ADDN / ALTN TO BLDGS AT SEWAR FORT BHARATPUR

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc Including all arrangments like scaffolding for working platform complete all as specified and directed .

M&L for Rendering 15 mm thick in CM (1:4) on fair face of brick work finished even & fair complete all as specified and directed .

All as above item no 2 but in CM (1:6) but on other than fair face of brickwork complete all as specified and directed.

M&L cement plaster for dubbiing out average 10 mm thick in CM (1:6) on irregular face of walls complete all as specified and directed.

M&L for preparation of New plastered surfaces and applying two coats of exterior emulsion paint (weather proof anti algae) 100% acrylic emulsion paint over a coat of EXTERIOR WALL PRIMER complete all as specified and directed.

M & L Preparation of new plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of distemper oil emulsion white or tinted over a coat of wall primer wash with hand roller over 1.5 mm wall care putty complete all as specified and directed.

M&L for completely removal of existing treatment of old plastered surfaces and aapplying two coats of exterior emulsion paint (weather proof anti algae) 100% acrylic emulsion paint over a coat of EXTERIOR WALL PRIMER complete all as specified and directed.

M&L for two coats of Oil bound distemper on old surfaces , after completly removing existing treatment by using steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots removing nails and filling small holes by putty and rubbing surface by sand paper to prepare the surface andwalls, white or tinted including complete removal of existing treatment over a coat of 1.5 mm thick wall care putty complete all as specified and directed.

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of white wash complete all as specified and directed.

M&L for two coats of white wash on old plastered or unplastered surfaces of Ceiling including Complete removal of existing treatment complete all as specified and directed.

M & L Preparation of old decorated plastered or undecorated plastered surface of wall including cornices, pilasters etc by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

M&L Preparation of newly plastered surfaces of wall & applying three coats of white wash complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoin jambs pillars etc. complete all as specified and directed.

M&L Brick work with sub class 'B' old size bricks bricks straight or cured on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for surface excavation n.exc. 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

M&L for broken stone or boulders in hardcore of gauge exc 63 mm but n.exc 100 mm deposited spread and levelled in layers n. exc 15 cm thick watered and rolled/rammed to a true surface complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2 using 40mm graded aggregateas in sub base ,sub floors, floors & pavings complete all as specified and directed.

M&L 75 mm thick PCC 1:4:8 type D-2 using 40mm graded aggregate as in sub-base, sub- floors, floors & pavings complete all as specified and directed.

M&L Sand cusion under floor ,spreading and levelling in layers 25 mm thick complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade With Grey Cement and pigment complete all as specified and directed.

M&L for 30-35 mm. thick Dholpur slab in floor set in 20 mm thick (avg.) cement mortar (1:4) bed and pointing with cement mortar (1:2) (cement 1, stone dust 2) with admixture of pigment matching the stone shades, polished finished dressed complete all as specified and directed.

Dismantling of stone slab and tiles of any description or thickness in floors, etc. laid dry & in pointed complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 CM thickness (below or above GL) complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over cement screed 20 mm thick in cement mortar 1:6, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dedo and pillar laid over cement screed 15 mm thick in cement mortar 1:4, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Taking down chowkats or frames n. exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutter of any description area exc 1 sqm and n. exe 2 sqm complete all as specified and directed.

Taking down shutter & Resecuring or easing & adjusting shutters of any description exc 1 sqm and n. exc. 2 Sqm each. & refixing in other opening complete all as specified and directed.

M&L for Factory made steel window with side hung shutteers including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and directed. Note :- Mild steel wire cloth shall be measured and paid separately under respective items.

All as per item No 30 above but without glazing bars.

S&F 35 mm thick 2nd class hardwood ( hollock ) factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in SSR Part-I complete all as specified and directed.

S&F 35 mm thick 2nd class hardwood( hollock ) factory made plain framed, panelled shutters (any No. of panels) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces size of members as per IS 1003 PtI complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges,steel peg stay, handle complete all as specified and directed.

S&F for sollid PVC door frame of size 50mmx47mm made out of 5mm plain colour pvc sheeet reinforced with m.s. squre tube complete all as specified and directed.

Supplying & fixing in the frames at site factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified and shown on serial pages No. 142, 143, 144 , 145 & 146 of SSR 2020 (Part-II) and Particular specification complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, door chowkats of angle or other section and similar works complete of Gde Fe-290 Gde E-165 including welding etc. complete all as specified and directed.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position complete all as specified and directed.

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified and directed.

S&F 150 mm long mild steel barrel tower bolts stove enameled black with bright bolt (ISI marked) complete all as specified and directed.

S&F Mild steel presses steel bow handle oval type stove enameled black of size 150 mm (ISI marked) complete all as specified and directed.

S&F MS sliding door bolt, plate type, 300mm long, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed complete all as specified and directed.

S&F extruded aluminium alloy handle 150mm size fabricated type anodised, ISI marked complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt 150mm long of extruded section and fixed complete all as specified and directed.

S&F 75 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

M&L for Sheet glass ordinary quality 3 mm thick and glazing with oil putty in square n. exc 0.50 sqm in each pane complete all as specified and directed.

Hacking out old broken glass any thickness, size, quality or description from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads including S&F 3 mm thick plain sheet glass ordinary quality in square not exceeding 0.5 complete all as specified and directed.

All as per item No 48 above but supply and fix in repairs.

Painting to new or previously untreated steel surfaces of any description over 10 cm in width or girth with two coats of synthetic enamel paint over a coat of Zinc chrome primer including preparation of surfaces complete all as specified and directed.

M&L for preparation of new or old untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for one coats painting with synthetic enamel paint to old wood or wood based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface including all preparatory work complete all as specified and directed.

M&L for one coats painting with synthetic enamel paint to old steel or steel based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface including all preparatory work complete all as specified and directed.

Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as specified & as directed (also including the rate for disposal of building rubbish/ malba of dismantled or waste material collected after demolition of existing treatment & dumping for lead upto 1km for all lifts) complete all as specified and directed.

M&L for 40mm thick pcc type -B-1 (1:2:4) using 20mm graded stone aggregate in roof covering , benching , etc & finished even and rough without using extra cement complete all as specified and directed.

M&L for screed bed or bedding layer of 15 mm thick cement mortar 1:4, for floor finished even & smooth without using extra cement (mixed with WPC & paid seprately) complete all as specified and directed.

Supply only water proofing compound ISI marked complete all as specified and directed.

M&L Non - skid Endura Cool Roof SRI colored tiles 10 mm thick area of each tile 300X300, in floors etc over 15 mm thick screed bed in CM 1:4 (mixed with WPC & paid seprately) in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.

M&L APP based polymeric membrane not less than 3mm thick , weighing not less than 3.5 Kg / sqm , and upper side of membrane thermally insulated with white mineral gravel finish , informly embedded during manufacturing process,shall only be used . It shall be laid by torch application .Side over laps shall be 75 mm and the end shall be 100 mm and all overlaps and joints shall be sealed by torch application including applying a coat of cold applied bitumen primer conferming IS:3384 @0.40 Kg/Sqm & applied a hot blown coat of bitumin layer spread over primer @ 1.2 Kg/Sqm complete all as specified and directed.

Cutting holes exc 150 sqcm but n.exc 400 sq cm into or through brick walls, in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime concrete and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

S & F Fe 410-W (Gde E-250)) quality B rolled mild steel in Joist channel, angle or tee,I sections, fixed independently, without connecting plates etc (cut to ordinary lengths i.e, within 20mm of the length indicated) complete all as specified and directed.

Dismantling stone slabs in roofs, suspended floors, chajjas, landings,sides of pillars etc., any thickness, jointed in any mortar & remove it carefully complete all as specified and directed.

M&L for sand stone slabs 10-15 cm thick in ,roof ,sun shades, shelves, cills, landings, cover stones, templates, fix to pillars etc. in any length, punched dressed on face and along exposed edges, self faced on other side and set in Cement mortar 1:2 complete all as specified and directed.

M&L dismantling floor,heart or wall tiling including cement mortar bed(but not backing) , removing serviceable tiles to store and rubbish off the premises complete all as specified and directed .

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 350mm x 250mm, 7mm/450X350X7mm thick over and including 15 mm thick rendering in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Non - skid Ceramic colored tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc over 15 mm thick screed bed in CM 1:6 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.

M&L for Coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm bur not exceeding .11 sqmm, over 15 mm thick screed bed in CM 1:6 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match for repair & matched to existing floor tiles in patches complete all as specified and directed.

M & L for Endura Designer Collection Series of Jhonson Tiles ,Kajaria or somani tile of size 400x400x10 mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 15mm thick base of cement mortar 1:4 in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete all as specified and directed.

Providing and fixing 20 mm thick gang saw cut, mirror polished, premoulded and prepolished,Granite of any colour and shade machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. rubbing, cutting, moulding and polishing to edges to give high gloss finish etc. complete all as specified and directed.

M&L or Cutting, polishing existing Kota/ marble floor ,red stone flooring,or at verticle surfaces (three cuttings and mirror polishing) including Manson polishing, levelling certain places to Kota/ marble floor ,red stone floor ,necessary repair work & all necessary arrangments complete all as specified and directed.

Supply and fixing anodized snap grid frame work of size 605mm x 605 mm for false ceiling including necessary notching. The snap grid shall consist of anodized aluminium main & cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/RM and 23.5 x 26.4 x 1.40 mm weighing 0.191 Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminum angle bracket of size 15mm x 15mm x 1.5 mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washer. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminum angle of size 40 x 25 x 2 mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and providing 10 mm thick mineral fibre board of make Armstrong in fixed in grid support with 6.0 mm dia plain mild steel wire galvanised class 3 fixed in detached works etc to support snap grid, made of aluminum as per specification complete all as specified and directed.

Dismantling of Stone Jali & Stone Pillar of any description , any thickness complete all as specified and directed.

M&L for 40 mm thick Sikandra stone jali decorative design of approved pattern by Eng-in-charge including all carving and moulding of corners fixed in cement mortar 1:4 to grooves of stone pillars application with colouring to match with colour of jali including fixing of stone jali for all corners & lift complete all as specified and directed.

S&F stone pillars(post) of size 100x100 mm including engraving decorative design of approved pattern on two face and dome shape approved by GE , height of each post as per sikandra jali, ,making groove on two face of size 43x5 mm for fixing of sikandra Jali in CM 1:4 complete all as specified and directed.

Repair of existing sandstone chajja (of approved quality) (As per existing size length x width 600 to 750 and thikness 40-50 mm) by replacing damaged/ missing stone chajja, wherever required as per old existing design, including cost of dismantling/ making of wall/ parapet where chajja is inserted/fixed . Item includes cost of safety measures/ use of specified equipments for workers of building required to complete the work at all heights & including all leads complete all as specified and directed.

Cleaning and polishing existing finials over chatri /Balcony/Jhorakha using with light dry dusting and removal of surface crusts , bubbling , loose/ flaking paint using careful sand papering with fine wet and dry carborundum paper and wiping clean with proper care as per prescribed process and specification Item also includes cost of shuttering /scaffolding /safety measure /use of specified equipment for workers of building required to complete the work complete all as specified and directed.

Repair ,Cleaning and fixing of hanging decorative stone brackets as per old design including patch repair( if any ) and chemical wash( amonia or as approved) with complete materials and specification .Item also includes cost of shuttering /scaffolding /safety measure /use of specified equipment for workers of building required to complete the work complete all as specified and directed.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil complete all as specified and directed.

M&L Cement concrete in foundations filling and mass concrete Type C-2 1:3:6( 40 mm graded aggregates ) complete all as specified and directed.

S&F rolled mild steel work as in post ,roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections,ms pipe) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A' complete all as specified and directed.

M & L for Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F for in repair Brass Chromium plated long body Bib cock with wall flange complete all as specified and directed.

S&F for in repair Brass Chromium plated Health faucet (ABS body) with 1.2 m long PVC tube covered SS covered and wall flange complete all as specified and directed. Make : Cat Part No - ESSCO Cat Part No. : ALE E55-583 or equivalent Hindware, Cera, Prayag, JOHNSON, Jaquar

S&F for in repair Brass Chromium plated Angular stop cock with wall flange complete all as specified and directed. Make : Cat Part No - ESSCO Cat Part No. : APR 101053 or equivalent Hindware, Cera, Prayag, JOHNSON, Jaquar

S&F viterous china Table top Art basin with CP waste coupling , 610mm x 375mm x 115 mm complete all as specified and directed. Make : Cat Part No - Kerovit Catolouge MYRA KB284 or equivalent Hindware, Cera, Prayag, JOHNSON, Jaquar

Providing and fixing in white vitreous china Large ISI Urinal SIze of 385X325X635mm and sizes respectively with with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete all as specified and directed. Make : Cat Part No - Jaquar Catolouge No. : URS-WHT-13253N or equivalent Hindware, Cera, Prayag, JOHNSON

S&F for in repair Brass Chromium plated central hole basin mixer with extension body & fixed spout complete all as specified and directed Make : Cat Part No - Jaquar Catolouge No. : C0P-021PM or equivalent Hindware, Cera, Prayag, JOHNSON

S&F in repair stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed of following size in repairs a. 20mm Dia complete all as specified and directed.

M&L for PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed

S&F for in repair Brass Chromium plated Towel rail 600mm long complete all as specified and directed.

M&L in repair PVC floor trap of 75mm bore, with grating Jali including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

M&L in repair Soap dish Holder , fixed to plugs with chromium plated brass screws complete all as specified and directed. Make : Cat Part No - Jaquar Catolouge No. : CAN-1131N or equivalent Hindware, Cera, Prayag, JOHNSON

S&F Toilet paper holder of stainless teel with flap, box type fixed to wall with chromium plated (CP) brass screws complete all as specified and directed.

S&F for Brass Chromium plated Towel rack 600mm long with lower hangers complete all as specified and directed.

Dismantling and taking up or down the existing unserviceable GI pipe and M&L for new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors of following sizes :- (a)15 mm bore

(b)20 mm bore

Taking up or down old serviceable GI pipe & Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, trenches etc ) including cleaning of following sizes:- (a)15 mm bore

(b) 20 mm bore

Dismantling of old existing unserviceable WHB glazed and S&F new vitreous china wash hand basin, white, of size 550x400mm flat back excluding taps, waste, chain and plug but including brackets, full pedestal cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F in repair waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including 32mm PVC waste pipe for WHB complete all as specified and directed.

S&F in repair Sink made of stainless steel 1 mm thick Kitchen or Laboratory with plugs, washers and wastes; including beding in cement mortar on to dwarf walls or including fixing cantilever brackets and connecting union to waste pipe overall size 495mm x 420mm bowl size 410mm x 330 mmx160mm complete all as specified and directed.

S&F in repair of brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union including taking down of old shower rose of any size, any type complete all as specified and directed.

S&F in repair of PVC low level flushing cistern 10 ltrs capacity with inlet ball valve float & handle, syphonic action type including brackets & flush pipe of polythelene of low or high density or PVC 32mm dia for LLFC fixed complete all as specified and directed.

S&F in repair of PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, ISI marked of 75mm bore complete all as specified and directed.

S&Fin repair of PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked of 110mm bore complete all as specified and directed.

S&Fin repair of PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, ISI marked of 110mm bore complete all as specified and directed.

S&F in repair Single piece-WC with UF Soft Close Slim Seat Cover, Fixing Accessories, Accessories set and Cistern Fittings, Size: 370x670x720 mm, S Trap-220mm complete all as specified and directed. Make : Cat Part No - Jaquar registered design LYS-WHT-38851S220UFSMN or equivalent Hindware, Cera, Prayag, JOHNSON

S&F in repair vitreous china squatting pan (Orissa pattern) water closet (white) size 580mmx440mm with integral foot rests (excluding flushing cistern and flush pipe) complete including connection to trap and flushing pipe antisyphonage pipe etc including provision of PCC (1:7:12) type F2 in filling complete all as specified and directed.

Dismantling corrugated or semi corrugated Asbestos cement sheets in roof coverings complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description & fixed in any position, complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels cantilevers, shelves including supports, overhungs etc. also splays between floors and beams etc. as in rough finished surfaces complete all as specified and directed.

M&L for Reinforcement concrete M-25 (20 mm graded aggregates) as in beams, cantileveres, bressummers, lintels over 1.5 m span complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar works not exceeding 200 mm thick (Horizontal or slopping) complete all as specified and directed.

M&L for Reinforced cement concrete (Design Mix M-25) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F mild steel TMT bars 06 to 08 mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in strips, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for Rendering 5 mm thick in cement and sand mortar 1:3 on fair faces of cement concrete surfaces of ceiling of chajjas/roof protection etc including finishing the surface even and smooth without using extra cement complete all as specified and directed.

S & F powder coted Anodised Aluminium frame for door,windows,vantilators,partion wall with one or more rebates including joining cleats for fixing etc complete all as specified and directed.

S & F powder coated Aluminium door shutter,aluminium section weighing 0.55kg/m including necessary joining cleats zlazing clips,rubber neoprene packing handles 2 Nos in each door,hinges anodized aluminium snap beading screw etccomplete all as specified and directed.

S&F powder coated Anodised aluminium window and ventilators shutters,side hung type without sash bars,aluminium section weighting 0.55 kg/m including necessary joining cleats,glazing clips,rubber packng,anodised aluminium snap beading, screws, anodised aluminium fitting such as peg stays 150mm long 1 nos ,hinges type B-21 100 mm long Nos suitable handle Nos complete all as specified and directed.

S&F in repair aluminium extruded section body door closer hydranlicelly regulated designation no 3 universal type suitable for door shutter up to 851 to 1000 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

S&F Sheet glass 5.50mm thick ordinary quility and glazing with oil putty in square n.exc 0.50 sqm in each pane complete all as specified and directed.

All as per Item No 124 above but exc 0.5Sqm in each pane

M&L for providing and fixing 4mm thick Aluminium Composite Panel (ACP) Sheet for partion,door of approved make,color & shade.Joint of sheet to be finished with selecon based sealent also including all fittings & fixtures complete all as specified and as directed

S&F toughened glass of approved make and brand of 10mm thick coloured/ tinted/ smoke / clear glass confirming to IS-2563(Part-I) 1990 for partition using glazing clips,cleats and special metal sash putty alongwith all fixings and fixtures complete all as specified and directed.

Providing and fixing in 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, complete all as specified and as directed . Note:- Door handle, lock and stopper etc.not to be paid separately.

Dismantling 500 ltr water tank and M&L new 500 ltr ISI marked three layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position & including 20mm brass ball valve complete all as specified and directed.

M&L of Cast iron floor trap of 100mm bore, with grating Jali including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F in repair pillar tap, cast copper alloy with capstan heads, chromium plated,fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified and directed.

Razing off/ taking down old existing unserviceable cement plaster, loose / unsound weaken cement concrete of any description and in any position from existing external / internal surfaces of RCC roof / slab / beams / columns / RCC facias, or any surface average depth 25mm (Approx height 15.0 m from natural ground level) with power driven of pneumatic chisel and and removal up to the approval municipal dumping grounds specified by the local bodies outside MOD land including cutting of all edges, making square shoulders of the cavities, roughening the smooth surfaces, scrapping out / removing corrosion all loose / scale / rust etc from the visible unplastered surface and applying one coat of styrene butydiene polymerized cement mortar Modifier TM-BOND® SBR or AR for bonding with cementious mortar specially adhered to BS 6319 having specific gravity of 1.025 to 1.04, minimum 43% solid contents) not less than 2% by weight of cement and as per manufacturer,s instructions Make of -Thermax/chemco system/webac chemicals. for B/P the surface before application of rheoplastic cementious based repair conforming to BS 6319. Ensuring no porosity in new surface.Complete all as specified and directed. Note—this item shall be undertaken by the authorized rep of manufacturer.

M&L for drilling hole in RCC/Bricks structures using drilling machine up to a depth of 50 mm and 15 mm dia, with the gap of 600mm removing dust, etc by vacuum cleaner and blowers, providing and fixing of heavy grade GI pipe nipple 15 mm dia, 50 mm long, @ 1.0 mtr c/c in both direction and injection cement slurry mixed with liquid integral waterproofing additive WAREP 1000L for concrete conforming to EN 934-2 T9 confirms to IS 2645-2003. Make of -Thermax/chemco system/webac chemicals. having specific gravity 1.1-1.2 gms/cc, chloride content: Nil as per IS 2645-2003 in combination with expanding powered or dual shrinkage compensating non shrink free flow plasticized grouts conforming to the requirements of BS EN 1504-3 class R4. and directed by GE.Complete all as specified and directed. Note—this item shall be undertaken by the authorized rep of manufacturer.

M&L for providing 25 mm thick one COMPONENT BS 5F chloride free thixotropic fibre reinforced polymer modified repair mortar 5F complies with ASTM C 109 with flexural strength ASTM C 348 @ 7 days meeting 7N/mm2 and tensile strength @ 7 days (ASTM C 307) >3 N/mm2 at the outer or inner Brick or stone walls in cement mortar in the ratio 1:4 mixed with for external or internal surface of RCC /slab /beam /columns/facias/any brick or stone wall surface etc. Make of -Thermax/chemco system/webac chemicals top surfaces of the plaster shall be finished even and smooth with using extra cement etc complete all as specified and as directed. Note—this item shall be undertaken by the authorized rep of manufacturer.

M&L for providing and applying Rheoplastic non shrink, corrosion resistant, High strength compound BS 66 MuCis on external or internal surface of RCC roof/floors/ceilings/chhazas /slab/balconies /beam /columns/facias/any brick or stone iner or outer wall surface etc, BS 66 having compressive strength as Bs 4551-80 thickness of40- 50mm with 1:4 cement mortar and strength (ASTM C 109)-80 Mpa @ 28 days, Tensile strength 2.0N/mm2 @ 28 days (ASTM C 348)- 4 Mpa @ 28 days, Flextural strength 10N/mm2 (ASTM C 348)-11 Mpa @ 28 days, Young's modulus -27 KN/sqmm (ASTM D469), Expansion charactristics (ASTM C 827-1987) Unrestrained expansion upto 4% pressure to restrain plastic Expansion -Approx. 0.004 N/sqmm make of- thermax/chemco system/webac chemicals., before pouring micro concrete it is recommended to apply granolithic E-Resin based solvent free concrete bonding agent/EP in accurate proportion with complete homogenesity. make of Thermax / Chemco system / Webac Chemicals having mix density of 1.45 to 1.5 kg/litre, Compressive strength (BS 6319 pt.2)-40 Mpa at 7 days, Flextural strength (BS 6319 pt.3)- 25 Mpa at 7 days, Tensile strength (BS 6319 pt.7)- 15 Mpa at 7 days, Bond strength (ASTM C 881)- 11 N/sqmm at 7 days, having an over lay time of 03 hrs at 30 C. pouring of micro concrete into the formwork using suitable arrangement or required using pumping device for uniform flow of micro concrete. The side shuttering can be removed after 3 days, and the bottom shuttering after 7 days, ensuring proper bond between the micro concrete and existing surface etc. complete including all tools and tackles as directed by Engr-in-Charge. Note: - Rate quoted shall include for necessary formwork required in the item. Note—this item shall be undertaken by the authorized rep of manufacturer.

M&L for providing and fixing welded MS wire mesh weighing not less than 1.5 kg/sqm and applying - Mucis protezioz ferro mono primer (single component cementitous corrosion inhibiting primer) of make Thermax Ltd or equivalent of webac chemicals /chemco system on exposed wire mesh having Mixed density of 2.01 to 2.05 Adhesive bond strength - 1N/mm2 touch drying time of 10-15 minutes at 35 degree celcius and recoable time 30 minutes and applying 25 mm thick COMPONENT BS 5F chloride free thixotropic fibre reinforced polymer modified with guniting machine/shotgun pressure not less than 5kg per sqr in the ratio of 1:4 mixed with liquied water proofing admixture (warep of make Thermax Ltd or equivalent & all further all specification as per item No 03 complete all as specified and directed.

M &L for curing of the surface using Maxcure CC 75 curing efficiency; Make of -Thermax/chemco system/webac chemicals. Maxcure CC 75 complies with the internationally recognized ASTM C309-90 standards incuding all tools and tackles complete all as specified and directed. Note—this item shall be undertaken by the authorized rep of manufacturer.

M&L Cement concrete in foundations filling and mass concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregates complete all as specified and directed.

M&L Providing PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in coping,bed plate including weathering slightly rounded or chamfered angles and throating etc complete all as specified and directed.

M&Lrendering 15mm thick on stone other than fair faces of brick surfaces in CM 1:4 surface finished even and smooth w/o extra cement complete all as specified and directed.

M&L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 with integral water proofing compound @ 3% of cement finished even and smooth without using extra cement complete all as specified and directed.

Supplying only integral water proofing compound complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting ou in soft/loose soil complete all as specified and directed.

Excavating in trenches, n. exc 1.5m wide and exceeding 1.5 m but n.exceeding 3m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and and getting outin soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25 cm soft / loose soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar150mm complete all as specified and directed.

M&L for 150 mm bore reinforced cement concrete pipe , class NP-2 laid & jointed complete with collars in cm(1:1) with spun yarn & tested . Complete all as specified & directed.

M&L for Plain cement concrete 1:4:8 type D2 (Using 40mm graded crushed stone aggregates) as in bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150mm bore complete all as specified and directed.

Providing precast cement concrete in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain with plain fair faces, including chamfers weatherings throating etc. and setting in mortar complete with joints to match, type B-1, 1:2:4 using 20mm graded crushed stone aggregate Set in CM1: 4 complete all as specified and directed.

Cutting in to existing manhole for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required (150 mm) bore complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 using 20mm graded crushed stone agg as in channel/benching in man hole etc,finished even and smooth using extra cement incl necessary form work complete all as specified and directed.

Construction of septic tank for 50 users complete all as specified and shown on drawing No. CEJZ/2002/TD/S-2(1/1).

Construction of soakage well 2.4 mtr dia and 3.00 mtr deep complete al las specified and shown on drawing No. CEJZ/2004/TD/S-35(1/1).

Taking up or down GI tubing and connections of the following sizes from trenches / wall / floor including cleaning for refixing or removal and deposit to MES strore yard complete all as specified and as directed of following sizes:- (a) 50mm bore

(b) 25/20mm bore

Supply & laying GI pipe medium grade with all fittings laid in trenches in old/new position as directed of following sizes: Note: Item rate to be quoted include the rate of connection to main DI pipe line. (a) 50mm bore

(b) 25mm bore

(c) 20mm bore

Taking out the unseviseable CI/DI pipe lines including all fittings with spigot and socket ends and lead joints including burning out joints and recovering lead and cleaning the pipes internal/external for reuse 100 mm dia bore of pipes complete all as specified and directed.

Supplying, Laying, jointing, testing and commmisioning of DI Pipe 100 mm bore,K-7 as per IS 8329, class K-9/ K-7 with inside cement mortar lining with spigot and socket ends laid in trenches complete all as specified and directed. Note : - Joints shall be measured and paid separetely

Bends tapers any type, (straight, bend, increasing, decreasing or double socket etc). Tee pieces single branch "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs of CI fittings upto 150 bore complete all as specified and directed.

construction of brick masonry vavle pit of internal dimension 90cmx90cmx90cm depth with sub class "B' bricks in cm (1:4) and 10 mm thick plastering in CM(1:4),PCC (1:4:8) type D2 (Using 40mm grade broken stone aggregate) as in foundation lean concrete PCC (1:3:6) type CI (Using 20mm grade broken stone aggregate ) as in bedding and copping MS frame with 40x40x6mm angle iron 3 mm thick MS sheet cover plate with locking arrangement, hinges and two coats of sythetic enamel paint over one coat of red oxide primer including preparation of surface three coats of white wash on plaster surface (exposed to view) including necessary excavation in soft loose soil returning filling in and removal of surplus soil to a distance not exceeding 50 m complete all as specified and directed.

Supplying & fixing gun metal gate valves with iron wheel head, screwed both ends for iron pipe, ISI Marked, as per IS: 778 of followng sizes:- (a) 50mm bore

(b) 25mm bore

(c) 20mm bore

M/L for taking out Unsv U/G cable PVC insulated armoured PVC sheathed Al Conductor, LT cable of any size complete all as specified and directed.

S&L pipe galvanised medium class complete including fittings 15mm dia complete all as specified and directed.

Supply, laying, testing & commissioning LT XLPE cable insulated armoured (heavy duty) electric cable with stranded aluminium conductor 1100 volts grade (ISI marked) & laid in trenches/pipes or fixed on pole complete all as specified and directed of followng sizes:- (a) 70 Sqmm 3.5 core

(b) 25 Sqmm 4 core

(c) 10 Sqmm 2 core

Supply & spread unwashed dry river sand for sand cushioning and covering the under ground cable in trenches complete all as specified and directed Note :- Punning thickness shall be measured.)

M&L for brick protection with sub Class`B` bricks old size laid dry, flat over cable perpendicular across the cable in trenches complete all as specified and directed.

Out going:- (a) MCB TPN 40 Amp,'C' curve ,10kA rapturing capacity-02 Nos (b) MCB SP 6 Amp,'C' curve ,10kA rapturing capacity-12 Nos (c) MCB SPN 40 Amp ,'C' curve, 10kA -10 Nos

Taking down carefully copper/aluminium point wiring (light, fan, bell,socket or power) complete fittings such as switches, ceiling roses, pendents, holders,regulators, sockets etc removing materials for taking credit and making good disturbed surfaces of wall, floor & ceiling etc.

Dismantling of old U/S rusted main switch/DB of any size capacity and make.

M&L point wiring complete with 1.5 Sqmm 02 x single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in rigid PVC conduit pipe size not less than 20mm dia with all PVC accessories such as Tee, bend, collar, elbow, square junction box etc fixed on the concealed surface of wall/ceiling by means of PVCsleevel/dash fastners with cadmium plated screws including suitable size SS / MS shunken/metal flush box for mounting of flush type/modular fittings like switches, sockets, fan regulator etc including 1.5 Sqmm PVC insulated but unsheathed copper earth continuity conductor (in green color) to common earth and connedcted to earth dolly complete all as specified and directed for the following :-

(a) One light point controlled by one way switch.

(b) One ceiling fan/wall fan/exhaust fan point controlled by one way switch.

(d) One 3 pin 6 Amp socket point outlet on the same board with other switches

(e) One 3 pin 6 Amp socket point outlet on the independent board

All as per item No. 177 above but with multi stranded copper conductor cable 2.5 Sqmm size for 3 pin 16 Amps switch socket outlet on independent board including 2.5 Sqmm copper cable PVC insulated FRLS unsheathed copper continuous earth wire including connecting to common earth dolly.

S&F ceiling rose surface bakelite 50 x 40 mm three terminal ISI marked including suitable size of PVC board complete all as specified and directed.

S & F Lamp holder, PVC/polycarbonate type with cord grip cap suitable for pendant fitings complete all as specified and directed.

S & F stepped type electronic fan regulator flush type 230 volt, 100 watt on the existing phenolic laminated sheet etc. complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 Amps multi purpose flush type 230 volt complete all as specified and directed.

S&F switch piano flush button single pole one way 6 Amps 230 volt grade complete all as specified and directed.

S&F switch socket combination 2 in 1, 5 A flush type complete all as specified and directed.

S&F switch socket combination 3 pin 16A, flush type complete all as specified and directed.

M&L in repair submain wiring complete with 2X 6 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor and one run of 6 Sqmm copper cable for earth continuity conductor and including rigid PVC conduit with all PVC accessories fixed on concealed surface complete all as specified and directed. Note: Two runs 6 Sq mm , one run of 6 Sq mm earth wire & One run of PVC conduit will measured as one RM.

M&L in repair submain wiring complete with 2X 4 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor and one run of 4 Sqmm copper cable for earth continuity conductor and including rigid PVC conduit with all PVC accessories fixed on concealed surface complete all as specified and directed. Note: Two runs 4 Sq mm, one run of 4 Sq mm earth wire & One run of PVC conduit will measured as one RM.

Distribution board factory made and tested made of sheet metal enclosure powder coated suitable for mounting the MCB 240 volt of the following DBs:-

(a) 4 way TPN with 200 amps rated busbar 415 volts (double door type).

(b) 8 way SPN with 200 amps rated busbar 240 volts (double door type).

S&F MCCB/MCB 415/240 volts fixed in DB's of the under mentioned type and rating:- Note: Make of MCCB/MCB should be same of DB.

(a) MCB TPN 63 Amps 415 volt, Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

(b) MCB SP 6-32 Amps, 240 volts,Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

(c) MCB SPN 40 Amps, 240 volt,Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

Taking out existing LED tube light light and fixing after repair work complete necessary fixing arrangements on wall complete all as specified and directed.

Supply and fixing LED 20 watt LED tubelight fitting retro fit type with replacable rod complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, complete all as specified and directed.

Taking out LED bldg security light incl GI bracket and fixing after repair work including nuts bolts & washers complete necessary fixing arrangements on wall/ pole complete all as specified and directed.

Taking out exhaust/ceiling fan and fixing after repair work at existing/where required incl minor repair incl greasing/oiling, capacitor replacement, paiting, service wire from fan to ceiling rose ,MES No writing on fan complete all as specified and directed.

M&L bracket light fitting wall mounting, champagne gold finish fixture with plastic body suitable for 9 W LED lamp B22 base complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

Supply and fixing of Electric storage water heater of 25 liter capacity whirl flow technology 2000W rated power 5 star rating, energy saving, high density PUF insulation 8 Bar pressure, heating indicator, adjustable knob for mannual setting of temp, safety valve, vertical mounting including wall mounting fastner bolts 04 Nos and 02 flexi connecting pipe of length upto 60cm PRCD plug (shock safe) complete all as specified and directed.

Supply, fixing and fabrication and testing desert cooler in GI body sheet with and including exhaust fan size/sweep 450 mm (fan blade only) 230 Volts, Single phase 50 Hz, 1400 RPM, heavy duty single sheet, totally enclosed. The overall dimesnions of the desert cooler shall not be less than 820mmx690mm x 1120mm with and including following accessories each:- (a) Air grill of suitable size made out of 0.5 mm PGI sheet including GSS arrangement with a knob for easy and smooth movement. (b) Front panel made out of 0.60mm thick PGI sheet of suitable size and shape. (c) Water tank of capacity not less than 120 Litres. (d) Submersible pump electric driven single phase 230 volts, 50 Hz of suitable discharge and head but motor capacity not less than 40 watt. Make : Khaitan/Crompton or equivalent make. (e) Service cord of 3 Core copper wire 1.5 Sqmm with plug top 5 Amp length not less than 2 metres. (f) Electronic fan dimmer 1000 watts AC 230 Volt, 2 module for controlling the fan speed. (g) Complete electric wiring of desert coolers as required to operate fan and pump along with 5 Amp switches . (h) Exhaust fan shall be mounted on wooden frame duly fixed with cooler body. (j) Make of exhaust fan. Havells/Crompton Greaves/Marathon/Almonard. (k) Make of PGI sheet. Tata/Jindal/National.

M&L for making desert cooler stand made out of 40X40X5mm ISA angle iron work of required size complete paint with two coats of synthetic enamelled paint over a coat of zinc chrome primer complete all as specified and directed.

M & L earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washer etc of galvanised iron and earth lead protected by provision of GI pipe light grade 15 mm bore from earth elelctrode to test point incl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone agagregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM sheet (weight not less than 4Kg/Sqm) and frame of angle iron 25 x 25 x 6mm with lugs 2 Nos and with 8mm dia MS bar handle made to shape, GI pipe medium grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling test point with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr, complete all as specified in electrical plate No 3 of SSR Part I and connection to earth test point including testing on completion all as specified and directed. Note :- The cost of funnel pipe of 20 mm GI light grade pipe and protection pipe of 15mm bore GI light grade is deemed to be included in quoted unit rate.

M/S MAKHIJA TRADERS (BID ID -3170926)

SUNAR CONTRACTOR (BID ID -3170971)