Library furniture and modication at HBCHRC

Removing of doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Fixing chowkhat in existing opening in brick/ RCC wall with dash fasteners/Chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including Cost of dash fasteners/ chemical fastener.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Lintel concrete Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for :Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size 300x 300/600x600 or as per requirements

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre.

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Dismantling tile,granite work in floors & wall and false ceiling including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Making the opening in brick masonry for door/ window/ clerestory window including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge.

Supplying and fixing: Fabric Cushion Reading Chair : visitor chair with ergonomic design, comfortable and aesthetically appealing. Seat and Back: The seat and back are made up of hot pressed 15mm plywood and moulded polyurethane foam upholstered with bric. The backrest is designed with contoured lumbar support which provides support to spine and leaves shoulder free for easy movement. Arm Rest: The chair shall be supplied with polyurethane fixed arms on MS cantilever stand which is completely joint with seat and back Stand: The chair stand is cantilever shape made up of MS round pipe of dia 25.4mm having thickness 2mm that provides great comfort. The stand is duly powder coated with epoxy powder coating having thickness 60 microns. PVC shoes are provided at the bottom of the stand to prevent any scratches on the floor.The chair dimensions are as follows: Overall Height: 1050mm Outer Width: 575mm Seat Height from ground: 530mm Seat Width: 490mm Seat Depth: 480mm Back height from seat: 550mm Back Width: 490mm All dimensions have a tolerance of ±10mm.

Providing and placing TABLE 1350(W) X 600(D) X 750(H) Office table with a robust structure, good stability and a solid thicker look with levelling adjustment to adjust with the uneven floor surface. TOP:- 54mm thick dark colored table top made up of 18mm thick pre-laminated particle board with two battens of same thickness fixed along two long edges from the bottom side which provide decorative twin colored thick edge look. The decorative trim to be connected in a way to form connectivity of 45 degrees with gable end. Support stiffener made up of M.S. rectangular pipe of 20X40X0.8mm thickness is provided for extra support for the Top of the length of 1200mm and above. LEG:- 18mm thick leg or gable end made up of 18mm thick pre-laminated particle board with two battens of same thickness fixed to it from front side providing straight as well as a consolidated thicker look to the table with two colored edge profile. MODESTY:- Modesty panel of lighter shade made up of 18mm thick pre-laminated particle board providing stability to structure and allow sufficient leg privacy to the user. The product must be from a Manufacturer having ISO 9001,ISO 14001,ISO 45001, Green Pro, Latest BIFMA 5.1 certificates for few of its products

Supply, Fitting & Fixing of computer / study table with partition having overeall dimensions Width 900MM Depth 600MM Height 750MM Work Top- Work top shall be made 25mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Table top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section Understructure- C-type leg shall be made of vertical member 50X50X1.6mm thick and horizontal member of 40x40x1.6mm thick M.S. pipe confirming IS-Grade 4932 with powder coated finish up 50 to 60 Micron. Legs shall be fitted to the ground with M8 screw leveler with the height adjustment up to 12mm to 15mm.Cross member shall be made of 40mm X 40mm X 1.6mm MS LIP section with powder coated finish confirming to IS 13871:1993. Cross members shall be mounted by end brackets. Cross member end bracket shall be made of 3mm thick IS 513: 2008 CRCA sheet with powder coated finish up 50 to 60 Micron. Aluminum privacy panel section is constructional member of understructure shall be made of Aluminum extrusion confirming the IS 733:1983. Wire management-Electrical wires shall be carried from 100x100mm vertical duct, vertical duct shall be made of 0.7mm CRCA sheet confirming to IS 513:2008. Horizontally wire shall float in 100x90 mm cable tray for one sided workstation and 210x90mm cable tray for back to back workstation, Cable tray shall be made of 0.7mm CRCA sheet confirming to IS 513:2008. Cable tray can be used as side access or top access. In top access we can use access flap for switch mounting. Wire manager or PVC grommet can be given as a option. In top access switch plate is provided on cable tray for mounting electrical standard switch plate. CRCA connector used between cable trays.Perforated Modesty Panel- For one side workstation modesty made up of CRCA 0.8mm sheet and for back to back work station modesty made up of CRCA 1.5mm thick confirming to IS 513: 2008 with powder coated finish up 50 to 60 Micron. Modesty shall be available in height of 450mm, 600mm and 750mm on one side workstation and 450mm height shall be given in back to back workstation. Modesty brackets shall be used to mount the offered modesty.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ISO 45001 ,Latest BIFMA 5.1,Green Pro certificates for few of its products

Supplying and fixing:collaborative seating having overall length of Approx 4.5 rmt (+/- 500 mm)curve sofa :It is based on infinite combinations, round or angular the end element gives a over hang look to the combination, Table can be integrated to add extra space for magazine, Coffee Cup or Laptop working. This is a great space filling concept with modular formats. Back Panel: The substructure is made from combination of White Ash wood, Springs, Elastomers and foams.Material: Polyurethane Foam with timber substrate

Supplying and fixing: NEWSPAPER STAND with storage -1555(W) X 1100(D) X 1200(H) End Panels, Sloping top panel, Middle panel, and Shutter doors to be made up of 25 mm thick pre-laminated interior grade medium density fiberboard board. Structural Base Frame Stand to be made in 25mm X 50mm powder coated MS box section, welded at joints. SS solid rectangle section of 5mm X10mm used for divider and slope end. Lamination: Factory-pressed Light Teak Laminate in wood grain finish to be used for all lamination. All Laminates are to be applied only after the approval of the Laminate sample. Note:1. All medium density fiberboard shall be of interior grade and shall conform to IS:12406:2003. 2. Unless specified otherwise, all pre-laminated medium density fiberboard should have the same laminate on both sides. 2 All pre-laminated medium density fiberboard shall have a 2 mm thick matching edge band fixed on all sides under pressure with hot melted glue. 3. Knockdown construction using standard hardware to be used

Supplying and fixing: MAGZINE STAND-800(W) X 700(D) X 1500 End Panels, Sloping Base panel, Top panel, Sloping inner panel, and Shelf base to be made in 25 mm thick pre-laminated interior grade medium density fiberboard board. Structural Base Frame Stand to be made in 25mm X 50mm powder coated MS box section, welded at joints. Note: 1. All medium density fiberboard shall be of interior grade and shall conform to IS:12406:2003. 2. Unless specified otherwise, all pre-laminated medium density fiberboard should have the same laminate on both sides. 3. All pre-laminated medium density fiberboard shall have a 2mm thick matching edge band fixed on all sides under pressure with hot melted glue. 4. Knockdown construction using standard hardware of Hettich, or equivalent make after approval by Authority, to be used

Supplying and fixing: sofa overall dimensions 1200LX775DX890H Frame : The sofa’s frame is made from solid, sustainable wood and commercial ply Upholstery: Fabric upholstered back and seat Base-frame: Natural wooden frame upholstered in fabric Privacy Screen: Screen frame is made up of 19x19x2mm thick square pipe and dia 19mm round pipe

Supplying and fixing: HIGH TABLE - 1500W X 500D X 1050H MM. TABLETOP - It is made of 25 mm thick Calibrated PlY with machine pressed PVC edge band on all sides. UNDERSTRUCTURE -SPLAYED LEG constructed of 40X40X1.6 mm thick MS Pipe with caps & levellers .Cross member made of 40mm X 40mm X 1.6mm MS pipe with .Cross members are mounted by cross member end brackets

Supply and installation of center table TOP 1200 mmdia X 750mmHeight- Is made up of made 25mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Reversed chamfering is done on all sides for the table and chamfered area is sealed by white foil. Top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section Understructure- Leg base is made up of 8mm thick SS sheet confirming IS grade 202 in mirror finish having a base length of 500mm or 750mm. Legs are fitted to the ground with 52.6x19.3mm Nylon bush which is having 0.5R on the corner in standard grey colour (RAL 7042). Vertical member is made up laser cut MS Ø76 X 1.6MM THK SS pipe confirming IS grade 202 in mirror finish having height of 522mm. Ø72x3mm CRCA sheet is welded at the top of vertical member on this plate M8 nut is welded from back side. Leg base and vertical member are welded by MIG welding confirming to IS standard IS 816:1969 and it is welding also tested as per the IS grade IS816:1970. Top support plate is made up of 3mm thick SS sheet confirming IS grade 202 in mirror finish. Top support plate is connected leg vertical by using CSK Head M8x25 Screw .

Supplying and making the customize Book shelf as per attached design/drawing with 18 mm ply and minimum 1 mm thick sunmica including of cutting, wall mounting, required hardware cost and labour charges as per site requirements.

Providing and fixing of 30 mm thick Second class teak wood door shutter using 8 mm thick toughen glass, moulded beading strips, PU polishing and including of heavy duty Floor spring,lock all hardware complete as per site requirement.

Supplying and fixing: Low height Aluminium Partition: Providing and fixing 50-60 micron Powder coated aluminium partition to the required height partly glazed and partialy panneled or fully glazed of fully panneled using aluminium section of approved make heavy quality section 3" x 1.5" / or as approved by EIC . The Aluminium section shall be electro statically polyster powder coated/ Satin finish anodizing of approved shade/ colournfor bottom, top, middle and vertical rails at required intervals panneling with 12 mm thick Nova pan or Ancholam both side pre-laminated board/glass fixed with sloping aluminium biding around with neoprine gasket glazing with 5mm frosted/ plain glass of approved make like triveni, shri Vallabh/J/A/G pilkinten fixed with aluminium channel beeding two way PVC lining/ rubber gasket to ensure water teightness and no rattaling including providing necessary fittings as specified and directed . Complete in all respect at specific locations as per direction of Engineer in Charge.

Supplying and fixing: Wooden wall panelling work: Providing and fixing of wall paneling with making of wooden /aluminium frame and fixing of 18 mm Ply , 4 mm polished veneers, and making the 3 mm grooving with paint in the Veneers at each 1 m distance Horizontally and verti

caly, 100-150 mm wide wooden frame with polished shall e fix on top as per direction of Enginner-In-Charge.

Supplying and fixing: A grade thick wall paper sheets on walls of library includin cariage , pasting matarial etc. complete in all respect as per site requirements.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable of DELTON/POLYCAB/RR KABLE/FINOLEX in the existing surface/ recessed steel/ PVC conduit as required. 4 pair UTP CAT 6- 1 run of Cable

SITC of RJ 45 I/O jack with cover plate of required size including PVC base Box. Schneider/MOLEX/Belden make

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supply and erection of PVC Channel (uPVC Trunking) with cover of various sizes (On Surface) on wall, Flat angle, internal & external angle, Flat Tee, End cap and mounting boxes including the cost of joint cover, fixing and other petty material etc.:- PVC Channel (uPVC Trunking) 50mm x 50mm

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel/medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C (Primary Point upto 12.5 Mtrs.)

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel/PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. Group C (Secondary Point upto 10.5 Mtrs.)

Supplying and fixing suitable size GI/PVC box with modular plate and cover in FRLSont on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI/PVC box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 amps modular socket outlets and 2 nos 5/6 amps modular switches, connection etc. as required.

6 A to 32 A ratings , SP MCB “C” curve, 10 KA breaking capacity

6 A to 32 A ratings , DP MCB, “C” curve, 10 KA breaking capacity

LIGHT Fixtures Supply of LED fixtures having minimum 100Lm/W on wall/beam/slab by means of bracket ,anchor fastener suspended from slab/beam by means of 19 mm dia conduit pipe/down road,ball and socket arrangement,flexible twisted wire/ flexible cable connection etc and GI chain for recessed mounting fitting complete in all respect as directed by Engg. in charge and Wipro make or any other approved make as per instructions of EIC.

SITc of LED Profile Light complete with driver and fixing arrangement.

SITC of 24W LED striplight (Warm white) including connetion, jointer, connecter, driver, etc.

SITC of 6W Slim COB downlighter (Warm white) including connection, etc.

SITC of Wall mount Braket light with warm white LED lamp.