SPECIAL REPAIRS TO BUILDING NO T-35, T-37, T-38, T-40 AND T-41 AT IRW LINE OF 17 CORPS ZONAL WKSP UNDER GE MISAMARI

Amount

Demolition of cement concrete (unreinforced) of any description in ground floor and pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of Brickwork build in cement mortar including all quoins, arches, pillars etc, of any descriptions, complete all as specified and directed.

Dismantling of timber scantling 40 sqcm and over in section in any position unframed work complete all as specified and directed.

Dismantling of timber fillet, rails, posts, rafters, purlins etc under 40 sqcm in section in framed work complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) area exceeding 1.50 sqm and not exceeding 4 Sqm each including iron mongeries complete all as specified and directed.

Dismantling plain or corrugated steel sheeting of any gauge, thickness including nainital or similar roof coverings complete all as specified and directed.

Dismantling of wall and ceiling board or insulation boards/slabs/blanckets/any thickness including cover fillets complete all as specified and directed.

Material and labour for 2nd class hard wood plain fillets, square, rectangular or triangular in section exc. 13 sqcm but n.exc 25 sqcm,clean sawn secured with nails or brads complete all as specified and directed

Material and labour for Brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 completed all as specified and directed .

Material and labour for Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 completed all as specified and directed .

Material and labour for second class clean sawn hard wood in scantlings fixed with nails complete all as specified and directed.

Supply and fix factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads etc for secuering glass excecter size of members of shutter as specified in SSR part-I, Sec -8 clause 8.20 (a) complete all as specified and directed.

Supply and fix Flush shutters 40 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides with partical board and fitted to wooden chowkats, complete all as specified and directed.

Supply and fix 2nd class hard wood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each

Supply and fix Mild steel barrel tower blots 200 mm long , stove enamelled black, with bright bolt and fixed complete all as specified and directed. Make :- Crown/Nulite/Mepro/Argent/Classic/Elite or equivalent ISI Marked fitting to be used.

Supply and fixing for 300 mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia fitted with gate using welding complete all as specified and directed. Make :- Crown/Nulite/Mepro/Argent/Classic/Elite or equivalent ISI Marked fitting to be used.

Supply and fix 100 mm size stainless steel butt hinges and fixed complete all as specified and directed. Make :- Mowjee or equivalent ISI Marked fitting to be used.

Supply and fixing 125mm size Mild steel pressed handles ,oval type,stove enamelled black complete all as specified and directed. Make :- Crown/Nulite/Mepro/Argent/Classic/Elite or equivalent ISI Marked fitting to be used.

Supply and fix in repair 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

Supply and fix in repair Drapery rod 20 mm dia, decorative type and fixed complete complete all as specified and directed.

Supply and fix in repair End stopper , decorative type and fixing brackets for the drapery rod 20 mm dia (One set comprises of 2 No of Decorative type End stopper 2 No of fixing brackets). complete complete all as specified and directed.

Supply and fix Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

Supply and fix rolled mild steel framed work as in doors or gates of angle with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering Door, etc to be prepared for hanging with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete conforming to Fe 410-W (Gde-E-250) complete all as specified and directed.

Supply and fix 0.63 mm thick galvanised corrugated steel sheeting with two corrugation side lap fixed with L type or J type or cranked hooks, bolts with grade of zinc coating complete all as specified and directed. Make:- TATA/Jindal/Bhushan/Sail or equivalent.

All as per ser item No 24 here in before but EXCEPT SHEETING complete all as specified and directed.

Supply and fix in repair Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

Supply and fix Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm fixed with stainless steel staples etc complete all as specified and directed.

Supply and fix mild steel flat iron ,bands, straps, clamps, hold fasts, wall ties and similar articles conforming to Fe-310-0 complete all as specified and directed.

Taking down steel windows, ventilators with side hung or top hung shutters, removing bent/deshaped frame including necessary welding, providing projectiong type Hinges and fixing of Handle, peg stey etc, making the shutter smooth movable and refixing the same complete all as specified and directed. Note :- Mild steel handless peg stay etc where ever required will be measured and paid on supply only under respective items.

Supply only mild steel handle of suitable size (As aproved ) for steel windows, Ventilators etc complete all as specified and directed.

Supply only mild steel peg stey of suitable size (As aproved ) for steel windows, Ventilators etc complete all as specified and directed.

Supply and fix GI snap grid of size 605x605 mm (Exposed grid system) frame work for false cceiling, including supporting Hanger of 4 mm dia GI wire, J-bolt with necessary washers, bolts and nuts for securing frame work to ceiling and to the snap grid as per specified and drawing of MES schedule part-II, complete all as specified and directed.

Supply and fix Non-Asbestos fibre cement building board 4.00 mm thick, fixed to GI sanp grid on ceiling complete all as specified and directed.

Material and labour for 4 mm thick Asbestos cement plain building boards, fixed to timber framework with screws complete all as specified and directed.

Material and labour for 15 mm thick screed bed in cement mortar 1:6 for laying floor tiles complete all as specified and directed.

Material and labour for 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished rough to receive tiles as in skirting, dados etc complete all as specified and directed

Material and Labour for machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Material and Labour for 20-25 mm thick machine cut kota stone in riser of steps, skirting or dados and pillar laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Material and labour for 75mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in path/plinth protection/hard standing including finished surface finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound, Grade `A' complete all as specified and directed.

Material and labour for 15 mm thick rendering on fair faces in cement mortar (1:4) brick walls or concrete surfaces of ceiling, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer including chalk whitening etc complete all as specified and directed Make :-Snowcem/Asian guttu/Duracem/Acrocem/Ecocem/Rubicem (J&N) or equivelent.

Material and labour for Preparing newlyAC board surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

Supply and fix 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5 Sq.m in each pane including oil putty and bedding complete fitting complete all as specified and directed. Make :- Saint Gobin/Modi float/Triveni float glass/hindustan pilkington or equivalent ISI Marked

Material and labour for preparation of wood and wood based material of any description, not otherwise described over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. Make:- Berger Luxol HI Gloss/Borolac (J&N) /Nerolac/Asian paints Apcolite/Superlac (Shalimar)/Dulux or equivalent.

Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide primer to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of new steel surfaces complete all as specified and directed. Make:- Berger Luxol HI Gloss/Borolac (J&N) /Nerolac/Asian paints Apcolite/Superlac (Shalimar)/Dulux or equivalent.

Material and labour for applying two coats of synthetic enamel paint optic green over a coat of red oxide primer including preparation old CGI/PGI of any description over 10 cm width or girth complete all as specified and directed. Make:- Berger Luxol HI Gloss/Borolac (J&N) /Nerolac/Asian paints Apcolite/Superlac (Shalimar)/Dulux or equivalent.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder,ceiling roses, regulators, switch socket outlet, bulk head fittings, tube light fittings etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Taking down carefully by unscrewing from board/outlet boxes, fittings and fixture such as main switches & DBs of any size and any capacity and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Taking down ceiling fan of any sweep, keeping with safe custody and hanging/fixed in repair the same with replacement of UNSV PVC insulated PVC sheathed 3 corte multistandard copper conductor cable of size 23/0.193 from ceiling rose to fan terminal hauling, painting of ceiling fans complete in situ with synthetic enamelled paint by spraying including filling cavities with filler, one coat after cleaning all dust etc the complete all as specified and as directed.

Taking down UG cable of any type and any size and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Material and Labour for Point wiring with 1.50 sq mm (nominal area), two single core PVC insulated unsheathed , 1100 volts grade, multi-stranded copper conductor FRLS Grade, in and including PVC casing capping with teak wood boxes and 3 mm thick plastic laminated sheet top cover size with all fittings and accessories including PVC board with top cover for housing/mounting brackets switches,sockets etc, including PVC insulated unsheathed single core multi-stranded copper conductor FRLS Grade cable of size 1.5 sq mm green in colour as earth continuity conductor connected to common earth dolly for one light/point controlled by one way switch complete all as specified and directed.

All as per item No 52 here-in-before but for one ceiling fan/Exhaust fan point controled by one one way switch.

All as per item No 52 here-in-before but for one 5 Amp socket outlet three pin controled by one one way switch on the same board.

All as per item No 52 here-in-before but for one 5 Amp socket outlet three pin controled by one one way switch on independent board.

All as per item No 52 here-in-before but for 3 pin 15 Amps socket outlet independant board drawn from DB and including PVC insulated multi stranded copper conductor 2.5 sqmm 1100 volts grade and earth continuity wire 1.5 sqmm PVC insulated copper wire (Green).

Supply and fix switch piano flush type single pole one way 5 Amp 240 volts complete all as specified and directed

Supply and fix socket outlet flush type multipurpose 2/3 Pin 5 Amp two in one, 230 Volts complete all as specified and directed .

Supply and fix switch socket combination multipurpose 2/3 pin , 5 Amps flush type 230 volts complete all as specified and directed .

Supply and fix switch socket combination multipurpose 2 in 1 , 3/5 Pin, 5/15 Amps flush type 230 volts complete all as specified and directed.

Supply and fix ceiling rose surface bakelite 65 x 50 mm three terminals AC 50 Hz 230 volts complete all as specified and directed.

Supply and fix ceiling fan regulator step type, flush type heavy duty suitable to work on 230 volts AC supply complete all as specified and directed.

Supply and fix lamp holder, insulated body, with back plate for angular batten fittings with one PVC block of size 75mmX75mm for mounting the fitting including 10 watt LED lamp Cat no LHLDERHEMD8X010 of HAVELLS or equivalent in Bajaj or Crompton complete all as specified and directed.

Supply and fix sheet metal enclosures for DBs (Double door type) when MCBs to be used 240 volts 8 way with 200 Amps rated bus bar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection complete all as specified and directed.

Supply and fix MCB SPN/DP 230 volts suitable for fixing in MCB DB of Capacity 32 Amps, complete all as specified and directed. Make :- L&T cat No BB20320C or equivalent Havells/Legrand

Supply and fix MCB SP 230 volts suitable for fixing in MCB DB of Capacity 6 to 32 Amps, complete all as specified and directed. Make :- L&T cat No BB20320C or equivalent Havells/Legrand

Supply and fix wall mounted LED 18 watts, box type (decorative) light fitting, 230 volt with extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver connector block etc with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from celling rose to fitting including LED tube 4' x 18 watts complete all as directed by Engineer-in-Charge. Make :- Havells, Cat part No LHLDCLXEUL83018, LHFYBPNIA1W022 or equivalent in Bajaj & Crompton.

supply and fix Energy saving new generation 10 watts LED bulk head fitting IP 65 luminire with opel diffuser pre wired and necessary mounting arrangement provision of new 3 core multistanded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as directed by Engineer-in-Charge. Make :- Bajaj, Cat part No 11233Y or equivalent in Havells & Crompton.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for foundation and getting out in soft/loose soil complete all as specified and directed.

Returning,filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm thick, in excavated soil complete all as specified and directed.

Removal of surplus soil of distance not exceeding 50 Metre and depositing where directed at a level not exceeding 1.5 Metre above the starting point complete all as specified and directed..

Supply and spread fine dry river sand for cable cushioning in trenches complete all as specified and directed. (Note:- Sand shall be measured and paid puneshed thickness)

Supplying and laying well brunt brick,locally available best quality (Sub class 'B' bricks) laid in trenches perpendicular to UG cable protections complete all as specified and directed

Supplying, laying, testing and commissioning LT UG Cable of size 2 Core 10 Sqmm laid in trences/floor/on wall/service connection PVC insulated, sheathing and armd 1100 volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed

Supply and fix GI tubing 40 mm dia ' Light grade', in trench or on wall for the protection of UG cable complete all as specified and directed. Make :- Jindal/TATA/Prakash Surya/Swastik/Appolo/BST/Kalinga/Goodluck or equivelent.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron. Earth strip protected by GI pipe 15 mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as directed by Engineer In Charge.

M/S RANA ENGINEERING ENTERPRISE

MS Awash Ghosh and Brothers

Markson