ADDN ALTN TO GROUND FLOOR AND BLDG NO P5 AT OTM COMPLEX DHQ7 PARADIP AND PROVISION OF FALSE CEILING AND PAINT REPLACING OF LED LIGHT OFFICERS LOUNGE PROVISION OF VITRIFIED TILES IN CERTAIN OFFICES AND REPLACEMENT OF TILES AT CERTAIN PLACES PROVN OF W

Amount

B/R PORTION Taking down wooden frame with shutter without taken off shutter from the frame,exceeding 1.5 sqm but not exceeding 4 sqm each including removing from site complete all as specified and directed.

Taking down wooden frame with shutter without taken off shutter from the frame,not exceeding 1.5 sqm each including removing from site complete all as specified and directed.

S&F 2nd class hard wood plain solid straight chowkhat and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joint complete all as specified and directed.

Supply and fixing of 2nd class hardwood 40 mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

S&F 150 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F 100 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F 150mm long Extruded aluminium alloy handles, fabricated type,anodised complete all as specified and directed.

S&F mild steel sliding door bolts,300 mm long plate type, of brass stove enamelled black with bright bolt not less than 12 mm dia with and including minimum of 6 bolts and nuts,four on bolt plate and two on staple and fixed complete all as specified and directed.

S&F 140mm long Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F mild steel flat iron as in hold fast clamps articles conforming to Fe-290 gde E-165 complete all as specified and directed.

S&F 100mm long MS Butt hinge medium weight cold rolled complete all as specified and directed.

S&F Door closer hydraulically regulated, aluminium extruded section designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

Material & labour for preparation of old wooden surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material & labour for preparation of new wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L in PCC of Type B0(1:2:4) 12.5 mm aggregate upto 1.5m clearspan, lintels, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, watertroughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

Dismantling floor, hearth or wall tiling ,dados of any description and size including cement mortar bedding (but not backing), removing serviceable tiles and staked properly to made on credit and remaining rubbish off the premises complete all as specified and directed.

Material and labour for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including provision of 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per item No-17 above but for work on vertical surfaces such as skirting, dados and risers to steps etc including backing layer of 10mm thick CM 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement line mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing the unserviceable one complete all as specified and directed.

M & L fly ash bricks modular size for masonry wall straight or curved on plan exe 6m mean radius, built in cement morter (1:6 ) complete all as specified and directed.

M&L Precast cement concrete type C-1, 1:3:6 (20mm graded stone aggregate) 40 mm thick slab flooring, bedded, and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 complete all as specified and directed.

M&L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel bars 6mm to 8mm dia in stirrups and main bar, cut to length, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including provision of 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 10mm thick CM 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed.

M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Material and labour for 10 mm rendering in cement mortar (1:6) on other than fair faces of brick wall surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coat of oil bound distemper over a coat of acrylic primer over 3mm thick white cement putty of approved make complete all as specified and directed.

Material and labour for preparation of old surfaces of walls including brooming down or steel wire brushing, scrapping down smoke soot, moulds, efflorescent salts and trading oil and greasy spots and applying of one coats of oil emulsion distemper complete all as specified and directed.

Material and labour for 16 mm thick mineral fiber or polycarbonate ceiling of size 600 x 600mm board Acoustic CAC-35, fire resist (class -A (UL), light reflectance-0.90, standard humidity resistance-99% and fine texture factory applied latex paint, including frame work for ceiling of GI frame work main tee of size 24 x 32 mm., having 0.27 mm gauge at every 1200 mm. centre to centre maximum and rotary stitched cross tee of size 24 x 27 mm, having 0.27 mm gauge at every 600 mm. c/c. and sub cross tee of size 24 x 27 mm, having 0.25 mm gauge at 1200 mm c/c. and wall angle of size 19 x 19 mm, having 0.35 mm gauge fixed to the periphery of the wall. The above grid is suspended at every 1200mm c/c. in both directions using 2.0 mm. thick pre straightened GI wire laying fine fissured butt edge complete all as specified as directed. (Make: Armstrong or euqivalent of)

Material & labour for preparation of old decotrated surfaces of wall by washing, rubbing down, stopping including brooming down smoke soot, moulds, moss and efflorescent salts and trading oil greasy spots completely and applying two coat of plastic emulsion paint over a coat of acrylic primer over 3mm thick white cement putty complete all as specified and directed

Material & labour for preparation of old decorated ceiling surfaces by brooming down,steel wire brushing, scraping down moulds,efflorescent salts and trading oil greasy spots and applying one coat of white wash on ceiling surfaces complete including filling putty/filler where ever drepression foud in ceiling complete all as specified and directed.

Material and labour for 10 mm thick vitrified ceramic tiles, double charge, dark shade, square or rectangular, polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

All as per item No. 33 above but vertical surfaces such as skirting, dados etc over 10mm thick backing layer in CM 1:4 on fair faces of brick work or concrete surfaces.

Providing and Fixing Armstrong Channelled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm(weight-8.5 kg/Sqm)made of a Moisture resistant fibre board substrate with a laminated facing as per the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut, Interior White, Alumina Pearl) and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the reverse surface has a “Helmholtz” fluted perforation with consecutive 3mm wide groove followed by 13mm of visible pane. The edges of the panel shall be “tongue-and-grooved” to fix special clips for installation and seamless visual. The back of the perforated panel shall have sound absorbing non-woven Soundtex acoustical fleece hot pressed to achieve NRC of 0.6. (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 and Humidity Resistance (RH) of 70% with camber limit less than 1mm/1000mm and bow less than 1mm/300mm.The panels shall be mounted on special aluminium splines (keel) using inside clips provided by Armstrong and approved by the Architect/ Engineer-in-Charge. INSTALLATION: - An appropriate vapour barrier (by others) shall be applied/installed on the vertical surface before the installation to properly seal against entry of any moisture. Vapour barrier (by others) shall be installed as per Manufacturer’s recommendation. Install Aluminium Extrusion of size 3000(L) x 24(H) x 15.5(W) mm fixed with clip as approved by the Architect on the solid wall/partition to provide level and plumb surface for fixing Armstrong Keel. Install Keel vertically using screws and plugs at spacing of not more than 600mm centre-to-centre. The first and last keel should not be more than 150mm from the ends. Trim the tongue of the first bottom panel and install using headless nail with groove side upward. Subsequent panels are installed with tongue side downward by engaging with each other using tongue and groove mechanism and secured by inside clip. Continue this process until required height is achieved. Shorter butt edges need to be joined using industrial/wood glue. The keel shall also be used for transition of the butt end of adjacent panel at every 7.2m. Install the Skirting (provided by others) of width 50mm or more as required by the Architect/ Engineer-in-Charge. Finish off the edges using wooden moulding of matching colour (by others). Installation should be carried out as per Armstrong recommended procedure.

Supply and fixing powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. (minimum thickness of powder coating 50 micron complete all as specified and directed. (Note- Glass shall be measured and paid separately)

Supply and fixing 6mm thick reflective toughened Sheet glass of any colour fixed to aluminum framing incl necessary fittings complete all as specified and directed and sheet glass as approved by Engr-in-Charge.

Supply and fixing vertical roller blind of any colour complete with all its accessories fixed to wall with screws and roller blind as approved by Engr-in-Charge complete all as specified and directed.

E/M PORTION Material and Labour for point wiring complete with two runs of multi-stranded copper conductor 1.5 sqmm size PVC insulated unsheathed cable 1100 Volt grade, conforming IS 694 & colour code in conduit system of wiring, drawn in including medium grade PVC conduit not less than 20 mm dia concealed, including cutting chases and making good disturbed surface complete, including single core solid conductor copper 1.5 sqmm size solid PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly drawn in same conduit complete all as specified and directed.

One light point controlled by one way switch.

One 3 pin socket outlet, 5/6 amps, on independent board.

All as per item No 39 here-in-before but with copper conductor 2.5 sqmm for One 3 pin socket outlet, 15 amps on independent board complete all as specified and directed.

S&F Modular switch 1 way 6A, 1 module complete all as specified and directed.

S&F Modular Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

S&F Modular Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F Modular switch 1 way 16A, 1 module complete all as specified and directed.

Supply and fix ceiling rose, surface bakelite,65 x 50mm, three terminals complete all as specified and directed.

S&F Modular White Cover Plate with Frame, 3 Module complete all as specified and directed.

S&F Modular White Cover Plate with Frame, 4 Module complete all as specified and directed.

S&F Modular White Cover Plate with Frame, 6 Module complete all as specified and directed.

S&F Modular Metal Flush Box 3 module complete all as specified and directed.

S&F Modular Metal Flush Box 4 module complete all as specified and directed.

S&F Modular Metal Flush Box 6 module complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed

Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed

Supply and fixing of Modular Fan regulator,120 watts complete all as specified and directed. (Make : .Crabtree/Cona/Havells)

Hanging only ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed

Material and Labour for sub main wiring complete with 2 single core multi stranded copper conductor 6 sqmm (Nominal area) PVC insulated unsheathed cable drawn in and including medium grade PVC conduit ISI Marked not less than 25 mm dia concealed, including making good distrubed surface, of wall, including single core multi stranded copper conductor 6 sqmm size as earth wire drawn in same conduit complete all as specified and directed .

Supply & fix fullyglow G5 fully diffused recessed mounted 2x2 LED luminaire with high transmitive diffuser suitable for indoor spaces complete all as specified and directed. Make: Philips Cat part No RC380B LED25S-6500G5 L60W60 PSD OD/Crompton/ havells

S&F flush mounting factory made Ekinoxe SPN DBs Double door IP-43 protection, IK-09 with Metal door with neutral bar,Earth Bar and cables ties for cable menagement fully insulated bus bar 8 way, all as specified and directed. (Cat No 607711 make -Legrand or Equivallent Make of Siemens/Schneider/L&T).

Supply and fix MCB single pole and neutral, 240 volts, 32 to 40 amps breaking capacity 10KA, ‘C’ Series. etc , complete all as specified and directed. Make : Legrand / Siemens/ Schneider/L&T

Supply and fix MCB single pole 240 volts, 6 to 32 amps, 50HZ, 10 KA. , ‘C’ series complete all as specified and directed. Make : Legrand or eqvt in Siemens/Scheinder/ L&T

M&L for earthing complete with galvanized steel earth plate 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level) with top edge of plate not less than 1.5 Mtr below normal ground level connected to earth lead wire of GI wire 4mm dia by means of nuts/bolts and washers, check nuts and washer of galvanized iron or steel including 15 mm dia GI pipe light grade upto 1.5 mtr below ground level for protection pipe ,excavation and earth work charcole dust, common salt PCC 1:3:6 type C-I using 20 mm stone aggregate for chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type BI using 20 mm graded stone aggregate reinforced with 8 mm dia TMT bars @ 75 mm c/c both ways with MS handle 12 mm dia, round ,PGI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in Plate no 3 of SSR Part I of 2009 and connected to earth test point incl testing complete all as specified and directed . Note :- Cost of earthing GI wire 4mm dia & GI pipe 25 mm upto 25m shall be included in cost of above item.

Supply and fix ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with BLDC motor of not less than 5 Star BEE rating complete all as specified and directed. Make : Havells/Crompton/Bajaj

Taking down old unserviseable tube light Fittings Complete all as specified and directed

Taking down old unserviseable 4 Way SPN DB and earth plug and socket Complete all as specified and directed

Taking down carefully copper/aluminium point wiring including sunken MS boxes (light, fans, socket or power) complete, (fittings such as switches, ceiling roses,call bell, pendants, regulators, socket etc by unscrewing from board carefully and making good disturbed surfaces of walls, floors etc complete all as specified & directed .

Taking down unserviceable sub main /Sub circuit wiring of any type and size including Steel conduit, batten wiring for necessary repair/replacement complete all as specified and directed.

Supply and fix MCB single pole and neutral enclosure with a two pin and earth plug and socket complete with and including one MCB single pole 20 amps, 240 volts complete all as specified and directed.

Material and Labour for sub main wiring complete with 2 single core multi stranded copper conductor 4 sqmm (Nominal area) PVC insulated unsheathed cable drawn in and including medium grade PVC conduit ISI Marked not less than 25 mm dia concealed, including making good distrubed surface, of wall, including single core multi stranded copper conductor 4 sqmm size as earth wire drawn in same conduit complete all as specified and directed .

Talking down Split Air conditioning 1.5 TR indoor Unit and after compete the civil work refixing including servicing alongwith change of spare parts if required the same air conditioning same place including connected acessories complete all as specified and directed .

SWAIN ENGINEARING

vaishnaveedevienterprises