REPAIR OF JOINERY, FLOORING, PLASTERING, SANITARY FITTINGS ETC AT SONEGAON , NAGPUR

Amount

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces internally finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces externally with water proofing compound finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid seperately.

M&L for 5mm thick rendering on ceiling in cement mortar (1:3) and surface finished even and smooth without using extra cement complete all as specified and directed.

M&L preparation of newly plastered or previously untreated surface of walls and applying two coats of cement base paint complete all as specified and directed.

M&L for Preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer using chalk whitening complete all as specified and directed.

M&L for applying three coats of white wash including preparation of new plastered surfaces of ceiling complete all as specified and as directed.

Supply only Integral Water proofing compound

Demolition of brick masonry built in cement mortar including all quoins/ arches/ pillars etc. but excluding ashlars facings, dressed stone work, precast concrete articles and disposing off the rubbish debris to distance exc. 250m and n. exc. 500m complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exceeding 6 metre mean radius with old size bricks built in CM 1:6 all as specified and as directed.

Demolition of PCC in ground floor and paving n. exc. 15cm thick below or above ground level including removal of debris outside MD land complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate ase in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L 75mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection finished even and fair complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L Non - skid coloured Ceramic colour tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors laid over 15mm thick screed bed in CM 1:6 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L Non - skid coloured Ceramic colour tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors laid over 15mm thick screed bed in CM 1:6 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L Glazed Ceramic colour tiles 350X450X 7 to 8 mm thick on vertical surfaces such as skirting/dados including back coat of plaster in CM 1:3 10mm thick complete all as specified and as directed.

M&L Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, laid over 20mm thick screed bed in CM 1:6 in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L Vitrified Ceramic tiles light shade 10 mm thick on vertical surfaces such as skirting/dados including back coat of plaster in CM 1:3 10mm thick complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid dry all as specified and directed.

M & L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

S&F in repair Health faucet (ABS Body ) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

Taking up or down 15 mm bore GI tubing pipe and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

All as per Item No 24 here in before , but 20 mm bore complete all as specified and as directed.

S&F Galvanised steel water tubing medium grade 15mm bore conforming to IS specifications and ISI marked with all fittings such as bends, tees, unions, elbows, connecting pieces, plugs, sockets etc fixed on walls/ceiling or laid in floors etc., complete all as specified and as directed.

All as per Item No 26 here in before , but 20 mm bore complete all as specified and as directed.

M & L for Cutting existing 15 mm steel tubing for alterations or additions (each cut measured) complete all as specified and as directed.

All as per Item No 28 here in before , but 20 mm bore complete all as specified and as directed.

All as per Item No 28 here in before , but 25 mm bore complete all as specified and as directed.

Taking down and Refixing 15 mm old steel tubing and connections in new or old position (walls, ceiling, floors etc.) complete all as specified and as directed.

All as per Item No 31 here in before , but 20 mm bore complete all as specified and as directed.

All as per Item No 31 here in before , but 25 mm bore complete all as specified and as directed.

S & F 100 mm dia cast iron nahani trap with grating including joint to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

Disconnecting existing tanks of capacity exc 500 Litres but n.exc 1000 Litres, setting aside (or lowering if required) for repairs, cleaning etc. and hoisting if required reconnecting and refixing in position complete all as specified and as directed. Note : cleaning, repairing etc. shall be measured and paid separately

M & L for cleaning and removing all scale and dirt etc from tanks (Exc.500 ltr n.exc 1000 ltr) and from mouths of circulating pipes etc. complete all as specified and as directed.

Dismantling water tank of capacity exc. 500 Litre but n.exc.1000 Litre, open or closed and removing to stores complete all as specified and as directed.

S&F Rotational Moulded Polyethylene water storage tanks, three layered (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part - I of capacity 500 litres complete all as specified and as directed.

All as per Item No 38 here in before , but 1000 litres capacity complete all as specified and as directed.

S&F in repairs Bib tap 15 mm bore, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle confirming to IS screwed down, screwed for iron pipes or for brass ferrule, complete all as specified and as directed.

S & F in repair 15 mm bore Bib taps standard of PTMT but with long body (Minimum weight 15mm-120gms) any colour high pressure screwed for iron pipes and fixed complete all as specified and as directed.

S&F in repairs 15mm dia brass stop valves fancy type chromium plated screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repair 15mm dia chromium plated fancy type stop valve with long shank & cup (concealed type) cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed complete all as specified and directed.

S&F in repairs 15mm bore Pillar taps, cast copper alloy, fancy type with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed.

S&F in repair Brass chromium plated shower rose 125mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and as directed.

S&F in repairs 60cm long PTMT towel rail fixed with and including chromium plated brass screws and plastic cleats (minimum weight 190g) complete all as specified and directed.

S&F PTMT grating doom 125mm dia with waste hole (Minimum weight 40g) all as specified and directed.

S&F in repairs PTMT shelf fixed with and including chromium plated brass screws and plastic cleats (minimum weight 300g) complete all as specified and directed.

S & F in repairs sheet glass shelf assembly consisting of 5.5mm thick glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F PVC cabinet size 450x600mm with looking mirror complete all as specified and directed. Make - Prayag or its equivalent make.

S&F vitreous china wash hand basin, white, flat back of size 550mm x 400mm including 32mm waste coupling and waste pipe etc., fixed in repairs complete all as specified and directed.

M&L vitreous china wash down water closet pedestal pattern white with including white coloured PVC seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device including connections to drain (or outgoing pipe) and flush pipe etc. fixed in repairs complete all as specified and directed.

S&F vitreous china wash down water closet squatting pan Orissa pattern of size 580 x 440mm with integral foot rest (white or light coloured) including provision of lime concrete bedding including making necessary connection to soil pipes and flushing cistern fixed in repairs complete all as specified and directed.

S & F in repair Vitreous China urinals, (half stall urinal) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and as directed.

S & F Urinal spreader 300 mm length of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60 gms) complete all as specified and directed.

S & F in repair 10 ltrs capacity PVC valveless, syphonic action type,flushing cistern,low level,white,with inlet ,ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC. 32 mm dia for low level cistern complete all as specified and as directed.

S&F 110mm dia UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall etc. including demolition and breaking up existing pipe complete all as specified and directed.

S&F in repairs UPVC (SWR) bend any radius suitable for 110mm dia pipes complete all as specified and directed.

S&F 75mm dia UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall etc. including demolition and breaking up existing pipe complete all as specified and directed.

S&F in repairs UPVC (SWR) bend any radius suitable for 75mm dia pipes complete all as specified and directed.

S & F in repair stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof suitable for 100mm dia pipe complete all as specified and directed.

S&F in repairs 15mm PVC connection 600mm long with PTMT nuts of superior quality all as specified and directed.

S&F in repairs 15mm PVC connection 900mm long with PTMT nuts of superior quality all as specified and directed.

S&F Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device complete all as specified and as directed.

S&F in repairs PTMT waste coupling of size 32mm/ 40mm (half or full threaded) (minimum weight -45 gms) suitable for wash basin, kitchen sink and urinal all as specified and directed.

S&F in repairs ball valve PTMT with epoxy coated aluminium rod for 20mm bore pipe, weight not less than 210gms, high pressure with polyethylene high density float and complete screwed for iron pipe complete all as specified and as directed.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking of shutter from the frame) of any description alongwith fittings n. exc. 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking of shutter from the frame) of any description alongwith fittings exc. 1.5 Sqm n. exc. 4 Sqm each complete all as specified and directed.

S&F 2nd class hardwood plain solid straight chowkats and frames wrought, framed, rebated on solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S & F Pressed steel door for frames of size 105x60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete complete all as specified and directed.

M&L MS work in bands, straps, supports of stays, hook and pintle hinges, clamps, hold fasts, guard bars, grills, bolts and similar items conforming to FE-290, Gde E 165, complete all as specified and directed.

S&F 2nd class hardwood plain framed panelled shutters 30mm thick, (Two No of panels) with panels of timber flat on both sides (feather edged) or 12mm veneered particle board commercial veneering on both faces, the size of rail and stile as per IS: 1003 (Part-I), kiln seasoned & chemically treated and fitted to chowkats complete all as specified and directed.

S&F 2nd class hardwood glazed and skeleton door shutters 30mm thick open rebated and prepared to receive glass, gauge etc. ( without sash bars) edges of framing plain, chamfered, rounded fitted with cut and mitered beads for securing glass etc, size of members as specified in SSR Pt 1 section 8 clause 8.24 (a) supplied and fitted to chowkats with plain, chamfered or rounded mitered and rebated sash bars any numbers, complete all as specified and directed.

S&F in repair Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm in metal/wooden almunium frames including necessary beading, clips etc as required complete all as specified and directed.

S&F in repair Steel windows with side hung shutters including projecting type hinges,with steel handle, and steel peg stay, complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F in repair Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F in repair framed work such as grills, gratings etc., with ends of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks & similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

S&F 150mm long aluminum, anodized, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 300mm long Aluminum alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed complete all as specified and as directed.

S&F 100mm size butt hinges mild steel medium weight cold rolled complete all as specified and as directed.

S&F for 150mm long aluminum anodised extruded handles fabricated type complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds all as specified and directed.

S&F sheet glass 3mm thick plain ordinary quality and glazing with oil putty wooden beads as directed in squares n. exc. 0.50 Sqm in each pane complete all as specified and directed.

S&F 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in squares exc. 0.5 sq m in each pane all as specified and as directed.

S&F 4.0mm thick sheet glass, ordinary quality and glazing with oil putty in squares exc. 0.5 sq m in each pane all as specified and as directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm thick plain colour PVC sheet reinforced with 19mm MS square tube of 19 gauge mitred out at two corners and joined by inserting two Nos of 150mm long brackets of 15mmx15mm MS square tube inside the drilling 100mm long MS screws using PVC fastener all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

M&L for preparing new surfaces of wood of any description not otherwise described over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed.

M &L for preparation new steel and iron surfaces not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paints over one coat of primer of red oxide complete all as specified and as directed.

S&F in repair Aluminium(extruded body section) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

S & F in repair for cover of PVC water tank (any capacity) in standard shape fixed with two nos MS nut bolts, washer as required complete all as specified and directed.

S&F in repairs CP towel rail 20mm dia 600mm long complete all as specified and directed.

S & F PVC waste pipe for draining of water from wash basin and sink complete all as specified and as directed.

S&F in repairs 15mm dia chromium plated angle cock screwed down for iron pipe complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm but n. exc. 2 Sqm each and resecuring in the same opening after cutting, easening etc with new iron mongry complete all as specified and as directed.

M&L resecuring or easing and adjusting aluminium door shutter/window shutter of any type taking / without taking down shutters and refixing in the same all as directed.

M&L easing / adjusting of steel doors/ windows and oiling/ greasing for smooth functioning complete all as specified & directed by the Engg-in -charge .

Supply and fixing anodised aluminium door shutter fixed with rubber gasket, stopper, cleats, handles etc complete for aluminium frame of size 65mm x 38mm x 1.55 mm and section of bottom and lock rail shutter frame of 45mm x 45mm x 1.55 mm with and including panels of 5 mm thick plain/frosted float glass, and all necessary fittings complete all as specified and as directed.

S&F for Powder coated aluminium sliding windows for two track with 4 mm thick plain/ coloured glass fixed with powder coated aluminium standard beads/glazing clips having weight not less than 300gm per RM,locking arrangement etc and aluminium frame of size 64mmX45mmX1.55mm and shutter of section 20mm X40mm X1.55mm including taking down old steel windows with necessary all fittings complete all as per manufacturer's instructions all as specified and as directed.

S&F in repair MS hook for dia 15 mm to 50 mm GI/PVC pipe for fixing on wall or floor all as directed..

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets complete all as specified and as directed.

M& L Non asbestos fibre cement building boards 12 mm thick fixed or laid/ inserted to timber/GI/Alumi nium framework with screw including particle board, medium density, flat pressed, single layer type or three layer type, BWR grade complete all as specified and as directed.

S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

karambir constructions

PURVA ENTERPRISES

SRI JD CORPORATION