PROVN OF RAISING OF LEVEL OF GANG CANAL PUMP HOUSE AT LGJ MIL STN

Amount

Demolition of RCC of any description and in any position not otherwise specifically provided and including removal of debriies from premises complete all as specified and directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, for soft soil complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar /cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Dismantling brick tiles or terracing tiles, single layer on roofs complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate in foundation, filling & mass concrete all as specified and directed.

M&L for brickwork with fly ash bricks, of old size bricks, straight or curved exc. 6 m mean radius built in CM (1:6) all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in soft soil complete all as specified

Excavating over areas, exc 1.5 m and n exc 3.00 m deep and getting out in soft soil complete all as specified

M & L for M-25 ( Design Mix ) reinforced cement concrete (20 mm graded stone aggregate), Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses , complete all as specified and directed

Formwork for fair finshed flat surface of concrete walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and directed.

M & L for M-25 ( Design Mix ) reinforced cement concrete (20 mm graded stone aggregate), slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Formwork to flat for fair surfaces of soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick complete all as specified and directed.

S&F for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

All as per item above here-in-before but 5 mm dia and over upto and including 10mm dia in stirrups, spacers and binders all as specified and directed.

M&L for rendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:6 on wall finished even and smooth without using extra cement all as sepecified and directed.

M&L for rendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth with all as sepecified and directed.

M&L for Roof treatment to RCC roof as follows:- (a) Cleaning the roof surfaces thoroughly using wire brusehes to remove sharp projections, cleaning joints, washing, drying and removing all dirt/dust to receive concrete padding/plaster etc. (b) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:4) with WPC, finished even and smooth without using extra cement. (c) Providing one coat of approved bituminous primer @100 gms per sqm, over dried plastered surface. (d) Laying 3 mm thick APP membrane,(mineral finish) reinforced with non woven polyster fabric, by torch application. The overlapping while torching shall be 75 mm on longitudinal direction and 100 mm on the transverse direction complete all as specified and directed by E-in-Charge. Make : STP Dr Fixit/Pidilite, Texsa India Ltd/Tikitar Dansona/Bengal Bitumen Notes : (i) All joints and change in directions should be covered wih cement mortar (1:3) mixed with SBR latex @ 200 ml/bag of cement/as per site reqmt and cured well before laying membrane by torching. (ii) All angles and abuttments should be sealed well with extra care to ensure full bondage. (iii) Water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only. The name of firm shall be got approved from GE before carrying out the wk. (iv) The independent testing of membrane for technical parameters given in particular specifications shall be carried out from Govt approved labs having fascilities for testing of membrane. (v) The guarnatee of treatment shall be for min 10 yrs reckoned from date of completion of whole wk.

M&L for rendering, 5 mm thick on brick work or concrete surfaces in cement mortar 1:3 on ceiling finished even and smooth without using extra cement all as sepecified and directed.

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces all as directed.

M&L for two coats of white wash on old plastered surfaces of ceiling including preparation of surfaces all as directed.

M&L for two coats of white wash on old surfaces of wall including preparation of surfaces all as directed.

Preparation of newly plastereD surface of wall and applying two coat of cement base paint over a coat primer over surface complete all as specified and directed.

Preparation of old surface of wall and applying two coat of cement base paint surface complete all as specified and directed.

M&L for two coats of acrylic distemper on newly plastered surfaces of walls paint over 3mm thick wall care putty including preparation of surfaces all as directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

M & L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conoforming to Fe 410 -W (Gde- E- 250) quality- A, complete all as specified and directed.

Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame)

S&F for 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as directed.

S&F for 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) all as directed.

S&F 100 mm long butt hinge, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 all as specidied and directed.

S&F 150 mm long aluminium anodised barrel tower bolt, of extruded sections all as directed.

S&F 150 mm long aluminium anodised handle, cast type all as directed.

S & F 300 mm, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F for 300mm ordinary rat tail rod pattern springs including roller and roller plate complete mild steel fixed complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer all as specified.

S & F in repairs Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

Ditto, as per ser item No 38 but without glazing bars

S & F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F for framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes, framed guard bars; barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 410-0 or Fe 165 complete all as specified and as directed

M & L for painting steel and iron surfaces of any description,over 10 cm width or girth, with preparation of new or previously untreated surfaces priming with one coat of read oxide & finish with two coats of synthetic enamel paint ordinary tint all as spefified and directed

Returning, filling in, including spreading levelling including watering & well ramming in layers n. exc 25 cm all complete as specified in soil.

Removing excavated materials .exc 250 m and depositing out of MOD land where directed at a level n.exc 1.5 m above the starting point all as directed.

M&L for hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc.15cm thick, watered and rammed to a true surface in Broken stone or boulders (15cm compacted thickness) complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-1 using 20 mm graded mechanically crushed stone aggregate as in PCCfinished even and smooth without using extra cement with & including 10 mm wide, 30 mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as directed.

M & L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bedding in cement mortar 1:6, all as specified and directed.

M & L Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and cement to match over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Taking down cement plaster/terrazoo on brick / stone walls including raking out joints, hacking for key, scrubbing down with water all as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises all as specified and as directed.

Taking down chowkhats or frames n exc 1.5 sq. m each with shutters (without taking off shutters from the frame)

M&L for joint free Glazed Ceramic coloured tiles of size 350 X 250 X 7 mm / 450 x 350 x 7 /600x600 x7 mm thick mm thick on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry and pointed in coloured cement to match the floor all as specified and directed.

S&F vitreous china squatting pan Orissa pattern size 580 x 440 mm white with integral foot rests (excl flushing cistern) but including CI 'P' trap set in and including concrete fixed complete all as specified and directed..

S&F PVC valve less, syphonic action type flushing cistern,10 ltrs capacity low level, white, with inlet ball valve, float, handle and telescopic pipe and connection to pipe and flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern all as directed.

S&F vitreous china wash hand basin coloured Flat back of size 550x400mm, long screwed shank fly nut flange end including cutting for and pinning in ends of brackets in 1:3 CM including 32mm dia chromium plated waste coupling/trap all as specified .

S&F pillar tap, fancy type, cast copper alloy chromium plated with capston head, screwed down high pressure with or without lettered with long screwed shank and fly nuts, screwed for iron pipe of 15 mm bore complete all as specified and directed. Wt not less than 450 gms

S&F bib tap 15mm bore cast copper alloy chromium plated long body fancy type with capston head and cup screwed down, hand operated, screwed for iron pipe or for brass ferrule all as specified.

S&F chromium plated brass stop/angle valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup fixed all as specified.

S&F CP brass stop valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup (Concealed type) fixed all as specified.

S&F shower rose, 125 mm size, brass chromium plated with sweivel joint all as directed.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm all as directed.

S&F for Rotational moulded polythene water storage tank 500 ltr capacity vertical with closed top hoisted and fixed in position all as specified in SSR part-I. All as directed.

S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore fixed in repair all as specified and as approved by GE/Engineer-in-Charge.

S&F ball PTMT valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe all as specified and directed.

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling complete all as directed.

All as per item above but 20mm dia pipe.

S&F 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors all as directed.

S & F 100 bore of spun cast iron soil, waste and vent pipes in any length with or without ears, with cement joint and laid in trenches or in floors cast iron complete all as specified and directed.

S & F 100 bore of spun cast iron soil, waste and vent pipes in any length with or without ears, with cement joint and fixed to wall and including clamps , out of 50mm by 5 mm flat and 16 mm dia round iron stays, complete all as specified and directed.

S & F 75mm bore of spun cast iron soil, waste and vent pipes in any length with or without ears, with cement joint and laid in trenches or in floors cast iron complete all as specified and directed.

S & F cast iron 100 mm bore Bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S & F cast iron 75 mm bore Bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S & F cast iron 100 mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S & F cast iron 100 mm bore cowl complete all as specified and directed.

M & L for 75 mm cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1, (1:2:4) complete all as specified and directed.

Surface excavation N.exc. (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base below floors all specified and directed.

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete.

M& L hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

M&L for Mild steel round bars 10mm dia and over, cut to length, bent to shape required, hooking ends, securing with chain link fencing all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provission of binding wire complete all as specified and directed.

Supply only Chain link MS galvanisd fencing, any size or type all as directed by Engr-in-Charge

M & L for bricks, sub class B, laid on edge in floors; old size bricks , laid dry and painted in CM 1:3CM

M & L Cement concrete type B- 1, 1:2:4 (20mm graded aggregate) 75 mm thick as in floor finsished even and smooth mixed with recron fibre or equivalent complete as per manufacturing instruction. (Recorn fibre measured separetely)

Supply only polyester triangular fibres as secondary reinforcement in all types of concrete and mortars (Make Reliance or equivalent)

Dismantling wrought iron or mild steel work of any description not otherwise provided for ( Including M S post) complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed

S & F galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

M/s Tarun Traders

AJAY CONSTRUCTION COMPANY

KHANNA CONSTRUCTIONS

Aggarwal brothers and company