REPAIRS/REPLACEMENT OF WOODEN, STEEL AND UPVC JOINERY, CURTAIN RODS IN SECTOR 47 AT BRD UNDER GE (AF) MC CHANDIGARH

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but not exc 4 Sqm each and removing from site complete all as specified and directed.

Taking down shutters of any description not exc 1.00 sqm each and removing from site complete all as specified and directed.

Taking down shutters of any description exc 1.00 sqm but n. exc. 2 Sqm each and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutters exc 1.5 sqm but not exc 4 Sqm each and removing from site complete all as specified and directed. Note:- Shutter obtained from this item shall be re-used in item No 8.

M&L for 2nd class hard wood, plain, solid, straight chowkhats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

Taking down shutters for Resecuring of any description exc 1.00 sqm but n. exc. 2 Sqm each and refixing in same opening, complete all as specified and directed.

M&L for refixing old wooden shutter exc 1.0 Sqm but n.exc 2.0Sqm in same opening as obtained from item No. 5 here-in-above, complete all as specified and directed.

M&L for Cutting holes through brick wall built in cement mortar, for inserting holdfasts, depth of embedded portion of holdfasts exceeding half brick thick but not exceeding one brick thick and making good the dismantled portion with PCC type B-0, (1:2:4) and cement mortar (1:3) to match the disturbed surface with existing finish, complete all as specified and directed.

M&L for Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work n.exc 15 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc. complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube in opening complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M. S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S&F powder coated pressed steel frame for doors with double rebates of size 125 x 60mm made with steel sheet of 1.25mm thickness in and including necessary fixing lugs, hinges lock strike plate complete all as specified and directed.

S&F powder coated pressed steel frame for doors with single rebates of size 105 x 60mm made with steel sheet of 1.25mm thickness in and including necessary fixing lugs, hinges lock strike plate complete all as specified and directed.

M&L for providing cement concrete type C-0 (1:3:6) using 12.50mm graded aggregate as in pressed steel door frame (backfill) complete all as specified and directed.

S&F for 35 mm thick 2nd class hard wood plain, framed paneled shutters (two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I), kiln seasoned and chemically pressure treated (factory made shutters) complete all as specified and directed.

S&F for 35 mm thick 2nd class hard wood plain, framed flush shutters, solid core construction with block boards core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L for factory made 2nd class hardwood (Hollock) glazed & skeleton shutters, 35mm thick open rebated and prepared to receive wire cloth, glass, gauze etc. with sash Bars, divided of framing plain chamfered or rounded, fitted with cut and metred beads off securing glass, gauze etc ( not more than 350mm center to center ) sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(a), complete all as specified. NOTE : Wire gauge shutter should also have the provision of vertical member of size 100mm 35mm at middle of the shutter. The vertical member have mitred joints and shall be stuck tenoned to the depth not less than 35mm in top, lock & bottom rails and have rebate to receive the wire gauge etc. complete all as specified and directed.

M&L for Factory made box type steel window composite type with double rebated pressed steel frames 80 mm x 60mm (Peripherral) and 80x75mm (Intermediate members) made out of cold rolled 1.25mm thick sheet having steel window/vertilators shutter of MS tubular section of size 50mm x 20mm x 1.10mm thick fixed with box type hinges including 8mm x 8mm MS hollow tubular section as beading for glazed and wire shutter handle of 100mm size made out of Z section 01 No, MS stove enamelled black tower bolt of size 120mm 02 Nos, 150 mm mild steel hooks and eyes each sutter flat iron 40mm x 1.25mm and 200mm long hold fasts 04 Nos each window including necessary filling hollow frame with PCC (1:3:6), cutting holes in wall, making good with existing surfaces as per specifications and including 10mm x 10mm mild steel square bars as grill fixed to window/ventilator frame using welding complete all as specified and directed.

S&F in repair framed work such as supports of gates, windows grill and cooler stand and similar work for window etc conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F in repair mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wind ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers, kitchen cabinet holdfasts and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F in repairs 18/19 mm thick block board grade 2 interior grade commercial type with decorative face including fixing 18 mm wide 6 mm thick beading all around of 1st class HW (Teak) complete all as specified and directed.

S&F in repair Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flap when open 30mm complete all as specified and directed.

S&F in repair aluminium channel of size 450x25mm complete all as specified and directed.

S&F for stainless steel butt hinges medium weight size of hinges is 100 mm complete all as specified and directed.

S&F to Aluminium, anodized, barrel tower bolts of extruded section. Length of bolt is 150mm complete all as specified and directed.

S&F to mild steel, barrel tower bolts of extruded section. Length of bolt is 200mm complete all as specified and directed.

S&F 300mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed

S&F 125 mm long extruded aluminium alloy, handles, fabricated type, anodized, complete all as specified and directed.

S&F 150 mm long mild steel pressed, handles, fabricated type, complete all as specified and directed.

M&L for welding in repairs exc 2.5 cm but n. exc. 5 cm in length, thickness of metal to be welded exc 6 mm but n. exc. 9mm complete all as specified and directed.

S&F in repair 125 mm size hasp and staple safety type aluminium anodized complete all as specified and directed.

S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.

S&F in repair magnetic catcher for kitchen cabinet and cupboards complete all as specified and directed.

Hacking out old broken glass (any thickness) from wooden/steel frames, glazed with putty of fixed with screws complete all as specified and directed.

S&F sheet glass ordinary quality and glazing with oil putty in squares n. exc. 0.5 Sqm in each pane of thickness 4.0 mm complete all as specified and directed.

S&F sheet glass ordinary quality and glazing with oil putty in squares exc. 0.5 Sqm in each pane of thickness 4 mm complete all as specified and directed.

S&F Figured glass, pinhead type and glazing with oil putty in square exc. 0.5 Sqm in each pane of thickness 4.0 mm complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staples, fixed in repairs, complete all as specified and directed. complete all as specified and directed.

S&F Galvanized stainless steel cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples, fixed in repairs, complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F in repair 300 mm mild steel ordinary rat tail rod pattern springs, including roller & roller plate complete all as specified directed by Engr-in-charge.

S&F in repair Floor door stopper of Aluminium alloy body anodised with hard drawn steel spring 140mm size fixed in floor complete all as specified directed by Engr-in-charge.

M&L for rendering 15mm thick in cement mortar 1:4 on walls of surfaces finished even and smooth without using extra cement including taking down old plaster and removal of unserviceable material out side MoD land upto distance exceeding 1.5Km but n.exc 2Km complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on walls of surfaces finished even and smooth without using extra cement including taking down old plaster and removal of unserviceable material out side MoD land upto distance exceeding 1.5Km but n.exc 2Km complete all as specified and directed.

M&L for prepartaion of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for prepartaion of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

S & F in repair mortice lock, vertical type size 100 mm brass 6 lever complete all as specified and directed.

S&F in repair 25mm dia, 0.50mm thick, MS drapery rod with PVC coating including bracket, wall to wall and side doms, complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exceeding 15cm thickness (below or above ground level) and removing the same and deposited complete all as specified and as directed by Engineer in charge

M&L for 40mm thick PCC type B-1 (1:2:4) using 20mm graded stone aggregate as in floor and making surface good with using extra cement, complete all as specified and directed.

M&L for glass dividing strips 3mm thick 28mm wide in floor finish sub laying panel, complete all as specified and directed.

Material and labour for 100mm thick PCC 1:2:4 type B-2 using 40mm graded stone aggregate as in flooring, finished even and smooth using extra cement, complete all as specified and directed.

Material and labour for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, complete all as specified and directed.

M&L for First Quality, Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in floors, in neat cement slurry and pointed in white cement to match tiles including 15mm thick screed in cement mortar 1:6 including dismantling old tiles and removal of unserviceable material out side MoD land upto distance exceeding 1.5Km but n.exc 2Km, complete all as specified and directed.

M&L for First Quality, Glazed ceramic coloured tiles 7mm thick (rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.16 sqm, as in skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles including 10mm thick rendering in cement mortar 1:4 including dismantling old tiles and removal of unserviceable material out side MoD land upto distance exceeding 1.5Km but n.exc 2Km , complete all as specified and directed.

S&F in repair aluminium powder coated Door seal steel strips with brushes of size of not less than 40mm wide, fixed to wooden doors complete all as specified & directed.

S&F in repair Aluminium, anodized, barrel tower bolts of extruded section. Length of bolt is 200mm complete all as specified and directed.

S&F in repair Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F in repair mild steel butt hinges medium weight size of hinges is 100 mm complete all as specified and directed.

S&F in repair 100 mm long mild steel pressed, handles, fabricated type, complete all as specified and directed.

S&F in repair 125 mm long mild steel pressed, handles, fabricated type, complete all as specified and directed.

S&F in repair 250mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S & F in repair mortice lock, vertical type size 100 mm brass 6 lever complete all as specified and directed.

S & F in repair aluminium sheeting 0.50mm thick fixed to wooden shutter with nails including cutting to required size complete all as specified and directed.

Dismantling post or struts (wood, steel or RCC embedded in concrete block of any section including taking out embedded portion and making good disturbed ground, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness etc in roof coverings, ridge, gutter complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi-corrugated etc) sheets in roof coverings , complete all as specified and directed.

Supply and fixing mild steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of grade Fe 410 -W (Gde- E- 250) quality- A , complete all as specified and directed.

S&F Pre painted Coloured Galvalume roofing system sheet 0.50 mm thick, corrugated sheet having Zinc aluminum alloy coating AZ150 shall be as per IS:277/ASTM 1379 150 gsm/ sqm double ribbed trapezoidal profile steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws, complete all as specified and as directed.

Supply and fixing, 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in roofs, walls etc. with grade of zinc coating 120 GSM , complete all as specified and directed.

All as per item No. 74 above but except sheets.

Supply and fixing 2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with L-type or J-type or cranked hook bolts in lieu of screw , complete all as specified and directed.

Supply and fixing 1.25mm thick Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type including dismantling old complete all as specified and directed.

Demolition of brick masonry work built in cement mortar including all quoins, arches, pillars, staging etc. and removal of rubbish outside MOD land and stacking of useful bricks/brickbats for reuse or credit, complete all as specified and directed

Material and labour, brick work with fly ash bricks straight or curved on plan exceeding 6m mean radius, built in CM (1:4), complete all as specified and directed.

Material and labour, brickwork with using retrieved subclass 'B' old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:4), but except bricks, complete all as specified and directed. Note : Old serviceable bricks retrieved from demolition vide srl item No 78 here-in-before shall be reused after proper cleaning & washing etc.

M&L for machine cut kota stone slab flooring 18-20 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, laid over 20 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes including dismantling and removal of unserviceable material out side MoD land upto distance exceeding 1.5Km but n.exc 2Km complete all as specified and as directed.

M&L for machine cut kota stone slab in riser of steps, skirting, dado, 18-20 mm thick over & including 10 mm thick rendering in cement mortar 1:4, laid & jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, including dismantling and removal of unserviceable material out side MoD land upto distance exceeding 1.5Km but n.exc 2Km complete all as specified and as directed.

S & F in repair pre laminated board 18/19mm thick exterior grade, prelaminated both side with decorative choice lamination including 1st class hard wood leaping 3mm thick all around board, fixed with nails/screws to timber frame complete all as specified and directed.

Note:- Amount of credit of Rs.108256.00 for retrieved materials is mentioned in Schedule of Credit of tender documents in pdf form which will be deducted offline while acceptance of tender.

R R Traders

KUMAR AND COMPANY

Supreet Associates

Bharat Enterprises

MOHAMMAD RASHID