TENDER FOR CONSTRUCTION OF SEAFARERS CLUB

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre).

Quarry Dust or M-Sand Filling : Supplying and filling in isolated foundations and the area wherever required below ground level and sides of the foundation and walls with Quary dust in layers not exceeding 150 mm thick, including well watered and compacting, levelling, etc. complete, and as directed.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for

Columns, Pillars, Piers, Abutments, Posts and Struts

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Stairs, (excluding landings) except spiral-staircases

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grade of concrete. Concrete of M30 grade with minimum cement content of 350 kg /cum (All works upto plinth level) Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grade of concrete. Concrete of M30 grade with minimum cement content of 350 kg /cum (All works above plinth level upto floor V level) Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding: Thermo-Mechanically Treated bars of grade Fe-500D or more

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing & applying 12 mm thick cement plaster in CM 1:4 (1 part of cement: 4 parts of sand) to walls internally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces, scaffolding, rounding off or champhering of corners, offsets, fin/ bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiselling the undulated surface wherever necessary and curing, etc., all materials and labour complete in all respects including all lead, lift and descent and complete complying with specifications and as instructed by the Engineer in charge.

Cement Plaster in fine sand - 20mm cement plaster of mix 1:4

Providing cement plaster for the ceiling of roof slabs, beams and columns with 10mm thick cement mortar 1:3 including hacking and preparing the surface, scaffolding, finishing, curing all complete as per drawings and specifications and as directed by the Engineer.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water -proofing compound confirming to IS 2645 including cleaning the surface before treatment, (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabsand as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete (c) After two days of proper curing applying a secound coat of cement slurry admixed with proprietary water proofing compound conforming to IS : 2645. Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test, All above operations to be done in order and as directed and and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete With average thickness of 120 mm and minimum thickness at khurras point.

Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge : 15 mm wide and 15 mm deep groove

Providing plaster drip course/ groove in plastered surface or moulding to R.C.C. projections

Providing Plain Cement Mortar Bands of 18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement : 4 fine sand): - Moulded Band

DOORS, WINDOWS & GRILLS Providing and fixing in position First class country wood (padauk) wrought main frames for door frames with necessary M.S. hold fasts / clamps fixed suitably to the masonry / concrete including cutting pockets and grouting with P.C.C. 1:3:6 (1 cement : 3 coarse river sand : 6 hard granite graded stone aggregate of 20mm nominal size) in volumetric proportions, curing including painting with one coat of boiling coal tar paint on the portions of the timber abutting against masonry / concrete all as shown in the drawing and as directed including cement and all other materials, labour, tools, equipment, etc., complete.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete 35 mm thick including stainless steel butt hinges wirh necessary screws (single leaf)

Providing and fixing Second class teak wood glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. (Second class teak wood of 35mm thk shutter)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. (Fixed to steel windows by welding)

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made: Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made: Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm , sash 67 x 80 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 3.00 sqm upto 5.00 sqm). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.

Providing and fixing Float glass panes of nominal thickness 5 mm (weight not less than 12.50 kg/sqm)

Supplying and Appplying Weather/structural non sag elastomeric PU sealant (600ml Sausage) for joints in RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum/ Alluminium work complying to ASTM C920, DIN 18540-F & ISO 11600

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass door latch with necessary screws etc. complete : 300x16x5 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

TILES Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Glazed vitrified floor tiles polished finish of size Size of Tile 800 x 800 mm

Glazed vitrified floor tiles polished finish of size Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 800x800 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. (40 mm thick with 20 mm nominal size stone aggregate)

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. - For Substsation building. (40 mm wide and 4 mm thick)

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

PAINTING Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete wherever required and as directed by the Engineer-in-charge including all labour, material, tools, scaffolding, etc. Complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre and as directed by the Engineer-in-charge including all labour, material, tools, scaffolding, etc. Complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre

Applying priming coat With ready mixed red oxide zinc chromate primer including Second Coat of approved brand and manufacture on steel galvanised iron/ steel works wherever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Applying Wall painting with premium acrylic emulsion paint of interior grade (Two Coats), having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour where ever required and as directed by the Engineer-in-charge including all labour, material, tools, scaffolding, etc. Complete.

Applying wall painting with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing & applying with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete on steel works.

Providing and applying white washing with lime even shade three coats in wall surface and where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

"Providing and applying ready mixed (oil bound washable distemper / Acrylic distemper) of approved manufacturer of required shade of 2 (two) coats over one coat of primer wherever required and as directed by the Engineer-in-charge including all labour, material, tools, scaffolding, etc. Complete.

Painting exterior surface with TEXTURED exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with: On new work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. - PARITION & DOORS.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides , ball bearing and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. (80x1.25mm MS lath with 1.25mm thick top cover) where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required and as directed by the Engineer-in-charge including all labour, material, tools, scaffolding, etc. Complete.

Supply, fabrication, transporting, assembling & erecting in place, the Pre-designed, Pre-Engineered Prefabricated Structure including all columns, rafters, purlins, portals, trusses, beams, plates, sag rods, canopy etc., with all primary & secondary structural members, etc complete for PEB shed having dimension of 9.46m x 10.46m and canopies as per drawing. All fasteners to be used for fitting the roof and holding surface should be of non rusting coated. This item also includes Design, Preparation and submission of design details, detailed fabrication drawings for Pre Engineered Building. The design and drawings to be provided as per the IS norms in applicable zone and shall be submitted to KPL/ consultant for their approval. The job also includes providing monkey ladder in approved design, section thickness for safe access to roof. steel grade E350A, conforming to IS-2062.

PLAY COURTS Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying and filling clay mixed with soil for Shuttle/Tennis court all as per drawing and specification as per drawing and as directed by Engineer-in -charge at site including all labour , material, transportation, equipment , fuel etc., complete

Providing and laying in position bitumen hot sealing compound for expansion joints using grade ‘A’ sealing compound in Shuttle/Tennis court all as per drawing and specification and as directed by Engineer-in -charge at site including all labour , material, transportation, equipment , fuel etc., complete

Providing grit filling in Basket ball /Badminton court all as per drawing and specification and as directed by Engineer-in -charge at site including all labour , material, transportation, equipment , fuel etc., complete

Supplying and fixing M.S Pole as per drawing and specification at Basket/Badminton Court including painting with Synthetic enamel paint with prime coat as directed by Engineer-in -charge at site including all labour , material, transportation, equipment , fuel etc., complete

Site grading by cutting the soil heaps and filling the earth in low level areas mechanically by using excavator and loader /tipper within a lead of 1km all complete and as directed by Engineer-In-Charge including all labour, tools etc., all complete

Disposing the surplus soil mechanically by using excavator and loader /tipper within a lead of 5km and as directed by Engineer-In-Charge including all labour, materials , transport, Equipment , tools , fuel etc., all complete Note: 1.The tenderer shall maintain trip sheets in triplicate in KPL approved format at his own cost for the quantity of surplus transported. 2. Payment will be made based on the lorry cubical content. 20% deduction of voids will be made for Suplus earth. 3.However the final quantity will be restricted to (i) actual quantity of Earthwork minus refilling quantity for surplus earth

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1Cement : 3 crushed stone aggregate), including the cost of required centering, shuttering complete with CC 1:1½:3 (1 Cement: 1½ crushed stone aggregate : 3 graded stone aggregate 20 mm nominal size) whereever required as per drawing and specification all complete.

Providing and Fixing of 2" Dia, SS-304 Handrail with fabricated items for Staircase, Ramp and whereever required as directed at site like Connectors, floor plate, mid rail including all anchors, fasteners, hardware, and accessories necessary to complete work and as directed by the KPL Engineer.

PARTITIONS

Providing and fixing 75mm thk Full Height Veneer finished PLY wood Partitions using 25 x 50mm anodised aluminum section framework @ 600 c/c bothways with horizontal noggings at floor and soffit, both side skinning with 12mm thick veneer finished PLYwood. All electrical/network switch boxes, niches to be boxed/packed with adequate reinforcement using PLYwood. The aluminium channel to be provided at intersection of two materials. The partition may have 6mm thk glass panels at specified areas as per the drawing fixed with veneer finished PLY Jamb lining all around. Note cost to include aluminum frame upto actual ceiling (frame to be anchored to actual ceiling). Complete as per drawing and directions. The veneer should be of teak or equivalent ( Basic cost of veneer - Rs.80) (Measurement will be taken as only for veneer finished area). Both side Veneer finished partition - FULL HEIGHT

FALSE CEILING

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge with 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6 sqm )

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mmthick (galvanized @ 120 grams per sqm including both sides)comprising of main-T runners of size 24x38 mm of length 3000 mm,cross - T of size 24x32 mm of length 1200 mm and secondaryintermediate cross-T of size 24x32 mm of length 600mm to formgrid module of size 600 x 600 mm, suspended from ceiling usinggalvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to pierce into 12x50mm or even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to be fixed on periphey wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall S.S screws. The workshall be carried out as per specifications, drawing and as per directionsof the Engineer-in- Charge with 15 mm thick tegular/butt edged without perforation plain/designer light weight calcium silicate Anti-Microbial Bio-Safe coated false ceiling tiles Confirming to JIS-Z2801 and ASTM G-21 sqm - TOILETS

Description of Work / Item(s)

Amount

WIRING IN PVC CONDUIT Point wiring in PVC conduit, with modular type switch. Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated multistrand copper conductor wires in surface / PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated multistrand copper conductor wires etc. as required and as per technical specification and as per latest IS / IEC

Point wiring in PVC conduit, Wiring for group controlled (looped) Wiring for light point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated multistrand copper conductor wires in surface / PVC conduit, earthing the point with 1.5 sq.mm FRLS PVC insulated multistrand copper conductor wires etc. 1 Switch may be connected to 3 points, out of which 1 point will be accounted in item no.1 and other 2 points will be accounted in item no.2 as required and as per technical specification and as per latest IS / IEC

Twin control point wiring in PVC conduit, with modular type switch Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated multistrand copper conductor wires in surface / PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated multistrand copper conductor wires etc. as required and as per technical specification and as per latest IS / IEC.

Circuit/ submain wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated multistrand copper conductor wires in surface/ recessed PVC onduit as required and as per technical specification and as per latest IS / IEC

2 x 1.5 sq. mm + 1 x 1.5 sq mm earth wire

2 x 2.5 sq. mm + 1 x 2.5 sq mm earth wire

2 x 4 sq. mm + 1 x 4 sq mm earth wire

2 x 6 sq. mm + 1 x 6 sq mm earth wire

4 x 6 sq. mm + 2 x 6 sq. mm earth wire

4 x 10 sq. mm + 2 x 6 sq. mm earth wire

Supply and drawing of 4 Pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed PVC conduit as required and as per technical specification and as per latest IS / IEC

Supply and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required and as per technical specification and as per latest IS / IEC

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required and as per technical specification and as per latest IS / IEC

Supply and Fixing Power plug Point Modular type accessories: Supply and fixing of metal box of GI box with modular plate and cover in front on surface or in recess , including providing and fixing of 3 pin 5/6 amps. modular socket outlet and 5/6 amps. modular switch, connections, painting etc. as required. (For light plugs) and as per technical specification and as per latest IS / IEC

Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos of 3 pin 5/6 socket outlet and 2 nos 5/6 A modular switch, connections etc. and as required and as per technical specification and as per latest IS / IEC

Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. and as required and as per technical specification and as per latest IS / IEC

Supply & fixing of suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 20 A modular socket outlet and 20 A modular SP MCB, "C" curve including connections, painting etc. as required and as per technical specification and as per latest IS / IEC

Supply and fixing of following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required and as required and as per technical specification and as per latest IS / IEC

15/16 Amp. Switch

3 Pin 5/6 Amp. Socket

6 pin 15/16 A socket outlet

Telephone socket outlet

T.V socket outlet

Bell push

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

3 Module

4 Module

6 Module

8 Module

12 Module

Supply and fixing modular type electronic fan regulator: Supplying and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required and as per technical specification and as per latest IS / IEC MCCB, MCB & DB’S

Supply and fixing of following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) and as per technical specification and as per latest IS / IEC - 16 way , Double door

Supply and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) and as per technical specification and as per latest IS / IEC

4 way (4+12), Double door, Horizontal type

6 way (4+18), Double door, Horizontal type

8 way (4+24), Double door, Horizontal type

12 way (4 + 36), Double door Horizontal type

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) and as per technical specification and as per latest IS / IEC

4 way (4 + 12), Double door

8 way (4 + 24), Double door

Supply and fixing 'C' Series, SP MCB : Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required and as per technical specification and as per latest IS / IEC

Single pole

Double pole

Triple pole

Triple pole and neutral

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32 A 415 V "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing double pole flame proof encloure recess along with 16/20 A 240 V "C" curve TP MCB complete with connections, testing and commissioning etc., as required.

Supplying and fixing 40 A to 63 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required and as per technical specification and as per latest IS / IEC 40Amp./63Amp. FP MCB

EARTHING Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but with charcoal/ coke and salt ) as required as per technical specification and as per latest IS / IEC

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) and as per technical specification and as per latest IS / IEC

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required and as per technical specification and as per latest IS / IEC

LIGHT FITTING AND FAN Supply,Fixing ,testing & commissioning of all type of light Fixtures complete with fixing accessories and mounting bracket,earthing for the fittings all complete as required.(connection from the ceiling rose or junction box to light fixture with terminations).Note : All light fixture with Electronic Ballast with THD <10% as per technical specification and as per latest IS / IEC

Suppling Installation Testing & Commissioning of 3 feet height LED Bollard light - 15 Watts cool white Flicker free, high efficiency and robust industrial batten family suitable for Surface, Ground and Conduit mounting and as per technical specification and as per latest IS / IEC

Suppling Installation Testing & Commissioning of upto 200 WATT Flood light surface mounted downlight with options of LED efficacy more than140 lumens / watt - Poly carbonate IP65 LENS -60 degree angle as per technical specification and as per latest IS / IEC.

Suppling Installation Testing & Commissioning of upto 150WATT Flood light surface mounted downlight with options of LED efficacy more than140 lumens / watt - Poly carbonate IP65 LENS -60 degree angle as per technical specification and as per latest IS / IEC.

Suppling Installation Testing & Commissioning of 30Watts LED Fully diffused recessed Mounted 2'X2' LED luminaire with high transmitive diffuser suitable for indoor spaces as per technical specification and as per latest IS / IEC.

Suppling Installation Testing & Commissioning of upto 15 WATT LED Slim profle surface mounted downlight with options of 700 to 2000 lumen as per technical specification and as per latest IS / IEC.

Suppling Installation Testing & Commissioning of upto 10W LED Extruded Aluminium batten available in 2ft run length suitable for mirror with multiple lumen packages and suitable for Surface, Wall & Conduit mounting (with accessories). as per technical specification and as per latest IS / IEC.

Suppling Installation Testing & Commissioning of upto 8 WATT LED Slim profle surface mounted downlight with options of 700 to 2000 lumen as per technical specification and as per latest IS / IEC

Suppling Installation Testing & Commissioning of upto 20 WATT LED Slim profle surface mounted downlight with options of 700 to 2000 lumen as per technical specification and as per latest IS / IEC

Suppling Installation Testing & Commissioning of 10 Watts Pressure Die cast housing LED bulkhead with IP66 Protection and IK09 impact resistance suitable for surface and wall mounting applications as per technical specification and as per latest IS / IEC.

Supplying installation testing and commissioning of upto 10W LED based retro fit bulb and as per technical specification and as per latest IS / IEC.

Supply of 1200 mm sweep size special design energy saving ceiling fans with low power consumtion aluminum motor covers of larger diameters complete with double ball bearings, Aluminium blades, down rod, shackle insulator, canopy but without regulator etc complete as required or equivalent and as per technical specification and as per latest IS / IEC.

Supplying installation testing and commissioning of modular type Night lamp In GI box to be concealed on wall

Supply Installation Testing Commissioning of Exhaust type Fan With all Accessories etc as required.(HEAVY DUTY)

Supply,Installation, Testing and Commisioining of LED rope light with adopter, End holder and all accessories as required as per site conditions. 5 MTR BOX

Supplying installation testing and commissioning of 450mm Dia Wall mounted fan and as per technical specification and as per latest IS / IEC.

Farbrication, supplying, installation, testing & commissioning of weather proof box made out of hot moulded SMC sheet of size 285mm x 210mm x 117mm complete with 4 Nos. electrolytic aluminium busbar of 63 Amps. with porcelain base and suitable din bar including supplying and fixing one No. 16 A SPMCB complete with connections & inter-connections etc. as required (SINTAX Make).

MAIN PANEL BOARD Supplying, erecting,testing and commissioning of main Panel suitable for 415 volt, 3 phase and 4 wire system, fabricated from 18 SWG thick CRCA sheet with Dust and vermin proof, cubicle type,floor mounted,front operated, fully compartmentalised with seven tank treament and powder coated siemens grey .All the switch gear door are hihged type with rubber gasket,name plate, removable type cable gland plate and base frame and following components and all related accessories etc. INCOMING : -Supplying, erecting, connecting & commissioning 250 AMPS 4P ( Source Changeover Systems )Automatic transfer switch ( motorised type 2 input & 1 out put.) metal sheet enclosure with necessary inter connections,cable box, brackets, screws, bolts, nuts, etc. Make : schneider/hpl-socmec. OUT GOINGS 125 Amps TPN MCCB with Adjustable overload and short circuit with 36 KA (Ics) with standing capacity 1Nos. 100 Amps TPN MCCB with Adjustable overload and short circuit with 36 KA (Ics) with standing capacity - 1Nos. 63Amps TPN MCCB with Adjustable overload and short circuit with 36 KA (Ics) with standing capacity - 15Nos. BUSBAR : 250 Amps TPN CU, Phase -40 x 8 mm, Neutral -40 x 6mm and Earth - 2R X 25 x 06mm METERING COMPARTMENT : 1no Digital multifuntional meter with RS 432 Connetecots Accuracy class 1.0 with 3nos of CTs 250/ 5 amps ratio and RYB clustered type indication lamps with control fuses.- 2 set as per technical specification and as per latest IS / IEC

5 KVA online UPS Supply, installation, testing and commissioning of Independent 5 KVA UPS system with 440V Three phase input and 230V single phase output with all required accessories & battery bank for 60 mins back up with covered SMF battery and battery rack for all new required loads covered in this project as per the detailed technical specification enclosed

LT ,1100V GRADE PVC / XLPE Armoured UnderGrounds Cables. Supplying of LT under ground/Power XLPE cable having Aluminium conductor, extruded Flame retardant PVC outer sheathing steel wire/tape armoured & the inner sheath with polypropylene, suitable for 1100V class confirming to IS. The rate shall include a.Cable clamps on walls,columns,beams,built-up trenches,cable markers etc. for indoor cables. b.Covering bricks or tiles,cable markers etc for Outdoor cables. c.Earthing the glands armouring etc.,complete as required as per site conditions.

4 core 16 sqmm

3.5 core 25 sqmm

3.5 core 50 sqmm

3.5 core 120 sqmm

Supplying of LT under ground/Power XLPE cable having Aluminium conductor, extruded Flame retardant PVC outer sheathing steel wire/tape armoured & the inner sheath with polypropylene, suitable for 1100V class confirming to IS. The rate shall include a.Cable clamps on walls,columns,beams,built-up trenches,cable markers etc. for indoor cables. b.Covering bricks or tiles,cable markers etc for Outdoor cables. c.Earthing the glands armouring etc.,complete as required as per site conditions.

3 core 4 sqmm

3 core 6 sqmm

4 core 6 sqmm

4 core 10 sqmm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering bricks and refilling the trench etc as per technical specification and as per latest IS / IEC

Upto 35 sq. Mm

Above 35 sq. mm and upto 95 sq. Mm

Above 95 sq. mm and upto 185 sq. Mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium/copper conductor cable of 1.1 KV grade as required as per technical specification and as per latest IS / IEC

4 X 16 sq. mm (28mm)

3½ X 25 sq. mm (28mm)

3½ X 50 sq. mm (35mm)

3½ X 120 sq. mm (45mm)

4 core 10 sqmm

Description of Work / Item(s)

Amount

PART A: SANITARY FIXTURES AND CP FITTINGS

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm (Single bowl) bowl depth 250 mm.Make:Crystal,Carysil

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm (Double bowl) bowl depth 250 mm.Make:Crystal,Carysil

Providing & fixing of Vitreous China Flair bowl Wash Basin of approved size & make installed Over granite counter type, with a pair of brackets, fixing to wall daddo with required materials like plastic plugs, packing pieces, screw nails etc, with C.P Mixer cock of approved type & model, 32mm dia C.P.Waste coupling, 32mm dia C.P. bottle trap, C.P.connecting pipe, 15mm dia C.P.angle stop cock for cold water supply with wall flange etc. The work Shall include cutting & making good the walls & floors, testing & commissioning the installation .TOTO WB LW951CJ CONSOLE LAVATORY 1 TAP HOLE W/BRACKET,HSN : 69101000

Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required: Range of four squatting plates with 10 litre P.V.C. automatic flushing cistern

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape,size and pattern including integrated white vitreous china cistern ofcapacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Supply, Installation, Testing & Commissioning of white vitreous European wall mounting of approved make including Cisten (Capcity 3/6 lit) with Flush Plates of approved make including required "P" trap, seat cover, cistern fittings, nuts, bolts, Rubber gasket, wall cutting as required etc., complete. making holes in masonry or concrete,restoring the damaged materials, testing & commissioning the nstallation etc complete., Make : Toto Geberit CT 110.120.00.1 KF-B WC Alpha-10cm 90/110 6L IN,HSN: 39229000, Geberit ACP 115.045.21.2,Alpha Dual Pl Bright Chr,HSN: 39229000,TOTO Ceramics WC CW822RA#W"Avante" Wall HungRimless Fixing kit HSN:69072100 , TOTO SC TC385VS,Seat & Cover - Soft Close,HSN:39222000, TOTO AP TX215C ,Slip-in Connector,HSN: 40169390

Providing and fixing of CP health faucet , Hand operated spray unit (instant type) with CP Crutch and PVC flexible tube of 1.0m length. ,TOTOHX20MCRB

Providing and fixing of 15mm dia CP brass Robe Hook with wall flange. MAKE : TOTO

Providing and fixing of 15mm dia CP brass Toilet Roll Holder with wall flange.

Providing, fixing, testing and commissioning of CP brass superior quality Towel ring with flange with concealed brass screws etc. including cutting & making good the wall etc. Make :Toto-YT903S4

Providing and fixing of shower assembly unit consisting of over headShower, arrangements with shower arm including cutting, chasing & making good the walls. TOTO SHW TX488SI,ICON'Fixed Shower Head W/Pipe -Wall Type HSN: 84818020

Providing and fixing of shower assembly unit consisting of HandShower, arrangements with shower arm including cutting, chasing & making good the walls. TOTO FT TBW02006A,Hand Shower 3 mode,with hanger and hose HSN: 39221000

Providing and fixing Concealed Body For S/L Diverter 40Mm Car, Single Lever Exposed Parts Kit Of Diverter and Hand Shower 100Mm Dia Round Shape Single Sliding rail 19mm and 600mm long round, Shower Arm casted 190mm long light body,O/Head shower singleflow 100mm dia,Flexible Tube 8mm dia and 1.5mt long including all material work completed. TOTO DVT TBG04304B,Single Lever Shower,Mixer with diverter HSN: 84818020,TOTO TBN01001B,Concealed Box,HSN: 84818020

Providing and fixing consisting of Bath Spout, arrangements including cutting, chasing & making good the walls. TOTO SP TTBR101,Bath Spout W/DiverterHSN: 84818020

Providing and fixing of 15mm dia CP brass angle stop cock with wall flange. Make :Toto

Providing and fixing of 15mm dia CP brass stop cock with wall flange. Basic cost of Stop Cock: Rs. 500 [Jaquar (Model No.- ARI - 39083K)]

Supplying and fixing soap holder with metalic bottle and necessary SS screws, etc complete Make :Toto

Supplying and fixing, soap dispenser with metalic bottle and necessary SS screws, etc complete Make :Toto

PART B : CPVC PIPES AND FITTNGS (INTERNAL AND EXTERNAL WATERSUPPLY)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. INTERNAL (CONCEALED IN WALL) : COLD & HOT WATERSUPPLY Note: Strictly use SDR-11 /13.5 grade ASTRAL - CPVC pipe and fittings for internal hot water supply up to 50 mm dia.

20 mm dia (SDR-13.5) For Cold water

20 mm dia (SDR-11) For Hot water

25 mm dia (SDR-13.5) For Cold water

32 mm dia (SDR-13.5) For Cold water

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. -VERTICAL SHAFT/ TERRACE Note: Strictly use SDR-11 /13.5 grade ASTRAL - CPVC pipe and fittings for internal hot water supply up to 50 mm dia.

25mm dia

32 mm dia

40 mm dia

50 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. Below Ground Level Header :

20 mm dia

25 mm dia

32 mm dia

40mm dia

50mm dia

110 mm dia

Providing, fixing testing and commissioning of Gun metal brass Ball Valve including unions etc., Complete

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

Providing, fixing, testing and commissioning of cast iron lever operated slim seal type butterfly valves of CI body and spheroidal graphite iron disc (SG iron),with nitrile rubber seal, tested to 10 kg / sq.cm Confrming to BS 5155 / MF6 standards and including a set of GI flanges as per BS-10 table 1 including bolt nuts, and Neoprene rubber gaskets etc., Complete (Inter valve make).

50 mm dia

65 mm dia

Providing, fixing, testing and commissioning of brass body nickel plated automatic air release valves with brass splindle, NBR and joinfraniteelastomer,staniless steel spring polypropylenic float at the top most points of watersupply distribution ringmain. 25 mm dia

Providing, fixing, testing and commissioning of brass`Y' / pot stainer screw type tested to 20 kg / sq.cm.

32 mm dia

20 mm dia

Providing, fixing, testing and commissioning of slimseal flap type NRV ( valve ) with CI body and cast steel disc pressure rating PN-10 Kg / sq.cm

32 mm dia

25 mm dia

20 mm dia

Providing, fixing, testing and commissioning of SS or BRASS pressurized ball float valve with gun metal lever of approved quality for OHT filling inlet. 25 mm dia

Providing, fixing, testing and commissioning of Outer ( Gate valve ) Main line for Metro water with CI body 80 mm dia

Construction of valve chambers of internal clear dimension as mentioned below by using first class table moulded modular bricks 230 mm thick wall in cement mortar joints in 1:4, over CC 1:4:8 bed 150 mm thick & plastering in CM 1:6 15 mm thick with adding water proof compound as per standard specifications for bottom and internal side walls, exposed top surface funished smooth etc., including necessary execavation in all types of soil excluding soft rock and hard rock, back filling with available excavated earth including consolidation in layer not exceding 200 mm in depth, disposing of surplus earth to all leads & providing precast ready made lighty duty RCC cover with frame of SFRC with frame (as per standard make or SFRC / southern concrete company) curing etc. complete. Size 600 x 600 x 750mm deep

Providing, fixing, testing and commissioning of ball valves (GARDENING Tap) of brass body nickel plated with stainless steel ball, lever operated with gun metal nozzel for connecting rubber hose (RB / ZOLOTO make) and tested to 20 kg / sq.cm. 20 mm dia

Supply and fixing 600mm long puddle flange consisting of 6mm thick welded GI / MS plate, flanges of sutible size hot dip galvanised to 100 micron properly fixed in walls of water tanks as per specifications and approved drawings and shall be of following diameters. FOR U.G.SUMP

25 mm dia

40 mm dia

50 mm dia

65 mm dia

110mm dia

PART – C: PVC SOIL,WASTE,VENT PIPES AND FITTINGS ( INTERNAL & EXTERNAL)

Providing, fixing, testing and commissioning of PVC soil, waste and vent pipe confirming to IS 13592 of SWR quality 6 kg / sq.cm pressure rated including all fittings, like Bends, Tees, Elbows, Collars, junction, offsets, access pipes, jointing with solvent cement followed by application of leak proof adhesive like FRP paste & laid on floors inside the toilets kitchen and utility to the required slope including making necessary bores in walls as applicable, making good the bores with CM 1:3 or cement concrete as applicable, curing etc., complete. Note : Wall chasing shall be done with chasing machine to required lines and levels.

INTERNAL (TOILET): 75mm dia waste pipe ( Type B )

INTERNAL (TOILET): 110mm dia soil pipe ( Type B )

Providing, fixing, testing and commissioning of PVC soil, waste and vent pipe confirming to IS 13592 of SWR Type B quality (6 kg / sq.cm pressure rated) , including all fittings, like Bends, Tees, Elbows, Collars, junction, inspection doors, cowls, offsets, access pipes, jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste, fixed to wall with properly fabricated MS bracket of suitable size, GI 'U' clamps with bolts, nuts and GI washers complete, for soil and waste pipe lines laid in vertical shafts.

EXTERNAL (IN SHAFTS Toilets waste): 75mm dia waste pipe ( Type B )

EXTERNAL (IN SHAFTS Toilets waste): 110mm dia soil pipe ( Type B )

Providing, fixing, testing and commissioning of PVC sewer line of prince / supreme make confirming to IS 4985 of Agricultural series - 6 kgs / sq.cm pressure rated, for Under Ground Drainage laid under the soil from chamber to chamber outside the building, to the required slopes, jointing with solvent cement followed by application leak proof adhesivesof FRP paste, including haunching / covering only the joints with cement concrete 1:3:6 at all the joints with and testing of joints with water column etc. complete. Note : Rate is excluding for earthwork and backfilling. It shall be measured separate and paid for. 110mm dia (6kg/sq.cm pr. Rated)

Providing, fixing, testing and commissioning of PVC trap of self cleansing design moulded or fabricated, if not available in size mentioned below, with or without vent arm jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste including PVC extension pipe for PVC / floor trap for with surface preparation with finishing etc., complete size: 100 mm dia x 400 mm length. Making good the floors. Note :Rate is excluding for earthwork and backfilling. It shall be measured separate and paid for.

110mm X 75 mm dia Inlet & Out let ( Multi Utility trap )

110mm dia inlet 110mm dia out let (P Trap) - Deep seal type

Providing, fixing, testing and commissioning of PVC connecting collar (fabricated) for connecting PT & WB bottle trap pipe, complete jointing with solvent cement followed by application of leak proof adhesive like FRP paste including cutting and making good the walls and floors.

110 mm x 40 mm dia

110 mm x 50 mm dia

Providing, fixing, testing and commissioning of CP grating cockroach type setting in floor with white cement mortar and making good the floor. 125 mm dia

Providing, fixing, testing and commissioning of PVC waste pipe of agricultural sereis conforming to IS 4985 including all fittings like tees, elbows, bends, collars, coupling, etc jointing with solvent cement followed by application of leak proof adhesive like FRP paste laid on floors inside the toilets to the required slope including making necessary bores in walls / foundations / concrete slab as applicable, making good the bores with CM 1:3 or cement concrete as applicable, curing etc., complete. Note :Wall chasing shall be done with chasing machine to required lines and levels.

40 mm dia (15kg / sq.cm)

50 mm dia (15kg / sq.cm)

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P/s type

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inletsk. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber For 455x610 mm sizeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

For 500x700 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

For 500x700 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

Excavating trenches of required width and depth for external underground drainage pipes, in all kinds of soil exluding soft rock and hard rock including excavation for sockets and dressing of sides, ramming of bottoms & getting out the excavated soil & then refilling the the tranch with soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc., including disposal of excess soil to all leads or as instructed by the site project Engineer.

Regural soil

Excavating Soft rock

Excavating Hard rock

PART – D: PVC RAIN WATER PIPES AND FITTINGS

Providing, fixing, testing and commissioning of PVC rain water pipe confirming to IS 13592 of SWR quality 6 kg / sq.cm pressure rated 10mm, including all fittings, like Bends, Tees, Elbows, Collars, junction, inspection doors, offsets, access pipes, jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste, fixed to wall with properly fabricated MS bracket of suitable size, GI 'U' clamps with bolts, nuts and GI washers complete, for rain water pipe lines laid in vertical shafts.

75 mm dia - 4 kg/sq.cm pressure rated

110mm dia - 4 kg/sq.cm pressure rated

Providing & fixing of PVC baby nahani trap of self cleansing design moulded or fabricated, if not available in size mentioned below, with or without vent arm, connecting to balcony rain water pipe, complete including cutting and making good the walls and floors. 110mm x 75mm dia

Providing and fixing CP grating of 6mm thick with rim including setting in floor with white cement mortar and making good the floor (Chilli Make). 75 mm dia

Providing and fixing of 600 x 600mm HEAVY duty cast iron manhole cover with frame weighing not less than 50 kg for over head and UG sump and stormwater collection tank.

Supply and fixing 600mm long puddle flange consisting of 6mm thick welded GI / MS plate, flanges of sutible size hot dip galvanised to 100 micron properly fixed in walls of water tanks as per specifications and approved drawings and shall be of following diameters.

20 mm dia

25 mm dia

32 mm dia

110 mm dia

PART – E : MISCELLANEOUS

LEVEL CONTROLLERS Supplying and fixing of digital percentage level indicator for the following storage tanks consisting of display unit and level sensor. The display unit should have 2-1/2 digit seven segment LED to display the levels as 0%, 10% --- 100%. The unit should be weather proof and wall / panel mounted input to the unit should be 230V AC. The level sensor should consists of float operated magnetic float switch with one PUF float suitable mounting flange and flame proof enclosure. The unit shall be BMS Compatable a) Domestic raw & treated water storage tank at master UG sump. Location of level indicator near domestic pumps control panel at master pump room.

Supplying , installing, testing and commissioning of approved make vertical magnetic float switch with 52mm dia SS 316 floats, 2-1/2" table F flange and weather proof enclosure to sense high, low level of the sump. Automatic pump controller. Depth of Sump: Approx- 2.5m. Make: Filpro/Approved equivalent

a) Storm water transfer pumps at basement.

b) Pump room dewatering sump

Supplying , installing, testing and commissioning of approved make vertical/horizontal type Electric 'water heater suitable for pressure rating up to 4Kg/sqcm with heating element with thermostat, 2 nos. 15mm dia CP angle valve, pressure relief valve, non-return valve with CP copper connecting pipes with wall flanges etc., complete with all inlets, outlets, valves and all other accessories etc., complete. a) 10 lts. 2 K.W heating element

1.5 Hp- Pressure Booster Pump set Single phase 1.5 Hp Pr. Booster Pump set - Del pipe size: 32 x 25 mm ( 1-1/4" x 1") Head: 18 - 50 Mts ( 165 Ft) , SH - Series, Max Cap: 5 m3 /Hr @35 Mts, 3.5 m3 /Hr @40 Mts. Approved Make . 24 Lts Tank . During service, Site work, Transport, Rubber spares & Painting cost extra. Singlle Phase DOL Starter with Over Load Relay. -

Supplying, testing and commissioning of centrifugal submersible sump pumps, suitable for 415 ± 10% Volts, 3 phase/230 ±10% volts 50 Hz A.C. power supply. Each pump shall suitable for automatic/manual operation complete with control panel, high low level controller for each pump, necessary wiring and all arrangement required to make the system operatoinal as per specification. (Make:- Grundfos or Equivalent) Pump Room Sump Drainage (1W), Capacity/Flow Rate - 2LPS, Set in Pressure - 12 mtr head. Solid Handling - 38mm

Supply and Fixing of Sintex Tank with Capacity - 20000 ltrs. Should be 100% UV stabilized, Made up of 100% virgin material, Threaded lid, Extra insert lid for protection from algae formation, ISI Marked. FDA Approved.

Supplying, laying and jointing glazed stoneware pipes class SP 1 with Stiff mixture of cement mortar in the proportion of 1:1 (1 Cement : 1 Sand) including testing of joints etc., complete, 100mm dia SW pipes

Providing sand cast iron drop connection externally for 60 cm drom from branch sewer line to main sewer manholes including inspection and cleaning eye with chain and lid, sand cast iron drop pipe and bend encased all-round with cement concrete 1:5:10 (1 Cement : 5 Fine aggregate : 10 graded stone aggregte 40mm nominal size) with all centreing and shuttering required in cutting holes in walls and making good with brick work in Cement Mortar 1:4 (1 Cement : 4 Fine aggregate) plastered with cement mortar 1:3 ( 1 Cement : 3 Fine aggregate) on inside on the manhole wall, lead caulked joints between sand cast iron pipes and fittings, stiff cement mortar 1:1 (1 Cement : 1 Fine aggregate) joints between sand cas iron tee and S.W. pipe, making required channels complete as per standard desing and specifications: 100 mm dia SW pipes

Providing sand cast iron drop connection externally for 60 cm drom from branch sewer line to main sewer manholes including inspection and cleaning eye with chain and lid, sand cast iron drop pipe and bend encased all-round with cement concrete 1:5:10 (1 Cement : 5 Fine aggregate : 10 graded stone aggregte 40mm nominal size) with all centreing and shuttering required in cutting holes in walls and making good with brick work in Cement Mortar 1:4 (1 Cement : 4 Fine aggregate) plastered with cement mortar 1:3 ( 1 Cement : 3 Fine aggregate) on inside on the manhole wall, lead caulked joints between sand cast iron pipes and fittings, stiff cement mortar 1:1 (1 Cement : 1 Fine aggregate) joints between sand cas iron tee and S.W. pipe, making required channels complete as per standard desing and specifications: 100 mm dia Sand cast iron drop connection

Supplying, Installing and testing of pipes and conveying to position and jointing to true lines and gradients, PVC pipe of IS 985 (6 Kg/cm2), jointing the pipeline as per specificaiton, testing the pipeline after installation to the specified hydrostatic test pressure including supplying, installing specials like bends, couplers, sockets, connection etc., as per provision of IS 1742 - 1983 (code of practise for building drinage) complete. 110mm OD IS 4985 (10 Kg/cm2)

Description of Work / Item(s)

Amount

NETWORK SYSTEM

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. - 20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required - 25 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required - 32mm

Supplying and laying UTP CAT 6 (Systimax/CommScope) through the above PVC pipes / Raceways for data.

Supply and installation of RJ45 female jack (single plate).

Supply and installation of RJ45 female jack (double plate).

Installation and connecting of 24 port switch.

Supplying and installation of 24 port jack panel.

Supply and installation of 24U closed rack.

Supply and fixing 1 metre mounting cord (Systimax).

Supply and fixing 2 metre mounting cord (Systimax).

Termination and integration charges per set of nodes (Two ends) and testing, certification (Systimax) and documentation of all works.

Supply and installation of modular type single RJ-11 telephone socket housed in the manufacturers zinc passivated MS box with front plate.

Supply and installation of modular type dual RJ-11 telephone sockets housed in the manufacturers zinc passivated MS box with front plate.

Supply and installation of modular type RJ-45 box only housed in the manufacturers zinc passivated MS box

Supply and laying 30 pair krone connector housed in heavy duty ABS plastic mould with suitable locking arrangements.

Supplying and drawing following pair 0.5mm dia FRLS PVC insulated annealed copper conductor,unarmoured telephone cable in the existing surface /recessed steel/PVC conduit as required. - 30 Pair cable

Supplying and drawing following pair 0.5mm dia FRLS PVC insulated annealed copper conductor,unarmoured telephone cable in the existing surface /recessed steel/PVC conduit as required. - 20 Pair cable

Supplying and drawing following pair 0.5mm dia FRLS PVC insulated annealed copper conductor,unarmoured telephone cable in the existing surface /recessed steel/PVC conduit as required. - 10 Pair cable

PUBLIC ADDRESS SYSTEM

Supplying, installation, testing & commissioning of digital audio amplifier 160 Watts Mixing amplifier with USB at 240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of Table top gooseneck microphone with on/off switch

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. Speaker cable Four pair, 2-core, 1.5 sqmm

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

CCTV WORKS

Supply, laying, testing and commissioning for cat-6 4pair Networking cable for CCTV Cameras including termination and crimping through 25mm PVC conduit

Supplying and Installation of24Port POE Switch Unmanaged

Supplying and installation of 24 port jack panel.

Supply and installation of 9U closed rack.

Supply and fixing 1 metre mounting cord (Systimax).

Supply and fixing RJ45 Connectors (Metal Connector)

Supply and fixing CP Plus/Secureye / D-Link make IP Bullet camera 50 mt 2 Mega Pixel HD Camera

Supply and fixing of CP Plus/Secureye / D-Link make IP Bullet camera 20 mt 2 Mega Pixel HD Camera

Supply and fixing of CP Plus/Secureye / D-Link make IP cosmic/dome ccamera 20 mt 2 Mega Pixel HD Camera

Supply and fixing of CP Plus/Secureye / D-Link make IP night vision bullet camera 20 mt 2 Mega Pixel HD Camera

Supply and fixing of CP Plus/Secureye / D-Link 32 Channel HD Recording NVR with necessary required job etc...

Supply and fixing of CP Plus/Secureye / D-Link 8 Channel HD Recording NVR with necessary required job etc...

Supply and fixing of CP Plus/Secureye / D-Link 4TB HDD for Recording

EPABX

Supply of IP ready, Digital EPABX housed in a wall mounted rack, having ultimate capacity to connect with supply of 4 Digital Extension , 55 analog extensions with required number of ISDN PRI / extension cards including necessary hardware, Direct Inward Dialing and to support extensions with CLI & FSK technology including operator consoles with one digital KTS 12 keys (Operator Console), required MDFs with Krone type termination etc. The exchange having all the features as per Technical specification mentioned in Part –I of the tender, all complete. [Make: NEC / Alcatel / Avaya /cisco/Ppanasonic] With Rack, Mounting kits and all connecting Cords/Cables

Description of Work / Item(s)

Amount

Engineering Consultantion Charges Submission of Structural Design, Drawings, Bill of Quantities which are getting approval / vetting from the Government educational institutions / Government Research institutes SERC / IIT / NIT etc., and also preparing desing and detailed drawing for Electrical, Plumbing and submitting the same for the concurrence of Kamarajar Port. Note: The payment for this item will be paid on Milestone basis as stipulated in the Technical bid.

Description of Work / Item(s)

BoQ1 - Civil Works

BoQ2 - Electrical Works

BoQ3 - Plumbing Works

BoQ4 - Network System, Public Address System, CCTV, EPBAX

BoQ5 - Engineering and Design Charges

Bhamys Constructions Private Limited

Saga Infra Solutions

Saga Infra Solutions

Bhamys Constructions Private Limited

Bhamys Constructions Private Limited

Bhamys Constructions Private Limited