PROVN OF NEW JCOs LIVING FOR 04 X JCOs ALONGWITH TOILET, BATHROOM WITH GEYSERS AT GE FDK MIL STN

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/ loose soil.

Excavating over areas n exc 1.5 m in depth and getting out in soft/ loose soil.

M&L PCC 1:4:8 type D2 (using 40mm graded aggregate) in foundation, filling and mass concrete.

M&L RCC M-30 (Design mix) (20mm graded aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete.

M&L RCC M-30 (Design mix) (20mm graded aggregate) in Columns, pillars, piers, posts and struts.

M&L RCC M-30 (Design mix) (20mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span.

M&L for RCC M-30 (Design mix) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M&L for RCC M-30 (Design mix) in Chajjas complete all as specified.

M&L for Form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, flat, rough finished surfaces of concrete.

M&L for Form work to sides of pillars, posts, struts, piers, columnn and stanchions, Square, rectangular or polygonal rough finished surfaces of concrete.

M&L for Form work to sides and soffits of floor or roof beam, beam, hauchings, girders, bressum-emers, lintels, cantilevers, shelves incl supports overhangs etc also splays between floors and beams, flat, rough finished surfaces of concrete.

M&L for Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping).

M&L for Form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide.

S&F MS TMT CRS Bars of 10 mm dia and over,cut to length,bent to shape required including cranking, binding spirally for hooping for columns hooking ends and biniding with and including MS wire (annealed) not less than 0.9 mm dia or securining with clip all as specified.

S&F MS TMT CRS Bars of 5 mm dia and over up to 10 mm dia in stirrups, spacers and binders,cut to length bent to shape required including cranking, binding spirally for hooping for columns hooking ends and biniding with and including MS wire annealed not less than 0.9 mm dia or securining with clip all as specified.

M&L for brick work with fly ash bricks (old size bricks) straight or curved on plan exceeding 6m mean radius with old size bricks in wall built in cement mortar (1:6) complete all as specified.

M&L for brick work with fly ash bricks (old size bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar (1:4).

M&L for Anti-termite treatment for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured).

M&L for Anti-termite treatment for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface.

M&L for Anti-termite treatment for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area.

M&L for Anti-termite treatment for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall.

M&L for Polythene film, 300 micron thick @ 0.30 to 0.50 kg per sqm conforming to IS specification with lap joints 100mm complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point.

M&L for Hardcore of broken stone or boulder of gauge exc 63 mm but n. exc 100 mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rolled/ rammed to a true surface complete all as specifid.

M&L for Earth filling under floor spreading in layers n exc 30 cm thick, watering, ramming/rolling and finishing complete all as specified.

M&L 100mm thick PCC 1:4:8 type D-2 (Using 40 mm graded aggregate), as in flooring, sub base etc complete all as specified.

M&L 25mm thick PCC 1:2:4 type B-0 (Using 12.5 mm graded aggregate), as in flooring complete all as specified.

S&F Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) (coloured tiles) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles15mm thick screed bed or bedding layer CM 1:4 for laying finishes,complete all as specified as directed by Engr-in- Charge.

All as per item No 29 here in before but as in vertical surfaces such as skirting, dados & risers to steps over 10mm thick backing coat in CM 1:4 complete.

S&F Glazed ceramic tiles (coloured tiles) in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 15 mm thick rendering in CM 1:4 on other than fair face of brick work.

M&L, Machine cut kota stone slab flooring, cills 20-25mm thick over cement screed base laid and jointed With grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.(single piece of Kota stone to be fixed in stair treads).

M&L, Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. (single piece of Kota stone to be fixed in stair risers).

M&L Rendering 15 mm thick in cement plaster 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing, finished even and smooth without using extra cement.

M&L Rendering 10 mm thick in cement plaster 1:3 on ceiling finished even and smooth without using extra cement.

M&L Rendering 15 mm thick in cement plaster 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement

M&L preparation of newly plastered or unplastered surfaces of wall and applying two coat of distemper oil emulsion white/tinted with a wall care putty finished surface complete all as specified and directed by Engr -in - charge.

M&L Preparation of new ceiling surfaces plastered or unplastered and applying two coat of white wash complete all as specified and directed by Engr -in - charge.

M&L preparation of newly plastered or unplastered surfaces of wall, soffits/ facia of chajja/ roof slab and applying two coat of cement base paint complete all as specified and directed by Engr -in - charge. Note :- Curing of surface will be carried out as per Para 15.15.3 of SSR Part-I.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

M&L mild steel framed work of Fe-290 (Gde E-165) as in Cooler stand, ladder, guard bars etc including dismantling of old iron work complete all as specified.

S&F factory made single extruded WPC (Wood polymer composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (suspention grade),calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm² and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutters and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-in-charge. (Note : stainless steel butt hinges shall be paid seperately).

S&F 35 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats.

S&F anodised aluminium frame for doors, window, ventilators with one or more rebates including joining cleat for fixing etc complete with powder coating on aluminium (minium thickness of powder coating 50 micron) as per the specification. The top & bottom horizontal members and vertical members adjacent to walls shall be fixed with floor, ceiling, walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fasteners complete including making arrangement to fix guard bars with PVC sleeves all as specified and directed.

S&F anodised aluminium door/window (glazed and gauzed both),side hung type without sash bars, aluminum section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws,anodised aluminium fitting such as peg stays 150mm long (01 no for each shutter), hinges type B-21, 100mm long (02 Nos) suitable handle (01 No) with powder coating of any colour (thickness of powder coating not less than 50micron) etc complete all as specified and directed.

M&L for providing and fixing stainless steel (Grade 304) in Window Grill / S case grill made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the Grill with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size as Specified and Directed by Engr-in -Charge.

S&F sheet glass of 3mm,ordinary quality and glazing with oil putty in squares n.exc 0.5 Sqm in each pane,complete all as specified.

S&F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-inCharge.

S&F 3mm th Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane.

S&F Solid PVC Double door frame of size 50mm x 95mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. tube in opening as per specification & drawing.

S&F Factory Made Solid PVC wood grain printed Moulded Door Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed.

S&F 100 mm long stainless steel hinges, medium weight, and fixed.

S&F 150 mm long Aluminium handles cast type anodised.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded section and fixed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasps staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminium alloy and fixed.

S&F MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete.

S&F 140 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor.

M&L preparation of new or previously untreated surface of wood or wooden based surfce any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer.

S&F MS powder coated decorative drapery rod (colour as approved) of 20mm dia approved pattern & design including decorative knobs (wall side and free side) & powder coated mild steel flat iron brackets fixed with steel screws & PVC rawl plugs/grips complete all as specified.

M&L for 18/19 mm thick both side prelaminated (One side decorative and one side plain) particle board exterior grade fixed with screws to timber frame work complete all as specified.

M&L for Plain fillets or beading of sectional area Exc 3 & n. exc 6 sq.cm of 2nd class hard wood square, rectangular or triangular in section , clean sawn, se-cured with nails or brads for securing wiremesh or similar works put together with glue pinned at joints in complete all as specified and directed by Engineer - in - Charge.

M&L PCC 1:3:6 type C0 using (12.5mm graded stone aggregate) as in back filling of pressed steel frames, bed blocks, coping, fixing of hold fasts etc including necessary formwork complete all as specified and directed by Engr-in-Charge.

M&L Rendering 10 mm thick in cement plaster 1:3 on roof, finishing the surface fair and even without using extra cement.

M&L for cement concrete 1:2:4, type BO (using 20mm graded stone aggregate) in roof kerb rounded or chambered on edges complete all as specificed and directed by Engr-in-Charge.

M&L for Roof Treatment in patches as specified below and as directed : (a) Cleaning, washing of surface and removing all existing bitumen coatings/ APP membrane completely with intense wire brushing or high speed water jet. Surface should be free from any loose paint, dust or grease. (b) All cracks upto 3mm at corner joints, channels and parapets should be treated with crack seal and bigger cracks, damaged portions and hollow areas must be repaired with polymer modified cement mortars. (c) Applying one coat of epoxy primer white diluted with potable water in the ratio of 1:1 and apply @ 0.40 kg/ sqm (0.20 Kg +0.20 Kg water). (d) Laying polyster reinforced fiber net/50 gsm Geotextile mesh, upto 300 mm on walls. (e) Applying three coat of HydroShield PUD microfibre reinforced UV resistent polyurethane (solid content 68% ) / Damp Proof ultra UV Stable fibre reinforced elastomeric liquid waterproofing membrane formulated with PU hybrid polymers (Solid content 55%)/ SmartCare PU Magnum elastomeric waterproofing coating based on hydrophobic polyurethane (solid content 85%)/Single Component Elastomeric Liquid Membrane ShaliUrethane BTD White/coloured (Elongation 400% ± 50, Solid Contents > 80% & Specific Gravity @ 30 OC 1.5 ± 0.03) @ total 2.00 Kg per sqm in two coats for maintaining thickness of 1.5mm, with paint brush/ roller upto 300 mm on walls. (f) The complete treatment to be carried out by authorised applicator of waterproofing manufacturer. Note : (i) The treatment shall be carried out as per the manufacturers instructions, and as directed by Engineer in Charge. (ii) The plan area of floor shall be considered for payment .

M&L Cement concrete 50mm thick type C2, 1:3:6 using 20mm graded stone aggregate as in plinth protection/path finishing surfaces even and fair (without using extra cement) all as specified.

S&F Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts, Seat cover,P/ Strap and flush pipe all as specified and directed.

S&F 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brakets.

S&F vitreous china wash basins, size 550x400mm white flat back including cutting for and pinning in ends of brackets or erecting stand including 32mm waste fittings, chromium plated with long screwed shanks & fly-nuts, waste pipe, flange end bedded in red lead cement and other end fixed.

S& F PVC connections 15 mm size, 450 mm long with PTMT nuts.

S&F Rotational moulded polythene water storage tanks (Cylinderical vertical with closed top) hoisted and fixed in position 500 ltrs, including 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified.

S&F 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F 20 mm stop valves, cast copper alloy,screwed down high pressure,with crutch or butterfly handle scresed both ends for iron pipe or for unions and fixed complete all as specified.

S&F 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

Supply and laying and connecting from exacting steel water tubing, 25 mm dia ISI Marked, 'medium grade' galvanised, including tube fittings Viz Tees Socket bends elbows, union nipple etc screwed and socketed joint laid in trenches/under road with all fitting complete all as specified.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings and all other fittings required except given in item number 78, 79, 80 & 81 on walls/ceiling or laying in floors complete including cutting chases in wall, floors etc and their making good in case of concealed pipe work all as specified. bore of pipe 20mm complete all as specified and directed by Engr-in-Charge.

S&F 20mm bore GI tubing med grade with all fittings fixed to walls or laid in floors complete all as specified.

S&F of 20 mm inner dia CPVC Brass Male/ Female Brass Threaded Adaptor fittings complete all as specified.

S&F of 20 mm inner dia CPVC Brass Elbow fittings complete all as specified.

S&F of 20 mm inner dia CPVC Brass T fittings complete all as specified.

S&F of 20 mm inner dia CPVC Brass Union fittings complete all as specified.

S&F 15mm bib taps, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.

S&F Brass Chromium plated wall mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed by Engineer in Charge.

S&F Centre hole Basin mixer, swan neck type for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed by Engineer in Charge.

S&F 15 mm fancy type chromium plated stop valves/angle valve, screwed down high pressure,with crutch or butterfly handle scresed both ends for iron pipe or for unions and fixed complete all as specified.

S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms).

S&F brass chromium plated towel rail 20mm dia, D type, 60cm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed by Engineer in Charge.

M&L for CP Toilet Paper Holder with flat recessed type stainless steel Complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/ floors/walls.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/ floors/walls.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement.

S&F PVC (SWR) bend any radius 110 mm bore.

S&F PVC (SWR) bend any radius 75 mm bore.

S&F PVC (SWR) vent cowl 75 mm bore.

S&F pressed steel rectangular frames for built in cupboard doors, made out of mild steel sheet 1.2 mm thick with girth of frame 185mm including MS rawls plugs and fixing 100mm long butt hinges medium weight cold rolled mild steel etc including two coats of synthetic enamel paint over a shop coat of zinc chromate primer complete all as specified and directed by Engr-in-charge.

S&F pressed steel door shutters including stiffeners made out of mild steel sheet 1.2 mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitered angle, one No of locking arrangement two nos Handle etc and applying two coats of synthetic enamel paint over a shop coat of zinc chromate primer all as per Godrej pattern complete all as specified and directed by Engr-in-charge. Note : (i) Measurement of door shutter shall be taken as exact size of cupboard opening (excluding frame and folded/ turned up portion). (ii) Stiffeners of 150mm girth and height equal to height of shutter made to shape as directed by Engr-in-charge. cost of these stiffeners shall be deemed to be included in the unit rate quoted for door shutters and no extra measurement/payment shall be made for the same.

M&L 150mm bore Concrete bed (PCC 1:4:8 type D2) to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested;

M&L 150mm bore RCC pipes, class NP2, laid and jointed complete with collars

M&L PCC 1:4:8 type D2 (using 40mm graded aggregate) in foundation, filling and mass concrete

M&L for brick work with fly ash bricks (old size bricks) straight or curved on plan exceeding 6m mean radius with old size bricks in wall built in cement mortar (1:6) complete all as specified.

M&L Rendering 15 mm thick in cement plaster 1:6 on surface other than fair face of brickwork or on one side of lathing, finished even and smooth without using extra cement

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm dia

M&L for Pre cast cement concrete 1:2:4 type B-I using 20mm graded stone aggregate as in Manhole cover including all necessary formwork and placing where directed by engineer-in-charge(Except set in cement mortar) complete all as specified & directed

S&F MS TMT Bars of 5 mm dia and over up to 10 mm dia in stirrups, spacers and binders,cut to length bent to shape required including cranking, binding spirally for hooping for columns hooking ends and biniding with and including MS wire annealed not less than 0.9 mm dia or securining with clip all as specified.

Surface Excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil

M&L for Hardcore of broken stone or boulder of gauge exc 63 mm but n. exc 100 mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rolled/ rammed to a true surface complete all as specifid.

M&L for sand filling under floors or in foundations including watering and consolidation all as directed.

M&L machine pressed precast concrete interlocking paver block with grey cement and pigment (coloured tiles) of any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade complete all as directed.

Providing factory made precast cement concrete solid block type B1, 1:2:4 (20mm graded aggregate) as in kerb stone of any size/thickness setting in cement mortar 1:4 for path edgings etc, embedded in positon including all necessary excavation, tamping ground arround blocks and removal of rubbish/surplus soil etc. complete all as directed.

M&L for point wiring complete with ISI marked 1.5 sqmm single core PVC insulated unsheathed cable 1100V grade FRLS with multistranded copper conductor drawn through concealed in wall/ceiling surface in existing PVC rigid concealed conduit suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of modular switchs, sockets, fan regulator etc covered with modular cover plate of required color fixed with brass screws and cup washers painting terminal boxes inside and outside with one coat red oxide primer including fixing and 1.5 sqmm copper conductor as earth continuity to connect common earth dolly completed for the following all as specified and directed by Engr-in-Charge :-

One light point/Fan point/Exhaust point controlled by one way switch.

One three pin socket out let 5 amps on the same board with other switches.

One 3 pin, 5A switch socket outlet point on independent board.

All as per Ser item No 112.00 above but with 2.5 Sqmm cable for 1 No 16 amps socket outlet point on independent board including 2.5 sqmm PVC insulated unsheathed cable multistranded with copper conductor green in colour as earth continuity conductor.

Supply and fixing PVC lamp holder suitable for LED 5 to 20 watt bulb complete all as specified and directed.

Supply and fixing LED bulb 1x10 watt lamp having lumanous efficiency warranty 2 year complete all as specified and directed.

S&F of LED tube light fitting 20W (4 feet long), 230V, surface and wall mounted LED batten with polycarbonate housing and integrated electronic driver and including connections up with copper conductor wire with suitable size as per specification and directed by Engineer-in-Charge.

S&F of LED tube light fitting 10W (2 feet long), 230V, surface and wall mounted LED batten with polycarbonate housing and integrated electronic driver and including connections with copper conductor wire with suitable size as per specification and directed by Engineer-in-Charge.

M&L ceiling rose 3 termincal/ PVC / polycarbonate isolated body complete all as specified and directed.

S&F Modular switch 1 way 6 amps one module switch complete all as specified.

S&F Modular Socket 6A 2/3 pin combined 2 module socket 230 volt AC supply complete all as specified.

S&F Modular switch single pole 1 way 16 amps 230 volt AC supply 1 module complete all as specified and directed.

S&F Modular socket 6A / 16A -2/3 pin, 2 module, 230 volt AC supply complete all as specified and directed.

M&L for submain wiring with two single core PVC FRLS insulated copper conductor 6 Sqmm and same 6 Sqmm for continuous earth wire drawn in existing PVC conduit and including taking down old unserviceable wire any type and making good disturbed surfaces of walls as necessary complete all as specified and directed. Note : Two run of wire and one run of earth wire shall be measured as one unit.

Supply and fixing (concealed flush to wall) factory made DB (made out of CRCA sheet not less than 1.2mm thick, fitted with DIN channel neutral link and 250 Amp rated bus bar) VTPN, 4 Way, suitable for mounting MCCB/MCB, conforming to IS-13032, DB shall be semi glosy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. The DB shall be double door type with hinged door with locking arrangement, the DBs shall be same make as MCBs, DB shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. The DBs shall be of IP-42 protection class, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge. Note :- MCCB/MCB shall be measured and paid separately under appropriate item of BOQ.

S&F MCCB 4 pole, 415 V, adjustable type, 63 Amps with breaking capacity 16 KA complete all as specified and directed by Engr-in-Charge.

S&F sheet metal enclosures for DB’s SPN 230 volts 8 way with 200 amps rated bus bar double door to the disturbed walls and surfaces area etc all as specified and directed by Engr-in-Charge.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 32 Amp, in the MCB DB complete with connection testing and commissioning to the distributed walls and surface area etc complete all as specified and directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning to the distributed walls and surface area complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 Mtr below ground level with top edge of earth plate at a depth not less than 1.5 Mtr below ground level, earth plate surrounded by 15cm thick packed layer of charcoal dust and common salt, connected to galvanized iron earth lead wire 4mm dia (8 SWG) by means of bolts, nuts and washers of galvanized iron or steel and thimbles upto equipment and other end of the earth wire connected to earthing test point and protected by galvanized iron pipe light grade 15mm dia and water pipe 20mm dia GI light grade with funnel & wire mesh, PCC chamber in cement concrete (1:2:4) type B-1 including 40mm thick pre cost RCC (1:2:4) type B-0 cover and 40 x 40 x 6mm angle iron frame on top of pit cover and excavation & earth work complete all as shown on electrical plate No. 3 of MES Schedule Part - I of SSR-2009 complete all as specified and directed by Engineer-in-Charge. Note : (a) GI wire upto earth earth test point/ equipment is included in this item. (b) Outer edge of earth pit chamber shall be 1 meter away from the outer edge of PCC chamber. (c) Minimum weight of reinforcement shall be 1 kg for each earth pit cover.

Supply and laying and connecting from existing steel water tubing, 40 mm dia ISI Marked, 'medium grade' galvanised, including tube fittings Viz Tees Socket bends elbows, union nipple etc screwed and socketed joint laid in trenches/under road with all fitting complete all as specified.

M& L for Gun-metal, globe or gate valves, 40 mm bore of pipe with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply and fixing exhaust fan steel body, AC single Phase 230V, AC supply, 300 mm sweep with bird guard four blades with louvers all fixing arrangements like wall hole, material etc complete all as specified and as directed by Engineer-in-charge.

Supply and fixing complete set of 1x10 watt LED retrofit type bulkhead fitting luminaries die cast aluminium alloy body heat resistant prismatic glass cover with specially designed gasket lamp holder etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size as per specification & directed by Engr-in-charge.

Supply and fixing LED street light 25 watt lumaniries comprising of epoxy powder coated housing, enclosed with golass cover including 40mm GI bracket and fixing arrangement in road light, security light etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable 1.5 Sqmm with suitable size as per speification & as per directed by Engineer-in-charge.

Supply and spread dry fine aggregate sand in trenches for cable cushioning all as specified on both top and bottom of cable including ramming all as specified and directed by Engr-in-Charge. Note : For the purpose of payment the punned thickness only measured.

Supplying and laying factory made un-reinforced precast concrete cable cover, class EHV, type 1 with peak, size 250mm x 150mm x 40mm standard size laid in trenches of across the cable protection.

Supply and Laying in replacement XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm 4 core in trenches/floors/wall and under road including connecting with suitable aluminium lugs and including taking up defective unserviceable cable of the any sizes all as specified and directed by Engr-in-Charge. Note: Earth work, Sand cushioning, GI pipe and cable cover for protection will be measured and paid separately.

Supply & fixing ceiling fans complete with blades, down rods, remote and accessories, 230 V, 1200mm sweep. Min air delivery 245 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as directed.

Supplying and fixing and commissioning of electric water heater (Geyser) storage type ABS body of capacity 25 litre, BEE approved 5 Star rating, 230 V , single Phase, AC supply, inner tank made out of heavy duty stainless steel sheet (Designed with single weld line, factory tested with hydraulic pressure as per latest IS code) with glass lined coating complete with all accessories such as safety valve, thermostate, NRV, connection piece PVC connection for hot and cold water, three core PVC insulated PVC Sheathed copper conductor flexible cable including 15 Amp plug suitable for existing socket and fixing material, 04 No nut bolt grouting in wall in PCC (1:2:4) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and directed by Engr-in-Charge.

Supply and installation, commissioning of desert cooler electric driven (single phase), having nominal air flow capacity of 6000 CuM per hour (or nearest size).(*Steel body) deep galvanised steel thickness 1mm body and 1mm removal side and back panel single phase 230 volts, with submersible pump of suitable size (Maximum power consumption 250 volts) ISI mark (with float valve of 15mm dia, stop valve of 15 mm dia, nut washer PVC connections of 15mm dia to air cooler complete all as specified . Note : (a) : Sufficient length of 3 core PVE sheathed round copper cable size 23/076 to enable fixing in to plug point shall be provided by contractor. (b) Arrangement of power connections and water connections to the desert cooler will be included in installation. (c) No extra payment shall be made to float valve, stop valve, nut, wahser PVC connection, leakproof joints etc and making connection from GI pipe 15 mm dia to air cooler in this regards union for GI pipe ball valves brass complete including electric connection. (d) Contractor shall submit necessary company test certificate and purhase voucher and minimum warranty of 2 years complete all as specified and directed by Engr-in-Charge

Supply and laying steel water tubeing, 15 mm dia ISI marked, 'Meduim grade' galvanised including tube fittings Viz Tees socket bends elbows, union nipple etc screwed and socketed joint laid in trenches/under road including taking down old unserviceable pipe any type with all fitting complete all as specified.

M&L for stop valve, cast copper alloy, screwed down, high pressure, fancy type, chromium plated 15mm bore of pipe, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F Mild steel framed work for cooler stand (to be fixed in multistory buildings) made out of angle iron of size 40x40x5 mm cross bracings, stiffeners, clamps and back plates, clamps, fabricated from structural steel sections including nuts, bolts, washers, welding, binding cold or hot, drilling holes for bolts, in any shape or size as inlcuding painting with two coats of synthetic enamel paint over a caot of red oxide primer etc all as directed by Engr in Charge.

M&L submain wiring with two single core PVC FRLS insulated stranded copper conductor cable of size 4 sqmm and same 4 sqmm for continuous earth wire drawn in to concealed PVC conduit and making good to disturbed area complete all as specified and directed by Engr-in-Charge. Note: Two run of wire, one run of earth wire and one round conduit shall be measured as one unit.

S & F DBOX SRCD (Socket Residual Current Device) is ready plug & play all -in-one device that provides protection to humans from electric shock due to direct or indirect contact as well as provides protection from overload and short circuit faults Single pole complete with one SPN MCB 20 Amps, 240 V, AC supply, and plug top all type as specified and directed .

SHIV SHAKTI BUILDERS (BID ID -3369905)

GOURAV M ENTERPRISES (BID ID -3370051)

mehar buildcon (BID ID -3369248)