Estimate for gravitational distribution 1 and 2 from OHSR tank 2 to provide surface water to villages Abhiana kalan, abhiana khurd etc in District Ropar

Excavation by mechanical means(JCB or Hydraulic excavator) in Trenches for pipe line with straight or open cutting in streets or open are including and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation, including the cost of diversion for traffic crossing over trenches for access to the houses, watching fencing, etc. and removal of surplus soil out side/inside the town involving lead upto 15 meter complete in all respect

Earth work in excavation in foundations trenches etc. in all kinds of soil where Pick-Jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm, layers with compaction including disposal of all surplus soil as directed within lead of 30 metres.

Cement Concrete 1:4:8with (i) stone ballast 20mm gauge (PCC) mixing

Reinforced cement concrete M-25 with cement @375/kg per cum hand mixed but excluding steel reinforcement centring and shuttering in foundation and Plinth

First class burnt brick work laid in cement sand mortar 1:4 in foundation and plinth

12.5 mm thick cement plaster 1:4

Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)

Cold twisted deformed (Ribbed/ Tor Steel Bar) Bars Fe 500 grade as per IS 1786-1985, for R.C.C works, where not including in the complete rate of RCC including bending and placing in postion complete.

Supply and installation of alfa valve including fittings etc complete in all aspects of 90 mm .

Supply and installation of alfa valve including fittings etc complete in all aspects of 75 mm .

Providing&fixingC.I/D.I Flangedend, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing, testing&cost of Nut ,Bolt & insertion sheet, all carriage complete (with theapproval of Engineer in charge). Class PN-1.6 as per ISI B. (d) 200mm i/d Sluice Valves flanged

Providing&fixingC.I/D.I Flangedend, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing, testing&cost of Nut ,Bolt & insertion sheet, all carriage complete (with theapproval of Engineer in charge). Class PN-1.6 as per ISI B. (e) 250mm i/d Sluice Valves flanged

Providing&fixingC.I/D.I Flangedend, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing, testing&cost of Nut Bolt & insertion sheet, all carriage complete (with theapproval of Engineer in charge). Class PN-1.6 as per ISI 315mm Sluice Valves flanged

Providing&fixingC.I/D.I Flangedend, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing, testing&cost of Nut ,Bolt & insertion sheet, all carriage complete (with theapproval of Engineer in charge). Class PN-1.6 as per ISI B. 355mm Sluice Valves flanged

Providing&fixingC.I/D.I Flangedend, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing, testing&cost of Nut ,Bolt & insertion sheet, all carriage complete (with theapproval of Engineer in charge). Class PN-1.6 as per ISI B. (h) 400mm i/d Sluice Valves flanged

Providing&fixingC.I/D.I Flangedend, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing, testing&cost of Nut ,Bolt & insertion sheet, all carriage complete (with theapproval of Engineer in charge). Class PN-1.6 as per ISI B. (i) 450mm i/d Sluice Valves flanged

Providing&fixingC.I/D.I Flangedend, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing, testing&cost of Nut ,Bolt & insertion sheet, all carriage complete (with theapproval of Engineer in charge). Class PN-1.6 as per ISI B. 500mm Sluice Valves flanged

Providing&fixingC.I/D.I Flangedend, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing, testing&cost of Nut ,Bolt & insertion sheet, all carriage complete (with theapproval of Engineer in charge). Class PN-1.6 as per ISI B. 550mm Sluice Valves flanged

Providing & fixing double air valve ISI Markedasper IS-14845 including jointing all carriages complete. (a) C.I Double air valve (Size 65mm)

Providing and laying, jointing, fixing and testing ISI Marked uPVC Pipe Lines as per ISI 4985-2000, including ., cutting, testing in the ground complete in all respects. (B) upvc pipe 4 kgf / cm2 A) 75MM

Providing and laying, jointing, fixing and testing ISI Marked uPVC Pipe Lines as perISI 4985-2000, including cutting,testing in the ground complete in all respects.B) upvc pipe 2.5 kgf / cm2 A) 90MM

Providing and laying, jointing, fixing and testing ISI Marked uPVC Pipe Lines as per ISI 4985-2000, including , cutting, testing in the ground complete in all respects. B) upvc pipe 2.5 kgf / cm2 A) 160MM

Providing and laying, jointing, fixing and testing ISI Marked uPVC Pipe Lines as per ISI 4985-2000, including , cutting,testing in theground complete in all respects.B) upvc pipe 2.5 kgf / cm2 A) 200MM

Providing and laying, jointing, fixing and testing ISI Marked uPVC Pipe Lines as per ISI 4985-2000 including cutting,testing in the ground complete in all respects. B) upvc pipe 2.5 kgf / cm2 A) 250MM

Providing laying upvc pipe as per ISI-4985(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification 1) 125mm @ 2.5 kg/sqcm

Providing laying upvc pipe as per ISI-4985(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification 2) 140mm @ 2.5 kg/sqcm

Providing laying upvc pipe as per ISI-4985(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification 3) 180mm @ 2.5 kg/sqcm

Providing laying upvc pipe as per ISI-4985(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification 4) 225mm @ 2.5 kg/sqcm

Providing laying hdpe pipe as per ISI-4984(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification dia 355mm (2.5 kgf)

Providing laying hdpe pipe as per ISI-4984(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification dia 400 mm(2.5 kgf)

Providing laying hdpe pipe as per ISI-4984(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specificationdia 450 mm(2.5 kgf)

Providing laying hdpe pipe as per ISI-4984(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification dia 500mm (2.5 kgf)

Providing and laying, jointing, fixing and testing ISI Marked uPVC Pipe Lines as per ISI 4985-2000, including ., cutting, testing in the ground complete in all respects. B) upvc pipe 4 kgf / cm2 A) 90MM

Providing and laying, jointing, fixing and testing ISI Marked uPVC Pipe Lines as per ISI 4985-2000 including . cutting, testing in the ground complete in all respects. B) upvc pipe 4 kgf / cm2 A) 160MM

Providing and laying, jointing, fixing and testing ISI Marked uPVC Pipe Lines as per ISI 4985-2000, including cutting, testing in the ground complete in all respects. B) upvc pipe 4 kgf / cm2 A) 200MM

Providing and laying, jointing, fixing and testing ISI Marked uPVC Pipe Lines as per ISI 4985-2000, including , cutting, testing in the ground complete in all respects. B) upvc pipe 4 kgf / cm2 A) 250MM

Providing laying upvc pipe as per ISI-4985(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification 2) 140mm @ 4 kg/sqcm

Providing laying upvc pipe as per ISI-4985(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification 3) 180mm @ 4 kg/sqcm

Providing laying upvc pipe as per ISI-4985(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification 5) 280mm @ 4 kg/sqcm

Providing laying hdpe pipe as per ISI-4984(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification dia 315 mm (4 kgf)

Providing laying hdpe pipe as per ISI-4984(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification dia 355 mm(4 kgf)

Providing laying hdpe pipe as per ISI-4984(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification dia 450 mm (4 kgf)

Providing laying hdpe pipe as per ISI-4984(ISI marked with the prior approval of engineer-in-charge ) along the trenches and laying the same in trenches to correct alignment and gradients,cutting,jointing, and testing complete as per specification dia 560mm(4 kgf)

Providing and fixing elbow/bends 90 degree dia 75mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 90 degree dia 90mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 90 degree dia 125mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 90 degree dia 140mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 90 degree dia 160mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 90 degree dia 180mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 90 degree dia 200mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 90 degree dia 225mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 90 degree dia 250mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 90 degree dia 280mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends dia 90 degree 315mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 45 degree dia 75mm 6kgf/sqcm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 45 degree dia 90mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 45 degree dia 125mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 45 degree dia 140mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 45 degree dia 160mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 45 degree dia 180mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 45 degree dia 200mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 45 degree dia 225mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 45 degree dia 250mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 45 degree dia 280mm as per IS code 4985 complete in all respect.

Providing and fixing elbow/bends 45 degree dia 315mm as per IS code 4985 complete in all respect.

Providing and fixing Equal tee dia 75mm as per IS code 4985 complete in all respect.

Providing and fixing Equal tee dia 90mm 6kgf/sqcm as per IS code 4985 complete in all respect.

Providing and fixing Equal tee dia 125mm as per IS code 4985 complete in all respect.

Providing and fixing Equal tee dia 140mm as per IS code 4985 complete in all respect.

Providing and fixing Equal tee dia 160mm 6kgf/sqcmas per IS code 4985 complete in all respect.

Providing and fixing Equal tee dia 180mm as per IS code 4985 complete in all respect.

Providing and fixing Equal tee dia 200mm as per IS code 4985 complete in all respect.

Providing and fixing Equal tee dia 225mm as per IS code 4985 complete in all respect.

Providing and fixing Equal tee dia 250mm6kgf/sqcm as per IS code 4985 complete in all respect.

Providing and fixing Equal tee dia 280mm as per IS code 4985 complete in all respect.

Providing and fixing Equal tee dia 315mm as per IS code 4984 complete in all respect.

Providing and fixing Equal tee dia 355mm as per IS code 4984 complete in all respect.

Providing and fixing Equal tee dia 400mm as per IS code 4984 complete in all respect.

Providing and fixing Unequal tee dia 200*160 mm as per IS code 4985 complete in all respect.

Providing and fixing Unequal tee dia 200*125 mm as per IS code 4985 complete in all respect.

Providing and fixing Unequal tee dia 200*90 mm as per IS code 4985 complete in all respect.

Providing and fixing Unequal tee dia 160*125 mm as per IS code 4985 complete in all respect.

Providing and fixing Unequal tee dia 160*90 mm as per IS code 4985 complete in all respect.

Providing and fixing Reducer Size 90mm to 75mm per IS code 4985 complete in all respect.

Providing and fixing Reducer Size 140mm to 125 mm as per IS code 4985 complete in all respect.

Providing and fixing Reducer Size 140mm to 160 mm as per IS code 4985 complete in all respect.

Providing and fixing Reducer Size 200mm to 160 mm as per IS code 4985 complete in all respect.

Providing and fixing Reducer Size 225mm to 200 mm as per IS code 4985 complete in all respect.

Providing and fixing Reducer Size 250 mm to 200 mm as per IS code 4985 complete in all respect.

Providing and fixing Reducer Size 250mm to 225 mm as per IS code 4985 complete in all respect.

Providing and fixing Reducer Size 315mm to 225 mm as per IS code 4985 complete in all respect.

Providing and fixing Reducer Size 315mm to 250 mm as per IS code 4985 complete in all respect.

Providing and fixing Reducer Size 355mm to 250mm as per IS code 4985 complete in all respect.

Providing and fixing Reducer Size 355mm to 315 mm as per IS code 4984 complete in all respect.

Providing and fixing Reducer Size 400mm to 355 mm as per IS code 4984 complete in all respect.

Providing ,and fixing cast iron adaptor of 6kg/cm2 pressure including testing,comisioning ,cpmplete in all respect to the satisfaction of engineer encharge. Dia 550

Providing ,and fixing cast iron adaptor of 6kg/cm2 pressure including testing,comisioning ,cpmplete in all respect to the satisfaction of engineer encharge. Dia 500

Providing ,and fixing cast iron adaptor of 6kg/cm2 pressure including testing,comisioning ,cpmplete in all respect to the satisfaction of engineer encharge. dia 450 mm

Providing ,and fixing cast iron adaptor of 6kg/cm2 pressure including testing,comisioning ,cpmplete in all respect to the satisfaction of engineer encharge.dia 400 mm

Providing ,and fixing cast iron adaptor of 6kg/cm2 pressure including testing,comisioning ,cpmplete in all respect to the satisfaction of engineer encharge. Dia 355 mm

Providing ,and fixing cast iron adaptor of 6kg/cm2 pressure including testing,comisioning ,cpmplete in all respect to the satisfaction of engineer encharge. Dia 315 mm

Providing ,and fixing cast iron adaptor of 6kg/cm2 pressure including testing,comisioning ,cpmplete in all respect to the satisfaction of engineer encharge. Dia 250 mm

Providing ,and fixing cast iron adaptor of 6kg/cm2 pressure including testing,comisioning ,cpmplete in all respect to the satisfaction of engineer encharge. Dia 200 mm

Providing and fixing MS Service saddle of dia 75mm*50mm including testing ,comissioning complete in all respect to the satisfaction of Engineer enchage.

Providing and fixing MS Service saddle of dia 90mm*50mm including testing ,comissioning complete in all respect to the

Providing and fixing MS Service saddle of dia 125mm*50mm including testing ,comissioning complete in all respect to the satisfaction of Engineer enchage.

Providing and fixing MS Service saddle of dia 140mm*50mm including testing ,comissioning complete in all respect to the satisfaction of Engineer enchage.

Providing and fixing MS Service saddle of dia 160mm*50mm including testing ,comissioning complete in all respect to the satisfaction of Engineer enchage.

Providing and fixing MS Service saddle of dia 180mm*50mm including testing ,comissioning complete in all respect to the satisfaction of Engineer enchage.

Providing and fixing MS Service saddle of dia 200mm*50mm including testing ,comissioning complete in all respect to the satisfaction of Engineer enchage.

Providing and fixing MS Service saddle of dia 250mm*50mm including testing ,comissioning complete in all respect to the satisfaction of Engineer enchage.

Providing, laying, jointing, fixing and testing ISIMarkeduPVCPipewithG.I. specialsas per ISI-4985, includingcost of G.I. specials such as tees, bends, sockets, elbows etc. testing inside building complete. uPVC Pipe 6 Kgf/cm2 50 mm dia

Providing and fixing Reducer Size 65to 50 mm as per IS code 4984 complete in all respect.

Any Other Items

Please Enable Macros to View BoQ information