Construction of Public Distribution Shop at Mettukuppam in Narapakkam Panchayat Under MLACDS /2024-25 Estimate Amount. 13.50 Lakhs

Amount

Earth work excavation and depositing on banks with initial lead and lift in gravelly soil stiff clay, hard stiff clay, murram, boulders mixed with gravel as per SS 20-B for foundation.

Plain Cement Concrete 1:4:8 mix using 40 mm ISS HBG metal including cost and conveyace of all materials and all labour charges, etc.

Brick work in CM 1:5 mix using country bricks, ground moulded of size 23 x 11 x 7cm for the following including curing etc., complete complying with standard specifications.

Supplying and Fabricating and placing in position MS steel or Ribbed Tor Steel for all Reinforced Cement Concrete works as per the design given including cost of steel and binding wire in all floors etc, Complete complying with stanard specification.(MS rod or RTS bar will be supplied departmentally at section stores and cost will be recoverd at issue rate). the binding wire shall supplied by the contactor.

Supplying & Erecting centering for sides & soffits including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings complete complying with standard specifications and as directed by the departmental officers.

Above Basement

Reinforced cement concrete 1: 1 1/2 :3 (One of cement one and half of sand and three of hard broken stone jelly) using 20mm gauge hard broken granite stone jelly for all reinforced cement concrete works excluding cost and fabrication of reinforcement grills.

Finishing the top of roof with one course of machine pressed tiles of size 20 x 20 x 2cm of approved quality laid in CM 1:3, 12mm thick. With water proofing compound confirming to IS by 2% by weight of cement used & the joint pointed neatly to full depth of tiles with the same water proofing compound mixed with cement mortar, Red oxide etc., complete complying with standard specifications. Rate for 10m2

Finishing the exposed surface of RCC item of work such as slabs, beams, sunshade, facia, canopy slab, staircase waist slab, landing slab etc., with CM 1:3, 10mm thick. including raking the surface. The rate is to include the cost of providing cement mortar beading or nosing for sunshades & staircase steps, landing slabs etc., complete complying with standard specifications.

Plastering with CM 1:5, 12mm thick.over the cement concrete for floor finish including curing etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.

Providing 25mm thick of granolithic pattern floor finish Using 1:2:4 mix with cost and conveyance including all other labour charges etc complete

Paving the floor with design colour ceramic tiles of size 305x305x6mm in all floors over a base layer of C.M. 1:3 mix, 20mm thick and pointed with white Cement mixed with colouring pigments at the rate of 0.3Kg/Sqm including finishing neatly and curing, etc., complete, complying with standard specifications and as directed by the departmental officers.

Dadooing the Walls with glazed tile laid in CM 1:3 mix including all charges etc complete

Colour Washing Inner area using Distemper over one coat primer including all charges etc complete

Wall Painting two coats Using with approved best quality of Exterior Emulsion paint of approved colour over the Including priming coat etc., complete complying with standard specifications and as directed by the departmental officers.

Painting new iron works for doors, windows and Ventilators, Iron bars, Weldmesh, wiremesh, screen, steel bars, flats and other similar works etc., with Two coats of approved first quality of synthetic enamel paint over the existing red oxide primer in all floors. The rate is inclusive of cost of all materials and labour, brushes and scaffolding charges etc., complete complying with standard specification.

Supply and Fabrication of Steel Rolling shutter of size 2.00 x 2.85 m includining Cost and Conveyance of all Cherges etc complete.

Towards the cost of Steel door of size 0.75mx1.80m m including all charges etc.

Towards the cost of Steel door of size 0.90mx 2.10m m including all charges etc.

Towards the cost of Steel Window of size 0.90mx1.20 m including all charges etc.

Supply and Fabrication of Steel ventiltator

Supply and fixing of TNEB meter Board suitable for 32A Single Phase service connection with 32A Fuse unit (500V) 32A neutral link and earth link (1" x 1/8" Copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit. SD 125

Supply and fixing of 15 A aerial fuse unit(500A) on suitable 100x100 mm TW concealed box with hylem sheet on the tapping pole with necessary clamps. SD-128

Supply and fixing of 16 Amps DP Switch of 500 V with matal clad with fuse and neutral (Side Handle) on suitable PWD Board with earth connection only. (SD No.144)

Supply and run of 2 of 6 sq.mm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V on 7/20 GI bearerwire for service connection mains - SD.64

Supply and run of 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in 25mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron upright and end supports for mains SD 69

Supply and fixing of WT bulk head fitting with guard (Philips / Bajaj / Crompton / K. Lite) suitable for incandescent lamp with 60 W bulb. - SD. 84

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch and making good of the concealed portion with suitable colour for PVC concealed light / Fan Point (For electronic regulator) (5 Points Per Coil) SD 17

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch and making good of the concealed portion with suitable colour for PVC concealed light / Fan Point (For electronic regulator) (5 Points Per Coil) SD 25

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3 mm thick Hylem sheet cover for 5 A 3 pin non inter lockingWall socket with 5A Flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point.SD 36

Supply and fixing of 1200 mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 300mm down rod on the existing clamp.. SD 110

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting. SD 89

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}

HARI SATHISH KUMAR (BID ID -1149611)