Upgradation of Pitchavaram as a Major Tourist Destination, including various facilities at Cuddalore District

Amount

Pile Works-Mobilisation of pile rig including transportation, installation, driving of vertical cast in situ bored piles of following diameter using reinforced cement concrete Design Mix M25 Grade by setting the bored cast in situ pile., boring for the piles from ground level in all soils to the required depth below cut off level to carry a safe working load not less than specified, by Direct Mud Circulation Method ( using bentonite clay of required density) inclusive of pile accessories, temporary casing pipe, bentonite solution of 10% of concrete with required density and routine test as per IS 2911 (Part- IV) - 2013 etc. complete as directed by the departmental officers. Design Mix M25 Grade concrete using with ordinary Portland Cement with water cement ratio not exceeding 0.5 including the use of Plasticizer of required Grade and Hard Broken Granite Stone Jelly of 20mm size and down graded as per requirement. Mix Design Data has to be got approved by the departmental officers before commencement of work. The minimum cement content should not be lesser than 400 kg per cum. The rate shall include necessary pile chipping to the required depth and finishing the top of the pile neatly etc complete in all respects. Likewise, incase of pile growing if found necessitated during execution the same should be done to the required depth including developing the reinforcement also simultaneously to the required length and lap all as directed by the departmental officers. (Pile shall be measured from the founding level to the bottom of the pile cap.) Rate excluding cost of reinforcement which measured and paid under relavent item.

450mm dia

600mm dia

Supply and conducting Vertical load testing of piles in accordance with as per IS 2911 (Part- IV) - 2013 etc including supply and installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: After testing and unloading of the superimposed load splaced for the test, the pile should be chipped off 1metre below the ground level.

Initial Load Test-450mm dia 250MT

Initial Load Test-600mm dia 250MT

Routine Load Test-450mm dia 100MT

Routine Load Test-600mm dia 100MT

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. Rate to include backfilling, leveling, dressing of sides and ramming of bottom with all leads, lifts and filling inside the building plinth level including necessary compaction in layers of 150mm thick each complete as directed by the departmental officers. Note: The cost of earth work excavation shall be calculated based on the classifications of soils furnished in the trial pit details appended with the estimates For 0 to 2m depth.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. Rate to include backfilling, leveling, dressing of sides and ramming of bottom with all leads, lifts and filling inside the building plinth level including necessary compaction in layers of 150mm thick each complete as directed by the departmental officers. Note: The cost of earth work excavation shall be calculated based on the classifications of soils furnished in the trial pit details appended with the estimates For 2 to 3m depth.

Supplying and filling in foundation, basement, etc with following Manufactured sand brought from outside filling materials in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with following Good Earth brought from outside materials in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Providing Pre - construction Anti - termite treatment and creating a chemical barrier to the building by injecting chemical emulsion of required concentration under grade slab and grade beam and below the ground level as well as outside all-round the building at plinth level etc as per the instructions of manufacturer and as directed by the Client / departmental officers. The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS 6313 or equivalent BS specification. The chemical to be used as insecticide for the treatment shall be Biflex Tc and the application shall be diluted 1 part of chemical Biflex Tc with 49 parts of water to get 0.05% emulsion and strictly in accordance with the manufacturer’s specification. The work should be carried out by an approved and registered specialist pest control agency only. Tenderer to furnish the name of the proposed specialist firm. A 10 years post application guarantee against defects shall be furnished by the main Contractor. Note : Horizontal plan area at ground floor level of the building will be measured and paid. The chemical to be used for the treatment and concentration of the chemical solutions should be as laid down in IS - 6313 Part II.as complete with all respects complying with relevant standard specification, as directed by the Client / departmental officers.

Cement Concrete 1:4:8 (One Cement, Four Manufactured sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Cement Concrete 1:3:6 (One Cement, three Manufactured sand and six hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) Cost of MS sheet and angles for each set weight of MS sheet BG 10 of size 90cm x 60cm x 3.175mm 3.175 x 7850/1000 = 24.92 Kg 24.92 Kg x 0.54 Sq.Mt = 13.46 Kg Weight of MS angle of size 25mm x 25cm x 3mm 3.6 x 1.1Kg/Mt = 4.00 Kg.

Reinforced cement concrete Column footing, plinth / grade beam, bed blocks, template surfaces, steps, piers, pile cap, raft slab / beams and such other members

Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slab / beams and such other members

For plane surfaces such as rectangular, square columns and chamfered sunshades, top and bottom slab of boxing, kitchen platform, loft and such other structural members

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.0 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

REINFORCED CEMENT CONCRETE - DESIGN MIX CONCRETE - NOTE: RMC SHALL BE PROCURED FROM SITE BATCHING PLANT -Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

Ground Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in following Cement Mortar using best quality of Wire cut Bricks 9" x 4" x 2" in Cement Mortar 1:5 (One Cement and Three Manufactured Sand) for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

For foundation & basement

Ground Floor

Brick work in following Cement Mortar using best quality of Second Class Ground Moulded Chamber Burnt Bricks 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:5 (One Cement and Three Manufactured Sand) for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

For foundation & basement

Ground Floor

Brick partition walls of 11.50cm thickness using best quality II Class Ground Moulded Chamber Burnt Bricks of size 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three Manufactured Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (including Hoop iron reinforcement) in ground floor

Supplying and fixing Teak Wood Frames for Doors, Windows, Ventilators and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc complete in all floors. Teak Wood Scantling upto 2m length

Supplying and fixing Teak Wood Frames for Doors, Windows, Ventilators and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc complete in all floors. Teak Wood Scantling over 2.0m and below 3.0m in Length

Supplying and fixing of 200mm length mild steel hold fasts horizontally twisted with pair of suitable iron screwsetc complete in all respects complying with relevant standard specification and as directed by the Departmental officers.

Providing and fixing Solid core flush shutters with Teak ply on both side with teak wood lipping alround 35 mm thick. The shutter shall be made of solid core of block board type bonded with PF synthetic resin conforming to BWP grade of IS 848 with 6mm thick teak wood lipping as per drawing. The construction procedure of the shutter should be as per IS 2202. The shutter shall be shop prepared for taking mortice lock or latches suitable lock block of wood may be provided for fixing the hardware. The size of block, shall perfectly correspond to the maximum size of lock, covered in IS 2209. All the four edges of the door shutter shall be square. The shutter shall be free from twist or warp in its plane and of required size etc. complete as directed. Rate shall include for cost of hardwares (aluminium hinges 125x30mm size - 3Nos. aluminium aldrop of size - 250x16 mm - 1No. Aluminium tower bolt of size 250x12mm - 1Nos. tower bolt of size 200x12mm - 1No, D type aluminium handle of size 200mm-2No., aluminium door stopper with nylon bush - 1No) as required and fixing them all like lock, hinges, handle, tower bolts, and other accesories etc..as complete with all respects complying with relevant standard specification, as directed by the Departmental officers.

Supply and fixing of FRP door Sutter with FRP door frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and solid core FRP shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of Double leaf fully glazed Door shutters with 5.50 mm thick glass.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section with Vertical & Top rail: [email protected] kg/m, Bottom rail: 100x44.45x2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/mAlu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/mAlu. Handle: 100x30mm @ 0.988 kg/m and necessary accessories such as Alu. clips rubber beading, full length of handles on both sides, lock, furniture fittings such as, Hinges, Automatic door closer, rubber bush, stopper including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the reuired extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc. complete. All the Alu. Section are to be anodised with matt finish under electically contolled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc., complete.

Supplying , fabricating and fixing in position Aluminium Anodised natural colour mat finish Four track sliding window in all floors with Aluminium sections of outer frame Bottom Track [email protected] kg/m,Top & vertical 92.34x29.70x1.50 at 1.066 kg/m,and Shutter Vertical 39x20x1.50 at 0.493 kg/m, Top&Bottom 18x36.6x1.50at0.439 kg/m, Vertical locking arrangement 28.94x39x1.50at0.632 kg/m with necessary accessories such as rubber beadings, special hinges, lock, handle including supplying and fixing 4mm thick plain glass including cost of all materials , labours, power consumption required for fabrication , drilling holes in RCC colunm, slab, masonry walls wherever necessary with power drills to the required extent and make good to the original condition after fixing and also as directed.The aluminium sections are to be anodised with matt finish under electrically controlled in accordance with IS 1868 / 1962 for an average anodic film thickness 15 microns etc., complete.

Supplying , fabricating and fixing in position Aluminium Anodised natural colour mat finish Two track sliding window in all floors with Aluminium sections of outer Frame bottom 62x37mmx1.50mm at 1.218 kg/m,the Side & Top 62x31.50x1.50mm at 0.778 kg/m,Shutter Top 40x18x1.5 at 0.38 kg/m,Bottom 40x18x1.5 at 0.38kg/m, Side Vertical 40x18x1.50mm at 0.493 kg/m, Vertical locking section 40x29x1.5mm at 0.632 kg/m, with necessary accessories such as rubber beadings, special hinges, lock, handle including supplying and fixing 4mm thick plain glass including cost of all materials , labours, power consumption required for fabrication , drilling holes in RCC colunm, slab, masonry walls wherever necessary with power drills to the required extent and make good to the original condition after fixing and also as directed.The aluminium sections are to be anodised with matt finish under electrically controlled in accordance with IS 1868 / 1962 for an average anodic film thickness 15 microns etc., complete.

Supplying, fabricating and fixing in position of Aluminium Natural Colour Mat finilsh Fixed Glazing the glass used shall be of 5 mm thickness. The Aluminium Section are to be anodised under electrically controlled condition as per IS 1868/1962 for an anodic film thickness of 15 microns. All the materials should be got approved by got approved by the Executive Engineer before execution of works.

Supplying, fabricating and fixing inposition Aluminium anodised natural colour matt finish louvered ventilator size 600mm x 600 mm of with outer frame section with 62x38x2mm at 1.174 kg/m and the louvered with moving arrangements made with aluminium channel of size 60x30x4mm @ 1.274 kg/m ALuminium clips 19.05x 17.27/ 11.05x 0.075mm @ 0.169kg/m with necessary 4mm thick plain glass panel for louvers including cost of all materials, labour and power required for fabrications, chipping dismantling making holes in RCC, masonry and made good to the original condition after fixing etc., complete. The Aluminium surface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 for anodic film thickness of notless than 15 Microns,etc., complete.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Providing and fixing welded M.S. grills for the window openings and any openings as per drawing with necessary screws, bolts and fixed with necessary M.S. lugs embedded in masonry with C.C. 1:2:4 and finishing the surface neatly. Design of grills and the size of members to be used shall be got approval before put into use & as directed by the departmental officers.

Paving the floor / skirting with best quality Double charged vitrified tiles of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three Manufactured sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) Size of tiles shall be 600 X 600 X 8 mm Double charged vitrified tiles- Polished / Matt

Paving the wash basin counter with best approved quality fine polished Granite Stone Slabs 18 / 20mm thick of Jet Black with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three Manufactured sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor / skirting with best approved quality Flamed finish Granite Stone Slabs of size 1200 x 600 of 16 / 18mm thick of Ruby Red, Raw silk and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three Manufactured sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Supplying and fixing jet black 20 mm thick granite stone 1200 x 600 mm to shape finished with polished on both sides, slab table rubbed, edges rounded including necessary SS 316 clamps cutting, edge chamfering and polishing etc., for urinal partition and any other partitions. Rate including all materials, labour charges, preparation of surface, necessary cutting in wall surface, consumables etc as complete with all respects complying with relevant standard specification and as directed by the departmental officers.

Extra for pre finished Double nosing to treads of steps / counter slab of Granite stone

Extra for Grooving the Granite slab of steps

Dadooing walls with following best approved quality, polished Ceramic tile of following sizes set in Cement Mortar 1:3 (One Cement and Three plastering sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. Size of Tile - 300 x 600mm x 10mm

Dadooing walls with following best approved quality, approved colour granite slab (Synthetic grey,Parasise colour) of thickness not less than 18mm of size 1200x600 / 900x600 mm, set in Cement Mortar 1:3 (One Cement and Three plastering sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:5 (One cement and Five plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. (Internal)

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. (External)

Supplying and painting the walls and ceiling with two coats of cement paint over one coat of cement primer as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades, Structural steel members etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Designing, Providing and fixing in position Hot rolled structural steel Members / Sections consists of MS joists, channels, angles, purlins, pipes, hollow tubes, runners, insert plates, flats, gate for compound wall etc. at all levels. Rate to including all materials, labour charges, scaffolding, stagging, transportation, lead & Lifts, wastage, cost of bolts, nuts, washers, welding, electrodes and connections required for the work etc., as complete with all respects complying with relevant standard specification, as directed by the departmental officers.

Supply and Erecting of 20mm Cement Fiber board with self Tapping screw Top of Board Shingles fixing with 60 mm length self tapping screws of 10g, metal and bitumen washers including cost of materials, labor, complete as per specifications

Providing and Fixing and Finishing the top of slopped roof, sun-shade with Mangalore Tiles of approved quality etc complete, complying with standard specifications. Rate to include material, labour and other necessary fixtures etc complete.

Wooden planking in Cladding including fixing to MS frame with necessary screws complete (base of the ms frame to be measured and paid separately.) Wood Plastic Composite Material

Painting the wall with Texture Finish Paint including labour charges

Providing Granular surface base to the required surface using murram, Granular soil of size varying from 4mm to 75mm including cost of material and cost of labour for stacking, spreading and consolidating layer by layer (Each layer not exceeding 100mm) including hire charges of Roller etc, complete as per the direction of Departmental officers.

Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers.

Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete .

Supplying and laying interlocking Rubber Moulded Hydraulic Pressed Paver Block M40 grade 83mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 50mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers, sweeping tranporting loading unloading of laying paver block as per standard specification,. Natural grey colour

Providing guildeline road marking kerb painting (special acrylic medium pigmented ) involving cleaning the surface free of dirt and loose particles applying one coat of primer and applying one layer of 20 to 25 microns. Rate shall include for all materials & labour components etc., as complete all respects complying with relevant IRC specifications, as directed by the departmental officers.

Supplying and fixing in position white/ colour special delux model glazed cascade type paryware/Hindware/Equivalent wall mounted European water closet of best quality and approved make with 100mm "P" or "S" trap connecting with CI pipe of 100mm dia/ PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing,spun yarn, teak wood plugs,brass screws, etc., including supplying and fixing 10 litres capacity PVC/12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball value with polythene float with brass handle, union cuppling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 nos), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works)with 10 litres capacity flushing tank with all internal dual flush fittings with normal seat cover.Wall Fitting

Wash Hand Basin of size 550mm x 400mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia 'B' Class GI Waste Pipe, 15mm dia GM Wheel Valve,15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc Without Pedestal

Supplying, fixing, testing and commissioning of approved make 15mm CP Concealed Stop cock with one no, CP flexible tube 1.0m long, CP crutch, nozzle etc., complete.

Supplying, fixing, testing and commissioning approved make 15mm CP CP Two Way Bib Cock with Health Faucet with one no, CP flexible tube 1.0m long, CP crutch, nozzle etc., complete.

Supplying, fixing, testing and commissioning approved make Mirror 600X450 with necessary fixing screws etc complete.

Supplying, fixing, testing and commissioning approved make Urinal with piller cock fixed above counter with 32mm dia CP waste coupling, 32mm dia C.P.bottle trap with C.P. extension pipe, 1 No. C.P. flexible inlet connection pipe G.I. expansion bolts etc., complete including silicon sealant.

Supplying, fixing, testing and commissioning approved make Angle valve with necessary fittings.

INTERNAL DRAINAGE SOIL AND WASTE PIPE SYSTEM:Supplying and fixing in position UPVC specials / Pipe of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

40 mm dia

50 mm dia

UPVC PASTING TYPE SPECIALS FOR SANITARY ARRANGEMENTS

UPVC Elbow-Dia 50mm

UPVC BEND-Dia 40mm

UPVC BEND-Dia 50mm

UPVC TEE-Dia 40mm

UPVC TEE-Dia 50mm

UPVC REDUCER-Dia 50mm X 40 mm

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

75 mm dia

110 mm dia

160 mm dia

PVC PASTING TYPE SPECIALS FOR SANITARY ARRANGEMENTS

PVC Elbow-Dia 75 mm

PVC Elbow-Dia 110 mm

PVC SHOE-Dia 75 mm

PVC SHOE-Dia 110 mm

PVC Y-Dia 75 mm

PVC Y-Dia 110 mm

PVC Tee with Single Door-Dia 75 mm

PVC Tee with Single Door-Dia 110 mm

PVC Bend-Dia 75 mm

PVC Bend-Dia 110 mm

Supplying, laying, jointing, testing and comissioning of approved make PVC floor trap with C P grating with required concrete encasing all around, complete. a) 110 x 75 mm dia (20 mm water seal)

RAIN WATER SYSTEM: Supplying and fixing in position best approved of BIS quality of 110mm dia PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110 mm dia PVC elbow Specials for Rainwater down fall pipe works

110 mm dia

160 mm dia(soil pipe)

Supplying, fixing, testing and commissioning of glazed stoneware gully traps, 550x550mm C.I. grating (medium duty), 100 mm dia outlet set in PCC 1:4:8 bed, 115 thick masonry chamber in CM 1:4, internal and external plastering 12mm thick in CM 1:6, necessary earthwork, C.I. cover (medium duty) etc., complete.

Providing and constructing inspection chambers comprising burnt brick/solid block masonry walls of 230 mm thk., built in CM 1:4 over M-15 CC bed of thickness 100 mm, benching in CC M-15, internal faces plastered smooth in CM 1:4, 15mm thick and outside Rough Plastered with CM 1:6, 15mm thick including necessary earth work excavation returning and refilling and disposing surplus soil as directed by the Engineer in charge.

600 x 600 mm size internal and depth more than 450 mm but not exceeding 850 mm

600 x 600 mm size Heavy duty cover

HGS SS.20.B. Earth work excavating and depositing on bank with initial lead of 10 m & initial lift of 2m in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders SS.20B

INTERNAL WATER SUPPLY SYSTEM Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

dia 20mm

dia 25mm

dia 32mm

PVC Specials for water supply arrangements

ELBOW Dia 20mm

ELBOW Dia 25mm

ELBOW Dia 32mm

TEE Dia 20mm

TEE Dia 25mm

TEE Dia 32mm

COUPLER Dia 20mm

COUPLER Dia 25mm

COUPLER Dia 32mm

REDUCER 25 mm x 20 mm

REDUCER 32 mm x 25 mm

REDUCER 40 mm x 32 mm

EXTERNAL WATER SUPPLY SYSTEM FROM OHT Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the 40mm dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

PVC Specials for water supply arrangements

ELBOW Dia 40mm

COUPLER Dia 40mm

TEE Dia 40mm

32 mm dia ( UG SUMP TO OH TANK)

32mm dia Elbow

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

Providing and placing on terrace Polyethylene water storage Tanks as per IS 12701 : 1996 with manhole lid and suitable locking arrangements, making holes of suitable diameter for inlet, outlet and overflow pipes, including cost of all materials, labour transport charges, HOM and testing complete as per specifications.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed single core copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with GI Flush Mounting box and 6A FT switch in flush with wall with Modular cover Plate (Plastic) and making good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator) Light points with ceiling rose.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm, MS switch box with Modular coverplate along with 5A 3 pin non inter locking wall socket with 5A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point

Supply and laying of 2 x 2.5 sq.mm. (36 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in 25mm dia GI pipe (Class 'B') with necessary accessories and end supports for water pump

Supply and fixing of 3 Nos. 5A (3 pin and 2 pin) combined flush type wall socket with control switches concealed in suitable Surface box covered with Modular plate on in flush with wall with earth connection (for computer plug socket).

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug)

Supply and fixing of single box type 4'18W LED Tubelight fitting complete with electronic ballast with TW round blocks on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting

Supply, installation, testing and commissioning of 18 W LED DOWN LIGHT FITTING with IP55 cool day light suitable for pole mounting, made out CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive. ( SD 530 )

Supply and run of 2 of 2.5 sq.mm. (36 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable rigid PVC conduit pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour

Run off mains with 2 wire of 4.0 Sqm. Copper PVC conduit 25 mm dia insulated un sheathed single core 1.1. K.V. grade cable with continuous earth 1 wire of 1.5 sqmm etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer. (SD 65)

Supply and run of 1 of No.8 SWG GI wire for earth connection, including cost of all materials etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board of double door type with metal door with IP43 protection with 1 No. 32A DP MCB as incoming and 6 Nos. 6A to 32A SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (like standard make)

Supply and fixing of Vertical type 4 way triple pole neutral MCB distribution board in sheet steel enclosure, door type with metal door with IP43 protection with Four pole 32A MCB isolater as incoming and 12 Nos. 6A to 32A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection.The MCBDB and MCB's should be with the ISI mark (like standard make)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and laying of 2 x 6 sq.mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and laying of 4 x 10 sq.mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of 5A or 10A or 20A AC single phase 230V, 50 Hz Watt hour metre on suitable TW box complete with earth connections

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

Supply & Fixing of Water Tight Bulk Head Fitting suitable for LED Lamp with Guard Heavy Type

Supply & Fixing of 7 / 9 W LED bulb

Supply and run of unarmoured CAT6 cable in suitable rigid PVC conduit pipe concealed in wall and ceiling and making good of the concealed portion with suitable colour

SITC of Network Video Recorder for CCTV 4 channel 1 SATA

SITC of 4 TB Hard Disk for NVR

Supply and insallation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp

SITC of Full HD (1920 x 1080 Pixel) Dome Camera, IR illumination Range of 150m, Motorized Varifocal lens, 12x digital zoom suitable for outdoor installation.

SITC of 47.5 in. LCD display monitor (Samsung / LG / HP) with 1366 x 768 (HD) pixel resolution with all accessories. Onsite warranty of 3 years

Supply of wireless mouse.

Supply and Fixing of Cement concrete based 2 Nos statue of the 6'3" height with 1 Nos of 6'3" size bedam at proportionate details in the appropriate places.the statue decided by the architect.it should be manufactured by molding with cement concrete and reinforcement.the cast or carved figure of the statue to clear visible and sharpen and necessary painting to be done as directed by the corporation officers.the rate is including cost of materials and molding charges convince to be site and fixing in position at site etc Complete

Supply and laying of 3 -1/2 x 35 Sqmm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and laying of 3-1/2 x 16 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC LTUG aluminium armoured cable with earth connection.

Supply and fixing of brass cable gland for 4C X 16 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3-1/2 x 35 sqmm. PVC LTUG aluminium cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and providing cable end termination of 4C x 16 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and fixing of 6 Mtr GI steel tubular pole for street light with base plate of (250 x 250 x 6mm) having dimension of 76.10mm OD x 3.65mm Thick x 6000mm Length, with 1 Mtr cross arm of 32mm GI pipe for fxing of 120 Watts LED Street light fitting with inbuilt of 10 Amps 4 pole MCB suitable and etc complete.

Supply and installation of Street light feeder pillar with 63A MCB incomer and 8 Nos 32A DP MCB with sheet metal enclosure - Weather proof type with inbuilt timer control All compontents covered with Hylem sheet of 12mm thickness with necessary bolts and nuts and with earth connection complete.

Dismantling, clearing away and carefully stacking the pre coated sheets without roof timbers useful for reuse etc. Complete as directed by the corporation officers.

Dismantling M.S Pipe of different diameters by cutting machines, Conveyance, Clearing away from the site and stocking materials as directed by the corporation officers within the campus etc.., Complete.

Dismantling clearing away from the site of Brick work in Cement mortar etc., as directed by the corporation Officers etc., complete.

Dismantling clearing away from the site of Reinforced cement concrete as directed by the corporation Officers etc., complete.

Dismantling , clearing away and carefully stocking materials useful for reuse of window, Doors and Shutters including removal of frames , hinges and fastenings etc., complete.

Conveyance charges for loading and unloading of debris dismantled in the building and clearing away from the site to 10 km apart from the site through lorry service.

Random rubble masonry in cement mortar 1:5 mix with simultaneous pointing including cost and conveyance pf all materials to site and all labour charges etc complete.

Supplying and fixing in position of the Granite Stone Benches with seaters of Size 1.50 M length x 0.60m width x 0.10m thick and legs of size 0.90m height x 0.60m width x 0.10mm thick the rate is inclusive cost of all materials and labour charges etc complete.

Supplying and fixing of standard double swing ( as shown in image) which is made of M.S 3" round pipe for vertical & horizontal support with FRP seater. Charges including for cost of materials and painting etc complete

Supplying and fixing of circle swing standard ( as shown in image) which is made of M.S 3" round pipe for vertical & horizontal support outer frames and inner frames is made of M.S 11/2" round pipe with necessary aluminum sheet for seater. Charges including for cost of materials and painting etc complete

Supplying and fixing of double seesaw chair seats ( as shown in image) which is made of M.S 3" round pipe for vertical & horizontal support with FRP seater. Charges including for cost of materials and painting etc complete.

Supplying and fixing of metal slide ( as shown in image). Outer frame of slide is made of by the 3" M.S round pipe, slide sheet is made of by stainless steel (Veda) and with necessary M.S ladder with handrails. Charges including for cost of materials and painting etc complete.

Supplying and fixing of Merry go round four seats ( as shown in image) which is made of M.S 3" round pipe for vertical support and 11/2" M.S round pipe around and M.S sheet for seater with M.S 1" handrails. Charges including for cost of materials and painting etc complete.

Supplying and fixing of rope climer ( as shown in image) which is made of M.S 3" round pipe for vertical and horizontal support and inner side are connected with ropes. Charges including for cost of materials and painting etc complete.

Supplying and fixing of S type balance walk ( as shown in image) Charges including for cost of materials and painting etc complete.

Supplying and fixing of Horse spring ribeon ( as shown in image) Charges including for cost of materials and painting etc complete.

Supplying and fixing of Duck spring rideon ( as shown in image) Charges including for cost of materials and painting etc complete.

Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, deep dug in the ground,mixing the soil with decayed farmyard/ sludge manure, planting the saplings, backfilling the trench, watering,fixing the tree guard 1.50m above ground level, 0.3m below the ground level with MS wire mesh of 1"x1" opening size with 4 Nos of 12mm diameter rods of 1.80m length in which 0.30m below the ground level and maintaining the plant for one year

Providing Turffing of Mexicon Grass. The existing soil to be removed filled with suitable to a depth of 75mm of Red soil and compost. The soil to be prepared by rough dressing, fine dressing and making grass mounts, After that fertilizer and Gypsum for neutralizing soil PH over the soil bed. The gross to be free from White Ants by applying pesticides like phorate and Monocrotophos. The chemical and mechanical weeds to be controlled by applying foliarspray.

Supply and laying of springler and trip irrigation approved make and quality for 2" pvc Pipe ,1.5" pvc pipe, 2" pvc bend, 2" pvc tee,2" pvc end cap, 2" pvc ball valve, 1.5"x1.5" pvc elbow, 2" filter, Brass Popup adjustment sprinkler set of 360° x 30° and irrigation system with 60 Nos of micro sprikler nozzles emit water in the form of droplets or gentle spray including laying earth work excavation and refilling after laying in necessary places etc., complete. The rate is including Materials and labour etc., complete as directed by the corporation officers.

GST at 18%

KONGU CONSTRUCTION AND CONTRACTORS (BID ID -1164370)