Reinvited for Annual repair for 600 sft area houses H No 217 to 252 of Revenue Officers Officials at Rohtak

Amount

Dismentaling cement conglomerate /terrazzo floors 25 mm to 50 mm thick without concrete base (HSR 8.26)

Scraping cement plaster(HSR.8.32 c)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level (HSR.11.7)

Conglomerate floor 40 mm thick cement concrete topping 1:2:4,(HSR.14.9)

Laying and fixing vitrified/ceramic anti skid tiles of any size of approved make in floor laid in any pattern as specified over a base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (Tiles shall be supplied by the Department). (HSR 14.93)

Laying and fixing vitrified/ceramic/glazed tiles of any size of approved make in skirting/dado, pillars, wall facing, laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (Tiles shall be supplied by the Department). (HSR 14.94)

12 mm cement plaster 1:6 on walls (HSR 15.7)

10 mm thick cement plaster 1:4 under side of ceiling (HSR 15.52)

Painting one coat with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint (HSR 16.7) (Labour rate)

White washing one coat or subsequent coat (HSR 16.46) (Labour rate)

Distempering with washable oil bound distemper (of approved manufacture)one coat on old distempered work (HSR 16.59) (Labour rate)

Distempering with washable oil bound distemper (of approve manufacture) two coats on old distempered work.(HSR 16.60) (Labour rate)

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on old work,one coat to give an even shade (HSR 16.62) (Labour rate)

Providing two coat of exterior acrylic emulsion paint. ( HSR 16.79) (Labour rate) (b) 1st quality

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material labour charges scaffolding sundries etc. complete (J.K/Birla make)(HSR 16.81) (Labour rate)

Commercial Hardwood such as hollock, champ, chikrassy & Chaplash etc ( Non-conferious timber other than teak confirming to IS specification No - 1003, Kiln seasoned) shutters with vertical styles & rails , as specified in the statement No ( I ) ( attached in the end of this chapter ) with 2 Nos. plywood panels of the specified thickness mentioned below tongued & grooved including the cost of iron hinges, screws, chocks /cleats stops etc. complete fixed in position excluding the cost of tower bolts and handles but including the labour for fixing the same (HSR 17.30) a) 35 mm thick (12 mm thick commercial plywood panel

b)30 mm thick ( 12mm thick commercial plywood panel )

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot pressesd, conforming to I.S.2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above, but including labour for fixing the same in position). (HSR 17.93) (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges:- (ii) 30 mm thick

(iii) 35 mm thick

Wire gauze fixed on chowkats with 25mm thick cover moulding of full width of commercial hard wood such as hollock, champ chikrassy and chaplash, etc., (Non-coniferous timber, other than teak, conforming to I.S. specification No. 1003, kiln seasoned). (HSR 17.33)

Supplying and fixing glass panes with moulding of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. (Non coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned)(HSR 17.36) (c) 4 mm thick (glazing area above 55 sq dm but upto 84 sq dm of each pane)

Providing and Fixing plywood, plain lining, butt-jointed, including wooden plugs (Teak), placed at 45 cm to 60cm centres, complete with necessary nails (frame work shall be payable extra). (HSR 17.47)

(f) 6mm thick commercial ply wood

Factory manufactured panelled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc., (non-coniferous timber other than teak, conforming to I.S. specification no. 1003, kiln seasoned), with 100mm wide vertical styles, 150mm wide lock rail, 200mm wide bottom rail and 100mm wide other rails, with panels of 12mm thick commercial veneered both sides particle board or plywood of B.W.R. grade, hot-pressed, including cost of iron hinges, screws, chocks/cleats, stops and nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above but including labour for fixing the same in position:(HSR.17.91)

(b) 35 mm thick

Factory-manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash, etc. (non coniferous timber other teak, conforming to I.S. specification No.1003 kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc. , complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (styles and rails of windows shutter shall be 75mm wide) (HSR 17.92)

(ii) 35 mm thick

Supplying and fixing glass panes including special metal sash putty of approved make. (HSR 18.30)

(b) glass panes 4 mm thick, exceeding 40 sq dm. areas.

Bijender Singh