C/O Toilet Block for Person with disabilities/transgender in the premisses of Court Complex at Theog Distt. Shimla, HP

Excavation in soil in Hilly Area by manual means including cutting and trimming of side slopes and disposing of excavated earth with a lift upto 1.5 m and a lead upto 20m as per drawing and Technical Specification clause 1603.1 with in all leads and lifts as per the direction of engineer-in Charge.

Excavation in foundations, trenches etc., in earth work,i lift upto 1.50 mtr. height, stacking the eacavated soil not more then 3 mtr. clear from the edge of excavation and then returning the stacked soil in 15cm. (fifteen centimeter) thick layers, when required in to plinth, sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per direction of Engineer-in-charge within all leads and lifts.

Filling in plinth with boulder under floor including watering ramming consolidating and dressing complete for all floors

Providing and laying cement concrete 1:6:12. (One cement: six sand : twelve graded stone aggregate 40 mm nominal size) and curing complete excluding cost of centring and shuttering in foundation and plinth . including all leads and lifts and carriage of materials and other incidentals.

Providing and laying cement concrete 1:4:8. (One cement: four sand : eight graded stone aggregate 40 mm nominal size) and curing complete excluding cost of centring and shuttering in foundation and plinth . including all leads and lifts and carriage of materials and other incidentals.

Providing and Fixing weapholes in Brick masonary/stone masonary plain RCC abutment ,B/wall, R/wall with 100mm diapipei/c all leads & lifts.

Providing form work with steel plates 3.15mm ( three point fifteen millimetre) thick welded with angle iron in frame 30x30x5mm ( thirty x thirty x five millimetre).so as to give a fair finish including centering, shuttering, strutting and propping etc. in any height/depth of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in :-Flat surfaces such as soffits of suspened floors, roofs, landings and the like floors etc. upto 20mm in thickness

b) Vertical surfaces such as wall

Edges of slabs and breaks in floors and walls: Under 20 cm. wide.

Providing and laying cement concrete work 1:1.5:3 (1 Cement:1.5 Sand:3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in :Suspended floor roofs, landing and shelves and their support balconies, beams, girders, bressumers and cantilever upto floor two level.

b) Vertical surfaces such as wall

Providing and laying cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) upto all floor level cement concrete 1 : 2 : 4 in string courses, copies, bed plates,anchor block, plain windows sills & the like.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to floor two level including carriage of materials within all leads and lifts and other incidentals.

Brick work using common burnt clay building bricks in cement mortar 1:6 (1 cement :6 sand) 2nd Class in foundation and plinth Brick work using common burnt clay building bricks in cement mortar 1:6 (1 cement :6 sand)

Brick work using 2nd Class common burnt clay building bricks in super structure upto all floor level in cement mortar 1:4 (one cement :four sand) including carriage of materials within all leads and lifts and other incidentals.

Providing & fixing powder coated anodized aluminium work for frames of doors, windows, ventilators and partitions with extruded built up standard tubular and other sections of approved make confirming to IS 733 and IS 1285 anodized transparent or dyed to required shade according to IS 1868 ( Minimum anodic coating of grade AC 15 ) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, stright, mitred and jointed mechanically where ever required including cleat angle, aluminium, snap beading for glazing/ panelling C.P. brass/ Stainless steel screws. All complete as per Architectural drawing & the direction of Engineer-in-Charge.For doors, windows & ventilators & glazing partitions frames as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

For shutters of doors, windows & ventilators including providing & fixing hinges/ pivots & making provision for fixing of fittings where ever required including the cost of PVC/ Neoprene gasket as required ( fitting & glazing/ panelling shall be paid for separately ) as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing glazing in aluminium doors, windows, ventilators shutters & partitions etc. with PVC/Neoprene gasket etc. complete as per the Architectural drawing & the direction of Engineer-in-Charge ( Cost of aluminium snap beading shall be paid in basic items ) glazing with glass panes of 5.50 mm ( Five point five milimeter ) thickness ( Weight not less than 13.75/Kg ( Thirteen point seven five kilograme ) per Square meter as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing satinless steel wire mesh shutters in aluminium doors,windows, ventilators shutters and partitions etc. with PVC neoprene gasket etc. complete as per the Architectural drawing & as per direction of Engineer-in-Charge (Cost of snap beeding shall be paid in basic items) as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

P/F 12 mm thick prelaminated board both side bwp phenol bonded exterior/interior grade panalled shutters with frame of first class deodar wood for doors including bright finished/black enamelled iron butt hinges with necessary screws 40 mm thick frame.

Providing and fixing anodized aluminum sliding door bolts anodized transparent or dyed to required shade with bolt and nut and screws etc. 250 mmx16mm

Providing and fixing anodized aluminum tower bolts (Barrel type) anodized transparent or dyed to required shades and color with screw etc. complete 200x10mm (two hundred x ten millimeter)

Providing and fixing aluminum handles anodized transparent or dyed to required shades and color with screws etc. complete 125mm (one hundred twenty five millimeter)

75 mm (Seventy five millimeter)

Providing and fixing 10mm thick antiskid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalent 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3(1cement:3sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete.

Providing and laying Duro stone vetrified tiles (300x300mmx8mm) in grey/coloured of required shade in skirting risers of steps and dados on 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete 150mm dia pipes

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete(i) PVC plan bend 100/150mm dia

ii) PVC shoe 100/150mm dia

Providing and fixing m.s.holder bat clamps of approved design to C.I. or S.C.I pipes embeded in and including cement concrete blocks 10 x10x10 cm of 1:2:4:mix (1 cement 2 sand 4 stone graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the wall etc 150 mm diametre

6mm thick cement plaster to ceiling in cement mortar 1:3 (1cement :3sand) including carriage of materials within all leads and lifts and other incidentals.

15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. in cement mortar 1:6 (one cement :six sand)

15mm Cement plaster in single coat on the fair side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. in cement mortar 1:6 (one cement :six sand)

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equivalent on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1cement : 3:sand :6 graded stone aggregate 20mm nominal )including finishing the top surface of concrete smooth

Providing under layer for plinth protection of 75mm thick (un consolidation) bed dry bricks/stone aggregate 40mm nominal size) well rammed and consolidating and grouted with fine sand including preparation of ground

W.S & S.I :-Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450 ,2004 of Kitec or its equivalent U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-incharge.1620 (20mm OD pipe)

2026 (25 mm OD pipe).

Providing and fixing PVC water storage tank of SINTEX ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level 1000 litres net capacity tank.

Providing and fixing vitreous China pedestal type water closet (European yype) Pluyo Ca no. 20065 of hindware with seat and lid ,10 lit. low level white vitrous china flushing cistern & CP flush bend with fittings & CI brackets 40mm flish bend ,overflow arrangement with specials of standard make and mosquito prooof coupfing of approved desing complete ,including painting of fitting and bracket s, cutting and making good the walls and floors wherever required.

Providing and fixing White vitreous china pedestal type water closet for specialy disable preson with seat and gd 10 white PVC flushing cistern ,including grab bars,flush pipe, with manually controlled device (handle bars confirming to is:7231 .with all fitting and fixtures complete including cutting and making dood the walls andfloors wherever required.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Single squatting plate with 5 liters C.I. automatic flushing cistern

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers white plastic seat and cover

Providing and fixing PTMT Coloured / white automatic flushing cistern with a pair of PVC / C.I. or M.S. bracket complete with fittings including PVC syphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same ( over flow pipe to be measured and paid for separately 10 litres net capacity.

Providing and fixing PVC ‘ P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete 150 mm dia.

Providing and fixing PVC floor trap ISI marked of self cleaning design i/c fixing with approved adhesive,cost of cutting and making good the walland floor etc. complete (i) 110mm nominal size.

Providing and fixing vitreous China wash basin (under counter basin/Table Top basin) ofZEN Category No. 10049 size 56x43cm or its equivlant,ci bracket, 15mm CP brass piller taps/mixer ISI marked IS No. 8934 of jaquer or its equivlant, 32mm CP brass waste of standard pattern , i/c painting of fitting sand bracket , cutting and making good the walls wherever requir:(i) White vitrious china Wash basin with apair of 15mm CP brass piller basin mixer taps i/c carriage of material. ( with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings: Flat back 600mmx480mm

Providing and fixing Vetrious china wash basin with pedestal no.10001 of Hindwaer or its equivlant, ci bracket, 15mm cp brass single hole basin mixture of jaquar or its equivlant ISI marked IS no. 8934,32mmcp brass waste of standard pattern, i/c painting of fitting sand brackets, cuting and making good the walls wherever required:(i)white vitrious china wash basin code:LTS WHT-38801+LYS-WHT-38305 (Clair) of size550x400mm with pedestal of cera or its equivlant withpair of 15mm cp brass piller taps within all leads and lift.

Providing and fixing 8mm dia CP /SS jet with flexible tube of jaquar or its equivlant up to 1.00 metre long with SS triangular plate to European type WC of quality and make as approved by Engineer in Charge.

Providing and fixing 100mm C P grating for floor traps

Providing and fixing heavy duty ESS Grab Bars 12inch with screw fitting etc. of approved make for handicapped person i/c fixing complete i/c carriage of material in all leads and lifts.

Providing and fixing Indo Med Sanitary Pads Vending Machine (Manual), storage capacity 35 i/c all leads and lifts.

Providing and fixing 32mm dia lead waste pipe for wash basin or sink including brass check nuts.

Providing and fixing 600x450mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers.

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws : 600mm x 20mm

Poviding and fixing CP brass toilet paper holders.

Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws Glass container

Providing and fixing brass bib tap (Superior or heavy type) with capston head 15mm dia.

Providing and fixing C.P. connection pipe with brass union 45cm long 15mm nominal bore.

Providing and fixing Brass full way valve with wheel. (i) 15mm dia

ii) 20mm dia.

Providing and fixing Brass angle valve 15mm dia without nuts and pipes

Providing and fixing brass concealed stop cock with flange of approved quality and colour. Confoming toIS:8931 i) 15 mm nominal bore.

Providing and laying (to level or slopes) and jointing with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 sand) salt glazed stoneware pipes grade 'A' of the following internal diameters including testing of pipes and joints complete. 150 mm dia.

Providing and laying cement concrete 1:4:8 (1 Cement : 4 Sand : 8 graded stone aggregate 40mm nominal size ) bedding for stoneware pipes of the following internal diameters, necessary form work and curing complete for 150 mm dia pipe.

Construction manhole with RCC top slab 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing: (i) Inside size 800mm x800mm and 500mm deep including C.I. cover with frme( Light duty single seal pattern-1) For frme of internal diamensions 455mm x610rectangular C.I. Cover ( light duty single seat pattern (i) the weight of cover to be not less than 23 kg. (i) Inside size 800mm and 500mm deep including C.I. cover with frme (light duty single seal pattern-1) For frame of internal diamensions 455mmx610mm rectangular C.I cover ( light duty) single seat pattern (i) the weight of cover to be not less than 23 kg. (a) with 200mm thick wall of brick msonry using ommon brunt clay building bricks in cement mortr 1:3 ( 1cement:3san)

Supplying and fixing C.I. Cover 300mmx300mm with frame for gully trap standard pattern. The weight of cover to be not less than 4.53 kg.

Providing and fixing wash basin for specially disabled persons with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including grab bars, painting of fittings and brackets, cutting and making good the walls wherever required, including carriage of all labour equipment and material various location through all modes of transportation in all leads ifts and all incidental charges .