CLEANING AND REPAIR TO SEWAGE LINES SEPTIC TANKS MANHOLE AND REPAIR TO DRAIN CULVERT AND DRAIN CLEANING IN OMQ AND OTM ACCN IN ZONE C MARU VIHAR AT AF STN SURATGARH

Amount

BOQ (CLEANING AND REPAIR TO SEWAGE LINES, SEPTIC TANKS, MANHOLE AND REPAIR TO DRAIN, CULVERT AND DRAIN CLEANING IN OMQ AND OTM ACCN IN ZONE 'C' MARU VIHAR AT AF STN SURATGARH..)

Cleaning of all blockages of Nahani traps/floor traps/bottle traps, blockage of WC's, 100 mm dia CI pipe upto 1 st manhole/GT in shafts, vertical CI soil/waste pipe stacks, CI Tee/door bends etc to maintain internal sewage system by employing Safaiwala from 9:00 hours to 17:00 hours with permissible lunch break at Maru Vihar on daily basis with manual/pressure cleaning pump and flexible rods and other necessary mechanical equipments complete all as directed by Engr-in-Charge. Note :- (i) Supervisors should received everyday complaint through MES complaint register for Domestic Area maru vihar. (ii) Penalty in case not attending to each complaint during same working day will be recovered from contractor @ Rs. 350 per complaint. (iii)Quoted Rate included for all necessary T&P for mechanical cleaning/ manual cleaning shall be provided by Contractor. (iv) The Disposal of mud/silt, sludge & other debris retrieved form cleaning should be removed outside of MOD premises complete all as specified and directed by Engr- in Charge. (v) If necessitated as directed by JE/ Engr-in Charge/GE, contractor have to attend the complaints as required on Sunday/Holiday

Cleaning of manholes complete of any size and at any location incl taking out sludge and other material deposited in manhole and its removal to outside of MOD premises complete all as directed by Engr-in-Charge for depth of manholes n exc 1.00 M.

All as per item no 2 but depth of manhole exc 1.00 M & n exc 2.00 M

All as per item no 2 but depth of manhole exc 2.00 M & n exc 3.00 M

All as per item no 2 but depth of manhole exc 3.00 M & n,exc 4.5 m

Cleaning/Removal of sewage block in the existing line incl cleaning of complete line laid at any depth and removal of sludge/silt/liquid mud sand ( in foul condition) etc out of MOD premisses including testing of drains by filling the pipe with water, at any location between two consecutive manholes/gully trap to manhole incl testing the pipe by pouring water from manhole all as directed to the entire satisfaction of Engr-in-Charge for 150mm bore SGSW/RCC pipe / DWCP pipe.

All as per item no 6 but 200mm bore SGSW/RCC Pipe / DWCP pipe

All as per item no 6 above but 300mm bore SGSW/RCC Pipe. Note:- (a) No manual scavrage should be carried out for sewer line cleaning & blockage removal. (b) sewage blockage, it should be done throw extendable iron rode. (c) While cleaning of blocked sewage lines, the cutting & jetting machine required should be provided by contractor at his own arrangement for removal of blockage of sewer line cleaning, no extra amount shall be admissiible on this account. (d) During sewage cleaning work all sefety precautions like safety belt, safety cap,hand globes, oxygen cylinder & masks etc should be provided by contractor to labour.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in soft loose soil complete all as specified and directed.

All as per item no 9 above but exc 1.5 m and n exc 3.0 mtr depth as in soft loose soil .

Returning, filling in,including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft loose soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D2 (using 40 mm graded stone agg) as in foundations, filling and mass concrete complete all as specified and directed.

M&L PCC 1:2:4 type B1 (using 20 mm graded stone agg ) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M&L for cement concrete 1:2:4 (type B1 using 20 mm graded stone agg) as in copings, kneelers, apex stones, bed plates, kerbs lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, not provided including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

Demolition of Brick work masonry or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc,

M&L for brickworks wih subclass 'B' bricks straight or curvec on plan exc 6m mean radius built in CM 1;6 complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in CM 1:6 (except bricks) complete all as specified and as directed by Engr-in-Charge. Note- Bricks retrieved from items No 17 shall reused after proper cleaning.

Cutting and grubbing of bushes / shrubs /babool branches etc surrounding manholes,Gully trap ,wall pipe and sewage line alignment etc and levelling of ground around the manholes,sewage line and finish the surface of wall and removing the waste material to a distance exc 50m and n exc 500m and clearing the site. Note :- (i) All T&P (like JCB etc ) and equipment’s required for clearance of site, safety requipment shall be arranged and made available by the contractor. ii) All safety measures for workmen to do work shall be provided by the contractor. (iii) If any existing govt assets(Like electric cables,water pipeline, storm water drain boundary walls etc) are damages during the site clearance /excavation contractor should repair the same within time without any delay at his own cost .

Demolition and breaking up drain pipes of internal dia 100mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar incl concrete bedding and haunching complete all as specified and directed.

Demolition and breaking up drain pipes internal dia 150mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar incl concrete bedding and haunching complete all as specified and directed.

Demolition and breaking up drain pipes internal dia 200mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar incl concrete bedding and haunching complete all as specified and directed.

Demolition and breaking up drain pipes internal dia 300mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar incl concrete bedding and haunching complete all as specified and directed.

M&L for double wall corrugated drain pipe DWCP (SN8) 120mm (OD)/100 mm (ID) diameter, (ISI marked) drain pipes including concrete bed to drain pipes including pcc 1:4:8 type D-2 using 40mm graded stone aggregate packing under and haunching against the sides of pipes after they are laid and tested incl fitting of same grade complete all as specified and directed.

M&L for double wall corrugated drain pipe DWCP (SN8) 180mm (OD)/150 mm (ID) diameter, (ISI marked) including concrete bed to drain pipes including pcc 1:4:8 type D-2 using 40mm graded stone aggregate packing under and haunching against the sides of pipes after they are laid and tested incl fitting of same grade complete all as specified and directed.

M&L for double wall corrugated drain pipe DWCP (SN8) 230mm (OD)/200 mm (ID) diameter, (ISI marked) drain pipes laid on pcc 1:4:8 type D-2 using 40mm graded stone aggregate as in bed and including haunching , laid in trenches and tested incl fitting of same grade complete all as specified and directed.

M&L for double wall corrugated drain pipe DWCP (SN8) 330mm (OD)/300 mm (ID) diameter, (ISI marked) including concrete bed to drain pipes including pcc 1:4:8 type D-2 using 40mm graded stone aggregate packing under and haunching against the sides of pipes after they are laid and tested incl fitting of same grade complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes of 100 mm bore, jointed in cement mortar and taking out of trenches, complete all as specified and directed.

S&F spun type , Cast iron soil waste and vent pipes 75 mm bore in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S&F spun type, Cast iron soil waste and vent pipes 100 mm bore in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S&F spun type , Cast iron soil waste and vent pipes 75 mm bore in any length with or without ears, with cement joints, fixed on walls complete all as specified and directed.

S&F spun type, Cast iron soil waste and vent pipes 100 mm bore in any length with or without ears, with cement joints, fixed on walls complete all as specified and directed.

S&F 75 mm bore cast iron Bends (any radius),complete all as specified and directed.

S&F 100 mm bore cast iron Bends (any radius),complete all as specified and directed.

S&F 75 mm bore cast iron Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) complete all as specified and directed.

S&F 100 mm bore cast iron Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 110mm PVC (SWR) WC connector with lip ring complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement for 75 mm dia complete all as specified and directed.

M&L for Salt-glazed stoneware gully traps, square or round mouthed, type 'P' size 100 x 100 mm complete all as specified and directed.

Cutting into existing manholes for 150 mm dia connecting new drains,or septic tank for removing existing branch drain, making good to pipe and rendering, cutting out existing branch channel (1/2 round )in cement concrete 1:2:4 type B-1 smooth finished and reforming as required ,complete all as specified and directed.

Cutting into existing manholes for 200 mm dia connecting new drains,or septic tank for removing existing branch drain, making good to pipe and rendering, cutting out existing branch channel (1/2 round )in cement concrete 1:2:4 type B-1 smooth finished and reforming as required ,complete all as specified and directed.

M&L for Stack clamps of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore pipe complete all as specified and directed.

M&L for Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm bore pipe complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified and directed.

M&L for 15 mm thick Rendering in CM 1:4 in Two Coat Ist Coat 10mm thick and Second Coat 5 mm thick using intergral water proofing liquid on brick masonry or other than fair faces of brick work & finishing the surfaces even & fair w/o using extra cement complete all as specified and directed.

M&L for 15 mm thick Rendering in CM 1:6 on brick masonry or other than fair faces of brick work & finishing the surfaces even & smooth w/o using extra cement complete all as specified and directed.

Supply only integral water proofing compound (ISI marked).

S&F precast steel fibre reinforced concrete (HD-20) manhole cover slab with frame conforming to IS-12592 (Pt I & II) complete all as specified and directed .

S&F Vitreous China Squatting pan, 'Orissa' pattern, size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe) in repair complete all as specified and directed by Engineer-in-Charge.

S&F Vitreous China wash down water closed pan (Pedestal pattern) white , including connection to drain(or out going pipe) and to flush pipe, antisypthonic (excluding flushing cistern and flush pipe) complete all as specified and directed by Engineer-in-Charge.

S&F 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets complete all as specified and directed by Engineer-in-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L glazed ceramic colour tiles in vertical surface of size 450 X 300 x 7 mm thick,over and including 10 mm thick cement palster in cm 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed by Engineer-in-Charge.

M & L non-skid ceramic tiles 7 to 8 mm thick area of each tile exceeding .06 sqm but not exceeding 0.11 sqm, in floors etc.laid over and including 15 mm thick cement screed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed by Engineer-in-Charge.

Demolition of RCC of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition)

M& L for providing precast cement concrete 1:2:4 type B1 (using 20mm graded aggregate) as in slab/manhole cover set in CM 1:4 complete all as specified and directed by Engr-in-Chage

S&F mild steel TMT bars 10 mm dia and over cut to length bent to shape required including cranking , bending spirally for hooping for columns hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia complete all specified and as directed.

S&F mild steel Framed work such as frames around manhole covers , rungs etc grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all specified and as directed.

Taking up or down 15 mm bore steel tubing with connections or fittings from wall, ceiling and floor etc., including cutting/chasing in wall/floor and removal from site, complete all as specified and directed by the Engineer in Charge.

Taking up or down 20 mm bore steel tubing with connections or fittings from wall, ceiling and floor etc., including cutting/chasing in wall/floor and removal from site, complete all as specified and directed by the Engineer in Charge.

S&F Steel water tubes, 15 mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors, complete all as specified and directed by the Engineer in Charge.

S&F Steel water tubes, 20 mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors, complete all as specified and directed by the Engineer in Charge.

S&F in repair Stop valve/Angle valve 15 mm dia cast copper alloy , screwed down chromium plated fancy type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge.

S&F in repair Pillar taps, 15 mm bore cast copper alloy chromium plated fancy type , with capstan heads, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed by the Engineer in Charge.

S&F in repair Bib taps,15mm bore cast copper alloy, with crutch or butterfly handle ,chromium plated ,fancy type ,screwed down , screwed for iron pipe , complete all as specified and directed by the Engineer in Charge.

S&F in repair PVC connection of 15 mm bore size with PTMT, non corrosive with nuts and washers on both ends,450 mm long , complete all as specified and directed by the Engineer in -Charge

S&F PVC waste pipe for WHB including all fittings fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

De-watering and Sludge of septic tanks/soakage wells and sewage line by pumping with trolley mounted pump sets including carrying the waste water in closed containers and unloading it out side the MoD land at location shown by Engr-in-Charge at a distance n exc 10 KM from the starting point including removing the existing manholes cover and replacing the same, septic tanks/soakage wells of any size/ depth complete all as specified and as directed by Engr-in- Charge. Note :- (i) Hydraulically driven high pressure pump, capacity of 295L/min at 135 bar. (ii) Hydraulically driven high pressure pump, having 1850 cum/hr suction pressure. (iii) Rear hydraulic driven hose reel with 120m jetting hose. (iv) Proper safety of the operator during operation.

Cleaning of Grease trap tank by taking out the sludge mud /silt etc and removing of MOD premises complete all as specified and directed by Engr-in- Charge.

Demolition of cement concrete in ground floors and paving not exceeding 15 cm thick (below or above the gruound level) complete all as specified and directed.

M&L for 75mm thick cement concrete type B-1 1:4:8 (using 20mm graded crushed stone aggregate) as in sub base complete all as specified and as directed.

M&L for heavy duty vitrified coloured paving tiles of size 300 mm X 300 mm x 7-8 thick exterior grade set and jointed with neat cement slurry and pointed in coloured or white cement to match the shade of tiles,including 15mm thick screed bed of CM 1:6 for laying floor finishes complete all as specified and as directed.

M&L for brickwork with subclass 'B' bricks straight or curved on plan exc 6m mean radius built in CM 1:4 completed all as specified and directed by Engr-In- Charge.

M&L for brickwork with subclass 'B' bricks straight or curved on plan exc 6m mean radius (Except bricks) built in CM 1:4 all as specified and directed by Engr-In- Charge. Note : Servicable bricks retrived from serial no 17 above shall be used after proper cleaning.

M&L for PCC 1;2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in coping, benching etc complete all as specified and directed.

M&L 75mm thick PCC 1:3:6, type C-2 (40 mm graded agg) as in path, Hardstanding, plinth protection and similar work complete all as specified and directed.

M&L for Rendering 15mm in cement mortar 1:4 on fair faces of brick/concrete surface including finished even and fair without using extra cement complete all as specified and directed by Engr-in-Charge

Excavation of silt and liquid mud etc in foul condition in existing open drain, cleaning of debris, garbage material, deposited soil, uprooting of plant from drain and cleaning the drain upto 1.5M depth & removal of debris /garbage material including taking out and removal of excavated material to a distance exc 1.5 Km and n.exc 5 Km and deposited where directed complete all as specified and directed by Engr-in-Charge

Cleaning of debris, garbage material, deposited soil, uprooting of plant from culvert drain pipe upto dia 1.5M depth & removal of debris /garbage material to distance exc 1.5 Km and n.exc 5.00 Km complete all as specified and as directed.

M&L factory made Machine pressed precast concrete interlocking paver block any shape or size conforming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and no pigment laid over 25mm thick sand cushioning including dismentling of old U/S paver block complete all as specified and directed by Engr-In-Charge.

M&L for providing reinforcement cement concrete type B1 1:2:4 (using 20mm graded stone agg) as in slabs supported on walls, beams and column in floors balconies,canopies, desc slabs and the shelves and the like complete all as specified and as directed by Engr -in -Charge

Use and waste form work to edge of concrete flats, breaks in floors, opening in concrete walls,floors and roofs and side of RCC/PCC bands in walls and similar works exc 10cm but n exc 20cm thick, complete all as specified and as directed by Engr -in -Charge

S&F mild steel TMT bars 6 to 8mm dia , cut to length, bent to shape requred, including crakcing bending spirally hooping for columns and binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and as directed by Engr -in -Charge.

Contract Amount shall be derived after deducting the amount of Schedule of Credit in General Summary on serial page No 17 of tender documents.

SHIVA BUILDERS

MISHRA CONSTRUCTION COMPANY