SPECIAL REPAIR TO BLDG NO.T-31 OF 825 ASC BN AM SA JOB NO. 41SA SR BLDG 14 2024-25 AND PROVISION OF TOILET IN 825 ASC BN AM AT ROWRIAH IN JORHAT JOB NO. 41SA RW 23 2024-25 MIL STATION UNDER GE JORHAT

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level), complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles and depositing off the rubbish materials where directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4.0 Sqm each, complete all as directed.

Taking down shutters of any description not exc. 1.0 sqm each, complete all as directed.

Taking down shutters of any description exc 1.0 sqm and not exc. 2.0 sqm each, complete all as directed.

Dismantling timber scantlings 40 sq. cm and over in section unframed, in any position, complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing, complete all as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out, complete all as specified and directed.

Excavation in trenches, not exc. 1.5 m wide and not exc. 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying pipe, cable, etc. n exc 10 sqm on plan and not exc. 1.5 m in depth and getting out in soft/ loose soil, complete all as specified and directed.

Returning filling in soft/ loose soil, including spreading, levelling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level not exc. 1.5 m above the starting point, complete all as specified and directed.

Material and labour for, hardcore of gauge not exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

Material and labour for, RCC (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed.

Material and labour for, RCC (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in as in columns, pillars, piers, posts and struts, complete all as specified and directed.

Material and labour for, RCC (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed.

Material and labour for, brickwork with subclass ‘B’ bricks, old size, straight or curved on plan exc. 6m mean radius built in cement mortar (1:6), complete all as specified and directed.

Material and labour for, brickwork with sub class ‘B’ bricks, old size brick, straight or curved on plan to any radius in half brick thick walls built in CM (1:4), complete all as specified and directed.

Material and labour for, 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including taking down old existing, complete all as specified and directed.

Material and labour for, 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

Material and labour for, use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams, etc., rough finished surfaces of concrete, complete all as specified and directed.

Supply and fix for solid PVC sinle door frame of size 50mm x 95mm made out of 5mm plain colour PVC sheet reinforced with M.S. tube, complete as per specification & drawing and directed.

Supply and fix for, factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, complete all as specification and drawing.

Supply and fix for, 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 200mm long, complete all as specified and directed.

Supply and fix for, extruded aluminium alloy handles, fabricated type, anodised 150mm size, complete all as specified and directed.

Supply and fix for, 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

Supply and fix for, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and fix for, aluminium door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed

Supply and fix for Harrison rails, mild steel, chromium plated curtain rail with fixing brackets, stops, rollers etc., complete all as specified and directed

Supply and fix for, mild steel flat iron 25 x 3mm as in band, straps, hold fasts etc. and similar small articles conforming to Fe-410-0 or Fe-310-0, complete all as specified and directed. Note: The hold fast shall be treated in two coats of tar and the cost for the same is deemed to be included in unit quoted rate.

Supply and fix for, mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Supply and fix for, rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed.

Material and labour for, mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Material and labour for, mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Supply and fix for, anodised aluminium frame powder coating (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Supply and fix for, anodised aluminium powder coated (minimum thickness of powder coating 50 micron) for windows and ventilators shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beasding, screws etc. complete all as specified and directed.

Supply and fix for, anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fix for, 12mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and directed.

Material and labour for, powder coated GI exposed snap grid frame work for false ceiling, size of grid 605 x 605mm, including GI main tee section of size 35mm x 25mm x 0.7mm (minimum), GI cross tee of size 35mm x 25mm x 0.7mm (minimum) and GI wall angle of size 25mm x 25mm x 0.7mm (minimum), suspended from soffit at approx 900mm cetnre to centre with GI cleat and steel expansion fasteners with and including level clip and 6mm dia GI wire hanging arrangement with adjuster all as specified in clause No.10.38 in SSR Part-I and incuding 4mm thick high pressure steam cured non asbestos fibre cement reinforced multipurpose board as per IS 14862 including taking down existing false ceiling system, complete all as specified and directed.

Material and labour for, powder coated aluminium snap grid frame work for false ceiling, size of grid 605 x 605mm, including aluminium main / cross tee section of size 35mm x 23mm x 1.5mm (minimum) and aluminium angle 25mm x 23mm x 1.5mm thick, suitable size GI wire hanging arrangement with adjuster all as specified in clause No.10.38 in SSR Part-I and incuding 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over metal frame work including taking down existing false ceiling system, complete all as specified and directed.

Material and labour for, 100mm thick plain cement concrete (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in sub base floor, complete all as specified and directed.

Material and labour for, 75mm thick plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in plinth protection, finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.11 Sqm but not exc.0.18 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6), complete all as specified and directed.

Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.11 Sqm but not exc.0.18 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6) including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Materials and labour for, glazed ceramic coloured tiles,350 X 250 X 7mm/ 450 X 350 X 7mm thick, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat of cement mortar (1:4), complete all as specified and directed.

Material and labour for, rendering 10 mm thick, cement plaster, in cement mortar (1:6) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:6) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed. (Note: Water proofing compound shall be measured and paid seperately under relevant item).

Supply only integral water proofing compound complete all as specified.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of acrylic emulsion distemper over a coat primer, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of acrylic emulsion distemper over a coat primer over 1mm thick wall care putty, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat primer, complete all as specified and directed.

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth, complete all as specified and directed.

Supply and fix for 4.0mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and directed.

Supply and fix for, 4.0 figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sq. m in each pane, complete all as specified and directed.

Supply and fix for, 5.5mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Supply and fix for 15mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for 20mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for, bib tap, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and directed.

Supply and fix, pillar taps, fancy type, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

Supply and fix for, stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix for, angle valves, fancy type, chromium plated, cast copper alloy with long shank and cup concealed type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix for, vitreous china wash basin, white, flat back, size 550 x 400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, 32mm dia corrugated PVC waste pipe, chromium plated coupling 32mm dia and cutting for and pinning in ends of brackets or erecting stand, complete all as specified and directed.

Supply and fix for, vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), connection to trap and to flushing cistern anti syphonage pipe including provision of PCC or lime concrete bedding and removal of debris, complete all as specified and directed.

Supply and fix for, vitreous china urinal partition white of size 310x700 mm, complete all as specified and directed.

Supply and fix for, PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

Supply and fix for cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

Supply, hoisting and fixing in position of rotational moulded polyethylene water storage tanks double layers (cylindrical vertical with closed top) of 1000 litres capacity with ISI marked and all as specified in IS12701 including 20mm bore dia ball valves high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed (Minimum weight 20 mm - 210 gms) and taking down existing water tank, complete all as specified in SSR Part I and directed.

Cutting into existing manholes for connecting new drains, 100mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts, bolts etc., complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) bends any radius with access door, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed.

Supply and fix for, soap dish, vitreous China white, approximate size 160x 160x90mm, complete all as specified and directed.

Material and labour for, cutting CI/ GI/ DI water supply line with the help of electric cutting tools or manually, reducing to required length before laying and blockage removal, cleaning of particular joint etc. and making good after repairing of size upto 100mm dia including leakage testing, complete all as directed.

All as per serial item No.86.00 here-in-before but in position for insertion of new Tees of 100mm x 100mm x 25mm, branches and saddle pieces with connected accessories including necessary earth work.

Supply and fix for 25mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for, 25mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

Taking down carefully unservoceable copper/ aluminium point wiring (light, fan, bell, socket or power) including all fittings such as switches, ceiling roses, regulators, sockets, switch boxes etc. complete and making good the disturbed surfaces complete all as directed.

Material and labour for, point wiring with PVC insulated unsheathed stranded FRLSh copper conductor cable 1100 volts grade, ISI 694 marked of size 1.5 Sqmm drawn in and including PVC rigid conduit (heavy duty, ISI marked) not less than 20mm dia with all necessary fittings such as bends, cross, elbow, tees etc. with MS pressed steel cadmium plated terminal box not less than 1.6mm thick for mounting switches, sockets, fan regulator etc. and 3mm thick laminated sheet top cover (ISI marked) including 1.5 Sqmm PVC insulated unsheathed stranded FRLSh copper conductor as continuous earth wire and connected to common earth dolly for one light/ ceiling fan/ exhaust fan controlled by one, one way switch, complete all as specified and directed.

All as per serial item No.92.00 here-in-before for one 5 pin 5 Amps switch socket outlet point on independent board.

Material and labour for, point wiring with PVC insulated unsheathed stranded FRLSh copper conductor cable of size 1.5 Sqmm in and including PVC rigid concealed conduit (heavy duty) of required dia with all necessary fittings and necessary cutting/ chasing etc and making good the disturbed surfaces, including 1.5 Sqmm PVC insulated unsheathed stranded FRLSh copper conductor as earth lead and connected to common earth dolly for one light/ ceiling fan/ exhaust fan controlled by one, one way modular switch, complete all as specified and directed.

All as per serial item No.93.00 here-in-before for one 5 pin 6 Amps modular socket outlet on independent board.

All as per serial item No.93.00 here-in-before for one 5 Amps modular socket outlet on same board with other modular switch.

Material and labour for, point wiring with PVC insulated unsheathed stranded FRLSh copper conductor cable of size 4.0 Sqmm in and including PVC rigid concealed conduit (heavy duty) of required dia with all necessary fittings and necessary cutting/ chasing etc and making good the disturbed surfaces, including 4.0 Sqmm PVC insulated unsheathed stranded FRLSh copper conductor as earth lead and connected to common earth dolly for one modular socket outlet 5 pin 15/ 16 amps on independent board, complete all as specified and directed. Notes for item Nos 93 to 96: Flush steel terminal box, inner plate and front plates shall be measured and paid sepertely under relevant item.

Supply and fix for, modular metal flush box 1/2 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 3 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 6 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 8 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame (both inner and outer plate cover), 2 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame (both inner and outer plate cover), 3 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame (both inner and outer plate cover), 6 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame (both inner and outer plate cover), 8 module, complete all as specified and directed.

Supply and fix for, modular socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for, modular socket 6A/16A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 6A, 1 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 16A, 1 module, complete all as specified and directed.

Supply and fix for, fan step regulator, 120W - 2 module, complete all as specified and directed.

Supply and fix for, switch piano, flush type single pole, one way 5/ 6 Amp, complete all as specified and directed.

Supply and fix for, switch socket combination 5 in 1, 5/6 Amps, flush type, complete all as specified and directed.

Supply and fix for, ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body, complete all as specified and directed.

Supply and fix for, exhaust fan, steel body AC single Phase 230V of size 300mm sweep with, blades, frame and louvers including necessary hole for insertion of exhaust fan, complete all as specified and directed. Note: (i) The item is inclusive of making holes or making existing opening suitable for the installation of exhaust fan as per site condition (ii) Louvers for the exhaust fan shall be made of GI sheet, suitably and properly fixed to the opening.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, SPN 240 volts, 4 ways 200 Amps rated bus bar, metal double door type IP-43, complete all as specified and directed.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, SPN 240 volts, 8 ways 200 Amps rated bus bar, metal double door type IP-43, complete all as specified and directed.

Supply, fixing, testing and commissioning for, 6 to 32 Amp, SP 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply, fixing, testing and commissioning for, 32 Amp, SPN 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply and fix for single pole and neutral enclosure with a two pin and earth plug and socketcomplete with one single pole MCB 20 Amps, complete all as specified and directed.

Supply and fix for, sub main wiring with two runs of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including 20mm dia rigid PVC conduit, (heavy duty) (ISI marked) surface type with all accessories such as junction boxs, bends, tees etc. including one run of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire including taking down old unserviceable submain wiring, complete all as specified and directed. Notes: All runs of copper conductor and one run of conduit shall be measured as one unit length.

Supply and fix for, sub main wiring with two runs of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including 20mm size PVC casing and capping, medium grade (ISI marked) surface type with all accessories such as junction boxs, bends, tees etc. including one run of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire including taking down old unserviceable submain wiring, complete all as specified and directed. Notes: All runs of copper conductor and one run of casing and capping shall be measured as one unit length.

Supply and fix for, LED tube light fitting 1 x 20W (+/-5%) 220 volt, AC with extruded strip in thermally conductive material and extruded housing in optically efficient material milky white with system lumen efficacy> 120 lumen per watt minimum system 2300 - 2400 and make LED of chip: Osram, Cree, Nichia, Seoul, Sumsung. Integrated electronic driver, SMD based LED constant current supply with double sided connection to avoid short circuit and surge protection greater than 2.5 KV, IP 20 protection and CRI>80, power factor> 0.95, THD less than 15%, correlated colour temperature (CCT) of 6500K, operating voltage of 140 to 270 volt, frequency of 50Hz, burning hours 50000 hours with comprises of CRCA pre-coated metal housing all as per Cat No.CG-CCS-100-20-65-HL2-DP-NWH of make Crompton or equivalent model of make as specified in PS, complete all as specified and directed.

Supply and fix, LED street light fitting 35 Watt 230 Volt AC outdoor type made of pressure die cast aluminium housing with toughened glass cover, IP66 protection, high power LEDs with secondary lenses and system efficay should be minimum 110 lumen per watt and LM79 all as per Cat No.CG-TRP-400-35-57-SL-LM-NSR of make Crompton or equivalent model of make as specified in PS, report should be provided from NABL accredited lab. Driver should be BIS approved silicon filled potted driver with inbuilt 4KV surge protection and external 10KV surge protection inside luminaire housing for trouble free service life. THD shall be <10%, power factor>0.95, CCT5700K and Brand name should be embossed/ engrave on the LED fitting traceability till life. Warranty should be 2 years and warranty certificate should be provided on OEM letterhead at the time of delivery, complete all as specified and directed.

Supply and fix for, LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size, complete all as specified and directed.

Supply and fix for, street light bracket, fabricated out of 40mm bore GI tubing light grade, 1.5m length bend to the shape, mounting with MS clamp of flat iron size 40 x 5mm of suitable length 2 pairs including nut and bolts etc suitable size, complete all as specified and directed.

Material and labour for, earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.50 metre below normal ground level connected to galvanised steel earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete earth pit in PCC (1:3:6) type C1, 50mm thick pre-cast RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) cover slab (Reinforced with 8mm dia TMT bar @15cm centre to centre bothways and suitable handle made of 10mm dia), provision of funnel, wire mesh, 20mm bore galvanised steel tubing (medium grade) for watering, charcoal or coke and salt in alternate layers of 15cm (compacted thickness), 15mm bore galvanised steel tubing (light grade) for protection of earth lead connection, necessary excavation and earth work in any type of soil complete all as specified and indicated on electrical plate No.3 of SSR Part-I (2009) including testing on completion. (Note: GI earth wire and protection pipe upto 7.5metres shall be deemed to be included in the unit quoted rate).

Supply, laying, testing and commissioning of XLPE insulated, screened, PVC badded, galvanised steel strip or wire, armoured heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, cross-sectional area 10 sqmm 2 core, complete all as specified and directed.

Supply, laying, testing and commissioning of XLPE insulated, screened, PVC badded, galvanised steel strip or wire, armoured heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, cross-sectional area 35 sqmm 3.5 core, complete all as specified and directed.

Material and labour for, sand cushioning (dry) in trenches for protection of UG cables (below, above and around the UG cable laid in trenches) of 230mm spread thickness and consolidated (punned) upto 180mm thickness, complete all as specified and directed. (NOTE : For the purpose of payment, punned thickness of sand cushioning only shall be measured and paid for).

Material and labour for, sub class 'B' brick, well burnt, old size, flat, laid breadth-wise along the axis of cable laid in trenches over sand cushion laid for UG cable protection, complete all as specified and directed.

Supply and fix for, GI tubing 40mm bore, light grade, laid in trenches for cable protection under the road/ path/ pole, complete all as specified and directed.

Material and labour for 25mm dia high density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 for passing of cable through PCC foundation from trenches to cable junction box, complete all as specified and directed.

Labour only for manual horizontal boring under a depth of 0.65m for passing of GI cable protection pipe upto 50mm bore dia, under road/ foot path not exc. 6.00m in a single length, complete all as directed.

M/S PAUL CONSTRUCTION (BID ID -3296638)