PROVN OF GUARD ROOM, BATHROOM AND TOILET AND ADDN/ALTN OF GUEST ROOM NO 3, 4, 5 AT NCC OFFICERS MESS AND SPECIAL REPAIRS OF P-4B AND P-4GH UNDER GE (W) COLABA, MUMBAI

Amount

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft/loose soil all as specified & directed .

Excavation in trenches, not exc 1.50m wide and not exc 1.5m in depth etc not exceeding 10 Sqm on plan for shafts, cesspits, manholes, pier holes, foundation etc and getting out in hard/dense soil all as specified and directed.

Excavation in trenches, not exc 1.50m wide and exc 1.5m but nexc 3.0 mtr in depth etc not exceeding 10 Sqm on plan and getting out in hard/dense soil all as specified and directed.

M&L for Treating the bottom and sides of excavation at the rate of 5 ltr of emulsion per sqm of surfaces area all as specified and directed.

M&L for termite treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) all as specified and directed.

M&L for termite treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface area all as specified and directed.

M&L for termite treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area all as specified and directed.

M&L for treating the soil along with external perimeter of building at the rate of 2.25 ltr of emulsion per mtr of the perimeter wall all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in cement concrete in foundations, filling and mass concrete all as specified and directed.

Returning filling in and including spreading levelling watering and well ramming in layers n exc 25cm thick all as specified and directed.

Removing excavated soil, removing the retreived debris out side MD land 25 KM away all as specified and directed.

M&L 25 mm thick damp proof course in CM (1:2:) mixed with integral water proofing compound @ 3% by weight of cement with nessery formwork and applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cum per sqm all as specified and directed.

M&L RCC work as in columns, beams, slabs, retaining walls, chajja, railing or similiar work using ready mix M-30 grade (Design Mix) delivered on banker from authrorised manufacturung plant mixed with required plastesizer plant using 20 mm nominal size crushed stone aggregate necessary equipment needed to carry out the work for finishing (compactor, vibrator, Trowel, groove cutter pump for pouring concrete with provision for joints all as specified and as directed by Engineer-in-Charge. Note : Item will be inclusive of Curing compound and pumping which will be spread uniformly over fresh concreting.

Use & waste special water tight centering and shuttering including bolting, strutting, propping etc. so as to with stand a pressure of 0.1 Mpa including removal of form work at all locations including beams, columns, slabs, walls, foundations, footings, landings, stairscase, balconies etc or in any similar work all as specified and directed.

M&L mild steel TMT bars 8-10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height all as specified and directed.

M&L mild steel TMT bars any dia in stirrups, spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed

M&L brick work with sub class "B" bricks, straight or curved on plan exc 6 m mean radius built in CM 1:6 all as directed & speicified

M&L brick work with fly ash bricks, straight or curved on plan exc 6 m mean radius built in CM 1:6 of brick work of stone/boulder masonry, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work and precast concrete articles all as specified and directed.

M&L Brick work with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 all as specified and directed.

M&L Ready mix plaster for external plastering 25 mm thick in two coats of 15 mm base coat and 10 mm finishing coat on brick wall or concrete surfaces and cement mortar with WPC 3% by weight of cement all as specified and directed. (WPC shall be measured and paid separately)

Supply only integral water proofing compound,

M&L Ready mix plaster for internal plastering 15 mm thick in two coats of 10 mm base coat and 5 mm finishing coat on brick wall or concrete surfaces including use of scaffolding and removing debris outside MD land all as specified and directed. Name of Manufacturer: M/s Premier Floor to Roof Materials pvt. ltd/ M/s Walplast Products pvt. ltd/ M/s Ultratech Cement Ltd/M/s Sound buildcare pvt. Ltd/ or other approved equivalent make.

M&L Ready mix plaster for ceiling plastering 5 mm finishing coat on brick wall or concrete surfaces including use of scaffolding and removing debris outside MD land all as specified and directed. Name of Manufacturer: M/s Premier Floor to Roof Materials pvt. ltd/ M/s Walplast Products pvt. ltd/ M/s Ultratech Cement Ltd/M/s Sound buildcare pvt. Ltd/ or other approved equivalent make.

Providing & applying anti algalwater-based Elastomeric exterior wall finish on old as well as newly plastered surface including surface preparation, applying suitable wall Primer and application of two coats of paint by brush all as specified and directed. Make:- preferred make Dr Fixit Rain coat classic,Asianpaints, Berger, Truworth, Apurva or equivalent Note : Height of Bldg Up to fourth floor.

M&L for preparation of newly plastered wall surfaces and applying a coat wall care putty (Birla White Wall care or equivalent) 2mm thick ( in two coat 1 mm each ) avg on plastered surfaces rubbing with sand paper, preparatory to distempering and applying two coats of acryilic emulsuion over a coat of alkali resistant priming paint all as specified and directed. Make : Apcolite Premium Emulsion

M&L for two coats of smooth interior acrylic emulsion with Texture finish having VOC less than 50 grams per ltr complying LEEDS criteria @1 ltrs (unndiluted) /10 sq mtrs diluted with water in 2:1 ratio applied over priming coat with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in both the coats of paint as per manufacturer instructions all as specified and directed. Make -Apcolite Premium Emulsion

S&F factory made single extruded WPC (Wood polymer composite) soilid door frames/chowkhat comprising of 125 x 65 mm size applying PVC solvent cement and screwed with full body threated star headed SS screws having minium frame density of 750 Kg/Cum and resistance to spread of flame of class A category with property of being termite/borer proof water/moisture proof and fire retardant and fixed in position with MS hold unserviceable fast/lugs/ss dash fasteners of required dia nad length all as specified and as directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door Frames/Chowkhat comprising of 100 mm X 50 mm size applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length all as specified and directed

S & F factory made extruded WPC (Wood Polymer Composite) solid door Frames/Chowkhat comprising of 62 mm x 32 mm size applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum

S & F factory made 28-30 mm thick single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size, modulus of elasticity 850 N/mm* and resistance to spread of flame of class A category with property of being termite/borer

M&L for minor cleaning work, removal of loose concrete and filling cracks with polymer modified mortar using SmartCare RP or Epoxy Mortar and supplying and applying High performance hybrid polyurea elastomeric waterproofing coating cold applied of spray / brush applied, SmartCare Ultron liquid membrane with an elongation of 600% and tensile strength of 12.6 N/mm2 as per ASTM D 2370, crack bridging ability of 3mm as per ASTM C1305, shore A Hardness of min. 75 as per ASTM D 2240. The system includes final base preparation, epoxy primer application and applying SmartCare Ultron or approved equivalent in two coats at 1.5 kg per Sqm etc, complete as per Manufacturer specifications. Supplying and applying High performance hybrid polyurea elastomeric waterproofing coating cold applied of spray / brush applied, SmartCare Ultron liquid membrane with an elongation of 600% and tensile strength of 12.6 N/mm2 as per ASTM D 2370, crack bridging ability of 3mm as per ASTM C1305, shore A Hardness of min. 75 as per ASTM D 2240. The system includes final base preparation, epoxy primer application and applying SmartCare Ultron or approved equivalent in two coats at 1.5 kg per Sqm etc, complete as per Manufacturer specifications over and including average thick 75 mm delievered with RMC Banker Pouring with pumping system PCC (1:2:4) type B-0 for padding on roof surfaces using liquid water proofing compound applying while concrete is green and all other similar works complete all as specified and directed (SmartCare Ultron Hybrid Polyurea /DR Fixit roof seal ultra or any equivalent). NOTE: PU treatment shall be done by authorized applicator and work shall be executed in the presence of company rep.

M&L for machine cut, polished cudappah stone work 20 to 25 mm thick (table rubbed and polished) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and rounding the edges as in kitchen platform, flooring and all other similar works , including laying over 15mm thick cement mortar (1:6) all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

M&L for GI frame work for seamless ceiling 600x600mm grid size comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and directed.

Material and labour 8 mm thick Exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid (frame work for ceiling shall be measured and paid separately) fixed to aluminum frame work in ceiling and all other similar works complete all as specified and directed.

S&F wooden coloured anodized aluminium sections as per relevant IS for doors, windows, ventilators, door partition including fabrication of frame shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc. including all accessories such as glazings clips, provn of AC opening and rubber beadings for fixing glass panes in frame all as specified and directed. Note : (i) Glass panes will be measured & paid separately . (ii) The quoted rate shall be inclusive of cost of rubber beading and glazing clips. However it will be not be weighed and not paid separately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate. (iv) Joint filling shall be completed using silicon gun.'.

M&L 5.5 mm thick sheet glass, ordinary quality and glazing with aluminium beads and rubber gaskit in square exc 0.5 sqm in each pane frosted on one side all as specified and directed.

M&L 4mm thick frosted glass, ordinary quality and glazing with aluminium beads and rubber gaskit in square exc 0.5 sqm in each pane frosted on one side all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples over wooden beading all as specified and directed.

S&F Aluminium anodized deco grill Cat No DG-916, 7.5 mm thick, cut to required size/shape and fixed in position with aluminium beading all as specified and directed.

S&F factory made 35 mm thick flush shutter solid core construction with block board core & plywood face panels commercial type on both sides laminated incl 5mm thick teakwood leaping alround complete all as specified & directed.

S & F factory made 35 mm thick machine pressed architects veneer designer ply lam both side flush door shutter, solid core construction with block board core incl 5mm thick teakwood lipping alround with centrally locking arrangement with Lock of make Godrej of Link, 7 lever with Door eye, PVC buffer, door stopper and self-closing Device complete all as specified and as directed by Engr-in-Charge

S&F 35mm thick second class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. with two Nos Muntines edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S&F 18mm thick Marine Plywood laminated of any colour with High glossy acrylic sheet of 3mm thick, grade I as per IS 14587, for frame and shutter for kitchen cabinets all as specified and directed.

S&F medium weight, cold rolled mild steel, SS finish, (Partial overlay/fully overlay of any type) diameter of cup 35mm, Hinge cup depth 11.5mm, soft-closing all as specified and directed. Make : Godrej Kitchen fittings /Haffle or asian sleek

S&F Plastic tyres and steel ball bearing 25 mm dia with load capacity 40 Kg cabinet drawer roller all as specified and directed by Engr-in-charge (For built in cup boards). Door set/sleek(Asian Paints) or equivalent as approved by GE.

S&F stainless steel cabinet drawer multi lock single latch 40 mm size all as specified and directed. (For built in cup boards). Make: Door set/sleek(Asian Paints) or equivalent as approved by GE.

S&F 50 mm magnet PVC coating MS cabinet drawer all as specified and directed by Engr-in-charge (For built in cup boards). Make: Door set/sleek(Asian Paints) or equivalent as approved by GE.

S&F MS with black coating 550 mm long with load capacity 40 Kg cabinet drawer channel fixing with screws all as specified and directed. (For built in cup boards). Make: Door set/sleek(Asian Paints) or equivalent as approved by GE.

S&F 600 mm long brass, barrel tower bolt of extruded section all as specified and directed.

S&F 200 mm long bras barrel tower bolt of extruded section all as specified and directed.

S&F 200 mm long brass handle of extruded section all as specified and directed.

S&F 300 mm long brass designer sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections all as specified and directed.

S&F Stainless steel coloured 100mm long butt hinges, medium weight all as specified and directed.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel all as specified and directed.

S&F Aluminium 75 mm long Butt hinges L shape medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 200mm long Aluminium anodised, barrel tower bolts of ex- truded section all as specified and directed.

S&F 200mm long anodised aluminium alloy handles, fabricated type all as specified and directed.

S&F MS 300 mm long ordinary rat tail rod pattern spring including roller and plate all as specified and directed.

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 all as specified and directed.

M&L for two coats of synthetic enamel paint on steel surfaces, over a coat of red oxide primer including preparation of new steel surfaces 10cm in width or grith not ohter wise described all as specified and directed.

S&F joist, channel, angle, or tee sections, or MS flats fixed independantly without connecting plates, etc. Fe 410-W (Gde-E- 250) quality- A (cut to ordinary lengths i.e within 20mm of length indicated) as in frame work for galvalume / CGI chajjas all as specified and directed.

S&F structural steel work in tubular/square tube trusses including special shaped washer, gusset/bearing plate using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 all as specified and directed.

S&F 25 mm dia decorative fancy type SS curtain rods and all other connected works all as specified and directed.

S&F 25 mm dia decorative fancy type SS curtain rod brackets all as specified and directed.

S&F two piece EWC water closet Single Piece EWC 640 X 360 x 685 mm including Cistern, PP Soft close seat cover and hinge, fitting accesorries set with cistern fittings, fixed with waste coupling and waste pipe all as specified and directed. Make : Cat Part No SLS-WHT-6851P180PP having P Trap of Jaquar or Equivalent in Cera / Parryware / Prayag

S&F 15 mm bore fancy type angular valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions all as specified and directed. Make:- ESS ESS CROMA Cat Part No C 204 or Equivalent of Jaquar/Paryag

S&F 15 mm bore fancy type concealed stop cock (regular body) cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions all as specified and directed. Make:- ESS ESS CROMA Cat Part No C 332 or Equivalent of Jaquar

S&F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed screwed both ends for iron pipe or for unions all as specified and directed.

S&F PVC connection 15mm size PTMT nuts of length 450 mm all as specified and directed.

S&F 15 mm bore fancy type wall mixer with 115 mm long bend pipe for connection to overhead shower (with bush and piston Divertor fittings) with aerator all as specified and as directed by Engr-in-Charge. Make:- Cera Cat Part No F 1015401 or of equivalent model in other makes as listed in Appendix 'C.Equivalent of JAQUAR/ESS ESS

S&F 15 mm bore fancy type bib taps long body (two in one) cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule all as specified and directed. Make:- Cera Cat Part No F 1015163 or of equivalent model in other makes as listed in Appendix 'C.

S&F 15 mm bore fancy type bib taps cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule all as specified and directed. Make:- ESS ESS CROMA Cat Part No C 202B or Equivalent of JAQUAR/PRAYAG

S&F 15 mm bore fancy type health faucet with SS hose all as specified and as directed by Engr-in-Charge. Make:- Cera Cat Part No F 8030106AB or of equivalent model in other makes as listed in Appendix 'C.

S&F fancy type CP towel rail 61 cm long all as specified and as directed by Engr-in-Charge. Make:- Cera Cat Part No F 5007101 or of equivalent model in other makes as listed in Appendix 'C.

S&F CP towel ring all as specified and directed. Make:- Cera/ Jaquar/Kajiara Kerovit

S&F CP soap dish all as specified and as directed by Engr-in-Charge. Make:- Cera Cat Part No F 5002106 or of equivalent model in other makes as listed in Appendix 'C.

S&F CP toilet paper holder all as specified and directed. Make:- Cera / Jaquar/ kerovit.

S&F sheet glass corner shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long all as specified and directed.

S&F 15 mm bore overhead shower of size 300x300 mm single flow (ABS body chrome plated with grey face plate) with rubit cleaning system including shower arm 200 mm long (stainless steel) square shape with wall flange all as specified & directed. Make:- Cera Cat Part Not F7010506AB or Equivalent of Jaquar

S&F stainless steel grating round 125mm size of anti- cockroach, anti-clog, anti faul all as specified and directed.

S & F wash basins, vitreous china, white, flat back, of size 550mm x 400mm x 140mm or nearest size conforming to model 'CALBURT' Cat No. S2020137 of CERA or of equivalent model in other makes as listed in Appendix 'C, with and including cast iron brackets (embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws), 32 mm nominal size, copper alloy, nickel chromium plated finish waste fittings, including painting of fittings and brackets, sealing gap between wall and table top basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings etc. with silicone sealant complete all as specified and directed by Engineer-in-Charge.

S&F in repairs wall mounted water closet pan of size 520x360x410mm fixed with anchor fastener, outlet pipe & accessories of size all as specified and directed. Make : Cat Part No20104 of Hindware or equivalent in Cera / Parryware.

M&L for fancy type 15 mm bore central hole basin mixture with 'U' shaped round casted spout with 3" long pipe connection with aerator all as specified and directed. Make : Jaquar Cat Part No CON-169KNB or Equivalent of Prayag / Cera.

Supply and laying of CPVC pipes 20 mm SDR 11 & Plain CPVC SDR 11 with all fittings laid in wall,floor, trenches and ceiling with taking down existing all as specified and directed

Supply and laying of CPVC pipes 16 mm SDR 11 & Plain CPVC SDR 11 with all fittings laid in wall, floor, trenches and celling with taking down existing all as specified and directed

Cutting chases, pinning in and making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good, cutting n, exc. 10cm girth all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

S&F 75mm dia PVC (SWR) bends all as specified and directed.

S&F 110 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

S&F 100 mm dia PVC (SWR) bends all as specified and directed.

M&L coloured double charged polished glazed vitrified tiles 10 mm thick (Square/rectangular) polished area of each tile exc 0.36 sqm but not exc 0.72 sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles all as specified and directed. Make : H R Johnson/ Nitco / Kajaria.

M&L coloured double charged digital glazed vitrified tiles 10 mm thick (Square/rectangular) polished area of each tile exc 0.36 sqm but not exc 0.72 sqm in vertical surfaces such as skirting & dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles all as specified and directed. Make : H R Johnson/ Nitco / Kajaria.

M&L Screed bed or bedding layer of mortar 15 mm thick in (1:6) for laying floor finishes like tiles all as specified and directed.

M&L coloured, digital glossy/Matt outdoor elevation ceramic tiles in vertical surface 600x300x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shades of the tiles including 10 mm thick rendering in CM 1:4 all as specified and directed. Make -Johnson/ Kajaria or equivalent)

M&L granite (of any approved colour) 18-20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform, flooring and all other similar works, including moulding/rounding the edges of stone, laying over & including 15 mm thick cement mortar (1:6) all as specified and directed.

M&L Glazed coloured tiles 600x300x8 mm thick on vertical surfaces of wall set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in CM (1:4) backing of wall tiles such as dado/skirting in vertical surface all as specified and as specified.

M&L Anti - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles including 15mm thick screed bed in CM 1:6 all as specified and directed .

M&L earth filling in floors, spreading and leveling in layers, well ramming including watering as required all as specified and directed.

M&L broken stone or boulders hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and directed.

M&L sand filling under floors or in foundations including watering and consolidation all as specified and directed.

M&L polythene film, black, 150 micron conforming to IS 1508 laid in floors all as specified and directed.

M&L 100 mm thick cement concrete 1:4:8 type D2 using 40mm graded crushed stone aggregate as in sub floors, sub bases, floors and pavings all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in floors, plinth protection (finished surfaces even and fair) laid in panels including joints filled with sealing compound grade 'A' all as directed by Engr-in-Charge

S&F 4mm thick panel of any type, pattern and shape Aluminium Composite Panel (ACP), aluminium thickness of 0.5mm, Front side finish of aluminum roll coated with Plain / coloured / wooden texture PE / PVDF, Core material of Non-toxic polyethylene, Macromolecular lamination film, Rear side of Aluminum coated with primer and including frame work using of Fasteners, including concealed screws, nuts, bolts and other items required for connecting aluminium to aluminium / steel / wooden / ply board, Blind rivets all fixing anchors, brackets and similar attachments used in the erections, shall be of aluminium, non-magnetic stainless steel, zinc coated steel, for fixing in both internal / external wall cladding complete weather proofing sealant of a polyurethane elastic joint / structural silicone sealant / pre-formed gaskets to the Horizontal & Vertical Joints in the Aluminium cladding / facade as per manufacturer's instructions all as specified and directed. Note : 1. The unit rate quoted is deemed to be inclusive of all necessary fixing acceserries mentioned in the description of work and scaffolding works at any height for installation. 2. For payment purpose panels areas will be measured on one side only.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts of required size, on the top of floor or the side of waist slab with suitable arrangemet for Stainless Steel grade 304 decorative designer railings, staircase, covers, sitting place, shed (design and pattern as approved) all as directed by Engineer-in-Charge. Make : Jindal stainless Ltd., SAIL, TISCO, POSCO etc.

S&F 12mm thick, toughened glass for door shutters, partitions in bathroom or other places, shelves, table top etc and in similar work with and including fitting and fixtures such as glass handles 600 mm long stainless steel studs, fittings for door pivots all as specified and directed .

S&F SS 304 Grade metal letters of height 300mm with PU paint to match the logo colors, mirror polish finish, anti rust including necesssary arrangements to fixing in walls, using scaffolding at any height all as specified and directed.

S&F designer stainless steel drawer handles, projection drop (50mm to 75 mm) on screwed plate all as specified & directed

S&F 1000 litre rotational moulded PVC tank 3 layer in position at any location on top of the building including removing existing tank disconnecting all incoming and out going connections, provision of new fittings including with float valve suitable up to 20 mm bore GI pipe all as per existing requirements all as specified and directed. Make :Sintex ,polycon , Plasto ,INfra

Dismantling mangalore pattern or similar tiles in roofing including portions bedded in cement mortar all as specified and directed.

Dismantling roof battens of any description in any position all as specified and directed.

Taking down chowkhats or frames area n exc 1.5 sq. m each with shutters (without taking off shutters from the frame) all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area exc 1.5 sqm to 4.0 n exc each all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section in any position unframed work all as specified and directed.

Dismantling of wall and ceiling boards( fibre pulp insulation etc) any thickness including cover fillets all as specifed and directed.

Taking down Chowkhats and shutters of windows/ventilators with wire mesh / glass and MS grills of any size including all fittings and fixtures all as specified and directed.

Demolition of brick masonary built in cement mortar all as specified and directed .

Demolition of cement concrete (unreinforced below or above ground level) n.exc 15cm thick and removing rubbish outside of MOD land 25 Km away from the site all as specified and directed

Dismantling of floor, hearth or wall tiling including cement mortar bedding but not backing and rubbish off the primises outside of MOD land 25 Km away from the site all as specified and directed.

Dismantling of CP fitting and santiary fitting and remove from the site all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid, bedded and pointed in any mortar and removal of rubbish off the site outside of MOD land 25 Km away from the site all as specified and directed.

Taking down cement plaster of any description from brick wall or concrete surfaces including racking out joints and hacking for key, scrubbing down with water all as specified and as directed

Taking up or down steel tubing 15 /20 mm dia and connection including cleaning for refixing or removing to store all as specified and directed

M&L 100 mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in flooring and or similar work all as specified and directed.

M&L coloured, digital, glazed ceramic tiles in vertical surface exc 0.36 sqm but not exc 0.64 sqm 9-10 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shades of the tiles including 10 mm thick rendering in CM 1:4 all as specified and directed. Note:- (Rate of Designer border in vertical surface will be deemed to be into quoted rates) Make : M/s H R Johnson/M/s Kajaria/M/s Somany Tiles Ltd

S&F 18 to19 mm thick HDHMR board, prelaminated one side with decorative choice lamination & other side high glossy acrylic sheet 3mm thick, exterior grade, fixed with screws to frame work as in cup borad & kitchen cabinet shutters and all other similar works all as specified and directed. Make:- Action tessa/Greenply/century ply as approved by GE.

S&F Partial overlay / fully overlay hydraulic soft closing concealed hinges having size 103mm x 64mm finish of nickel/silver all as specified and directed by Engg-in-charge. Make : Godrej/Hitech/Hafal Kitchen appliances.

S&F factory made 35 mm thick 2nd hard wood, plain framed panelled shutters (any panel) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS :1003(Part-I) kiln seasoned and chemically pressure treated all as specified and directed.

M&L for preparation of new wood or wood based surfaces, of any description, not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

S&F in repairs hot water extention pipe made out of copper chromium plated 450 mm long with brass adaptor and fixing in position all as specified and directed.

M&L french polishing on surfaces of any description, width or girth including cleaning and preparing the surfaces including a coat of wood filler on old surfaces with one or more coats all as specified and directed.

S&F in repair 12mm thick, toughened glass for door shutters, partitions in bathroom or other places, shelves, table top etc and in similar work with and including fitting and fixtures such as glass handles stainless steel studs, fittings for door pivots all as specified and directed .

Supply and fixing Sun control film, 50 micron non reflective type, sticked to glass as per manufacturers instructions and as directed.

S&F in repair stainless steel 202 Stain finish Handle D type, 25mm dia 600mm long for glass shutter all as specified and directed

S&F in repairs bottom/top patch fitting for pivot all as specified and directed

S&F in repairs bottom lock patch fitting all as specified and directed

M&L in repairs 8/10 mm thick PVC ceiling or wall panelling (any colour) with aluminium frame work for receiving ceiling board / wall panelling including all necessary accessories for fixing at various levels all as specified and directed.

M&L 10 mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface with GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 mm and 30mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre with & including Hangers 4mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long all as specified and directed.

Extra over above items no. 142 for any sunk or raised moulding all as specified and directed.

M&L SmartCare Damp proof in two component acrylic polymer-modified cementitious high performance coating SmartCare Damp Block 2K slurry by brush or roller over SSD masonry/brick surface Allow the 1st coat to dry for 4-6 hrs (drying depends on ambient temperature) and then apply 2nd coat. The 1st coat & 2nd coat must be applied in perpendicular direction for better results. The 1st coat & 2nd coat must be applied in perpendicular direction for better results. If the application is being done on bricks, overlay of cementitious screed within 24 to 48 hrs. For screeding use SmartCare Vitalia as an integral waterproofing compound. It is essential to cure SmartCare Damp Block 2K/overlay screed for a minimum of 3 to 5 days to ensure full cement hydrationall as specified and directed. Make DR Fixit (Sure seal)/Asia Paints (Smart care Damp Block 2K)

M&L Hard drawn steel welded wire fabric mesh,100 x 100 x 3mm dia, cut to lengths bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm dia supplied anchored over 3 to 4 inch long iron nails at a distance of 0.6 m in both direction and fixed in walls / reinforcemnt weight not less than 1.37 Kg/Sqm but not exc 4kg per sqm for fixing and for bracing, supporting or otherwise holding firmly in position so that the placing and ramming of concrete will not displace it. The rates include for straightening, raking or circular cutting and waste. Rates also include for straightening where reinforcement is supplied in rolls/coil all as specified and directed.

Clean the existing reinforcement with wire brush/ rotary wire brush to make surface free from rust scales, loose material, dirt and providing, applying two coats of alkaline rust converting primer confirming to ASTMB- 117, on the existing rebars and allowing it to react with rust for 6 hrs and form a corrosion resistant, insoluble and adherent protective layer, including cleaning the reinforcement, wire brushing to remove loose rust spalls, with time interval of 1hour between the coats all as specified and directed. Name of Manufacturer: BASF/Fosroc/Sika/ Dr Fixit

Providing and application of full and unbroken coating of anticorrosive protective zinc rich epoxy coating on expose reinforcement in two coats with time interval of minimum 1 hours between each coat including mixing of both componants by weight as per mfg specifications, brush application, curing to form a anticorrosive protective coating with high mechanical strength to cementitious repair works all as specified and directed. Name of Manufacturer: BASF/Fosroc/Sika/ Dr Fixit

Rebuilding the section of damaged RCC elements to its original size or as per consultants recommandations in thicknesses of 40-100 mm by providing and casting with micro-concrete of grade M-40 and above including providing and fixing of water tight foam faced finish shuttering of minimun 18 mm thick with supporting framework, all lead lift, mixing, placing, de-shuttering, levelling the surface by grinding off cementitious slurry or construction joint differences if any to satisfaction of engineer- in-charge, curing etc. complete.(Rate includes cube test to be conducted for every 5 M.T of workdone. Six no's of sample required per test). Ensure the quality of water by testing water as per IS 456 and document the same. Ensure temperature at the time of mixing should be between 25 to 40 degree celcius by electronic temperature gauge all as specified and directed. Name of Manufacturer: BASF/Fosroc/Sika/ Dr Fixit

M&L for filling cracks by cutting 'V' groove cracks of internal or external plaster of walls, ceilings/Chajjas all along the crack upto 10 mm and remove the loose plaster/concrete by suitable tools, filling cracks with crack paste compound and apply the second coat after 10-12 hrs of application of first coat and for external application must be coated with paint including necessary scafolding of any height all as specifed and direcetd. Make : Use of Dr Fixit Crack 'X' shrinkfree paste compound/ Smartcare Texture Crack Filler / Build Core Compound / Fosroc Compound, as approved by GE

M&L for cleaning all loose laitance on the wall and concrete substrate and applying one coat of epoxy bonding agent of SBR latex on exposed concrete surface to ensure bond between old concrete & new concrete by brush application including scafolding at any height as specified and directed. Make: Dr. Fixit epoxy bonding agent or Shalicrete URP of STP Ltd or Nerolac perma SBR latex

M&L plastering 20 mm thick average Polymer modified mortar (ready mix pack) in two coat 15 mm base coat and 5 mm finishing coat with and including curing as per manufacturer's instruction all as specified and as directed. Make : Dr. Fixit RepairPro Polymer Mortar, Fosroc RENDEROC S2 structural grade polymer mortar, ShaliFix FRM Polymer Modified Fiber Reinforced Mortar of STP or equivalent as approved by GE

M&L in repairs for any coloured vitrified heavy duty outdoor anti, skid full, bull -noise finish, self embossed grooves body tiles 10 mm thick (Square/rectangular, 600mm x 600mm) polished area of each tile exc 0.09 Sqm and not exc 0.36 sqm, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles including 20 mm thick in cement plaster in CM (1:4) for fixing tiles anywhere all as specified and directed. Make -Somany/Rak/Kajaria(Grandstone Crema series) or equivalent

M&L in repair to replace old decayed timber (including piecing, scarifying of old and new timber if required) second class hard wood clean sawn in scantlings timber framed and fixed in any position and description including scafoldings of any height all as specified and directed.

S&F in repairs to replace old or decayed boarding in patches including cutting out old, piecing, heading joints 20 mm thick second class hardwood clean sawn boarding fixed with nails with butt joints in any situation including scafoldings of any height all as specified and directed.

M&L reinforced cement concrete pipe of 150 mm dia class NP-2 laid and joined and tested with collers all as specified and directed.

M&L concrete bed to drain pipe 150 mm dia including packing under and completely surrounding pipes with concrete after they are laid and tested in PCC 1:4:8 type D 2 (using 40mm graded crushed stone aggregate) all as specified and directed.

Cutting into existing man holes for connecting new drains making good to pipes and rendering cutting out existing benching for and forming branch channel (1/2 round or ¾ in section) in cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) surface smooth finished and reforming benching as required for internal dia of pipe 150mm all as specified and directed .

M&L PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in coping, benching, even and smooth without using extra cement all as specified and directed.

M&L pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar, PCC 1:3:6 (type C1) 10cm thick (with plain or interlocking joints as directed) setting in mortar 1:4, all as specified and directed.

Extra for forming fair finished to drain or channel 30 cm inner girth in cement including forms, mould mitred/stopped ends etc.

M&L rubber moulded glossy finished 60 mm thickness precast grass concrete interlocking paver block of any shape and size confirming to IS 15658 -2006 of, M-35 Grade with grey cement and pigment laid over sand cushning including compaction of paver blocks using surface vibrator including 30 mm thick compacted bed of coarse sand, filling the joints with fine sand including providing grass on surface all as specified and directed.

M&L rubber moulded glossy finished 60 mm thickness precast concrete interlocking paver block of any shape and size confirming to IS 15658 -2006 of, M-35 Grade with grey cement and pigment laid over sand cushning including compaction of paver blocks using surface vibrator including 25 mm thick compacted bed of coarse sand, filling the joints with fine sand as per the direction of Engineer-in-charge.

M&L RCC 1:2:4 type B-1 (Nominal mix ) (using 20mm graded crushed stone aggregate) as infactory made precast cover slab perforated fixed in position, tie between two brick walls and all other similar works set in CM 1:4 including necessary form work all as specified and directed.

Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings are to be measured separately) and/or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling all as specified and directed.

Taking down carefully copper/aluminum submain wiring complete including all fixtures such as switches, pendant, lamp holder, regulators, switch socket outlet, bulk head fittings, tube light fittings and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces all as specified and directed

M&L Point wiring with 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH, 1100 volts grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, concealed with accessories and incuding provision of 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box and cover plate of suitable size with suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139 (pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches, socket outlets, etc. with brass screws and brass washers and making good the disturbed surfaces with applying two coats of paint of colour as per directed by engineer incharge as per existing for one light point controlled by one switch. Note :- Switch, socket and fan regulators to be measured and paid for separately . Make of Wire: Havells/ Polycab/ Finolex. Note : Rate quoted is including providing the blank plate to modular plate whereever necessary.

All as per srl item No 166 here-in-before but for one socket point 15 Amp with 2.5 sq mm PVC unseathed FRLSH wire along with 2.5 sq mm green colour wire as earth contuinity conductor connected to common earth dolly all as specified & as directed.

All as per serial item No 166 above but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) all as specified and directed.

All as per serial No. 166 here-in but for Bell Point controlled by one bell push.

All as per serial No. 166 here-in but for Exhaust fan controlled by one switch.

All as per serial no. 166 here-in but for One cealing fan controlled by one switch.

Description all as per Srl item No. 166 here in before but for socket outlet point 5 Amp on same board.

All as per Srl item No.166 here in before but for socket outlet point 5 Amp on Independent board.

S&F modular switch 1 way 6 A, module 230/250 volt , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. Make : Havells Reo, Anchor Roma, Legrand.

Supply and fixing modular switch 1 way 16 A, module 230/250 volt, AC supply, ISI Marked, with white cover plate with frame all as specified and directed. Make:- Havells Reo, Anchor Roma, Legrand.

S&F modular bell push 1 way 6 A module 230/250 volt, AC supply, ISI Marked, with cover plate complete all as specified and directed. Make : Havells Reo, Anchor Roma, Legrand.

S&F modular socket, 6A, 2/3 pin combined 2 module 230/250 Volts, 50 Hz, AC supply, ISI Marked, with cover plate all as specified and directed. Make: Havells Reo, Anchor Roma, Legrand.

S&F modular sockets 6A/16A, 2/3 pin combined 2 module 230/250 Volts, 50 Hz, AC supply, ISI Marked, with white cover plate with frame all as specified and directed. Make : Havells Reo, Anchor Roma, Legrand.

S&F Buzzer, Ding Dong AC, 230 volts, single pole all as specified and directed.

S&F moduler stepped type electronic fan regulator 120 watt flush type, two module all as specified and directed. Make: Havells Reo, Anchor Roma, Legrand.

S&F switch piano (ISI marked) Single pole 240 volts, 5 Amps all as specified and directed. Make- Havells/anchor/ Legrand.

S&F socket (ISI marked) 2/3 pin and 5 Amps, flush type, 240 volts all as specified and as directed. Make- Havells/anchor/ Legrand.

S&F ceiling rose surface bakelite 65x50mm, 3 terminal all as specified and directed. Make: Cona , Plaza, Anchor .

S&F in repairs 20 watt LED, 6500 K, 4 feet long fixed including on PVC square for mounting the fittings and electrically connecting with three single core 23/0.0076. PVC insulated multi strandard copper flexible cable from ceiling rose to light fitting (connector block of lamp fitting) and one for earthing all as specified and directed Make:- Wipro, Model No : Wipro Garnet 20W LED Batten 6500K.

S&F in repairs 10 watt LED, 6500 K, 2 feet long fixed including on PVC square for mounting the fittings and electrically connecting with three single core 23/0.0076. PVC insulated multi strandard copper flexible cable from ceiling rose to light fitting (connector block of lamp fitting) and one for earthing all as specified and directed. Make:- Wipro, Model No : Wipro Garnet 10W LED Batten 6500K.

S&F LED luminaire 2 feet x 2 feet, 40 watt/ 6500K, 220 V, AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size all as specified and directed. Make Wipro/ Bajaj/ Havells.

S&F LED security Building light LED 35/45 Watt, pressure die cast aluminum housing, heat resistant glass, IP65 protection, better optics for uniform distribtion with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light all as specified and directed. Make:- Bajaj Cat part No- 169821 LED/CG as perr vat No LSTO 25 CDL equivalent model as in Surya / havells .

S&F exhaust fan 230 volts, 250 mm, sturdy engineering plastic body with wooden frame including making all electric connection all as specified and as directed including cutting of hole on wall and makng good disturbed surface of wall and outer wooden box for fan fix on wall all as specified and directed. Make Bajaj/ Havells/ Crompton Greaves.

S&F ceiling fans with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as specified and directed. Make : Bajaj or equivalent make of Havells/ Crompton Greaves.

M&L for refixing of ceiling fan (old fan) and connecting up including provision of cable from ceiling rose or connector and fan painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust with taking down fan, sealing cable end, dismantling romoving and hanging fan with rod of required length and proper hook and blades and removing fan and blades to store all as specified and directed. Note: Connection should be made neatly using two core flexible cable.

S&F in repairs MCB Distribution board , 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 100 Amps rated bus bar with neutral link, 8 ways, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection all as specified and directed. Make: Havells Cat part No DHDPSHODRW12 or equivalent in Schnieder/GE/C&S.

S&F in repairs MCB Distribution board, 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 12 ways, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection all as specified and directed. Make: Havells Cat part No DHDPSHODRW12 or equivalent in Schnieder/GE/C&S.

S&F in repairs MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series all as specified and directed.

S&F in repairs MCB, single pole 240 volts 6 to 32 Amps capacity fixed in DB's all as specified and directed.

S&F in repairs MCCB DB TPN 4 way vertical sheet metal enclosure TPN 415 volts, 50 Hz, with IP-43 protection, single door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting all as specified and directed. Note: MCB SP/TPN shall be measured and paid seperately under appropriate items of this schedule . Note : Copper thimble shall be used for connection of cable .

S&F in repairs MCCB TPN, 240 Volts, 63 to 100 Amps, 10 kA rupturing capacity 415 Volts all as specified and directed.

M&L in repairs Sub main wiring with two run of single core 1.5 Sqmm FRLSH copper three core conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia in Conduit ISI marked with all accessories such as Tees, elbows, junction boxes as required fixed on wall alongwith one run of 1 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board/distribution board and testing on completion all as specified and directed. Note: (i) Two runs of 1.5 sqmm and one run of 1 sqmm cable and one run of PVC conduit shall be measured as one RM length.

Material & Labour for Sub main wiring in repair, with two run of 6 sq mm stranded copper conductor PVC unseathed FRLSH wire along with 6 sq mm green colour wire as earth contuinity conductor connected to common earth dolly including PVC FR heavy duty conduite of adequate size (not less than 32 mm dia) for housing the wires for from Pannel / Main DB to house SPN DB including taking down old Unsv submain with all associated fixtures complete all as specified & as directed by engr-in-charge Make : Finecab / Havells / Finolex as approved by GE Note: Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. Note: Mode of measurement two runs of 6 sqmm cable and one run of 6 sqmm cable with PVC conduite shall be measured as one length.

M&L in repairs Sub main wiring with two runs of single core 4 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia concealed ISI marked with all accessories such as Tees, elbows, junction boxes as required fixed on wall alongwith one run of 4 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board/distribution board and testing on completion all as specified and directed. Note: (i) Two runs of 4 sqmm and one run of 4 sqmm cable and one run of PVC conduit shall be measured as one RM length.

Supply, lay in trenches, floors ,fix on wall/pole, passing through pipes LT UG cable, 1100 volts grade, PVC/ XLPE insulated, with multistranded aluminium conductors, armoured with galvanised steel wire or tape, gland, lugs of size 10 Sq.mm 3core, confirming to IS specifications all as specified and directed. Make: Plaza/ Polycab/ Finolex

Supply, lay in trenches, floors, fix on wall/pole, passing through pipes LT UG cable, 1100 volts grade, PVC/ XLPE insulated, with multistranded aluminium conductors, armoured with galvanised steel wire or tape, gland, lugs of size 35 Sq.mm 3.5 core, confirming to IS specifications all as specified and directed. Make: Plaza/ Polycab/ Finolex

M&L for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth not less than 2.25 m deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level and connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers, galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil including necessary testing on completion all as shown in Electrical Plate No 3 of SSR part -I. Note : On testing resistance of earthing should be less than 2 Ohm.

Unitech Enterprises

Bidder Name

Unitech Enterprises

Colaba Group Works