing the joints hydraulically to a pressure of 10 kg./ sq.cm, rectifying the leakyjoints if any, including removing the existing and depositing to deptt stores etc complete all as per specifications and as directed by the Engineer-in-Charge.

Heavy quality 15 mm n.b. C.P. brass pillar tap of approved make

Heavy quality 15 mm n.b. C.P. brass screw down stop cock of approved make of easy clean variety

32 mm/ 40 mm dia heavy quality C.P. brass waste coupling with plug

C.P. brass bottle trap of 32 mm dia with C.P. brass extension piece & wall flange

Heavy quality 15 mm n.b. C.P. brass bib tap of easy clean variety conforming to IS:781,

Decorative round shaped C.P. brass shower rose of easy clean design of size75mm suitable for fixing on G.I. lines with built-in ball joint for directional changes

Heavy quality Jet spray wall bracket

Providing and fixing in position bevelled or plain edge mirrors made out of best Indian glass 6 mm thick of approved manufacture, mounted on asbestos cement sheet 6 mm thick fixed in position with 4 Nos. C.P. brass screws with detechable C.P. brass caps washers, rawl plugs and incuding removing the existing one and depositing to deptt. stores etc complete all as per specifications and as directed by the Engineer-in-Charge.

a) size 600 x 450 mm.

b) size 450 x 300 mm.

Providing & fixing C.I. Nahani trap of self cleaning design with 75 mm outlet having a minimum water seal of 50 mm with SS Grating on top including necessary 1:2:4 cement concrete for embedding the trap, conforming to IS:3989, including removing the existing one & depositing to deptt stores etc complete all as per specifications and as directed by the Engineer-in-Charge.

Providing and fixing in position heavy pattern screw down gun metal Gate Valve conforming to IS:778 with hand wheels at top including testing for 10 Kg./ Sq.Cm. pressure with clean and potable water with a minimum testing duration of two hours etc including removing old gun metal Gate valve & returning to deptt stores etc complete all as per specifications and as directed by the Engineer in Charge.

a) 15 mm dia.

b) 20 mm n.b.

c) 25 mm n.b.

d) 32 mm n.b.

e) 40 mm n.b.

f) 50 mm n.b.

g) 65 mm n.b.

h)80 mm dia

Providing and Fixing cPVC Ball valve with S.S balls & Specials, if required of approved make suitablefor pipe pressure class, making water proof joints,for pipe pressure class, making water proof joints,ncluding cost of jointing material and cPVCspecials if required, testing the joints etc. completeas per directions of EIC. SDR-11 (IS 15778)-cPVC Ball Valve

15 mm dia.

20 mm dia.

25 mm dia

32 mm dia.

40 mm dia.

50 mm dia.

Providing and fixing in position square mouth UPVC Gully Trap of size 150 x 150 mm square and 110 mm n.b. outlet with grating of approved make embedding the trap in 100mm alround 1:2:4 cement concrete,including construction of brick masonry chamber 300 mm x 300 mm (internal ) upto 600mm depth in 230 mm thick brick masonry, embedding the trap, plastering with cement mortar 1:3, 20 mm thick on inside, outside and all exposed faces, finished with a floating coat of neat cement, providing and fixing precast EVERLAST Composite(FRP/GRP) cover with frame of size 300mm*300mm having point loading capacity of not less than 0.3 tonne as approved including removing the existing gully trap and depositing serviceable material to dept store and disposal of debris inside Anushaktinagar colony at the location identified by EIC etc. complete all as per drawing, specifications etc, all as directed by EIC.

Providing and fixing 32/40mm dia. Heavy quality PVC flexible pipe to existing sinks/wash basins and C.I pipes etc. with necessary threaded coupling etc. complete, fixing and jointing the same using hemp yarn, white leads, clamps, white cement etc. complete all as per specifications and as diectged by the Engineer-in-Charge.

Construction of Inspection Chamber of internal clear dimension 900x600 mm in 230 mm thick brick masonry in C.M. 1:6 over a bed of 150 mm thick 1:4:8 C.C. foundaton, plstering within C.M. 1:4, 20 mm thick on inside, outside, and all exposed surrfaces finished with the floating coat of neat cement 1:2:4 C.C. for benching and channel, finished with neat cement, brick corbelling at top to provide clear opening of 900 mm x 450 mm etc complete including dimantling existing chambers & disposing of debris out side colony (depth of chamber not exceeding 900 mm) all as per specifications and as directed by the Engineer-in-Charge.

Providing and fixing in position precast RCC covers for pits / chambers etc. of 1:1:2 mix. using graded stone aggregate 20 mm maximum size, with MS frame work including form work, compaction, finishing with a coat of neat cement punning for all surfaces, curing and including reinforcement etc complete all as per specifications and as directed by the Engineer-in-Charge. (Necessary Reinforcement & MS work will be paid under relevent item)

Reinforcement with TMT bars of Fe500D grade reinforced cement concrete conforming to IS at all floors & levels including, supplying, cutting, bending, fixing and tying in position with 1.6 mm dia soft drawn annealed binding wire including cost of binding wire, labour and welding of new reinforcement bars with existing reinforcement bars wherever required etc. complete all as per specifications and as directed by the Engineer-in-Charge. Note:- Binding wire required for the work will have to be supplied by the contractor & the same will not be measured for payment.

Supplying and fixing following size PVC-SWR pipes and Fittings for soil, waste,vent and rainwater pipe lines consisting following items of work:- i) Supplying PVC - SWR pipes and fittings conforming to IS 13592 of approved make and standard PVC clamps ( approx. 3.2 mm thick ) and nails or MS galvanised clamps having minimum 3 mm thick for fixing the pipe. ii) Fixing the pipeline vertically to plumb, keeping the pipe barrel 50 mm away from the wall face, using PVC or MS galvanised clamps. iii) Providing and fixing PVC Domed roof outlet (grating ) for RWP & PVC cowl for waste / soil pipe. iv) Jointing the PVC pipes and specials by PVC solvent cement, rubber lubricant with rubber rings or any other approved equivalent method. v) Laying the pipeline below the ground to proper slope and gradient for making connection of soil and vent pipeline ( Vertical stacks ) with inspection chamber or manhole and waste water pipeline with gully trap chamber including the cost of cement mortar, water proofing compound etc., testing the vertical pipeline by smoke test and horizontal pipeline by 600 mm head of water and rectifying the leakages, if any all complete incuding encasing the pipe line using CC 1:3:6 etc. all complete. vi) Cutting or making hole in RCC or brick work and reinstating the surface to it's original condition after passing the pipe with cement mortar / cement concrete etc. by adding approved water proofing compound. PVC - SWR Pipe & Fittings ( TYPE-B ) NOTE: Rate quoted shall be for each item including removal of existing damaged material and depositing to Deptt. Stores / disposing off the debris.

a)32 mm dia

b)40 mm dia

c)50 mm dia

d) 75 mm dia.

e) 110 mm dia

Providing waterproof brick bat coba for filling in the depression of toilets, bathroom etc. as per the specifications of specialised waterproofing agencies and finishing the surface even so as to be suitable to receive the tiles etc. including removing/dismantling existing brick bat with water proof plaster/tiles etc. & disposing off debris out side Colony etc complete all as directed by the Engineer-in-Charge.

Providing cement based waterproofing treatment to the sunken etc. giving injections to the concrete surface as required with cement and approved waterproofing compound solution to fill all inherent holes, voids, honey-combs etc. in the concrete, applying waterproof plaster of about 25 mm thick for the floor areas of the depression and about 18 mm on the side walls of the depression and continue the vertical treatment on the walls above the proposed floor finish upto a height of 600 mm with surface suitable and even to receive tiles, including applying one coat of zycosil coating with ( 1 zycoil : 20 Water ) solution testing the treatment for water tightness by impounding water for 7 days etc. complete all as directed by the Engineer-in-Charge. Note : i) The contractor shall furnish guarantee bond on appropriate stamp paper in the proforma as per Appendix 'D' for the entire waterproofing treatment for maintaining the surroundings and under side surfaces of the waterproofing treatment in bone dry condition for 10 years. During the guarantgee period the contractor shall attend all leakages,defects etc. if noticed, free of cost, starting the work of checking up and rectification within a week's time from the date of intimation about suchleakages/ defects. ii) The measurement for payment shall be actual area covered by the treatment.iii) The waterproof brick bat coba filling coming over the waterproof plaster shall be measured in Cu.M. separately and the cost of the same is not included in this item.

Labour charges only for carefully removing of all type of chokages as & when required at various floor levels from kitchen sink, wash basins, bathrooms, water closets, gully trap chambers ,internal inspection chambers & drain pipes in service shafts of residential & non- residential building viz low rise building having Ground + 1 & upto Ground + 4 upper floors incluinding cleaning existing ACC & waste soil pipes stone ware pipe lead/CP brass 'P' trap and bottal traps etc. of the above sanitary fixtures by the rodding or other suitable means like mechanical choke remover machine with KIWI Drainage chemicals hand pumps and all other cost for incidential charges to complete the job, whenever found necessary including throroughly removing the dirt, seware sludge and miscellaneous rubbish in and around the inspection gully trap chambers & disposing at the same away from building within a lead of 150 m or to the nearest disposal ground including washing the floor aeras in service shafts with phenyl water all inclusive of labour ,tools, phenyl etc. complete all as directed by the Engineer-in-Charge. Note:- 1) The contractor shall make his own arrangement for opeining & closing of plugs of cleaning eyes for waste soil pipes, lead trap etc. at his own cost. 2) The chokages complaints shall be attend proparly by the contractor by arranging sufficient number of labour commensurate with the magnitude of work involved. The labour shall be made available daily for full day for his working days a week during the working hours of the maintenance office.

a) for Chokes in bath/WC/ Kitchen sink/ wash basin/ nahani Trap

b) for Chokes in gully trap

c) for Chokes in inspection chambers

d) for Chokes in Manhole.

Providing & fixing on Exposed or concealed surfaces the following dia Chlorinated Polyvinyl Chloride (C-PVC) pipe of specified class of M/s. SUREME / PRINCE or other approved equivalent consisting following items of work:- i) Supplying & fixing C-PVC pipes, including necessary all fittings conforming to IS 15778 ii) Laying and fixing the pipe and specials on exposed surfaces to correct line, level and plumb for water supply line, overflow and vent using M.S. nails/screws, rawl plugs, wooden gutties and branded clamps of Supreme/Prince make to the pipeline as per the site requirement. iii) Testing the pipe line to a hydraulic pressure as per manufacturers cataglouge for leak proof joint or as per relavant code iv) Making leak proof threaded / solvent joints. including cutting the pipe, Joint preparartion, cleaning, marking, application of solvent, assembling, curing etc. and the cost of jointing cement solvent materials. v) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition. proof joints. vi) Providing and fixing C-PVC jointable / threaded fittings such as Union, Nipples, Bendes, Elbows, Tees, Reducers, End caps, Couplers, Adaptors, Saddles, Plugs, Tank connectors, Expansion loops, Bypass bends, etc vii) including removing existing GI pipe line/cPVC/uPVC/PVC with fittings and specials etc. Note:- All brass threaded elbows and fittings shall be with additional support type of M/s. Prine, Supreme or other equivalent approved by EIC including necessary fixing arrangement such as screws, plug etc complete. ( Mode measurement :- The measurement shall per Unit RM length of pipe line laid or fixed. The measurement shall be taken along centre line of pipe. No measurement shall be recorded saperately for fittings etc. ) SDR 11 Pipes and Fittings

a) 15 mm n.b

b) 20 mm n.b

c) 25 mm n.b

d) 32 mm n.b

e) 40 mm n.b

f) 50 mm n.b

Supplying and fixing heavy Quality CP brass hand held jet spray (Health Faucet) of approved make and sample for ablution (minimum weight of 250 grams for CP brass jet spray only) without pipe & wall bracket etc.

Providing & fixing C.P. metal wrapped- PVC flexible 15 mm dia pipe-1.00m long with one end check nut & other end 32mm long socket with washers for connecting the hand spary of make BPI or equivalent (wt. not less then 250 gms) , wall bracket etc. complete all as per specifications & as directed by the Engineer-in-Charge.

Providing, hoisting and installing at required elevation Rotational moulded polyethylene (as per IS10146) cylindrical vertical storage tanks with BIS mark confirming to IS 12701 of Sintex make and of below said capacity with suitable municipal approved cover at top with proper locking arrangement including the cost of hoisting the tank carefully to the required elevation without causing any damage, labour charges for making required number of holes for inlet, required number of outlets to each tank, required number of vent pipe outlets to each tank and overflow outlets in the Sintextank with out causing any damage to Sintex tank ,including cost of providing all required CPVC/ GI/ UPVC/ PPR specials, fixtures, fittings, tank connectors,adopters, union etc., providing and fixing requirednumbers of flexible PVC pipe/ polymer reinforced thermoplastic hoses suitable for Suction/ delivery linesof agricultural pumps confirming to IS 15265 : 2003 of Kissan Brand Heavy Grade suction/ delivery hose to inlets & outlets having diameter suitable for connecting to 50mm nominal size CPVC/ 50 mm n.b GI water supplyline, having length (flexible pipe) of up to 1.0 Metre/ required shorter length in respect of each inlet & outlet connection of tank including the cost of providing appropriate S.S clamps,CPVC/ GI/ UPVC/ PPRrequired adopters/ fittings/ fixtures/ specials forconnecting flexible hose with G.I/ CPVC/ PPR pipes,including providing CPVC/ GI/ UPVC/ PPR union on both sides of flexible pipe for easy installation and for easy removal for maintenance without causing any damage to Sintex tank., ensuring all joints are completely leak proof , providing full support to the base of flexible pipe/ hose with appropriate arrangement to support the entire length & base of flexible pipe to avoid any sagging of flexible pipe and to avoid any damage to Sintex tank due to sagging of flexible pipe (The work of providing appropriate supporting arrangement for the entire length/ base of flexible pipe will be measured paid under the relevant other item of contract), including cost of providing required number of CPVC tank connector for over flow pipe & vent pipe suitable for connecting with 50 mm nominal size CPVC pipe etc complete all as directed by the Engineer in charge. (The CPVC/ GI pipes along with specials, fittings and fixtures provided will be measured in length (along the centre line of pipe line )under the scope of other relevent items. However this item includes the cost of providing flexible pipes and the additional cost if any involved in providing specials, fixures and fittings in respect of whole of this item)

Sintex tank capacity of 3000 litres

Providing & fixing in position approved quality CP brass stop cock/angle cock/Bib tap / Sink tap etc. of 15 mm nominal dia. with IS mark / approved make of following type including providing & fixing GI specials ,wall flanges and fixing to concealed / exposed G.I.pipe line with leak proof threaded joints using spun yarn, white zinc etc., testing the joints, rectifying the leaky joints, if any, including cleaning etc. complete all as per specifications and as directed by Engineer- in- Charge.

a) C.P brass Bib tap with wall flange, .similar to 'Continental series ' of ' JAQUAR' Cat. No. 047

b) C.P brass long body Bib tap 2 in 1 similar to . FLORENTINE Series' of ' JAQUAR' cat. No. 5041 including providing and 'fixing Health faucet with 1.0 mt long flexible tube and wall hook( JAQUAR make Cat. No. 573).

Angular Stop Cock with wall Flange similar to 'Florentine series' of '' JAQUAR' cat. No. FLR-5053 N.

C.P brass Sink Tap with swinging casted Spout (wall mounted type ) similar to 'Florentine series' of ' JAQUAR' Cat. No. FLR-5347 ND.

a) C.P. brass Pillar Cock 15 mm size auto closing system with Aerator 'PRESSMATIC' as per'Jaquar' cat. PRS- 031.

a) C.P.brass 15 mm size auto closing Urinal Flush valve with wall flange Pressmatic as per JaJaquar cat. No. PRS-077.

CP brass Coat Hook of Jaguar Cat. No.ACN-1161N

Providing and fixing Kitchen sink waste coupling of approved make with choke-stop strainer has broader outlets with 1½ - inch diameter - with ISI mark including removing the existing & depositing to deptt stores etc complete all as per specifications and as directed by the Engineer-in-Charge.

Providing and fixing 40/50mm dia CP brass coupling with approved quality CP brass Mosquito proof jali including providing Galavanised MS bend and any other GI speacials if required for fixing the coupling, jointing materails etc complete as specified and directed by EIC.

Providing & fixing approved quality wash basin of M/s Cera Sanitary ware or other approved equivalant in white glazed vitreous chinaware supported on suitable wall brackets and of size mentioned below, including cost of removing the existing wash basin and fittings such as piller cock, inlet connection, stop cock, waste coupling, bottle trap etc.depositing serviceable material at dept store & disposing of debris out side colony etc complete all as per specifications and as directed by the Engineer-in-Charge.

i) 550 mm x 400 mm ( Approx Size ) CORNET Cat No. 1008

ii) 450 mm x 350 mm. ( Approx Size ) CANON Cat No. 1012

iii)Under counter oval shape wash basin of size 560X410

Providing & fixing approved quality One piece EWC with Calibre premium Seat cover with Twin flushing system of M/s Cera Sanitary ware or other approved equivalant in Snow white glazed vitreous chinaware including all fixing accessories,white cement & including cost of removing the existing one & disposing of debris out side colony etc complete all as per specifications and as directed by the Engineer-in-Charge.

Calibre 660x360x760mm P Trap One Piece EWC with Calibre Premium Seat Cover and Twin Flush fitting Snow White (Cera Cat no.S1013147 Or Equivalent)

Carrying out repairing work for existing damaged / rusted/ leaking GI pipe wall piece ( of dia 32/40 mm at outlet point) of RCC over head water tank at all levels & location as per procedure given below including providing, supplying, fixing all required labour, tools, plant, machinery, scaffolding, cutting wastage, water testing, checking etc complete all as per best practice, specifications and as directed by the Engineer-In-Charge. (1) Providing temporary water supply connection (from inlet and / or tank oulet or both) for domestic / flushing outlet line using heavy quality flexible hose pipe (of dia 32/40 mm) with clamps & all required fittings, material. Draining out the all water stored in domestic / flushing water tank as required. (2) Disconnecting the existing damaged / rusted / leaking GI water pipe line of outlet of domestic / flushing tank. Carefully removing damaged wall pipece with wall plate etc completely. Cleaning the existing RCC water tank wall hole and filling & plugging with micro concrete to achieve complete water tightness. Finishing and repairing using ready mix cement mortar from inside & outside of tank at nearby area of damaged old outlet. (3) Providing and making cores in wall of over head RCC wall tank having dia suitable for providing & fixing heavy quality GI pipe wall piece of sleeve (of 32/40 mm) using electric operated core cutting machine and including providing & fixing heavy quality GI pipe wall piece / sleeve of dia 32/ 40 mm & length 600 mm (approx) for outlet / scour pipe including making outer surface of pipe rough and filling surrounding of new wall piece with arladite, micro concrete, polymer mortar etc to achieve complete water tightness. (4) After setting of mortar in abandoned hole & surrounding of new core, filling the water in over head water tank for testing leak proof ness for seven day. After ensuring complete water tightness, making connection for water supply from newly fixed outlet pipe incuding providing & fixing all required material, labour, fittings, wastage, scaffolding, fittings, specials etc, disconnection of temporary water supply & making water supply from new outlet pipe etc complete all as per specification and as directed by the Engineer-In-Charge.

Providing chemical based water proofing treatment of approved make ( Indofil/ Pidilite / Asian) over bath/ WC brick bat coba & other locations as per the following procedure: a) Cleaning completely the existing surafce to remove all dirt with wire metal brush. b) Applying a primer coat of water proofing compound (diluted with clean water as per recommendations of manufacturer) over the entire area to be treated including filling up of cracks, if any with CM-1:3 mixed with waterproofing compound. c) Applying a first coat with water proofing compound with cement in 1:1 ratio. d) Providing and spreading of polycon based fibrous water proofing net for entire area including lapping as per manufacturer's specifications immediately after applying first coat and curing. e) Applying second coat with water proofing compond with cement in 1:1 ratio over the polycon based fibrous net. f) Applying top coat with undiluated water proofing compound. Note : a) The contractor shall furnish guarantee bond on appropriate stamp paper in the proforma as per Section 10 (iii) page No.74 of CCC-2008 for the entire waterproofing treatment for maintaining the surroundings and under side surfaces of the waterproofing treatment in bone dry condition for 10 years. During the guarantee period the contractor shall attend all leakages, defects etc. if noticed, free of cost, starting the work of checking up and rectification within a week's time from the date of intimation about such leakages/ defects. b) The measurement for payment shall be actual area covered by the treatment. c) The waterproof brick bat coba filling coming over the waterproof plaster shall be measured in Cum separately and the cost of the same is not included in this item.

Providing and fixing of Cast Iron cover of approximate 600 mm dia and as per MCGM requirement on Over head water tank with locking arrangement MS strips including cementing, painting , removing damaged/rusted covers carefully and deposit to store etc all complete as per drawings,specifications and as directed by the Engineer-in-Charge.

Providing & fixing good quality SS floor grating (Jali) in bath & toilet including fixing the jali with white cement matching the floor level etc. complete as per specification, drawings and as directed by EIC.

Labour charges for attending emergency complaint of exposed PH fitting/sanitary wear like wc & wash basin, leakage including all material like-tee/elbow/coupling/washer of GI/CPVC , solvent, tools etc. complete all as per specifiction and as directed by EIC

Labour charges for attending emergency complaint of concealed PH fitting leakage including breaking of tiles/plastering/concrete and providing all the required material like tee/elbow/coupling of GI/CPVC , solvent, tools etc. complete all as per specifiction and as directed by EIC

Providing & fixing in position approved quality cPVC stop cock/ Bib tap /push tap/jet sprey two-way bib tap etc. of 15 mm nominal dia.for PUBLIC TOILET with IS mark / approved make including providing and fixing C-PVC jointable / threaded fittings such as Union, Nipples, Bendes, Elbows, Tees, Reducers, End caps, Couplers, Adaptors, Saddles, Plugs, Tank connectors, Expansion loops, Bypass bends, etc with leak proof threaded joints using spun yarn, white zinc etc., testing the joints, rectifying the leaky joints, if any, including cleaning etc. complete all as per specifications and as directed by Engineer- in- Charge.

CPVC stop cock of approved make

CPVC bib tap of approved make

CPVC push tap for urinal of approved make

CPVC Jet spray with flexible pipe of required length and approved make.

CPVC Two-way Bib tap

Supplying only of following PH Items

a) 15 mm dia. CP brass non fancy screw down BIB TAP weighting between 400gms to 500gms make with ISI mark.

b) 15 mm dia. CP brass non fancy screw down PILLAR TAP weighting between 625gms to 650gms make with ISI mark.

JAGUAR' - Continental Series - i)Continental knob ZKB-001 with tikki and screw.

JAGUAR' - Continental Series - ii) spindle ( code No : ZCA - 001)

'JAGUAR' - Continental Series - iii) Piston with O ring ( code No : ZCA - 008)

JAGUAR' - Continental Series - iv)Bush with O ring ( code No : ZCA - 007)

'JAGUAR' - Continental Series - v) Center lever handle for wall mixture ( code No : ZKB - 049)

JAGUAR' - Continental Series - vi) Aerator for wall mixture 24 mm ( code No : ZMS - 069)

JAGUAR' - Continental Series - vii) Aerator for sink cock 18mm ( code No : ZMS - 069)

'JAGUAR' - Florentine Series - i)Florentine knob ZKB-007 and screw.

'JAGUAR' - Florentine Series - ii) spindle ( code No : ZCQ - 048)

'JAGUAR' - Florentine Series - iii) 115 mm long bend pipe set for wall mixture ( code No : ZMS - 012)

Teflon tape 12 mm x 10 mt length ( 0.075 mm thick)

M seal - 25 gms.

Aradite Adhsive -100 gms

CPVC pipes /fittings

i) 15mm brass elbow

ii) 15mm coupling

iii) 15mm brass tee

iv) CPVC Solvent Cement Ultra Strong for CPVC and UPVC Pipes and Fittings (200 ml, Tin Can )

v) 32mm dia Metropole flush valve (FLV-CHR-1085N)

vi) 32mm dia Metropole flush valve pistone kit (ZFV-CHR-234A)

vii) 32mm dia Metropole flush valve stoper bush (ZFV-XHR-236)

Supplying 32/40mm dia. Heavy quality PVC flexible pipe to existing sinks/wash basins

Supplying only of following Civil Items

Godraj nigth latch -sliding tounge

Plain glass self with edge polishing and heavy - 450mm x 100 mm x 6mm thick

Plain glass self with edge polishing -600mm x 100 mm x 6mm thick

Heavy duty glass self bracket (for 6mm thick glass) 75 mm long.

Heavy duty door stopper

Heavy quality magic eye / door viewer of brass body, having minimum 180 degree wide angle lens suitable for flush door of thickness 35mm to 50 mm, total length closed condition 40 mm, outside dia 25 mm, mounting diameter 14 mm having full thread for length adjustment

Nylone rope 6mm dia length not less than 30 meter.

Nails -3/4"(2 kg),1"(2 kg),1 1/2"(3kg),2"(2kg),3"(1 kg)

A) GI Counter sunk screw (1 box=100 nos)

1 kg pack of white cement approved make

50 kg pack of OPC ( Cement) approved make

40 kg pack of Readymade plaster 1:4 approved make

B) PPR pipe fittings i) 20 mm brass elbow

PPR pipe fittings ii) 20 mm coupling

PPR pipe fittings iii) 20 mm brass tee

i) 25mm brass elbow

ii) 25mm coupling

iii) 25mm brass tee

i) 32mm brass elbow

ii) 32mm coupling

iii) 32mm brass tee

i) 40mm brass elbow

ii) 40mm coupling

iii) 40mm brass tee

Labour charges only for carefully removing / dismantling the existing PPR Water supply pipe line of all dia. in all sizes, along with its existing fittings at all floors and location including cleaning the pipes with thin rod, removing sand particles or miscellaneous other obstructions in pipes and fittings including labour charges for replacing the damaged / unserviceable G.I. Pipes & fittings wherever found necessary including refixing the same in its original position in proper line, level and plumb with necessary specials / fittings making threadings, jointing the pipes and fittings with hemp yarn, white zinc paste, clamping, testing the pipes & fittings for leak proofness and smooth working including returning the defective / unserviceable materials to stores of maintenance Units etc. complete all as per specifications and as directed by the Engineer-in-Charge. NOTE: Necessary materials required for replacement shall be supplied by the deptt. free of cost.

Providing and Fixing PPR Ball valve with S.S balls & Specials, if required of approved make suitablefor pipe pressure class, making water proof joints,for pipe pressure class, making water proof joints,ncluding cost of jointing material and PPR specials if required, testing the joints etc. complete as per directions of EIC.

20 mm dia.

25 mm dia

32 mm dia.

40 mm dia.

50 mm dia.

63 mm dia.

Providing & fixing on Exposed or concealed surfaces the following dia PPR pipe of specified class of M/s. SUREME / PRINCE or other approved equivalent consisting following items of work:- i) Supplying & fixing PPR pipes, including necessary all fittings conforming to relevant IS code ii) Laying and fixing the pipe and specials on exposed surfaces to correct line, level and plumb for water supply line, overflow and vent using M.S. nails/screws, rawl plugs, wooden gutties and branded clamps of Supreme/Prince make to the pipeline as per the site requirement. iii) Testing the pipe line to a hydraulic pressure as per manufacturers cataglouge for leak proof joint or as per relavant code iv) Making leak proof threaded / solvent joints. including cutting the pipe, Joint preparartion, cleaning, marking, application of solvent, assembling, curing etc. and the cost of jointing cement solvent materials. v) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition. proof joints. vi) Providing and fixing PPR jointable / threaded fittings such as Union, Nipples, Bendes, Elbows, Tees, Reducers, End caps, Couplers, Adaptors, Saddles, Plugs, Tank connectors, Expansion loops, Bypass bends, etc vii) including removing existing GI pipe line/cPVC/uPVC/PVC /PPR with fittings and specials etc. PPR Pipes and Fittings

a) 20 mm n.b

b) 25 mm n.b

c) 32 mm n.b

d) 40 mm n.b

e) 50 mm n.b

f) 63 mm n.b

Description of Work / Item(s)

Amount

Part III - Rebate Items

Rebate for taking away dismanteled item by the contractor……

a) Teak wood

b) Scrap wood

c) Panelled / Flush door shutter up to 38 mm thick

d) CP brass PH items like bib tap, pillar cock, stop cock, ……

i) bib tap

ii) stop cock

iii) pillar tap

iv) bottle trap

v) waste couplings

vi) towel rod

e) GI Pipes

i) 15 mm n.b

ii) 20 mm n.b

iii) 25 mm n.b

iv) 32 mm n.b

v) 40 mm n.b

vi) 50 mm n.b

vii) 65 mm n.b

viii) 80 mm n.b

f) replacement of CI & PVC pipes

i) 75 mm dia.

ii) 100 mm dia.

g) GM gate valves up to 50 mm dia.

i) 15 mm n.b

ii) 20 mm n.b

iii) 25 mm n.b

iv) 32 mm n.b

v) 40 mm n.b

vi) 50 mm n.b

vii) 65 mm n.b

viii) 80 mm n.b

h) PVC flushing cistern

AMBIKA ENTERPRISE (BID ID -3253283)

AMBIKA ENTERPRISE (BID ID -3253283)

AMBIKA ENTERPRISE (BID ID -3253283)

AMBIKA ENTERPRISE (BID ID -3253283)