Construction of Sub Treasury Building and residence (Type-III and Type-II) at Bhalei in Tehsil Salooni District Chamba HP

Amount

Excavation in soil in hilly area in all heights and depths and in all kind of soil by all means including saturated soil comprising of ordinary soil, soft rocks, hard rocks, chiseling/ wedging out of rock ( where blasting is prohibited) and their intermediate classification of soil, setting out true to the required line, grades, width cutting and trimming of side slopes to level as shown on the drawing and as directed by the Engineer-in- Charge at site according to the M.O.R.D. technical specification clause 302,303 and 1603 and sorting out useful materials and stacking the same in all leads and lifts in acquired width of the road and transportation of un-useful material for filling in road ways, camber, embankments for grade improvements and disposal of all useful material to acquired width of the road or on approved dumping sites through all modes of transporation including head load or animals transport or mechanical means along with its leveling fine dressing and hauling /carriage of machineries, materials, tools equipments and safety measures. Recovery for usefull stone of 60.08 cum (sixty decimal zero eight) @ 300/-cum (Rupees three hundred per cubic metre) only shall be effected from the contractor bill on pro-rata basis for the quality of cutting in earth work executed. Any loss to the public / private property during the course of execution shall be the absolute responsibility of the contractor which shall have to be duly compensated by him in all cases.

Earth work in excavation for structures in all depths as per drawing and technical specification clause 305 & 1603.4 including setting out, construction of shoring and bracing, removal of stumps and other deleterious materials and disposal in all lead and lift including dressing of sides and bottom and back filling in trenches with excavated Suitable materials. All work of rock cutting by blasting shall be carried out by taking all necessary precautions against soil erosion, damage to hill side, water pollution etc. and to protect stability of hill side rock shall be excavated with chiseling and wedging out rock (where blasting is prohibited). All earth work in cutting/excavation including rock excavation shall be carried out true to lines grades, side slopes, width, camber super elevation and level as shown on the drawings or as directed by the Engineer-in-Charge hauling and stacking of materials useful for construction at suitable sites and safe disposal of unsuitable cut materials in specified manner, filling of unevenness blind age and finishing the road to specified dimension or as directed by the Enginer-in-Charge. If the foundation of the structure is in an area with stagnant water or water is met with in the excavation due to spring seepage rain and other causes it shall be removed by suitable diversion, bailing out or pumping as directed and the area of the foundation or embankment shall be kept dry. Any loss to the public or private property during the course of excavation shall be the whole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Excavation in foundation and trenches in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, pick jumper work, blasting work both in soft and hard rock, chiseling / wedging out of rock (Where blasting is prohibited) and their intermediate classification of soil setting out true to the required lines, grade, width, cutting and trimming of side slopes as shown in the drawing and if water is met within the excavation due to springs, seepage, rain and other causes it shall be removed by the suitable diversion pumping or bailing out and excavation shall be kept dry wherever so required by the contractor at his own cost as directed by the engineer-in-charge and disposal of all surplus excavated soil in acquired width or at an approved dumping side including its stacking leveling dressing in all leads and lifts by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machineries and other incidentals to complete the work as per HPPWD specification 1990 Vol.I. Any loss to the public and private property during the course of execution and disposal of unserviceable material shall be absolute responsibility of the contractor which shall have to be compensated by him in all cases.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Excavation in foundation and trenches in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, pick jumper work, blasting work both in soft and hard rock, chiseling / wedging out of rock (Where blasting is prohibited) and their intermediate classification of soil setting out true to the required lines, grade, width, cutting and trimming of side slopes as shown in the drawing and if water is met within the excavation due to springs, seepage, rain and other causes it shall be removed by the suitable diversion pumping or bailing out and excavation shall be kept dry wherever so required by the contractor at his own cost as directed by the engineer-in-charge and disposal of all surplus excavated soil in acquired width or at an approved dumping side including its stacking leveling dressing in all leads and lifts by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machineries and other incidentals to complete the work as per HPPWD specification 1990 Vol.I. Any loss to the public and private property during the course of execution and disposal of unserviceable material shall be absolute responsibility of the contractor which shall have to be compensated by him in all cases.

Excavation in drains and channels etcetra in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, blasting work both in soft and hard rock, chiesling / wedging out of rock (Where blasting is prohibited) and their intermediate classification of soil setting out ture to the required lines, grade, width, cutting and trimming of side slopes as shown in the drawing and if water is met within the excavation due to springs, seepage, rain and other causes it shall be removed by the suitable divertion pumping or bailing out and excavation shall be kept dry whereever so required by the contractor at his own cost as directed by the engineer-in-charge and disposal of all surplus excavated soil in acquired width or at an approved dumping side including its stacking leveling dressing in all leads and lifts by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machinaries and other incidentals to complete the work as per HPPWD specification 1990 Vol.I. Any loss to the public and private property during the course of execution and disposal of unserviceable material shall be absolute responsibility of the contractor which shall have to be compensated by him in all cases.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete in foundation and plinth, as per drawing and technical specificationi section 802, 803 & 1202,and 1203 for nominal mix 1: 4: 8 (one cement: four sand : eight graded crushed stone aggregate 40mm (forty millimeters) nominal size and curing complete, including the cost of form work in Retaining Wall, Breast Wall etcetera, complete as per the direction of Engineer-in-Charge and as per the drawing and hauling /carriage of labour, equippments and materials to various location through all modes of transportation in all leads, lifts and other incidental complete in all respect.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Back filling with granular material behind abutments, wing walls, return walls complete as per drawing and M.O.R.D. technical specification clause 1203 and section 1604 , as per direction of Engineer-In-Charge including hauling /carriage of materials to various location through all modes of transportation in all leads, lifts and other incidental complete in all respect. The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing weep holes in brick masonry/stone masonry/plain or reinforced concrete abutment, wing wall, return wall with 100mm (one hundred millimeter) dia P.V.C. pipe extending through the full width of the structures with slope of I (v): 20(H) towards drainage face complete as per drawing and technical specification clauses 614,709 1204.3.7 including hauling /carriage of materials to various location through all modes of transportation in all leads, lifts and other incidental complete in all respect and as per the direction of Engineer-In-Charge.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

C/o Dry rubble masonry in breast wall and retaining walls revetment walls.within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Foundation, footings basis of columns etcetra and mass concrete within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etcetra upto any thickness within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Columns, pillars, posts and struts square rectangular or polygonal in plan within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depth and in all heights from floor within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Stair cases with sloping or stepped soffits excluding landing within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls upto all width and heights within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses, plinth and string courses and the like within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:6:12 (one cement isto six sand isto twelve graded stone agreegate 40 mm (forty millimetre) nominal size) and curing complete excluding cost of centring and shuttering in foundation and plinth within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement isto four sand isto eight graded crust stone agreegate 40 mm (forty millimetre) nominal size) excluding the cost of form work in foudation and plinth within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals. The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:3:6 (one cement isto three sand isto six graded stone agreegate 40 mm (forty millimetre) nominal size) and curing complete excluding cost of form work in foundation and plinth within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:3:6 (one cement isto three sand isto six graded stone agreegate 20 mm (twenty millimetre) nominal size) and curing complete excluding cost of form work in foundation and plinth within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:2:4 (one cement isto two sand isto four graded stone agreegate 40 mm (forty millimetre) nominal size) and curing complete excluding cost of form work in foundation and plinth within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals. The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:2:4 (one cement isto two sand isto four graded stone agreegate 20 mm (twenty millimetre) nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in suspended floor, roofs,landings and shelves within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:1½:3 (one cement isto one and half sand isto three graded stone agreegate 20 mm (twenty millimetre) nominal size) and curing complete excluding cost of form work and reinfocement for reinforced concrete work in foundation, footing, basis of columns and the like and mass concrete within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:1½:3 (one cement isto one and half sand isto three graded stone agreegate 20 mm (twenty millimetre) nominal size) and curing complete excluding cost of form work and reinfocement for reinforced concrete work in suspended floors, roofs, landing and shelves and their support, balconies, beams, girders, bressumerss and cantilever within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:1½:3 (one cement isto one and half sand isto three graded stone agreegate 20 mm (twenty millimetre) nominal size) and curing complete excluding cost of form work and reinfocement for reinforced concrete work in Columns, pillars, posts and struts upto floor all levels within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:1½:3 (one cement isto one and half sand isto three graded stone agreegate 20 mm (twenty millimetre) nominal size) and curing complete excluding cost of form work and reinfocement for reinforced concrete work in stair cases (except spiral stair cases) excluding landing , but including preparing the surface and finishing of nosing upto floor all level within all leads and lifts as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:1½:3 (one cement isto one and half sand isto three graded stone agreegate 20 mm (twenty millimetre) nominal size) and curing complete excluding cost of form work and reinfocement for reinforced concrete work in walls (any thickness but not less than 0.10 m (zero point one metre thickness) attached pillasters, buttresses, plinth and string courses etcetra from top of foundation level upto floor all levels within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying upto first floor level mechanically mixed and vibrated reinforced cement concrete 1:2:4(one cement istotwo sand isto four graded stone agreegate 20 mm (twenty millimetre) nominal size to give smooth and even surface including centring and shuttering etcetra but excluding cost of reinfocement in String courses copings bed plates, anchor blocks, plain window sills and the like within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:2:4 (One cement isto two sand isto four graded crushed stone aggregate 20mm (Twenty millimetre) nominal size) reinforced concrete chajjas upto any thickness and upto floor all level including finishing the exposed surfaces with cement mortor 1:3 ( One cement isto three sand) to give a smooth and even surface centering /form work and curing complet excluding the cost of reinforcement within all leads and lifts and as per the directionof the Engineer-in-cahrge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete with cost of binding wire within all leads lifts as per the direction of the Engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg. (two point seventy five) kilogram) of cement per squaremeter of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete within all leads lifts as per the direction of the Engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by theGovernment.

Second class brick work using common brunt clay building bricks in all floor level in cement mortar 1:6 (one cement isto six sand) within all leads and lifts as per the direction of the engineer-in-charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Half brick masonry using second class common brunt building brick in super structure above plinth level upto floor all levels in cement mortar 1:4 (one cement isto four sand) within all leads and lifts as per the directions of the Engineer-in-charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Stone solling properly hand packed filling interstics with spalls and consolidating including spreading water complete within all leads and lifts as per the direction of the Engineer-in-charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 40 mm (forty millimnetre) thick second class deodar wood panelled, glazed or panelled and glazed shutters for doors, windows, clerestory windows including black enamelled iron butt hinges with necessary screws within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing flush door shutters I.S.I. marked no. 2202 decorative type core of black board construction with frames of first class hard wood and well matched first class Indian teak wood ply veneering with vertical grains of cross bands and face veneer on both faces and 3 mm (three millimetre) thick plastic sheet upto 1.00 mettre ( one metre) height in side only of shutter 35 mm thick ( thirty five millimetre) thick including black enamelled iron butt hinges with necessary screws within all leads and lifts as per the direction of Engineer-in-Charge.and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing wire guage shutter using galvenised M.S. wire guage of I.S. guage designation 85-G (eighty five -G) withwire of dia 0.56 mm ( zero point fifty six millimetre) in doors ,window and clerestory windows incliding black enamelled iron butt hinges with necessary screws within all leads and lifts as per the direction of Engineer-in-Charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 19 mm (nineteen millimetre) thick water proof termit resistant commercial board of uniply or equivalent in shelves /box in cup board with butt joints and fixing with nails and screws complete within all leads and lifts as per the direction of Engineer-in-Charge.and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 25 mm (Twenty five millimetre) thick water proof termit resistant commercial board of uniply or equivalent in shelves /box in cup board with butt joints and fixing with nails and screws complete within all leads and lifts as per the direction of Engineer-in-Charge.and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing commercial ply wood of approved quality with butt jointing and nails 6 mm (six millimetre) thick in back of cup board within all leads and lifts as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

providing and fixing factory made PVC door frame single rebate of any colours of size 50x47 mm (fifty into forty seven millimetre) with a wall thickness of 5 mm (five millimetre) rigid PVC foam sheet heat bend and mitred at corners and jointed with 2 Nos (two number) of 150 mm (one hundred fifty millimetre) long brackets of 15 mmx 15mm 9fifteen millimetre into fifteen millimetre) M.S. square tube, the vertical door profiles to be reinforced with 19mminto 19 mm (ninteen millimetre into nineteen millimetre) M.S. square tube of 19 9nineteen) guage EPDM rubber gasket weather seal to be provided throughout the frame including fixing of door frame too wall with M.S. screws 100 mm (one hundred millimetre) long with wooden or rawl plugs embbedded in masonry complete as per manufacture specifications and direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

providing and fixing to existing door frames, 30 mm (thirty millimetre) thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 (nineteen) guage thickness and size of 19 mmx19 mm( ninteen millimetre into nineteen millimetre ) for style and 15 mmx15 mm (fifteen millimetre into fifteen millimetre) for top and bottom rails,M.S. frame shall a coat of steel primers of approved make and manufacture M.S. frame covered with 5 mm (five millimetre) heat moulded PVC "C" channel of size 30 mm ( thirty millimetre), 70 mm (seventy millimetre) width out of which 50 mm (fifty millimetre) shall be flat and 20 mm (twenty millimetre) shall be tapped in 45 (forty five) degree angle on either side forming style and 5 mm ( five millimetre) thick, 95 mm (Ninety five millimetre) wide ,PVC sheet out of which 75 mm (seventy five millimetre) shall be flat and 20 mm (twenty millimetre ) tapered in 45 (forty five) degree on the inner side to form top and bottom rail and 115 mm (one hundred fifteen millimetre) wide PVC sheet out of which 75 mm (seventy five millimetre) shall be flat and 20 mm (twenty millimetre) shall be tapered on both side to form lock rail ,top, bottom and lock rail shall be provided either side of the panel 10 mm (ten millimetre) thick, 20 mm (twenty millimetre) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5 mm (five millimetre) thick both side PVC sheet to be fitted in the M.S. frame welded/sealed to the style & rail , joints mitred and jointed with solvent cement adhessive including fixing of PVC shutters with existing frame with M.S. butt hinges 100x50x1.90 mm ( one hundred into fifty into one point ninty millimetre) size with necessary screws etc.complete as per manufacture specifications and direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing M.S. grill of required pattern in wooden frame window etc. with M.S. flat,square or round bar with round headed bolt and nut or by scrwes plain grill within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing alminimum sliding door bolts anodized colour and shade with bolts and nutn screws etcl complete within all leads and lifts as per the direction of the Engineer-In-Charge and other incidentals. The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. (i) 300x16mm (Three hundred into sixteen millimeters).

Providing and fixing alminimum sliding door bolts anodized colour and shade with bolts and nutn screws etcl complete within all leads and lifts as per the direction of the Engineer-In-Charge and other incidentals. The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. (ii) 250x16mm (Two hundred ito sixteen millimeters).

Providing and fixing aluminium tower bolts (barrerl type) anodized transparent or dyed to required shade and colour with necessary screws etc. complete within all leadsd and lifts as per the direction of the Engineer-In-Charge. (i) 200x10mm (Two hundred into ten millimeters).

Providing and fixing aluminium tower bolts (barrerl type) anodized transparent or dyed to required shade and colour with necessary screws etc. complete within all leadsd and lifts as per the direction of the Engineer-In-Charge. (ii) 150x10mm (One hundred into ten millimeteres)

Providing and fixing aliminum handles anodized transparent or dyed to required colour & shazde with necessary screws etc. complete within all leads & lifts as per the direction of Engineer-In-Charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. (i) 125mm (One hundred twenty five milimeters).

Providing and fixing aliminum handles anodized transparent or dyed to required colour & shazde with necessary screws etc. complete within all leads & lifts as per the direction of Engineer-In-Charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. (ii) 75mm (Seventy five millimeters).

Providing and fixing M.S. single acting spring hings with necessary screws etc. complete with in all leads and lifts as per the direction of Engineer-in-Charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing oxidized M.S. hasp and staples for cup boards 90 mm (Ninety millimetre) size with in all leads and lifts as per the direction of Engineer-in-Charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 200mm (Two hundred millimetres) bright finished hard drawn hook and eye within all leads and lifts as per the direction of the Engineer-In-Charge.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing hard wood plain square edge cover fillets beeding 19x6mm (Ninteen into six millimetre) section including mitring at junction with wooden screws and nails etc. within all leads and lifts as per the direction of the Engineer-In-Charge.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 1 mm (one millimetre) thick lamination sheet of approved shade and quality fixed with approved adhessive and nails complete within all leads and lifts as per the direction of the Engineer-In-Charge.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing magnetic catcher with screws etc. Complete within all leads and lifts as per the direction of the Engineer-In-Charge.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 40x3 mm (forty into three millimetre) flat iron holdfast 40 cm (forty centimetre) long including fixing to frame with 10 mm (ten millimetre) diametres bolts and nuts and wooden plugs and embedded in cemen concrete blocks 30x10x15 cm (thirty into ten into fifteen centimetres) in 1:3:6 (one cement isto three sand isto six graded stone aggregate 20 mm (twenty millimetre) nominal size within all leads and lifts as per the direction of the Engineer-In-Charge.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing M.S. curtain rods powder coated 25 mm (twenty five millimetre) dia including clamps fillets with brackets plugs etc. within all leads and lifts as per the direction of the Engineer-In-Charge.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing door silencer 3" (three inch) with screws etc. complete within all leads and lifts as per the direction of the Engineer-In-Charge.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

20mm (twenty millimetre) cement plaster in single coat on rough side of brick / concrete / stone masonry for interior plastering upto floor all levels including arises, internal rounded angle, chamfer and / or rounded angle not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:3 (one cement isto three sand) within all leads and lifts as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 10 mm ( ten millimetre) anti skid water proof stain and impect resistance heavy duty verified tiles Nitco or equivalent 300x300 x10 mm ( three hundred into three hundred into ten millimetre) manufactured of approved shade and colour in flooring ,treads of steps and landing laid over 12 mm (twelve millimetre) thick cement mortar 1:3 ( one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete with in all leads and lifts as per the direction of Engineer-in-Charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 10 mm ( ten millimetre) anti skid water proof stain and impect resistance heavy duty verified tiles Nitco or equivalent 300x300 x8 mm ( three hundred into three hundred intoeight millimetre) manufactured of approved shade and colour in skirting , riser of steps and dado laid over 12 mm (twelve millimetre) thick cement mortar 1:3 ( one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete with in all leads and lifts as per the direction of Engineer-in-Charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying spartic ceremic tiles 5.5 (five point five) thick Nitco or its equivalent in flooring 300x300 mm ( three hundred millimetre into three hundred millimetre) treads of steps laid on a bed of 12 mm ( twelve millimetre) thick cement mortar 1:3 ( one cement into three sand) finished with flush pointing in white cement with in all leads and lifts as per the direction of Engineer-in-Charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

White glaged tiles 6mm ( six millimetre) Nitco or its equivalent thick in heaving size 20x30 cm( twenty into thirty centimetre) in skirting risers or steps dedo 12 mm thick ( twelve millimetre) thick cement mortar 1:3 ( one cement isto three sand) and jointed with cement slurry upto all floor leve lwith in all leads and lifts as per the direction of Engineer-in-Charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying marble work ( table rubbed and polished ) in flooring 20 mm ( twenty millimetre)thick basein cement mortar 1:3 ( one cement isto three sand) including jointing with cement mortar 1:2 (one white cement into two marble dust) and admixture of pigment to match the shade of the marble 20 mm ( twenty millimetre) thick white makrana marble within all leads.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 10 mm ( ten millimetre) anti skid water proof stain and impect resistance heavy duty verified tiles Nitco or equivalent 600x600 x10 mm ( six hundred into six hundred into ten millimetre) manufactured of approved shade and colour in flooring ,treads of steps and landing laid over 12 mm (twelve millimetre) thick cement mortar 1:3 ( one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete with in all leads and lifts as per the direction of Engineer-in-Charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying spartic ceremic tiles 5.5 (five point five) thick Nitco or its equivalent 300x300 mm ( three hundred millimetre into three hundred millimetre)in skirtings, risers of steps and dado laid on a bed of 12 mm ( twelve millimetre) thick cement mortar 1:3 ( one cement into three sand) finished with flush pointing in white cement with in all leads and lifts as per the direction of Engineer-in-Charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing Uni-stone 12 mm (twelve millimetre) cladding on R$CC surface side as on faces of Arch masonry walls etc on 12 mm (twelve millimetre) thick cement plaster 1:3 9one cement isto three sand) with in all leads and lifts as per the direction of Engineer-in-Charge and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying water proofing treatment with Dr. Fixit-FASTFLEX or equivalent with two components polymer modified cementitious coating consisting of cementitious powder and a polymer liquid in two coats for first coat:- clean and saturate surface and then applying a coat of Dr. Fixit -FASTFLEX by maintaning a coverage of 6-7 sft (six to seven per square feet) per kilogram to achive one mm thickness and the same process shalltended upto 300 mm vertically. The second coat shall be applied in opposit direction after four six-hours of application of first coat then sprinkle sand on top surface of applied Dr. Fixit-FASTFLEX while still tacky over the second coat. Then apply cement mortar 1 ; 4 ( 1 cement :m 4 sand) admioxed with 200 ml (two hundred milliliter) of pidiproof LW @ 200ml (two hundred milliliter )per 50 kg (fifty kilogram) ag of cement over the floor with the suitable grediant towards drain pipe, while tyhe second coat of Dr. Fixit is still tacky ,including carriage of material within all leads and lifts and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing pre-painted galvenised steel sheet roofing over steel truss hot drip metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coated of 20 (twenty) microns over 5 9five) micron 0f primer back coat of polyster and five microns coating fixed J or L hooks bolts and nuts 8 mm ( eight millimetre) dia bitumen and G.I. limpet washer filled with required colour and laid completed as per direction of Engineer-in-Charge 0.60 mm ( zero point sixty millimetre) thick polyster galvenised steel sheet of approved colour including carriage of material within all leads and lifts and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing ridge and hip 60 cm ( sixty centimetre) over all pre-painted plain galvenised steel hot drip metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coated of 20 (twenty) microns over 5(five) micron 0f primer back coat of polyster and five microns coating fixed J or L hooks bolts and nuts 8 mm ( eight millimetre) dia bitumen and G.I. limpet washer filled with required colour and laid completed as per direction of Engineer-in-Charge 0.60 mm ( zero point sixty millimetre) thick polyster galvenised steel sheet of approved colour including carriage of material within all leads and lifts and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing valley 60 cm ( sixty centimetre) over all 0.60 cm (zero point sixty centimetre) thick pre-painted sheet in roofing with hot drip metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coated of 20 (twenty) microns over 5(five) micron 0f primer coating back coat of polyster and five microns coating fixed J or L hooks bolts and nuts 6 mm ( six millimetre) dia bitumen and G.I. limpet and bitumen washer copmplete with all accessories as required and as per direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidentials.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 15 cm ( fifteen centimetre) wide 45 cm ( forty five centimetre) over all semi circular plain G.I. sheet gutter with iron bracket 40x3 mm ( forty into three millimetre) size bolt s and nuts and washers etc. including making necessary connection with rain water pipe complete as per design 80 mm ( eighty millimetre) thick with in all leads and lifts and other incidential.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing M.S . B.P. sheet 1.66 mm to 2.00 mm ( one point sixty six to two millimetre) thick in eaves board / facia /soffit /ceiling including cutting,fixing and welding to steel roof member and applying a coat of red lead primer complete as per the direction of Engineer -in- Charge within all leads and lifts and other incidential( base member of steel work shall be paid and measure separately) 20 mm ( twenty millimetre) thick.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing on wall face PVC(Finolex) rain water pipes of working pressure not less than 4.5 kg/sqm (four point five kilogram per square metre including filling the joints with approved adhesive complete with in all leads and lifts and other incidential.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing on wall faces PVC(Finolex) accessories for rain water pipes including filling the joints with approved adhesive complete with in all leads and lifts and other incidential.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. (i) PVC Plain bend 150mm(One hundred fifty milimetre) dia.

Providing and fixing on wall faces PVC(Finolex) accessories for rain water pipes including filling the joints with approved adhesive complete with in all leads and lifts and other incidential.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. (ii) PVC Plain Shoe 150mm(One hundred fifty milimetre) dia.

Providing and fixing on wall faces PVC(Finolex) accessories for rain water pipes including filling the joints with approved adhesive complete with in all leads and lifts and other incidential.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. (iii) PVC Door Bend 150mm(One hundred fifty milimetre) dia.

Providing and fixing PVC holder bat clamps of approved design to PVC. pipes embedded in with screws and including cement concrete blocks 10cmx10cmx10cm (ten centimetre into ten centimetres into ten centimetres) with in all leads and lifts and other incidential.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 6mm (six millimetre) thick E Board (Embassed board) Ceiling of approved quality of ISI Mark including fixing to base frames with screws and clamps etc complete (frame work for base & cover fillets to be measured and paid for separately) with in all leads and lifts and other incidential.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing angle iron door,window,clerestory window frame manufactured from steel iron section of 40X40X6 mm ( forty into forty into six millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 50X25 mm (fifty into twenty five millimetre) welded or rigidly fixed by mechanical means with in all leads and lifts and other incidential.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing angle iron window frames (Double rebate) manufactured from M.S. angle section of 25x25x3mm(Twenty Five into Twenty Five into Three milimetres) and M.S. flat 125x5( One hundred twenty five into five milimetres), and M.S. Hollow section for rebate 50x25x2.5 mm ( fifty into twenty five into two point five millimetre ) with in all leads and lifts and other incidential.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing steel glazed doors, windows or ventilators of standard steel channels frame section 75X40mm (seventy five into forty millimetre) with M.S. flat 75x4mm (seventy five into forty millimetre) in combination welded together and standard section F-7B style of standard size with sash bars of T section 25x25x3mm (twenty five into twenty five into three millimetre) and angle iron 25x3mm (twenty five into three millimetre)) and joints metered and welded with 16x3.15mm (sixteen into three point one five millimetre) lugs 10 cm. (ten centimetre) long embedded in cement concrete blocks 15cm x10cmx10cm (fifteen into ten into ten centimetre) size of 1:3:6 (1cement :3sand : 6graded stone aggregate 20mm (twenty millimetre) nominal size) or with wooden plug and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings including providing and fixing of glass panes 4 mm (four millimetre) in glazed and wire gauge of designation 85 with 0.56mm (zero point five six millimetre) dia in wire gauge pannel with glazing clips and special metal sesh putty of approved make complete and applying a coat of approved steel primer after pretreatment of the surface as directed by the Enginee-in-charge. including carrage of material in all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a primming coat of red lead paint in beams joists chammels, angles, tes, flats with commection plates or angle cleets as in main and cross beems, hip and jack rafters, purlins connected to common rafters and the like within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a primming coat of red lead paint in gratings framed gaurd bars, ladders, railing, brackets and similar works within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a primming coat of red lead paint in trusses and trussed purlins in buildings within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Painting two coats(excluding priming costs)on new steel and other metal surfaces with enamel paint to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters paint other than white. Including carriage of materials within all leads, lifts and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease dirt and other foreign matter sand papering and knotting with ready mixed paint brushing wood primer pink. Including carriage of materials within all leads, lifts and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Painting two coats (excluding priming costs) on new wood and wood based surfaces with enamel paint brushing to give an any shade including cleaning the surfaces of all dirt, dust and other foreign matters sand papering and stopping, including carriage of materials within all leads, lifts and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government

6mm (Six milimetre) cement plaster to ceiling in cement mortar 1:3 (One Cement is to Three Sand) in all floor level. Including carriage of materials within all leads, lifts and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (one cement: six sand) within all leads, lifts of materials and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (one cement: six sand) within all leads, lifts of materials and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

10mm cement plaster in single coat on fair side of brick/concrete walls for internal plastering upto floor two level including arrises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement mortar 1:4 (1 cement:4 sand) within all leads, lifts of materials and other incidentals.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

White washing with lime on ceiling and/or sloping roofs and undecorated wall surfaces in all floors two coats to give an even shade including thoroughly brooming the surface to remove all dirt, dust mortar dust and other foreign matter including carriage of materials within all leads and lifts. The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Applying one coat of AcrylicWashable emulsion Spectrum quartz king or equivalent finish for interior painting with brushes plain smooth finish composed of acrylic polymere in emulsion inorganic/special pigment siliceous aggregate anti fungicides anti-rusting & foaming in two coat i/c necessary putty to give smooth even surface, sand papered smooth complete.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Applying white cement based wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing in position collapsible steel shutters with vertical channels 20 mm X10 mmX2mm (Twenty into ten into two millimetre) and braced with flat iron diagonals 20 mm X5 mm (twenty into five millimetre) size with top and bottom rails of T.iron 40 mm X40 mm X6 mm (forty into forty into six millimetre) with 38 mm dia (thirty eight millimetre)steel pulley complete with bolts and nuts locking arrangements, stoppers,handles,including applying a priming coat of red lead paint. The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing under layer for plinth protection of 75mm(Seventy five milimetres) thick (un-consolidated) bed of dry brick/stone aggregate 40mm(Forty milimetres) nominal sizes The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for 40mm thick block (in plinth protection). The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying lime concrete with graded aggregate 40mm (forty millimetre) nominal size and 40% (forty percent) mortar comprising of 1 lime putty : 1surkhi : 1 sand for surround or encasing stoneware pipes(Half Round) of the following internal diameters including concrete for bedding, necessary from work and curing complete. from work and curing complete. 250mm (two hundred fifty millimetre) .The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying 40 mm (forty millimetre) Cement concrete flooring 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm (twenty millimetre) nominal size) laid in one layer finished with a floating coat of neat cement including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Applying a coat of hot bitumen mexphalt 80/100 (Eighty/ Hundred) or equivalent using 1.70 Kgs. (one decimal seventy Kilogram’s) per square metre. On Damp Proof Course after cleaning the surface with a place of cloth lightly soaked in kerosene oil; within all leads and lifts of materials and other incidentals.

Providing and fixing110mm (one hundred ten millimetre) dia ISI marked high pressure PVC (finolex) waste and ventilating pipes with collar including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing of medium duty 500 mm(five hundred millimetre) cover weight 23.00 kg. (twenty three kilogramme) including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing Plytheline – Aluminium - Polyethylene (PE-AL-PE) composite pressure pipe U.V. stabilized with carbon black confirming to IS-15450-2004 water supply including clamp at one metre spacing, cutting, fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall. Internal work-Exposed on wall, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. (i) 1216 (one thousand two hundred sixteen) 16 mm O.D. Pipe (sixteen millimetre outer dai)

Providing and fixing Plytheline – Aluminium - Polyethylene (PE-AL-PE) composite pressure pipe U.V. stabilized with carbon black confirming to IS-15450-2004 water supply including clamp at one metre spacing, cutting, fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall. Internal work-Exposed on wall, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. (ii) 1620 (one thousand six hundred twenty ) 20 mm OD pipe (twenty millimetre outer dai)

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) Equal Tee (i) 1216 (one thousand two hundred sixteen)

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) Equal Tee (ii) 620 (one thousand six hundred twenty)

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. b) Reducing Tee. (i) 1620 (one thousand six hundred twenty ) x all branches.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. b) Reducing Tee. (ii) 2025 (two thousand twenty five ) x with all branches.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. c) Female branch TEE. (i) 1216 X 1216 X 15 mm (one thousand two hundred sixteen into one thousand two hundred sixteen inro fifteen millimetre) thread.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. c) Female branch TEE. (ii) 1620 X 1620 X 20 mm (one thousand two hundred sixteen into one thousand two hundred sixteen inro ftwenty millimetre) thread.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. d) Female elbows:- (i) 1216 X 15 mm (one thousand two hundred sixteen inro fifteen millimetre) thread.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. d) Female elbows:- (ii) 1620 X 15 mm(one thousand six hundred twenty into fifteen) thread.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. e) Male thread connector:- (i) 1216 X 15 mm (one thousand two hundred sixteen inro fifteen millimetre) thread.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. e) Male thread connector:- (ii) 1620 X 15 mm (one thousand six hundred twenty into fifteen millimetre) thread.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. e) Male thread connector:- (iii) 1620 x 20 mm (one thousand six hundred twenty into twenty millimetre) thread.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. f) Female thread connector:- (i) 1216 X 15 mm (one thousand two hundred sixteen inro fifteen millimetre) thread.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. f) Female thread connector:- (ii) 1620 X 15 mm (one thousand six hundred twenty into fifteen millimetre) thread.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. f) Female thread connector:- (iii) 1620 x 20 mm (one thousand six hundred twenty into twenty millimetre) thread.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. g) Couplers:- (i) 1216 (one thousand two hundred sixteen)

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. g) Couplers:- (ii) 1620 (one thousand six hundred twenty )

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. h) Reducers:- (i) 1620 x 1216. (one thousand six hundred twenty into one thousand two hundred sixteen )

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. h) Reducers:- (ii) 2025 X 1620. (two thousand twenty into one thousand six hundred twenty )

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) Equal Tees.:- (i) 1216 (one thousand two hundred sixteen)

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) Equal Tees:- (ii) 1620 (one thousand six hundred twenty )

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. b) Reducing Tee:- (ii) 1620 (one thousand six hundred twenty )

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. b) Reducing Tee:- (ii) 1620 (one thousand six hundred twenty )

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. c) Female branch Tee:- (i) 1216 X 1216 X 15 mm (one thousand two hundred sixteen into one thousand two hundred sixteen inro fifteen millimetre) thread.

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. c) Female branch Tee:- (ii) 1216 X 1216 X 15 mm (one thousand two hundred sixteen into one thousand two hundred sixteen inro fifteen millimetre) thread.

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. d) Female elbows:- (i) 1216 X 15 mm (one thousand two hundred sixteen inro fifteen millimetre) thread.

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. d) Female elbows:- (ii) 1620 X 15 mm (one thousand six hundred twenty into fifteen millimetre) thread.

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. e) Male thread connector:- (i) 1216 X 15 mm (one thousand two hundred sixteen inro fifteen millimetre) thread.

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. e) Male thread connector:- (ii) 1620 X 15 mm (one thousand six hundred twenty into fifteen millimetre) thread.

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. e) Male thread connector:- (iii) 1620 x 20 mm (one thousand six hundred twenty into twenty millimetre) thread.

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. f) Female thread connector:- (i) 1216 X 15 mm (one thousand two hundred sixteen inro fifteen millimetre) thread.

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. f) Female thread connector:- (ii) 1620 X 15 mm (one thousand six hundred twenty into fifteen millimetre) thread.

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. f) Female thread connector:- (iii) 1620 x 20 mm (one thousand six hundred twenty into twenty millimetre)thread.

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. g) Couplers:- (i) 1216 (one thousand two hundred sixteen)

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. g) Couplers:- (ii) 1620 (one thousand six hundred twenty )

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. h) Reducers:- (i) 1620 x 1216. (one thousand six hundred twenty into one thousand two hundred sixteen )

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS- 15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. h) Reducers:- (ii) 2025 X 1216. (two thousand twenty five into one thousand two hundred sixteen )

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level :-500 litres net capacity tank (item no.3.114) including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) 500 (five hundred ) litres net capacity tank (item no.3.114)

Fixing water metre and stop cock in galvanised mild steel tube including necessary fittings such as mild steel galvanised jam nut, socket including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) 15 mm (fifteen millimetre) nominal bore

Providing and fixing ISI marked high pressure PVC (finolex) waste and ventilating pipes with collar including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. i) 110 mm (one hundreded and Ten) nominal size.

Providing and fixing ISI marked high pressure PVC (finolex) waste and ventilating pipes with collar including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. ii) 150 mm (one hundreded fifty) nominal size.

Providing and fixing PVC (Finolex) clamps of approved design with steel screws and rawal plugs etc. complete. i) 110 mm (one hundreded and Ten millimetre) nominal size :-

Providing and fixing PVC (Finolex) clamps of approved design with steel screws and rawal plugs etc. complete. ii) 150 mm (one hundreded fifty millimetre) nominal size :-

Providing and fixing PVC (finolex) fitting and accessories, including carriage of materials within all leads and lifts :- a) Bends of required degree (any radius) :- I) Providing and fixing PVC (finolex) door bend with oval access door, insertion rubber washer 3 mm three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. i) 110 mm (one hundreded and Ten millimetre) nominal size :-

Providing and fixing PVC (finolex) fitting and accessories, including carriage of materials within all leads and lifts :- a) Bends of required degree (any radius) :- I) Providing and fixing PVC (finolex) door bend with oval access door, insertion rubber washer 3 mm three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. ii) 150 mm (one hundreded fifty millimetre) nominal size :-

Providing and fixing PVC (finolex) fitting and accessories, including carriage of materials within all leads and lifts :- a) Bends of required degree (any radius) :- I) Providing and fixing PVC (finolex) plain bend ISI marked including fixing with approved adhesive etc. complete. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.. i) 110 mm (one hundreded and Ten millimetre) nominal size :-

Providing and fixing PVC (finolex) fitting and accessories, including carriage of materials within all leads and lifts :- a) Bends of required degree (any radius) :- I) Providing and fixing PVC (finolex) plain bend ISI marked including fixing with approved adhesive etc. complete. including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. ii) 150 mm (one hundreded fifty millimetre ) nominal size :-

Providing and fixing PVC (finolex) fitting and accessories, including carriage of materials within all leads and lifts :- b) Single equal branch of required degree :- I)Providing and fixing PVC(finolex) single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete including fixing with approved adhesive etc. complete, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. i) 110 mm (one hundreded and Ten millimetre) nominal size :-

Providing and fixing PVC (finolex) fitting and accessories, including carriage of materials within all leads and lifts :- b) Single equal branch of required degree :- I)Providing and fixing PVC(finolex) single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete including fixing with approved adhesive etc. complete, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. ii) 150 mm (one hundreded fifty millimetre) nominal size :-

Providing and fixing PVC (finolex) fitting and accessories, including carriage of materials within all leads and lifts :- b) Single equal branch of required degree :- II) Providing and fixing PVC (finolex) single equal branch plain ISI marked including fixing with approved adhesive etc. complete, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. i) 110 mm (one hundreded and Ten millimetre) nominal size :-

Providing and fixing PVC (finolex) fitting and accessories, including carriage of materials within all leads and lifts :- b) Single equal branch of required degree :- II) Providing and fixing PVC (finolex) single equal branch plain ISI marked including fixing with approved adhesive etc. complete, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. ii) 150 mm (one hundred fifty millimetre) nominal size :-

Providing and fixing PVC (finolex) collars ISI marked including fixing with approved adhesive etc. Complete, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) 110 mm (one hundreded and Ten) nominal size :-

Providing and fixing PVC (finolex) collars ISI marked including fixing with approved adhesive etc. Complete, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. b) 150 mm (one hundreded fifty) nominal size :-

Providing and fixing PVC (finolex) Cowl including carriage of materials within all leads and lifts .The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) 110 mm (one hundreded and Ten millimetre) nominal size :-

Providing and fixing PVC (finolex) Cowl including carriage of materials within all leads and lifts .The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. b) 150 mm (one hundreded fifty millimetre) nominal size :-

Providing and fixing PVC floor trap(finolex) ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. i) 110 mm X 75 mm. (one hundred ten into seventy five millimetre)

Providing and fixing viterous China wash, down water closet (European Type W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement : 1 sand) seat and cover to be measured and paid for separately including carriage of materials within all leads and lifts .The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.- a) EWC of star No 20087 of size 57x35x39 cm (fifty seven into thirty five into thirty nine centimetres)

Providing and fixing 10.00 ltr. (ten litre) capacity PVC low level flushing cistern Hind ware sleek ultra design No 186575 size 42 X 39 X 14 cm (forty two into thirty nine into fourteen centimetre) or equivalent with a pair of brackets with fittings such as lead valve, syphon, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing viterous China Hind ware IS marked IS No.10010 or equivalent wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) Flat Back 550 X 400 mm (Five hundred fifty into four hundred millimetre)

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) 610 x 510 mm (six hundred ten into five hundred ten millimetre) with bowl depth 200 mm. (two hundred millimetre)

Providing and fixing C.P. brass waste for wash basin or sink including carriage of materials within all leads and lifts .The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) 32 mm dia (thirty two millimetre)

Providing & fixing 32 mm (thirty two millimetre)dia, PVC waste pipe for wash basin or sink including check nut , including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing & fixing 100 mm (one hundred millimetre) dia, C.P. grating including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing looking mirror of superior glass with plasitic frame including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing C.P. brass towel rail complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) 600 X 20 mm

Providing and fixing Acrylic shelf with C.P. brass bracket and guard rail complete, fixed to wooden plugs with C.P. brass screws including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.:-

Providing and fixing CP brass bib tap with capstan head including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) 15mm dia (fifteen millimetre)

Providing and fixing CP brass pillar tap with capstan head including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) 15mm dia -(fifteen millimetre)

Providing and fixing C.P.brass angle cocks including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) 15mm dia (fifteen millimetre)

Providing and fixing PVC connection pipe Heavy Duty with brass union including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) 600 cms (six hundred centimetres) length :- i) 15mm (fifteen millimetre) nominal bore :-

Providing and fixing brass full way valve with wheel including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. i) 15mm (fifteen millimetre) nominal bore :-

Providing and fixing brass full way valve with wheel including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. ii) 20 mm (twenty millimetre)nominal bore :-

Constructing manhole with R.C.C. top slab in 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4;8, inside plastering 15mm (fifteen millimetre)thick with cement mortar 1:3 including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) Inside size 800mmx800mm(eight hundred into eight hundred millimetre) and 500mm (five hundred millimetre) deep including precast reinforced Cement concrete manhole Cover (Medium Duty) with frame 600 mm (six hundred millimetre) dia including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.:- i) with 200mm (two hundred millimetre) thick walls of brick masonary using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand) :-

Providing and fixing ISI marked high pressure PVC (finolex) of working pressure not less than 4.5 kg/sqm (four point five kilogram per square metre) in trenches including fixing of joints properly with approved adhesive complete in all respects including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. b) 150mm (one hundred fifty millimetre) dia

Providing and fixing ISI marked high pressure PVC (finolex) of working pressure not less than 4.5 kg/sqm (four point five kilogram per square metre) in trenches including fixing of joints properly with approved adhesive complete in all respects including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government. a) Providing and fixing PVC (finolex) plain bend ISI marked including fixing with approved adhesive etc. complete.150 mm (one hundred fifty millimetre) nominal bore, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260mm x 350 and 340x430x265mm sizes, respectively with automatic flushing cistern with fittings R.S or C.I. Brackets standard size galvanised steel flush pipe and spreaders galvanised steel flush pipe and spreaders with brass unions and G.I. clamps complete, including painting of cistern and fittings, cutting and making good the walls, floors where required :one urinal basin with 5 litres Capacity, including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Constructing manhole with R.C.C top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing Inside size 800mm x 800mm and 500mm deep including C.I cover with frame. (Light duty single seal pattern - 1) 455mmx610mm internal dimensions total weight of cover and frame to be not less than 38kg. (Weight of cover 23 kg and weight of frame 15 kg.) With 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand) including carriage of materials within all leads and lifts.The rate is including royality, Malkana,Tol tax, sale tax, GST or other taxes imposed by the Government.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (1 cement : 5 sand ) C.I. Cover with frame (light duty ) 355mm x 610mm internal dimensions total weight of cover with frame to be not less than 38kg (weight of cover 23 kg. and weight of frame 15kg) R..C.C top slab with 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size ) foundation concrete 1:5:10 ( 1cement : 5 sand : 10 graded stone aggregate 40mm nominal size) inside plaster 15mm thick with cement mortar 1:3 (1 cement : 3 sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete. Inside dimensions 455 mm x 610 mm x 450 mm (four hundred fifty five into six hundred ten into four hundred fifty millimetre 0 deep single pipe line.

Pankaj Kapoor