SPECIAL REPAIR TO BLDG NO. P-74 AT (SINGLE JCOS LIVING ACCN) OF 993 AD REGT WKSP UNDER GE(ARMY) DHAR ROAD UDHAMPUR

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-Charge.

Dismantling of brick work or stone masonry built in cement mortar including all quoins arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed by Engr-in-Charge

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level), complete all as specified and as directed by Engr-in-Charge.

Demolition of cement concrete of any description in any position not specifically provided for complete all as specified and as directed by Engr-in-Charge.

Dismantling of cast iron or reinforced concrete drain pipes including fittings and accessories, 100/75mm dia and in any position complete all as specified and as directed by Engr-in-Charge.

Dismantling water tanks and removing to store exc 500 ltrs but not exc 1000 Ltrs capacity complete all as specified and as directed by Engr-in-Charge.

Demolition of cement concrete (Re-inforced) of any description and in any position complete all as specified and as directed by Engr-in-Charge.

Taking down chowkats with shutters without taking of shutters from the frames n. exc 1.50 Square metre each complete all as specified and as directed by Engr-in-Charge.

Taking down chowkats with shutters without taking of shutters from the frames exc 1.50 Square metre but n exc 4.00 Square metre each complete all as specified and as directed by Engr-in-Charge.

Brick work with old size, sub class `B' bricks, straight or curved on plan exc 6m mean radius, built in CM(1:6) complete all as specified and as directed by Engr-in-Charge.

Brick work with old size, sub class `B' bricks, straight or curved on plan to any radius, as in half brick thick, built in CM(1:4) complete all as specified and as directed by Engr-in-Charge.

Factory made, 2nd class hard wood, 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass / gauge etc. (without sash bars) edges or framing plain, chamfered or rounded fitted with cut or mitered beads for securing glass etc. size of members of shutters as specified in SSR Part - I section 8.20 (a), all as specified and directed by Engr-in-Charge

Factory made, 35mm thick 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 12 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35 mm thick complete, all as specified and directed by Engr-in-Charge.

Factory made solid PVC Moulded frame 50x47mm made up 5mm colour single prelem PVC sheet and reinforced with MS aqure tube supplyin & fixing in opening acomplete all as specified and as directed by Engr-in-Charge.

Factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame made out of mild steel tubes for top and bottom rails . Mild steel frame shall be covered with heat moulded plain cover PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side and gap insert for top rail and bottom rail ; Paneling of plain colour PVC sheet to be fitted in the mild steel frame welded /sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement supplying and fixing in the frame at site as per specification clause No 8B.1 to 8B.10 and drawing on page No 146 of MES SSR-2010 Part-II.

S& F 18 mm thick PVC board plain in shelves and back side & partition complete all as specified and as directed by Engr-in-

Providing cabinet & shutters in required fix at site out of 18 mm thick PVC board one side laminated(wooden grain) and other side plain fitted to wall, the handle shall be febricated using adhesive, screwed and secure as required. All edges shall be covered with 1.5mm thick edges leaping tapes or 90 degree edge bent finish as per manufactures instructions complete all as specified and as directed by Engr-in-Charge.

2nd class hardwood small fittings n exc 200cu cm each such as brackets of any type , latch and hinge blocks, shaped door and window stops and the like incl, all necessary labours and butt hinge of size 40mm complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section with 200 mm long bolt, complete all as specified and as directed by Engr-in-Charge.

MS sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 300 mm long complete all as specified and directed .

Aluminium alloy butt hinges 100mm long with galvanised mild steel hinge pin type C 21 complete all as specified and directed .

MS butt hinges 75mm long medium weight, cold rolled mild steel etc complete all as specified and directed .

MS 300mm long ordinary rat tail rod pattern spring incl roller and plate complete all as specified and as directed by Engr-in-Charge.

Aluminium handles fabricated type, anodised, 150 mm size complete all as specified and directed .

150mm long Hasp and staple safty type brass including bolt to hinge plate and fixed with screwscomplete all as specified and as directed by Engr-in-Charge.

S&F in repair Tubular Towel rail 20mm dia, D type, 60cm long between flanges of brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleats complete all as specified and directed .

Galvanised mild steel wire cloth 0.46mm nominal dia of wire and avarage width of aperture 1.18mm complete all as specified and directed

Mild steel framed work such as grills, gratings etc, with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; and similar works confoRunning metreing to Fe-290 Gde E-165 complete all as specified and as directed by Engr-in-Charge.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all specified and as directed. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1517/15 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Steel ventilator made up of box steel section of 16 gauge MS Sheet frame, fixed type suitable to fix half portion wire cloth and half portion glass with suitable MS beading or flat or oil putty complete all as specified and as directed by Engr-in-Charge. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1517/15 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

S&F Pressed steel frames of size 105x60mm, made of 1.25mm thick sheet, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate incl filling hollow of frame with plain cement concrete type B0 (1:2:4 )(using 12.5mm graded aggregate ,etc complete all as specified and as directed by Engr-in-Charge.

S&F Pressed steel frames of size 125x60mm, made of 1.25mm thick sheet, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate incl filling hollow of frame with plain cement concrete type B0 (1:2:4 )(using 12.5mm graded aggregate ,etc complete all as specified and as directed by Engr-in-Charge.

Providing cement concrete Type B0, 1:2:4 (using 12.5 mm graded crushed stone aggregate) as nominal mix in lintels upto 1.5m clear span, cills, steps, parapets, copings, bed plates, and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work etc complete all as specified and directed.

Plinth protection 50 mm thick in PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate ) laid in alternate bays (not exceeding 2 Square metre each) finished even and smooth at top without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed by Engr-in-Charge.

25mm thick Plain cement concrete type B0, 1:2:4 (using 12.5mm graded stone aggregate) as in sub flooring, roof padding etc finished ever and fair complete all as specified and directed.

M&L for 1st/Premium quality glazed ceramic digital coloured tiles of size 250x 350x 7 mm/ 300X 450X 7mm thick as in vertical surfaces such as skirtings, dados etc set & jointed in neat cement slurry & pointed with white or coloured cement to match the shade of tiles including 10mm thick rendering in CM (1:4) complete all as specified and as directed by Engr-in-Charge. Make: KAJARIA/SOMANY/ORIENTor equivalent

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and existing felt , etc and brushing neat cement slurry with 3.00 Kg of cement per sqm complete all as specified and directed

15mm thick screed bed or bedding layer of cement mortar (1:4) for lying floor finish complete all as specified and directed

M&L vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Square metre, infloors etc. in set and jointed in neat cement slurry andpointed in white or coloured cement to match complete all as specified and as directed by Engr-in-Charge. Make: Kajaria /SOMANY/ORIENT or equivalent

M&L Vitrified tiles 10mm thick on vertical surfaces of wall set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick rendering in CM (1:4) backing of wall tiles such as dado/skirting in vertical surface complete all as specified and as specified.

Non skid ceramic coloured ceramic degital type tiles 7 to 8mm thick (squqare/ rectangular) area of each tile exc 0.06 Square metre but n.exc 0.111 Square metre in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:4) complete all as specified and as directed by Engr-in-Charge.

15 mm thick cement plaster in cement mortar 1:4 on roof surfaces finished even and smooth without using extra cement, after rushing neat cement slurry with 3.00 Kg of cement per sq m and using WPC all as specified dir3ected by Engr -in Charge.

Applying a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.20 Kg/Sqm and thereafter all as specified directed by Engr -in Charge.

Taking down cement plaster of any description incl racking out joints hacking for keys, scrubbing down with water complete all as specified and as directed by Engr-in-Charge.

15 mm thick cement plaster on fair faces of brick work in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

Rendering 15 mm thick on fair faces of brick work or cement concrete surfaces in cement mortar 1:4, finished fair and even without using extra cement incl mixing of water proofing compound complete all as specified and as directed by Engr-in-Charge. (Note: Water Proofing compound shall be measured and paid for separately)

Supply only liquid water proofing compound (Makes :Pidilite Industries / ImpeRunning metreo /Snowcem India Ltd / Sika )

M&L for 10mm thick cement plaster on brick or concrete surfaces, as in ceiling / facia / chajja etc. in cement mortar 1:3 finished even and smooth without using extra cement, all as specified .

Extra over rendering or plastering for work in isolated width or in widths not forming part of general plastering such as on bands, sunk panels, skirting, drip moulds and similar works exc 15 cm but n. exc 30 cm in width or girth complete all as specified and as directed by Engr-in-Charge.

Two coats of cement base paint over a coat of alkali resistant priming paint on new surfaces including preperation of newly plastered of walls surfaces complete all as specified and as directed by Engr-in-Charge.

Two coats weather coat paint (exterior emulsion) of approved colour including preparation of new plastred surface complete all as specified and as directed by Engr-in-Charge.

Applying two coats of OBD on walls including 2mm thick wall care putty, on new plasterd surface plastered surfaces, over a coat of cement primer complete all as specified and as directed.

Complete removal of existing treatment of walls surface complete all as specified and as directed.

Providing 3 mm thick wall care putty in two layers including prepration of new platered surfaces complete all as specifed and as directed.

Applying two coats of oil bound distemper on newly plastered wall surfaces including preparation complete all as specified and directed.

Preparing old decorated wall surfaces applying two coats of white wash on wall complete all as specified.

Preparing old decorated of ceiling surfaces applying one coat of white wash complete all as specified.

Preparing old decorated of ceiling surfaces applying three coat of white wash complete all as specified.

Preparation of new steel surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer red oxide complete all as specified and as directed by Engr-in-Charge.

Two coats of synthetic enamel paint exc 10 cm width or girth on wooden surface over a coat of pink primer incl prepartion complete all as specified and as directed by Engr-in-Charge.

4mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 Square metre in each pane complete all as specified and as directed by Engr-in-Charge.

Description all as per Item No 61 here in before but frosted glass complete all as specified and as directed by Engr-in-Charge.

Taking up or down steel tubing with connections for cleaning for prefixing or removing to store yard complete of bore 15mm, all complete all as specified and as directed by Engr-in-Charge.

Taking up or down steel tubing with connections for cleaning for prefixing or removing to store yard complete of bore 20mm, complete all as specified and as directed by Engr-in-Charge.

15mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings complete all as specified and as directed by Engr-in-Charge.

20 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings complete all as specified and as directed by Engr-in-Charge.

S&F in repair Bib taps,fancy type long body, fancy type, chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm, fixed in repair, complete all as specified and as directed by Engr-in-Charge.

S&Fixed in repair pillar tap chromium plated fancy type with capstan head lettered hot or cold screwed for iron pipe 15mm bore complete all as specified and as directed by Engr-in-Charge.

S&F in repair Stop valves/angle valves fancy type, chromium plated for iron pipe or for unions of bore 15mm and fixed, complete all as specified and directed.

S&F in repair Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300 gram) complete all as specified and as directed by Engr-in-Charge.

PVC connections 15 mm size with PTMT nuts of length 450 mm long complete all as specified and as directed by Engr-in-Charge.

S&F in repair Brass chromium plated shower rose 125 mm with arm, with or without swivel joints, any size incl fixing to steel pipe or union complete all as specified and as directed by Engr-in-Charge.

S&F in repair Vitreous china squatting pan of Orissa Pattern size 580x 440 mm white with PVC ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe fixed in repair including placing in position in floor and embedded in cushion of PCC 1:7:12 type E-1 complete all as specified and as directed by Engr-in-Charge. (Make: - Hindware/ Parryware/ Johnson )

S&F in repair vitreous china wash basin of size 540x440 white with oval shape fixed in counter with cutting proper fixing and jointing and moulding of marbel all as specified and directed including brackets, including cutting for and pinning in ends of bracket complete all as specified and as directed by Engr-in-Charge.

S&F in repair Soap dish chromium plated fixed with plugs brass screws, complete all as specified and directed.

Supply and fix PVC (Plastic polymer Cistern) valve less, Syphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as specified and directed.

Waste coupling, 32mm dia, of PTMT (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms)complete all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, 75mm diameter of outlet, as in repairs complete all as specified and directed.

PVC (SWR) pipes, type 'B' 75 mm external dia single socketed in any length with rubber joints, fixed to walls complete all as specified and directed.

PVC (SWR) pipes, type 'B' 75 mm external dia single socketed in any length with rubber joints, laid in trenches or in floors complete all as specified and directed.

PVC (SWR) pipes, type 'B' 110 mm external dia single socketed in any length with rubber joints, fixed to walls complete all as specified and directed.

PVC(SWR) bends suitable for 110 mm external dia complete all as specified and directed.

PVC(SWR) bends suitable for 75mm external dia complete all as specified and directed.

PVC (SWR) junction single, (single T) equal or unequal of 110mm dia complete all as specified and directed.

PVC (SWR) junction single, (single T) equal or unequal of 75mm dia complete all as specified and directed.

110 mm bore PVC (SWR) vent cowl suitable for 110mm bore of pipe complete all as specified and directed.

75mm bore PVC (SWR) vent cowl suitable for 75mm bore of pipe complete all as specified and directed.

Add to item No.83 and 84 if provided with oval access door complete all as specified and directed.

Add to item No.85 and 86 if provided with oval access door complete all as specified and directed.

Rotational moulded polyethylene water storage tank , two layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories (i.e GI nipples and Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of bore 20mm (Minimum weight 210 gram) etc), complete all as specified and as directed by Engr-in-Charge.

Ball valve, high pressure with PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or fixed of size 20 mm bore, fixed in repairs.(Min Wt 20mm- 210 gms) complete all as specified and as directed by Engr-in-Charge.

20mm PVC Nipple suitable for HDPE Water tank (Min Wt 15mm-38gms) complete all as specified and as directed by Engr-in-Charge.

S&F in Repair PVC waste pipe 800mm long suitable for 32mm dia waste coupling complete all as specified and directed.

MS PVC coated decorative mild steel curtain rod of 20 mm dia with brackets both side of globe of fancy type all as specified and directed by Engr-in-charge.

Dismantling of corrugated or semi corrugated steel sheeting, of any description, roof coverings all as specified.

Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of and colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified as directed.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified as directed.

Gun metal globe or gate valves high pressure with polythene float and fly nut complete screwed for iron pipe or for unions of 20 mm bore and fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Cutting chases for concealed water tubing or concealed conduitwiring, etc. and making good, cutting not exceeding 20cm girth in CM 1:3 complete all as specified.

75mm thick PCC (1:4:8) type B2 using 40mm graded aggregate as in sub base for floor or path complete all as specified as directed.

Sand filling in floors or paving incl watering, ramming/ rolling and finishing to required size/shape etc n exc 25cm thick high from base all as specified as directed

M&L paver block 60mm thick Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thick M-35 Grade with grey cement and pigment of any pattern as approved by GE and as per manufacture Instruction complete all as specified.

Pre cast cement concrete block masonry 1:2:4, type B-1, using 20mm graded stone agg with solid blocks , exc 10 cm in width and setting in CM 1:4 , complete all as specified and as directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by Engr-in-Charge.

Black garnite 18-20mm thick of any type work table rubbed ad polished for plate form and counter type for kitchen plate form in 18-20 mm thick kota stone machine cut and polished of approved colour ( Black zet with Granite polish) incl setting and jointing in neat cement slurry and pointed in coloured cement to match the services etc and including screed bed 15mm thick in CM 1:4 of marble on stairs etc complete all as specified and as directed by Engr-in-Charge.

Machine cut kota stone slab 20-25 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting,dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Dismantling wall and ceiling boards (fibre pulp, insulation etc) or insulation boards / slabs / blankets, any thickness, including cover fillets, complete all as specified and as directed by Engr-in-Charge.

Providing & fixing False ceiling with Gypsum based ceiling tiles (with aluminum foil on one side) of size 595 x 595 mm of thickness not less than 9 mm including with GI powder coated frame angle /tee grid frame work for ceiiling with following specfication (a) S&F Angle of side 25x25x1mm powder coated (b) 25x25x1 mm GI powder coated at Bottom tee as in main member (c) 25x25x1 mm thick GI powder coated at bottoam tee as in cross members (d) S&F 1.6mm dia GI wire suspenders alongwith adjustable clamps to maintains leveling inculding fixing to ceiling fasteners manufacturers instructions complete. MAKE: VINYL TOUCH of LaGyp (LAFARGE) or equivalent in GYPROC (SAINT GOBBAIN).

Water proofing treatment to floor & vertical surfaces of sunken portion complete comprising the following: - (a) After demolition of floor & lime concrete etc. remove all loose particles along with existing water proofing treatment (any no. of layers) with wire brushes and cleaning the surfaces with water. (b) Brushing cement slurry with 1.2 kg of cement per square metre duly blended with & including water proofing compound. (c) 15 mm thick (Average thickness) plaster in cement mortar (1:3) mixed with Water proofing compound on sunken surface including walls. The corner of sunken portion shall be rounded in concave shape and adequate slope shall be made during plastering to accommodate sump pipe and curing the sunken portion with water minimum for 48 Hrs by ponding. (d) Applying a coat of bitumen [email protected]/sqm and applying a coat of bitumen 85/25 grade @1.20kg/sqm, Applying self adhesive type APP based polymeric membrane minimum weighing not less than 3.6 kg/ Sq. m and minimum 3 mm thick reinforced with polyester non-woven fabric (weight not less than 150 gm/Sq. m) and applying a coat of 1.20kg/sqm bitumen 85/25 grade,(e) M&L for PCC 1:7 :12 for filling of sunken portion with 40mm grade bricks aggregate all as directed by the Engineer-in-Charge. MAKES of APP film: LAFARGE, TEXA, STP, BENGAL AQUAFLUX,lAFARGE, TEXA, STP, BENGAL AQUAFLUX.

Re-inforced cement concrete type B-1, 1:2:4 (using 20mm graded stone aggt) as slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, roof beam and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engr-in-Charge.

Mild steel TMT bar 6 mm to 8mm dia cut to length bend to shape required including cranking bending etc and mild steel wire not less than 0.9mm dia complete all as specified and as directed by Engr-in-Charge.

Taking down carefully copper /aluminium, point wiring (light, fan, socket or power) complete including fittings and fixtures such as light fittings, switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of wall, ceiling, floors etc, complete all as specified and as directed by Engr-in-Charge.

Point wiring with 1.5 Sqmm PVC insulated, unsheathed (FRLS) cable with multi stranded copper conductor wiring in and including PVC concealed conduit (ISI marked) 20mm dia and over, wall thickness not less than 2.00 mm thick , and all accessories for one light / fan controlled by one switch with 1.25mm thick pressed steel terminal anodized box concealed on walls, 3mm laminated plastic sheet cover for mounting of switches, socket outlet, regulator etc, fixed by suitable size of 4 Nos cadmium screws along with PVC insulated and unsheathed FRLS 1.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly, complete all as specified and as directed by Engr-in-Charge including cutting chases pinning in making good to facing and pointing in CM 1:3 to the ends or cutting chases for concealed conduit point wiring and making good disturbed surface complete. Cutting not exc 4 cm girth and 4 cm width. (Note : The rates for concealed type wiring shall deemed to include the cost of cutting chases in the wall by using elect cutter and making good the disturbed surfaces of wall by providing cement plaster and matching the surfaces by white/colour wash all as per existing finishes complete.)

All as per description of Serial item No 117 here-in-before but one bell point controlled by one switch complete all as specified and as directed by Engr-in-Charge.

All as per description of Serial item No 117 here-in-before but one 3/5 pin 5 Amp switch socket outlet on independent board , complete all as specified and as directed by Engr-in-Charge.

All as per description of Serial item No 117 here-in-before but one 3/5 pin 5 Amp switch socket outlet on same board , complete all as specified and as directed by Engr-in-Charge.

All as per description of Serial item No 117 here-in-before but one 3/5 pin 15 Amp switch socket outlet on independent board with PVC insulated, unsheathed FRLS cable 2.5 Sqmm copper multistrand conductor, along with PVC insulated and unsheathed FRLS 1.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly complete all as specified and as directed by Engr-in-Charge.

Switch piano flush button single pole one way 5/6 Amp, 240 Volts, complete all as specified and as directed by Engr-in-Charge.

Bell push flush type 5 Amps 230 AC single pole type one way complete all as specified and directed.

Electric bell Ding Dong AC 230 volt single pole complete all as specified & directed.

S&F switch Socket outlet 3 pin 5 Amps flush type, multi pin complete all as specified & directed. ,

Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Block, complete all as specified and as directed by Engr-in-Charge.

PVC lamp holder insulated body bracket holder/Angle holdercomplete all as specified and as directed by Engr-in-Charge.

Switch socket combination, 2 in 1, 3/5 pin, 5/6 & 15/16 Amp flush type, complete all as specified and as directed by Engr-in-Charge.

Fan regulator 80W, 230V 50 Hz, mini rotary type electronic, step type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and as directed by Engr-in-Charge.

Taking down old unserviceable light fittings of any type and wattage complete all as specified and as directed by Engr-in-Charge.

S&F LED light fitting 1 x 18 watt including lamp, with new generation energy saving & environment friendly long life square TL 6500K including all accessories conforming to cat part No. SSK-SQ 1801 of make Syska or equivalent in performance of make specified in particular specifications etc including taking down old unserviceable fittings complete all as specifed and as directed by Engr-in-Charge. NOTE- (i) A certificate from the manufacturer for warranty minimum upto 3 years shall be obtained and submitted to the AGE/GE (ii) Any touch up of the wall surface due to changing of fittings shall be done by contractor with similar surface finish without extra cost to the department.

Supply & fixing 1x9 watt LED Bulk Head Light energy saving with IP65 with opal diffuser, pressure die cast aluminium housing & ring for sturdiness & corrosion resistant, epoxy powder coated, isolated driver, with system efficacy ≥ 100 Lm/watt, operating voltage 170-240 volt, colour temp 6500K, Low heat generating LED (Make of LED shall be CREE/Nichia/Osram) complete making all connection using 1.5 sqmm copper conductor multi strand PVC insulated 2 core flexible cable from ceiling rose to fitting complete all as per the directions of Engg-in-Charge including taking down old unserviceable fittings. NOTE- (i) A certificate from the manufacturer for warranty minimum upto 3 years shall be obtained and submitted to the AGE/GE (ii) Any touch up of the wall surface due to changing of fittings shall be done by contractor with similar surface finish without extra cost to the department. Make – Syska LED Cat Part No. SSK-BH-9W/ Havells Cat Part No. LHEOAOP7UZ6W010/ Surya Cat Part No SLE BLH 10 W or equivalent in performance of makes as specified in particular specifications.

Taking down old unserviceable sub main wiring of any size and type complete all as specified and as directed by Engr-in-Charge.

Supply, fix and connecting in replacement of sub main wiring complete with two runs of 4 sqmm single core PVC insulated heavy duty ISI Marked , unsheathed cable 1100 volts grade, multistranded with copper conductor drawing in PVC conduit and including provision of PVC insulated heavy duty ISI Marked , unsheathed cable 1100 volts grade 2.5 sqmm cpper conductor multistrand for earth continuity conductor and making good the disturbed surfacesto match with exisiting surfaces complete all as specified and directed. Note:- 1. (For measurement purpose 2 run of 4 Sqm + 1 run of 2.5 Sqmm shall be measured as one unit). 2. PVC conduit shall be measured and paid for separately.

Sub main wiring with two runs of 6 Sqmm ( 2x6 sqmm ) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including concealed non-metalic PVC rigid conduit 25 mm dia ISI marked with all conduit accessories mounting on surface of walls /roofs / ceiling etc with one run of 4 Sqmm (1x4sqmm ) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire, fixed in repair, complete all as specified and directed by Engr-in-Charge. Note:- 2 runs of 6 Sqmm (2x6sqmm ) ,one run of 4 Sqmm (1x4 sqmm ) cable and one metre of concealed conduit will be measured as one unit.

Taking down and disconnecting old unserviceable sheet metal enclosures of MCB any type and capacity complete all as specified and as directed by Engr-in-Charge.

Sheet metal enclosures for distribution board when MCB to be used SPN 08 way with IP-43, IK-09 protection 240V with 200 Amps rated bus bar, double door type including cutting chases in walls for fixing DBs making good the distubed surfaces to match with existing specifications including taking down old unserviceable DBs with accessories complete all as specified and as directed. Make: Havells Cat Part No. DHDNSHODDW08 or equivalent in performance of makes as specified in particular specifications.

MCB SPN 63 Amps, 240 Volts, rupturing capacity 10 KA "B" Series including providing aluminuium thimbles for outgoing cable, complete all as specified and as directed by Engr-in-Charge.

MCB SP,6 to 16 Amps, 240 Volts, rupturing capacity 10 KA "B" Series including providing aluminuium thimbles for outgoing cable, complete all as specified and as directed by Engr-in-Charge.

Geyser (Water heater) of 25 Ltrs capacity having 5 star rating 240 volt fixing with the help of washer, grouting bolts/nuts etc alongwith connection of geyser inlet and outlet by PVC flexible connection pipe with two brass adopter for carrying hot water complete all as specified and as directed by Engr-in-Charge.

Exhaust fan 450mm sweep 1400 RPM 230 volt, single phase with louvers and connection with 3 core suitable size copper conductor including making hole of required size and making good the disturbed surface complete all as specified and as directed by Engr-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.0mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 mtr below normal ground level, connected to and including 4 mm dia galvanised earth lead wire by means of bolts, nuts, check nuts and washers of galvanised standard iron or steel connected to main switch control board upto 7.5 Mtr away from earth electrode all as specified or indicated in electrical plate no 3 of MES Part-I, including testing on completion including the material and labour of the following :- (a) Excavation and earth work in any type of soil. (b) PCC 1:3:6 type C-1 in earth pit/chamber. (c) RCC cover slab of 50mm thick 1:2:4 with 8mm CTD 140mm C/C with suitable handle. (d) GI light grade pipe 20mm dia for watering pipe with funnel and GI light grade pipe 15mm dia for protection pipe., (e) Charcoal and salt. (f) Testing on completion. (g) Including taking out old unserviceable earthing with connected items. (h) Complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches, in any type of soil not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth; for foundation, etc. and getting out in any type of soil complete, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick each (soil), complete all as specified and directed.

Removing surplus excavated soil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete, all as specified and directed.

Dry sand cushioning to cable providing with a layer of sand 8cm deep before laying the cable and 15cm deep after laying and stretching the cable in trenches complete all as specified and directed by the Engineer-in-Charge.Note:- Punned thickness of sand shall be measured and paid.

Brick, old size 230X 115X 75 mm, well burnt sub class ’B’, laid dry with width equal to length of brick as mechanical protection to under ground cable complete all as specified and directed by the Engineer-in-Charge.

Cutting of PCC/Hard standing/WBM road not exceeding 20cm in width and not exceeding 30cm in depth for passing of LT cable and making good to disturbed surface to match with the existing specifications by using old and new material complete all as specified and directed.

Supply, laying and testing of XLPE insulated sheathed armored heavy duty LT 1100 Volts grade cable with aluminum conductors laid in trenches/pipe, fixed to poles, walls of size 10 sqmm 2 core, complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing GI tubing light grade 40mm dia along the wall/in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holding of GI pipe alongwith poles, complete all as specified and as directed by Engr-in-Charge.

MAHADEV ENTERPRISES

pargal builders

SARDALIA CONST CO

NARESH KUMAR KHAJURIA