Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

Prebid Replies with revised BoQ

NBCC (INDIA) LIMITED

(A Govt. of India Enterprise)

CENTRAL PROCUREMENT GROUP

NBCC Bhawan, 2nd Floor, Lodhi Road, New Delhi- 110003

Mail ID: [email protected]

CORRIGENDUM/ ADDENDUM 02

Sub: Tender for “Construction of 300 Bedded Hostel at Dr KSSR, New Delhi”

Ref: Our NIT No. NBCC/CPG/DRKSSR/HOSTEL/2021/290 dated 05.03.2021 published on e-

tendering website https://nbcc.enivida.com and www.eprocure.gov.in on 05.03.2021.

With reference to the above mentioned NIT, Corrigendum/Addendum No. 02 is hereby issued

1. Reply to the pre bid queries are attached herewith.

2. Previously uploaded BOQ is hereby replaced with revised BOQ under the tab ‘Tender

Documents’. The corrections in BOQ of Sub Head –IX : Earthing system + LA System under

Head of Electrical Works are highlighted in Yellow colour. However, there is no change in the

All other terms and conditions of tender shall remain same.

Encl: Reply to Pre bid queries

GAURAV Digitally signed by GAURAV

RAVINDRA GAIKWAD

GAIKWAD IST

Tender F o r : KJIHGFEDCBA

Pre-Bid Q ueries and Replies

Provision as per Tender

W o rk s Head D . E le c t r ic a l W o rk s C la r if ic a t io n / R e c t if ic a t io n R e q u ir e d in S Y S T E M + LA S y s te m , The BOQ it e m s

GRAND TOTAL 27,51,47,927.10

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

1.0 CARRIAGE OF MA TERIALS

1.1 1.1 By Mechanical T ransport including loading,unloading and st acking

Disposal of moorum/building rubbish/ malba/ similar unserviceable,

dismantled or waste material by mechanical transport including loading,

transporting, unloading to approved municipal dumping ground for lead upto

10 km for all lifts, complete as per directions of Engineer-in-charge.

2.0 SUB HEAD 1 - EARTH WORKS

Earth work in surface excavation not exceeding 30 cm in depth but exceeding

1.5 m in width as well as 10 sqm on plan including getting out and disposal of

excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-

Earth work in excavation by mechanical means (Hydraulic excavator)/manual

means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10

sqm on plan) including getting out and disposal of excavated earth lead upto

50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual

means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10

sqm on plan) including getting out and disposal of excavated earth lead upto

50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of

foundations etc. in layers not exceeding 20cm in depth, consolidating each

deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5

Excavating, supplying and filling of local earth (including royalty) by

mechanical transport upto a lead of 5km also including ramming and watering

of the earth in layers not exceeding 20 cm in trenches, plinth, sides of

foundation etc.complete

Extra for every additional lift of 1.5 m or part thereof in excavation / banking

excavated or stacked materials.

Supplying and filling in plinth with sand under floors, including watering,

ramming, consolidating and dressing complete.

Clearing jungle including uprooting of rank vegetation, grass, brush wood,

trees and saplings of girth up to 30 cm measured at a height of 1 m above

ground level and removal of rubbish up to a distance of 50 m outside the

periphery of the area cleared.

Felling trees of the girth (measured at a height of 1 m above ground

level) including cutting of trunks and branches, removing the roots and

stacking of serviceable material and disposal of unserviceable material.

Wood material shall be the property of the Owner and shall be disposed

off as per the instructions of DCF/Owner, all complete as per

specification and direction of Engineer-In-Charge

Siganture of Bidder Page 2 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

2.9.1 2.33.1 Beyond 30 cm girth upto and including 60 cm girth 25.00 each 380.60 9,515.00

2.9.2 2.33.2 Beyond 60 cm girth upto and including 120 cm girth 15.00 each 1,694.40 25,416.00

2.9.3 2.33.3 Beyond 120 cm girth upto and including 240 cm girth 5.00 each 7,860.55 39,302.75

Anti termite treatment

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-

termite treatment (excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one litre

per hole, 300 mm apart including drilling 12 mm diameter holes and plugging

with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing

2.11.1 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 2,923.05 sqm 227.05 6,63,678.50

Supply and stacking of Fly ash conforming to IRC- 58 at site, including

2.12 2.37 carriage, loading , unloading & stacking up to any lead (measured stacks will 433.50 cum 152.20 65,978.70

be reduced by 20% for payment).

Filling with available fly ash and earth (excluding rock) in trenches or

embankment in layers (each layer should not exceed 15 cm), with

intermediate layer of compacted earth (Soil density of 98%) after every four

2.13 2.38 layers of compacted depth of fly ash, sides & top layer of filling shall be done 476.85 cum 219.65 1,04,740.10

with earth having total minimum compacted thickness 30 cm or as decided by

Engineer -in-charge, including compacting each layer by rolling/ ramming and

watering, all complete as per drawing and direction of Engineer -in - charge.

TOTAL (Carried Over to Summary of Civil Works) 1,02,80,088.38

3.0 SUB HEAD 2- CONCRETE WORKS

Providing and laying in position cement concrete of specified grade excluding

the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20

mm nominal size).

1:2:4 (1 cement : 2 coarse sand (Zone-III) derived from natural sources : 4

graded stone aggregate 40mm nominal size derived from natural sources).

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40

mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls

(any thickness) including attached pilasters, columns, piers, abutments,

pillars, posts, struts, buttresses, string or lacing courses, parapets, coping,

bed blocks, anchor blocks, plain window sills, fillets, sunken floor,etc., up to

floor five level,excluding the cost of centering, shuttering and finishing :

1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal

Providing and fixing at or near ground level precast cement concrete in kerbs,

edgings etc. as per approved pattern and setting in position with cement

mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required

centering, shuttering complete.

1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20

nominal size) .

Siganture of Bidder Page 3 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and fixing up to floor five level precast cement concrete solid block,

8.3 4.7 including hoisting and setting in position with cement mortar 1:3 (1 cement :

3 coarse sand), cost of required centering, shuttering complete :

1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20

mm nominal size).

Providing and laying damp-proof course 40mm thick with cement concrete

10.3 4.10 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm sqm 347.90

Extra for providing and mixing water proofing material in cement concrete

work @ 1 kg per 50kg of cement.

Applying a coat of residual petroleum bitumen of penetration 80/100 of

approved quality using 1.7kg per square metre on damp proof course after

cleaning the surface with brushes and finally with a piece of cloth lightly

soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3

coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm

3.5 4.17 thick bed of dry brick ballast 40 mm nominal size, well rammed and 396.14 sqm 614.05 2,43,251.30

consolidated and grouted with fine sand, including necessary excavation,

levelling & dressing & finishing the top smooth.

TOTAL (Carried Over to Summary of Civil Works) 48,05,900.95

SUB HEAD 3 - R C C WORKS

Reinforced cement concrete work in walls (any thickness), including attached

pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,

abutments, posts and struts etc. above plinth level up to floor five level,

excluding cost of centering, shuttering, finishing and reinforcement:

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20

mm nominal size)

Centring and shuttering including strutting, propping etc. and removal of form

4.3 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete. 1,192.83 sqm 284.85 3,39,776.83

Walls (any thickness) including attached pilasters, butteresses, plinth and

string courses etc.

4.5 5.9.3 Suspended floors, roofs, landings, balconies and access platform 6,498.89 sqm 693.05 45,04,054.23

4.7 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 5,734.25 sqm 552.05 31,65,590.26

4.8 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 3,002.12 sqm 733.70 22,02,655.44

4.9 5.9.7 Stairs, (excluding landings) except spiral-staircases. sqm 622.35

4.10 5.9.16 Edges of slabs and breaks in floors and walls

4.11 5.9.19 Weather shade, Chajjas, corbels etc., including edges sqm 766.75

Extra for additional height in centring, shuttering where ever required with

adequate bracing, propping etc. including cost of de-shuttering and

decentring at all levels,over a height of 3.5 m, for every additional height of

1 metre or part thereof (Plan area to be measured)

Suspended floors, roofs, landing, beams and balconies (Plan area to be

REINFORCED CEMENT CONCRETE

Siganture of Bidder Page 4 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Steel reinforcement for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete upto plinth level.

4.13.1 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. 1,18,096.25 kg 83.50 98,61,037.23

Steel reinforcement for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete above plinth level.

4.14.1 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500 D or more. 3,55,535.34 kg 83.50 2,96,87,201.05

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C.

DESIGN MIX CONCRETE

Providing and laying in position machine batched and machine mixed design

mix M-25 grade cement concrete for reinforced cement concrete work, using

cement content as per approved design mix, including pumping of concrete to

site of laying but excluding the cost of centering, shuttering, finishing and

reinforcement, including admixtures in recommended proportions as per IS:

9103 to accelerate, retard setting of concrete, improve workability without

impairing strength and durability as per direction of Engineer-in-

charge.“(Note :- Cement content considered in this item is @ 330

kg/cum.“Excess/ less cement used as per design mix is payable/recoverable

4.16.1 5.33.1 All works upto plinth level 1,553.40 cum 7,997.30 1,24,23,012.72

4.16.2 5.33.2 All works above plinth level upto floor V level 1,930.02 cum 9,400.85 1,81,43,801.62

Extra for providing richer mixes at all floor levels

4.17 5.34 Note:- Excess/less cement over the specified cement content used is payable

/recoverable separately.

Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:-

Cement content considered in M-30 is @ 340 kg/ cum)

Providing and fixing of expansion joint system related with floor location as

per drawings and direction of Engineer-In-Charge. The joints system will be

of extruded aluminum base members, self aligning / self centering

arrangement and support plates etc. as per ASTM B221-02. The system shall

be such that it provides floor to floor /floor to wall expansion control system

for various vertical localtion in load application areas that accommodates

multi directional seismic movement without stress to it’s components. System

shall consist of metal profiles with a universal aluminum base member

designed to accommodate various project conditions and finish floor

treatments. The cover plate shall be designed of width and thickness required

to satisfy projects movement and loading requirements and secured to base

members by utilizing manufacturer’s pre-engineered self-centering

arrangement that freely rotates / moves in all directions. The Self – centering

arrangement shall exhibit circular sphere ends that lock and slide inside the

corresponding aluminum extrusion cavity to allow freedom of movement and

flexure in all directions including

vertical displacement. Provision of Moisture Barrier Membrane in the Joint

System to have watertight joint is mandatory requirement all as per the

manufactures design and as approved by Engineer -in- Charge . (Material

shall confirm to ASTM 6063.)

4.19.1 5.44.1 Floor Joint of 100 mm gap metre 5,594.85

Siganture of Bidder Page 5 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and fixing of expansion joint system related with wall joint (internal/

external) location as per drawings and direction of Engineer-In- Charge. The

joints shall be of extruded aluminum base members, self aligning / centering

arrangement and support plates as per ASTM B221- 02. The material shall be

such that it provides an Expansion Joints System suitable for vertical wall to

4.20 5.45 wall/ wall to corner application, both new and existing construction in office

Buildings & complexes with no slipping down tendency amongst the

components of the Joint System. The Joint System shall utilize light weight

aluminum profiles exhibiting minimal exposed aluminum surfaces

mechanically snap locking the multicellular to facilitate movement. (Material

shall confirm to ASTM 6063.)

4.20.1 5.45.1 Wall Joint of 100 mm gap metre 4,658.30

Providing and fixing of expansion joint system of approved make and

manufactures for various roof locations as per approved drawings and

direction of Engineer-In-Charge. The joints shall be of extruded aluminum

base members with, self aligning and self centering arragement support

plates asper ASTM B221-02. The system shall be such that it provides

watertight roof to roof/roof to corner joint cover expansion control system

that is capable of accommodating multidirectional seismic movement without

stress to its components. System shall consist of metal profile that

incorporates a universal aluminum base member designed to accommodate

various project conditions and roof treatments. The cover plate shall be

4.2 5.46 designed of width and thickness required to satisfy movement and loading

requirements and secured to base members by utilizing manufacturer’s pre-

engineered self-centering arrangement that freely rotates / moves in all

directions. The Self centering arrangement shall exhibit circular sphere ends

that lock and slide inside the corresponding aluminum extrusion cavity to

allow freedom of movement and flexure in all directions including vertical

displacement. The Joint System shall resists damage or deterioration from

the impact of falling ice, exposure to UV, airborne contaminants and

occasional foot traffic from maintenance personnel. Provision of Moisture

Barrier Membrane in the Joint System to have water tight joint is mandatory

requirement. Material shall confirm to ASTM 6063.

4.20.1 5.46.1 Roof Joint of 100 mm gap metre 5,193.45

TOTAL (Carried Over to Summary of Civil Works) 8,37,22,386.77

5.0 SUB HEAD 4- BRICK WORKS

Brick work with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in foundation and plinth in:

5.1.1 6.1.2 Cement mortar 1:4 (1 cement : 4 coarse sand) 433.50 cum 6,157.45 26,69,254.58

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in foundations and plinth in :

5.2 6.12.2 cement mortar 1:4 (1 cement : 4 coarse sand) 867.00 sqm 773.75 6,70,841.25

Brick work with common burnt clay F.P.S. (non modular) bricks of class

5.2.1 6.4 designation 7.5 in superstructure above plinth level up to floor V level in all

shapes and sizes in :

5.3 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 2,155.69 cum 7,590.45 1,63,62,630.59

Siganture of Bidder Page 6 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Half brick masonry with F.P.S. bricks of class designation 75 in

superstructure above plinth level up to floor V level.

5.4 6.13.2 cement mortar 1:4 (1 cement : 4 coarse sand) 3,338.75 sqm 932.10 31,12,048.88

Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at

every third course of half brick masonry (with F.P.S. bricks).

Providing and laying autoclaved aerated cement blocks masonry with

150mm/230mm/300 mm thick AAC blocks in super structure above plinth

level up to floor V level with RCC band at sill level and lintel level with

approved block laying polymer modified adhesive mortar all complete as per

direction of Engineer-in-Charge. (The payment of RCC band and

reinforcement shall be made for seperately).

Random rubble masonry with hard stone in foundation and plinth including

5.7 7.1 levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12

graded stone aggregate 20 mm nominal size) upto plinth level with :

5.7.1 7.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand 52.08 Cum 6,120.80 3,18,771.26

Stone tile work for wall lining upto 10 m height with special adhesive over 12

mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including

pointing in white cement with an admixture of pigment to match the stone

5.8.1 7.38.1 8mm thick (mirror polished and machine cut edge)

5.8.2 7.38.1.1 Granite stone of any colour and shade 1,148.40 sqm 2,537.40 29,13,950.16

TOTAL (Carried Over to Summary of Civil Works) 2,63,87,937.05

5.0 SUB HEAD 5- MARBLE AND GRANITE WORKS

Providing and fixing 18mm thick gang saw cut mirror polished (premoulded

and prepolished) machine cut for kitchen platforms, vanity counters ,window

sills , facias and similar locations of required size of approved shade, colour

6.1 8.2 and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4

coarse sand) with joints treated with white cement, mixed with matching

pigment, epoxy touch ups, including rubbing, curing moulding and polishing

to edge to give high gloss finish etc. complete at all levels.

6.1.1 8.2.2 Granite of any colour and shade

Area of slab over 0.50 sum. (Granite having basic rate not less than Rs. 2000

Extra for providing edge moulding to 40 mm thick Sand stone counters,

6.2 8.3 Vanities Planter etc. including machine polishing etc. complete as per design

approved by Engineer-in-Charge.

Extra for fixing marble /granite stone over and above corresponding basic

6.3 8.4 item, in facia and drops of width upto 150 mm with epoxy resin based 355.62 metre 434.25 1,54,427.99

adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/ kitchen

sink in kitchen platform, vanity counters and similar location in

marble/Granite/stone work including necessary holes for pillar taps etc.

including rubbing and polishing of cut edges etc. complete.

Siganture of Bidder Page 7 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10

metre height, backing filled with a grout of average 12 mm thick cement

mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement

6.5 8.14 mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment

matching the stone shade : (To be secured to the backing and the sides by

means of cramps and pins which shall be paid for separately) :

Red sand stone - Exposed face machine cut and table rubbed with rough

White sand stone - exposed face fine dressed with rough backing .

TOTAL (Carried Over to Summary of Civil Works) 8,12,644.11

7.0 SUB HEAD 6- WOOD AND PVC WORKS

Providing wood work in frames of doors, windows, clerestory windows and

other frames, wrought framed and fixed in position with hold fast lugs or with

dash fasteners of required dia & length (hold fast lugs or dash fastener shall

be paid for separately).

Providing and fixing ISI marked flush door shutters conforming to IS: 2202

(Part I) non-decorative type, core of block board construction with frame of

1st class hard wood and well matched commercial 3 ply veneering with

vertical grains or cross bands and face veneers on both faces of shutters :

35 mm thick including ISI marked Stainless Steel butt hinges with necessary

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum

7.3 9.23 depth on all edges of shutters (over all area of door shutter to be measured) 897.82 sqm 401.40 3,60,384.95

Over item no. 9.21.

Extra for providing vision panel not exceeding 0.1 sum in all type of flush

7.4 9.24 doors (cost of glass excluded) (overall area of door shutter to be measured)

7.4.1 9.24.1 Rectangular or square. 160.00 sqm 173.95 27,832.00

Extra for cutting rebate in flush door shutters (Total area of the shutter to be

7.6 9.7.7 Float glass panes

7.6.1 9.7.7.2 5.0 mm thick glass panes (weight not less than 12.5 kg per sqm) 12.00 sqm 2,116.90 25,402.80

Providing and fixing bright finished brass 100 mm mortice latch and lock with

7.7 9.76 6 levers and a pair of lever handles of approved quality with necessary screws 463.00 each 712.35 3,29,818.05

Providing and fixing aluminium extruded section body tubular type universal

hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on

7.8 9.84 the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 463.00 each 851.60 3,94,290.80

1000 mm), with double speed adjustment with necessary accessories and

screws etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised

7.9 9.96 (anodic coating not less than grade AC 10 as per IS : 1868), transparent or

dyed to required colour or shade, with nuts and screws etc. complete :

Siganture of Bidder Page 8 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic

7.10 9.97 coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to

required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating

7.11 9.100 not less than grade AC 10 as per IS : 1868) transparent or dyed to required

colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked,

anodised (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour and shade, with necessary screws etc.

7.12.1 9.101.2 Twin rubber stopper 463.00 each 62.05 28,729.15

Providing & Fixing decorative high pressure laminated sheet of plain / wood

grain in gloss / matt / suede finish with high density protective surface layer

and reverse side of adhesive bonding quality conforming to IS : 2046 Type S

including cost of adhesive of approved quality.

Siganture of Bidder Page 9 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and fixing of non-metallic asbestos free composite fire cum smoke

check door frame with shutter for 2 hrs Fire Rating door system duly prior

tested for Stability, Integrity and Insulation as per criteria vide clause 9.4 as

per IS 3614 Part -II and BS 476 Part 22 for single and double leaf Doors

tested from CBRI Roorkee with following specifications 2nd class teakwood

Door Frame of section 145mm x 70mm with heat activated intumescent fire

seal strip of size 10mm x 4mm (Astroftame U.K / Marshall ) and one coat of

anti-termite fire retardant primer along Minimum 55mm thick fire / smoke

check wooden shutters of 120 minute fire rating comprising of 75mm x 49mm

hardwood internal timber frame two minimum 9mm thick Starpan/Promatect

"H" Calcium Silicate board, a 100% without asbestos, Bruclte and

Meerschaum having density not more than 950 Kg/M3 and thermal

conductivity 0.14 W/m*k Sandwiching 31mm thick fire resistance insulation

filler filled with rock wool coated with FR silicon sealant density 98kg/m3

Faced with 3mm thick commercial ply facing on both sides of the shutter with

7.14 NS1 55mm x 14mm teakwood lipping all around the shutter Heat activated 18.50 sqm 14,509.00 2,68,416.50

intumescent fire seal strips of size 10mm x 4mm (astroflame U.K.) mounted

in the grooves of hardwood lipping in three sides except bottom. The door

shutter shall be finished with 1mm thick Laminate/Decorative Veneer on both

faces as per the approved brand and shade Provision of Vision panels of

minimum size 300 x 300 mm made out of 6 mm thick clear fire rated glass

(imported) for 120 minutes fire rating of Firelite (Japan)/ Asahi ( Japan) /

Schott from (Germany) fully transparent in fire/non-fire conditions having

minimum 92% transparency with complete fire rated gasket channel &

moulding beading and filling the gap between moulding /beading and glass

with suitable sealant including fixing each shutter Fixing 4 Nos. stainless

steel ball bearing hinges of size 100mm x 76mm x 3mm with screws from

Marshall / Dorma's BB 4330 / Assa Abloy's Lockwood range. The door frame

and door shutters shall be painted with fire retardant paint of 'BERGER /

SUKRI' or equivalent to provide Class 1 surface spread of flame conforming to

BS 476 Part 7, IS : 12777 in desired shade over a coat of fire resistant

DEAD LOCK: Providing and fixing 2 hours fire rated Dead Lock of Dorma 288

Series or Briton’s EL 2010 or Marshall’s MH-L-13002 SSS as per European

standard in satin stainless finish with 80mm both side key cylinder tested to

minimum 100000 cycles and tested along with wooden / Metal fire doors for

2 hrs. fire rating from CBRI Roorkee complete in all respect as per direction of

Engineer-in-Charge.

VISION PANEL : Providing and fixing vision panel of size 300 x 300 mm of

minimum 5 mm thick clear toughened glass of approved make like Saint

Gobain / Firelite (Japan) / Schott for 120min. fire rating which can also

withstand thermal shock upto 800oC shall be used as a glazing. Vision Panel

to be fixed with required beading and fire rated acrylic sealant tested in

accordance with IS : 3614 Part -II and BS : 476 Part 20& 22 , for 120min.

fire rating for stability and integrity and insulation criteria complete in all

respect as per direction of Engineer-in-Charge. The manufacture should have

prior test certificates for both single leaf and double leaf fire doors with from

CBRI Roorkee for 2Hrs fire rating

Siganture of Bidder Page 10 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

DOOR CLOSER : Providing & Fixing exturded aluminimum body heavy duty 2

hrs fire rated door closer of approved make of Dorma TS 93 series / Brition's

LCN1460 / Marshall MH-DC-S-14016 (3-4) tested from CBRI Roorkee as per

IS : 3614 Part -II and BS : 476 Part 20& 22 from CBRI Roorkee alongwith

7.17 iii wooden /glazed / metal fire doors. The door closer shall be of type 3-4 , non 5.00 each 3,712.00 18,560.00

handed having back check function , ANSI/BHIMA certified , and complies

with EN 1154 for 100000 cycles.The door closer shall have a 10 year

mechanical guarranty / warranty from the manufacturer against any

manufacturing defects.

D- TYPE HANDLE: Providing and fixing of Dorma’s TGDID , Briton’s E series

7.18 iv and Marshall’s 304 grade stainless steel D- Type back to back pull handle of 5.00 each 2,025.00 10,125.00

size 300mm long and 22mm dia with complete roses and studs for fixing.

PANIC BAR: Providing & fixing of stainless steel 316 grade fire rated touch

type panic bar of approved make like Marshall MH -PB - SS -11001-03/

Dorma PHA 2000-1 and PHA 2003/ Von Duprin CX 98 tested in accordance

7.19 v with IS : 3614 Part - II and BS : 476 Part 20 & 22 from CBRI Roorkee for 2 5.00 each 9,853.00 49,265.00

hrs fire rating along with the wooden /glazed / metal fire doors. as a

complete assembly. The manufacturer shall provide a minimum guarranty /

warranty for 5 years against any manufacturing defects.

Providing and fixing of Hollow metal fire rated doors confirming to BS 476

part 20& 22 , IS 3614 part-1 & part-2 for stability and integrity with Pressed

Galvanized steel confirming to IS 277 with doors tested at CBRI/ NABL

approved lab for maximum rating of 2hrs tested Glass used for vision panels

to be supported by certificates confirming the required fire ratings /panels

being a part of the fire door assembly. The Doors should be finished in

Thermosetting Powder Coating desired RAL Shades and Fire Coating primer

with VOC Content for Flat: <50g/l, non flat: < 150 g/l. All Hardware should

pass European certificate "CE" of conformity / UL with required fire ratings.

Door frame shall be double rebate profile of minimum size 154mm X 77 mm

made out of min 1.50mm minimum thick galvanized steel sheet. NDRF

154x77 Frames shall be Butt jointed and field assembled with self bolted. All

provision should be mortised, drilled and tapped for receiving appropriate

hardware. Frames should be provided with back plate bracket and anchor

fasteners for installation on a finished plastered masonry wall opening. Door

leaf shall be minimum 49mm thick fully flush double skin door with or without

visionlite. Door leaf shall be manufactured from 1.0mm minimum thick

galvanized steel sheet.

Siganture of Bidder Page 11 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

The internal construction of the door should be rigid reinforcement pads for

receiving appropriate hardware. The infill material shall be mineral wool

treated with Viper FRS 881 LH/ Honey Comb Paper. All doors NSD 12049

shall be factory prepped for receiving appropriate hardware and provided with

necessary reinforcement for hinges, locks, and door closers. The edges

should be interlocked with a bending radius of 1.4mm. For pair of doors

7.21 vii astragals has to be provided on the meeting stile for both active and inactive

leaf. Visionlite wherever applicable should be provided as per manufacturers

recommendation with a beading and screws from inside. All hardware shall be

as specified in detailed specifications and to the satisfaction of engineer in

charge. The work includes carrying out tests at CBRI/ NABL approved lab and

certificates for 2 Hours fire rating as per relevant codes and standards.

Providing and fixing fire resistant door frame of section 50 x 60 mm on

horizontal side & 35 x 60 mm on vertical sides having built in rebate made

out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/

m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters.

The frame shall be filled with Mineral wool Insulation having density min

96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5

each on vertical style & 4 on horizontal style of size M10 x 80 )

suitable for fixing in the opening along with Factory made Template for SS

Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter

. The frame shall be finished with a approved fire resistant

primer or Powder coating of not less than 30 micron in desired shade as per

the directions of Engineer - in- charge . (Cost of SS

ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120

min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and

certified as per laboratory approved by Engineer-in-charge,

with suitable mounting on door frame, consisting of vertical styles, top rail &

side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out

of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled

mineral wool insulation having density min 96 kg/m³ and fixing with

necessary stainless steel ball bearing hinges of size 100x89x3mm of

approved make, including applying a coat of approved fire resistant primer or

powder coating not less than 30 micron etc all complete as per direction of

Engineer-in-charge (panelling to be paid for seperately).

Siganture of Bidder Page 12 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and fixing glazing of Pyrobel-T in fire resistant door shutters, fixed

panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I.

sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed

with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm

c/c , including

applying a coat of approved fire resistant primer/powder coating of not less

than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc

complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per

direction of Engineer-in- charge with glass of required thickness having 120

minutes of fire resistance both integrity & radiation control (EW120) and

minimum 20 minutes of insulation (EI20). The manufacturer have to give test

report/certification of fire glass and the glass should have the stamp showing

the value of E, EW & EI. The glass shall be tested in approved NABL

accredited lab or by any other accreditation body which operates in

accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for

testing and calibration scopes shall be eligible. The maximum glazing size

shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

TOTAL (Carried Over to Summary of Civil Works) 64,26,433.40 20,77,686.50

8.0 SUB HEAD 7- S T E E L WORKS

Structural steel work in single section, fixed with or without connecting plate,

8.1 10.1 including cutting, hoisting, fixing in position and applying a priming coat of 110.00 kg 86.05 9,465.50

approved steel primer all complete.

Structural steel work riveted, bolted or welded in built up sections, trusses

8.2 10.2 and framed work, including cutting, hoisting, fixing in position and applying a 120.00 kg 101.75 12,210.00

priming coat of approved steel primer all complete.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm

angle iron and 3 mm M.S. gusset plates at the junctions and corners, all

necessary fittings complete, including applying a priming coat of approved

8.3.1 10.5.1 Using M.S. angels 40x40x6 mm for diagonal braces 22.00 sqm 4,428.15 97,419.30

Providing and fixing T-iron frames for doors, windows and ventilators of mild

8.4 10.13 steel Tee-sections, joints mitred and welded, including fixing of necessary

butt hinges and screws and applying a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement

coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent

8.5 10.17 to shape with hooked ends in R.C.C. slabs or beams during laying, including 350.00 each 171.15 59,902.50

painting the exposed portion of loop, all as per standard design complete

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for

ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick

M.S. sheet with its top surface hacked for proper bonding, top lid shall be

screwed into the cast iron/ M.S. sheet box by means of 3.3mm dia. round

headed screws, one lock at the corners. Clamp shall be made of 12mm dia

M.S. bar bent to shape as per standard drawing.

Siganture of Bidder Page 13 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and fixing mild steel round holding down bolts with nuts and washer

plates complete.

Steel work welded in built up sections/ framed work including cutting,

hoisting, fixing in position and applying a priming coat of approved steel

primer using structural steel etc. as required.

In stringers, treads, landings etc. of stair cases including use of chequered

8.8.1 10.25.1 plate wherever required, all complete 4,504.50 kg 93.65 4,21,846.43

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar

Providing and fixing hand rail of approved size by welding etc. to steel ladder

8.9 10.26 railing, balcony railing, staircase railing and similar works, including applying

priming coat of approved steel primer.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,

channels, plates etc., including welding, grinding, buffing, polishing and

making curvature (wherever required) and fitting the same with necessary

stainless steel nuts and bolts complete, i/c fixing the railing with necessary

8.10 10.28 accessories & stainless steel dash fasteners , stainless steel bolts etc., of 456.00 kg 575.45 2,62,405.20

required size, on the top of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-in-charge, ( for payment purpose

only weight of stainless steel members shall be considered excluding fixing

accessories such as nuts, bolts, fasteners etc.).

TOTAL (Carried Over to Summary of Civil Works) 12,97,371.50

9.0 8 SUB HEAD 8 - FLOORING WORKS

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

9.1 11.3 aggregate) finished with a floating coat of neat cement, including cement

slurry, but excluding the cost of nosing of steps etc. complete.

9.1.1 11.3.1 40 mm thick with 20 mm nominal size stone aggregate 1,350.60 sqm 498.35 6,73,071.51

Chequerred precast cement concrete tiles 22 mm thick in footpath &

courtyard, jointed with neat cement slurry mixed with pigment to match the

shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick

bed of cement mortar 1:4 (1 cement: 4 coarse sand).

9.2.1 11.20.2 Medium shade pigment using 50% white cement 50% Grey cement 374.95 sqm 1,104.25 4,14,038.54

Kota stone slab flooring over 20 mm (average) thick base laid over and

jointed with grey cement slurry mixed with pigment to match the shade of

the slab including rubbing and polishing complete with base of cement

mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid

on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and

jointed with grey cement slurry mixed with pigment to match the shade of

the slabs, including rubbing and polishing complete.

Siganture of Bidder Page 14 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

40 mm thick fine dressed stone flooring over 20 mm (average) thick base of

cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with

cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment

to match the shade of stone.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:

15622 (thickness to be specified by the manufacturer), of approved make, in

all colours, shades except burgundy, bottle green, black of any size as

9.6 8.31 approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 2,297.21 sqm 1,030.30 23,66,815.46

12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white

cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm

or more (thickness to be specified by the manufacturer), of 1st quality

conforming to IS : 15622, of approved make, in colours White, Ivory, Grey,

Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4

Coarse sand), including grouting the joints with white ement and matching

pigments etc., complete.

Providing and laying heavy duty 15mm thick vitrified floor tiles in different

sizes (thickness to be specified by the manufacturer) with water absorption's

less than 0.08% and conforming to IS : 15622 of approved make in all

colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4

coarse sand) using spacers including grouting the joints with matching

including Grouting the joints of flooring tiles having joints with minimum 3-4

mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired

shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling /

grouting and finishing complete as per direction of Engineer-in-

charge.complete.

Providing and laying heavy duty 15mm thick vitrified s in different sizes

(thickness to be specified by manufacturer), with water absorption less than

9.9 NS3 0.08 % and conforming to I.S. 15622, of approved make, in all colours &

shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3

(1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm

Grouting the joints of flooring tiles having joints with minimum 3-4 mm width,

using epoxy grout mix of 0.70 kg of organic coated filler of desired shade

(0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting

and finishing complete as per direction of Engineer-in-charge.complete.

Providing and laying flamed finish Granite stone flooring in required design

and patterns, in linear as well as curvilinear portions of the building all

complete as per the architectural drawings with 18 mm thick stone slab over

20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse

sand) laid and jointed with cement slurry and pointing with white cement

slurry admixed with pigment of matching shade including rubbing, curing and

polishing etc. all complete as specified and as directed by the Engineer-in-

Siganture of Bidder Page 15 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye

Providing and laying Polished Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building all complete

as per the architectural drawings with 18 mm thick stone slab over 20 mm

(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid

and jointed with cement slurry and pointing with white cement slurry

admixed with pigment of matching shade including rubbing , curing and

polishing etc. all complete as specified and as directed by the Engineer-in-

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or

TOTAL (Carried Over to Summary of Civil Works) 98,59,707.98 91,96,214.51

10.0 9 SUB HEAD 9- ROOFING WORK

Providing and fixing on wall face unplasticised Rigid PVC rain water

pipesconforming to IS : 13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single

socketed pipes.

Providing and laying gola 75x75mm in cement concrete M15 grade

10.2 12.21 including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per 165.00 metre 237.25 39,146.25

standard design in 75x75 mm deep chase.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20

10.3 12.22 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 110.00 each 244.05 26,845.50

12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat

cement, rounding the edges and making and finishing the outlet complete.

Siganture of Bidder Page 16 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and fixing false ceiling at all height including providing and fixing of

frame work made of special sections, power pressed from M.S. sheets and

galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS :

277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with

flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed

to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia

bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of

required length with nuts & bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the

spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm

thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips

of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel with connecting clips made out of

2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and

30 mm long, the perimeter of ceiling fixed to wall/partition with the help of

rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm

interval, including fixing of gypsum board to ceiling section and perimeter

channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush finish of tapered and square edges

of the board with recommended jointing compound , jointing tapes , finishing

with jointing compound in 3 layers covering upto 150 mm on both sides of

joint and two coats of

primer suitable for board, all as per manufacturer's specification and also

including the cost of making openings for light fittings, grills, diffusers,

cutouts made with frame of perimeter channels suitably fixed, all complete

as per drawings, specification and direction of the Engineer in Charge but

excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-

(Part I) : 2011 (Board with BIS certification marks)

10.4.2 12-45-3 12.5 mm thick tapered edge gypsum moisture resistant board 494.10 sqm 1,286.20 6,35,511.42

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module

which includes providing and fixing 'C' wall angle of size 20x30x20 mm made

of 0.5 mm thick pre painted steel along the perimeter of the room with help

of nylon sleeves and wooden screws at 300 mm center to centre, suspending

the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from

the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12

10.5 12.54 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c.

Inverted triangle shaped Spring Tee having height of 24 mm and width of 34

mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in

direction perpendicular to it at 600 mm centers with help of suspension

brackets. Wherever the main C carrier and spring T have to join, C carrier

and spring T connectors have to be used. All sections to be galvanized @ 120

gms/sqm (both side inclusive), fixing with clip in tiles into spring T with :

Siganture of Bidder Page 17 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size

600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having

galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area

with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester

powder coated of thickness 60 microns (minimum), including factory painted

after bending and perforation.

TOTAL (Carried Over to Summary of Civil Works) 28,63,536.07

11.0 10 SUB HEAD 10 - FINISHING WORKS

11.1 13.1 12 mm cement plaster of mix :

11.2 13.2 15 mm cement plaster on the rough side of single or half brick wall of mix :

18 mm cement plaster in two coats under layer 12 mm thick cement plaster

1:5 (1 cement: 5 coarse sand) and a top layer 6mm thick cement plaster 1:3

(1 cement: 3 coarse sand) finished rough with sponge.

11.4 13.16 6 mm cement plaster of mix :

Extra for providing and mixing water proofing material in cement plaster work of 50kg

11.5 13.21 in proportion recommended by the manufacturers.Per bag of 50 kg cement cement 59.75

used in the mix used in

Extra for plastering exterior walls of height more than 10 m from ground level

for every additional height of 3 m or part thereof.

Providing and applying plaster of paris putty of 2 mm thickness over plastered

surface to prepare the surface even and smooth complete

11.8 13.33 Pointing on stone work with cement mortar 1:3 (1 cement: 3 fine sand) :

11.8.1 13.33.2 Raised and cut pointing Sqm 520.75

Distempering with oil bound washable distemper of approved brand and

manufacture to give an even shade :

New work (two or more coats) over and including water tinnable

11.9.1 13.41.1 priming coat with cement primer sqm 153.45

Finishing walls with textured exterior paint of required shade :

11.10 13.45 13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and 1,138.93 sqm 232.00 2,64,230.60

including priming coat of exterior primer applied @ 2.20kg/10 sqm

11.11 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including

priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of

required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade with

ordinary paint of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm,

11.13 13.80 of approved brand and manufacturer, over the plastered wall surface to sqm 115.15

prepare the surface even and smooth complete.

Siganture of Bidder Page 18 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic

Compound ) content less than 50 grams/ litre, of approved brand and

manufacture, including applying additional coats wherever required, to

achieve even shade and colour.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic

Compound ) content less than 50 grams/ litre, of approved brand and

manufacture, including applying additional coats wherever required, to

achieve even shade and colour.

Providing, supplying, installation and finishing with paint and putty of GRC

Screens (Jaali) of minimum thickness 50mm on façade as per drawing and

dimensions approved by Engineer In Charge including cost of M.S. framed

Structure required to mount the screens including all necessary hardwares.

TOTAL (Carried Over to Summary of Civil Works) 1,18,44,524.45 64,85,670.00

12.0 11 SUB HEAD 11 - ALUMINIUM WORKS

Providing and fixing aluminium work for doors, windows, ventilators and

partitions with extruded built up standard tubular sections/ appropriate Z

sections and other sections of approved make conforming to IS: 733 and IS :

1285, fixed with rawl plugs and screws or with fixing clips, or with expansion

hold fasteners including necessary filling up of gaps at junctions, at top,

12.1 21.1 bottom and sides with required PVC/neoprene felt etc. Aluminium sections

shall be smooth, rust free, straight, mitred and jointed mechanically wherever

required including cleat angle, Aluminium snap beading for glazing /

panelling, C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-charge. (Glazing and

panelling to be paid for separately) :

12.1.1 21.1.1 For fixed portion.

12.1.2 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) 7,206.30 kg 456.30 32,88,234.69

For shutters of doors, windows & ventilators including providing and fixing

hinges/ pivots and making provision for fixing of fittings wherever required

including the cost of PVC / neoprene gasket required (Fittings shall be paid

for separately).

12.2.1 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) 360.32 kg 546.35 1,96,858.10

Providing and fixing glazing in aluminium door, window, ventilator shutters

and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per

the architectural drawings and the directions of Engineer-in-charge . (Cost of

aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/

Siganture of Bidder Page 19 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and fixing double action hydraulic floor spring of approved brand

and manufacture conforming to IS : 6315, having brand logo embossed on

the body / plate with double spring mechanism and door weight upto 125 kg,

12.4 21.4 for doors, including cost of cutting floors, embedding in floors as required and

making good the same matching to the existing floor finishing and cover

plates with brass pivot and single piece M.S. sheet outer box with slide plate

etc. complete as per the direction of Engineer-in-charge.

12.4.1 21.4.1 With stainless steel cover plate minimum 1.25 mm thickness 157.00 each 2,412.50 3,78,762.50

Filling the gap in between aluminium frame, Upvc frame & adjacent RCC/

Brick/ Stone work by providing weather silicon sealant over backer rod of

approved quality as per architectural drawings and direction of Engineer-in-

charge complete.

12.5.1 21.8.1 Upto 5mm depth and 5 mm width 1,507.20 metre 79.45 1,19,747.04

Providing and fixing anodised aluminium (anodised transparent or dyed to

required shade according to IS: 1868. Minimum anodic coating of grade AC

15) sub frame work for windows and ventilators with extruded built up

standard tubular sections of approved make conforming to IS: 733 and IS:

1285, fixed with dash fastener of required dia and size (Dash fastener to be

paid for separately).

Providing and fixing anodised aluminium grill (anodised transparent or dyed

to required shade according to IS: 1868 with minimum anodic coating of

grade AC 15) of approved design/pattern, with approved standard section

and fixed to the existing window frame with C.P. brass/ stainless steel screws

12.7 21.17 @ 200 mm centre to centre, including cutting the grill to proper opening size kg 519.85

for fixing and operation of handles and fixing approved anodised aluminium

standard section around the opening, all complete as per requirement and

direction of Engineer-in-charge. (Only weight of grill to be measured for

Providing and fixing 12 mm thick frameless toughened glass door shutter of

approved brand and manufacture, including providing and fixing top & bottom

12.8 21.18 pivot & spring type fixing arrangement and making necessary holes etc. for 21.00 sqm 4,447.90 93,405.90

fixing required door fittings, all complete as per direction of Engineer-in-

charge (Door handle, lock and stopper etc.to be paid separately).

TOTAL (Carried Over to Summary of Civil Works) 49,86,808.79

13.0 SUB HEAD 12- WATER PROOFING WORKS

Providing and laying water proofing treatment to vertical and horizontal

surfaces of depressed portions of W.C., kitchen and the like consisting of :

(i) Ist course of applying cement slurry @ 4.4 Kg/Sqm mixed with water

proofing compound conforming to IS 2645 in recommended proportions

including rounding off junction of vertical and horizontal surface. (ii) IInd

course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with

water proofing compound in recommended proportion including rounding off 601.76 Sqm 705.70 4,24,663.57

junction of vertical and horizontal surface. (iii) IIIrd course of applying blown

or residual bitumen applied hot at 1.7 Kg. per Sqm of area. (iv) IVth course

of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be

100 mm wide and pasted to each other with bitumen @ 1.7 Kg/Sqm.)

Siganture of Bidder Page 20 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and laying integral cement based water proofing treatment

including preparation of surface as required for treatment of roofs, balconies,

terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement

admixed with water proofing compound conforming to IS. 2645 and approved

by Engineer-in-charge over the RCC slab including adjoining walls upto 300

mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to

115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand)

admixed with water proofing compound conforming to IS : 2645 and

approved by Engineer-in-charge over 20 mm thick layer of cement mortar of

mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge to required

slope and treating similarly the

adjoining walls upto 300 mm height including rounding of junctions

of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry

using 2.75 kg/ sqm of cement admixed with water proofing compound

conforming to IS : 2645 and approved by Engineerin- charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4

(1 cement :4 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineerin- charge including laying

glass fibre cloth of approved quality in top layer of plaster and finally finishing

the surface with trowel with neat cement slurry and making pattern of

300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum

period of two weeks for curing and for final test. All above operations to be

done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as 65

Providing and mixing integral crystalline admixture for water proofing

treatment to RCC structures like basement raft, retaining walls, reservior,

sewage & water treatment plant, tunnels / subway and bridge deck etc. at

the time of transporting of concrete into the drum of the ready-mix truck,

using integral crystalline admixture @ 0.80% (minimum) to the weight of

cement content per cubic meter of concrete) or higher as recommended by

the manufacturer’s specification in reinforced cement concrete at site of work.

The material shall meet the requirements as specified in ACI-212-3R- 2010

i.e. by reducing permeability of concrete by more than 90%, compared with

control concrete as per DIN 1048 and resistant to 16 bar hydrostatic

pressure. The crystalline admixture shall be capable of self-healing of cracks

up to a width of 0.50mm. The work shall be carried out all complete as per

specification and the direction of the Engineer-in-charge. The product

performance shall carry guarantee for 10 years against any leakage.

Siganture of Bidder Page 21 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and laying integral cement based treatment for water

proofing on the vertical surface by fixing specified stone slab 22 mm

to 25 mm thick with cement slurry mixed with water proofing

compound conforming to IS:2645 in recommended proportions with a

gap of 20 mm (minimum) between stone slabs and the receiving

surfaces and filling the gaps with neat cement slurry mixed with water

proofing compound and finishing the exterior of stone slab with

cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat

cement punning mixed with water proofing compound in

recommended proportion complete at all levels and as directed by

Engineer-in-charge :

Providing and laying integral cement based treatment for water

proofing on horizontal surface at all depth below ground level for

under ground structures as directed by Engineer-in-Charge and

consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and

specified rough stone slab over a 25 mm thick base of cement mortar

1:3 (1 cement : 3 coarse sand) mixed with water proofing compound

conforming to IS:2645 in the recommended proportion over the

leveling course (leveling course to be paid separately). Joints sealed

and grouted with cement slurry mixed with water proofing compound.

(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse

sand) mixed with water proofing compound in recommended

proportions. (iii) Finishing top with stone aggregate of 10 mm to 12

mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in

TOTAL (Carried Over to Summary of Civil Works) 50,70,206.04

14.0 DSR 2018 SUB HEAD 13: HORTICULTURE AND LAND SCAPING

Trenching in ordinary soil up to a depth of 60 cm including removal and

stacking of serviceable materials and then disposing of surplus soil, by

CPWD_HORT- spreading and neatly leveling within a lead of 50 m and making up the

2.1 trenched area to proper levels by filling with earth or earth mixed with sludge

or / and manure before and after flooding trench with water (excluding cost

of imported earth, sludge or manure).

Supplying and stacking sludge at site including royalty and carriage up to 5

km (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source, including

14.3 HORT-2.4 carriage up to 5 km Complete (manure measured in stacks will be reduced

by 8% for payment) :

14.4 HORT-2.4.1 Screened through sieve of I.S. designation 20mm 488.54 Cum 229.95 1,12,339.77

Spreading of sludge, dump manure and/or good earth in required thickness

14.5 HORT-2.8 as per direction of officer-in-charge (cost of sludge, dump manure and/ or 732.81 Cum 46.15 33,819.18

good earth to be paid separately). C

Siganture of Bidder Page 22 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Preparation of mounds of various size and shape by available excavated /

supplied earth in layers not exceeding 20 cm in depth, breaking clods,

watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m

complete as per direction of Officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of

14.7 HORT-2.57 unserveiceable material’s as per direction of officer in charge (excluding cost

of plant & water)

14.8 HORT-2.57.1 Trees Plant 78.00 Each 6.40 499.20

14.9 HORT-2.57.2 Shrubs Plant 304.00 Each 3.20 972.80

14.10 HORT-2.57.3 Hedge Plant 405.00 Each 2.15 870.75

14.11 CHAPTER 3.0 FOLIAGE AND SHADE LOVING PLANTS

Providing and displaying of Aglaonema Parrot Jungle plant (three in one),

having ht. 30 cm and above with 20 to 25 leaves, well developed, fresh &

healthy in 25 cm size of Earthen pot/ Plastic pot & as per direction of the

officer-in-charge.

Providing and displaying of Croton Petra Bangalore variety plant, having ht.

60 cm to 75 cm with 4 to 6 branches, well developed, fresh and healthy

colorful leaves in 25 cm size of Earthen pot/Plastic pot & as per direction of

the officer-in-charge.

Providing and displaying of Areca Palm having ht. 90 cm to 1.20 m with4 to 5

suckers, well developed, fresh and healthy with lush green foliagein 25 cm

size of Earthen pot/Plastic pot & as per direction of the officer-in-

SUB HEAD 4.0 SEASONAL PLANTS

Providing and Displaying of Allyssum white in full bloom well developed fresh

14.14 4.1 & healthy in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer- 34.00 Each 43.05 1,463.70

Providing and Displaying Asiatic lilly hybrid variety (3 in one) plants in each

14.15 4.6 pot having in full bloom 3 to 5 flowers 30 to 45 cm ht. well developed in 25 40.00 Each 129.15 5,166.00

cm Earthen ot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying Coleus broad leaves having 3 to 4 branches equal

14.16 4.20 well developed with fresh & healthy foliage in different colour in 25 cm 25.00 Each 54.35 1,358.75

Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

SUB HEAD 5.0 ORNAMENTAL PLANTS

Providing and Displaying Acalypha red well developed with fresh & healthy 30

14.17 5.3 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the 22.00 Each 41.00 902.00

officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry

palmar, Cherry Blossom etc. well developed with fresh & healthy bushy plant

in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the

officer-in-charge.

SUB HEAD : 6.0 GROUND COVERS PLANTS

Providing and stacking of Alpinia Variegated (three in one) having ht. 30

14.19 6.1 cmand above, with fresh and healthy variegated foliage in 25 cm size 80.00 Each 124.05 9,924.00

ofEarthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Siganture of Bidder Page 23 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and stacking of Asparagus marrie, well developed 15 to 20

14.20 6.3 leaves,full of branches and foliage in 25 cm size of Earthen Pot/Plastic Pot & 60.00 Each 56.40 3,384.00

asper direction of the officer-in-charge.

TOTAL SUB 7.0:TREE PLANTS

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in

big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Albizzia lebbek of height 150-165 cm. in bag of size

25 cm as per direction of the officer-in-charge.

Providing and stacking of Acacia auriculiformis of ht 150-165 cm in bag size of

25 cm as per direction of the officer-in-charge.

Providing and stacking of Mimusops elengi (Maulsri) of height 180-195 cm.,

14.24 7.59 well developed with thick stem in big in big size HDPE bag as per direction of 8.00 each 125.00 1,000.00

the officer-in-charge.

Providing and stacking of Mangifera indica (Mango-grafted ) of height 60-75

cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.

SUB HEAD 8.0:SHRUBS

Providing and stacking of Nyctanthes arbor-tristis (Hasingar) of ht. 90-105

cm in Earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Bauhinia acuminata height 60-75 cm. in earthen

pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3- 4

14.28 8.30 branches in earthen pots of size 20 cm as per direction of the officer-in- 65.00 Each 50.00 3,250.00

Providing and Displaying Topiary of Ficus Bush King well developed with fresh

& healthy foliage from Top to Bottom with single piller 60 to 75 cm spread,

210 to 225 cm ht., in 35 cm Cement Tray/Cement Pot as per direction of the

officer-in-charge.

Providing and Displaying Ficus Starlight with fresh, healthy and attractive

14.30 5.28 foliage 45 to 60 cm spread 75 to 90 cm ht., specimen bushy ,in 35 cm 34.00 Each 861.00 29,274.00

Cement Pot as per direction of the officer-in-charge

SUB HEAD 10.0: LAWN

Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm

thickness of existing ground prepared with proper level and ramming with

14.31 2.34 required tools wooden and than rolling the surface with light roller make the 3,382.75 Sqm 84.35 2,85,334.96

surface smoothen and light watering the same maintenance for 30 days or

more till the grass establish properly,as per direction of officer in charge

TOTAL (Carried Over to Summary of Civil Works) 11,96,892.34

15.0 SUB-HEAD 14 - ROAD WORKS

Siganture of Bidder Page 24 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete

from batching plant. The ready mixed concrete shall be laid and finished with

screed board vibrator , vacuum dewatering process and finally finished by

floating, brooming with wire brush etc. complete as per specifications and

15.1 16.75 directions of Engineer-incharge. (The panel shuttering work shall be paid for 155.00 Cum 8,663.05 13,42,772.75

separately). (Note:- Cement content considered in this item is @ 330

kg/cum. Excess/less cement used as per design mix is payable/ recoverable

Providing, laying and making kerb channel 30 cm wide and 50 mm thick with

cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate

15.2 16.63 20 mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size, 540.00 sqm 483.00 2,60,820.00

well rammed and consolidated and grouted with fine sand, including finishing

the top smooth etc. complete and as per direction of Engineer-in-charge.

Providing and laying 60mm thick faciory made cement concrete interlocking

paver block of M -30 grade made by block making machine with strong

vibratory compaction, of approved size, design & shape, laid in required

colour and pattern over and including 50mm thick compacted bed of coarse

sand, filling the joints with line sand etc. all complete as per the direction of

Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25

grade cement concrete in position to the required line, level and curvature

jointed with cement mortar 1:3 (1 cement : 3 coarse sand ) including making

joints with or without grooves (thickness of joints except at sharp curve shall

not to more than 5mm) including making drainage opening wherever

required complete etc. as per direction of Engineer-in-charge ( length of

finished kerb edging shall be measured for payment ). (Precast C.C. kerb

stone shall be approved by Engineer-in-charge).

Providing and laying matt finished vitrified tile of size 300x300x9.8mm having

with water absorption less than 0.5% and conforming to IS: 15622 of

approved make in all colours and shades in for outdoor floors such as

15.5 16.89 footpath, court yard, multi modals location etc., laid on 20mm thick base of 108.00 Sqm 1,264.80 1,36,598.40

cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns

including grouting the joints with white cement mixed with matching igments

etc. complete as per direction of Engineer-in-Charge.

TOTAL (Carried Over to Summary of Civil Works) 28,17,397.70

16.0 SUB-HEAD 15 - DRAINAGE

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of

16.1 19.19 required shape and approved quality 19.19.1 L D- 2.5

16.1.2 19.19.4.1 Circular shape 560 mm internal dia 10.00 each 1,859.50 18,595.00

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with

16.2 19.6 collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1

cement : 2 fine sand) including testing of joints etc. complete :

Siganture of Bidder Page 25 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. Description of Items QTY Unit Rate Amount (DSR) Amount (NDSR)

TOTAL (Carried Over to Summary of Civil Works) 1,31,762.50

Siganture of Bidder Page 26 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. DESCRIPTION OF ITEM DSR NSR

PLUMBING & FIREFIGHTING SYSTEM

I SANITARY FIXTURES 8,83,217.00 1,42,16,887.40

II SOIL, WASTE, VENT & RAIN WATER PIPES 17,230.00 43,75,409.00

III WATER SUPPLY 24,17,606.45 55,197.00

IV EXTERNAL WATER SUPPLY 2,49,634.50 -

V EXTERNAL SEWAGE AND STORM WATER 33,15,000.65 21,99,900.00

VI FIRE HYDRANT & ACCESSORIES 6,00,320.00 9,53,365.06

GRAND TOTAL 2,92,83,767

GRAND TOTAL 2,92,83,767

Plumbing Summary

Siganture of Bidder Page 27 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

1 SANITARY FIXTURES

Providing and fixing wall hung water closet

of approved shape & make including

providing & fixing concealed cistern with

dual flush fitting, of flushing capacity as per

the approved make, including seat cover,

and cistern fittings, nuts, bolts and gasket

etc complete. Make - KOHLER or Equalient

Make including Cistern, face plate, health

faucet etc., with all accessories etc.,

including making good walls, ledge wall,

core cutting (if any) etc., (BR-Rs.20,000/-)

Providing and fixing wash basin with C.I.

brackets, 15 mm dia CP Brass single hole

basin mixer of approved quality and make,

including painting of fittings and brackets,

cutting and making good the walls wherever

White Vitreous China Wash basin with a 15

1.2.1 a mm CP Brass single hole basin mixer Make -

1.2.2 b BASIN MODEL No. 25316IN-0

1.2.3 c MIXER MODEL No. 29928IN-4ND-CP

WASTE COUPLING : MODEL NO- 45432IN-

1.2.5 e BOTTEL TRAP : MODEL NO- 75823IN-CP

Providing and fixing Braided Hoses with

Two 15mm CP Brass Nuts & Rubber

Washers Without Nipple (Suitable for

Geysers and basins) of approved make :

Plumbing FF BOQ

Siganture of Bidder Page 28 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

1.3.1 a 45 cm length

1.3.2 b 15 mm nominal bore each 768 493.00 3,78,624.00

Providing and fixing toilet paper holder :

Providing,Fixing,testing and commissioning

1.5 NS-10 of CP brass coat hook with concealed each 157 1,196.00 1,87,772.00

Providing & fixing C.P. brass towel rail with

1.6 NS-11 C.P. brass wall brackets & C.P brass screws each 157 3,083.00 4,84,031.00

complete as required SIZE 600MM X200MM

Providing,Fixing,testing and commissioning

1.7 NS-12 of CP brass towel ring hook with concealed each 157 1,366.00 2,14,462.00

Providing and fixing C.P. brass shower

rose with arm and flange 15 or 20 mm inlet

Providing and fixing C.P. brass angle

1.9 NS-14 valve for basin mixer and geyser points of

approved quality conforming to IS:8931

(a) 15 mm nominal bore each 768 1,808.00 13,88,544.00

1.10 NS-15 Providing and fixing soap Dish. each 157 850.00 1,33,450.00

Providing and fixing horzontal/vertical Hot

water geyser made of MS body with

copper jacket inside with necessary inlet,

1.11 NS-16 outlet, drain, overflow, vent and all safety

accessories etc. complete including cutting

and making good the walls, wherever

a) 25 lit for Shower (Base Price Rs. 10,000) each 160 12,000.00 19,20,000.00

Plumbing FF BOQ

Siganture of Bidder Page 29 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Providing and fixing white vitreous china

with integrated sensor urinal shall have

pre & post flushing with water, having

1.12 NS-17 water inlet from back side, including fixing each 3 48,420.00 1,45,260.00

to wall with suitable brackets all as per

manufacturers specification and direction of

Engineer-in-charge.

Providing and fixing backlit mirror with all

desired fittings as per the approaved make

& model. Mirror of superior glass (of

approved quality) complete with 6 mm thick

1.13 NS-18 hard board ground fixed to wooden cleats each 160 3,725.90 5,96,144.00

with C.P. brass screws and washers

complete. Make - KOHLER Model NO -

23265IN or Equivalent

Providing and fixing C.P. brass/ SS long

nose bib cock of approved quality

conforming to IS standards and weighing

not less than 810 gms.

Providing and fixing C.P. brass/ SS stop

1.15 18.52 cock (concealed) of standard design and of

approved make conforming to IS:8931.

18.52.1 15 mm nominal bore(fr drinking area) each 4 606.25 2,425.00

Plumbing FF BOQ

Siganture of Bidder Page 30 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Supply installation testing and

commissioning water cooler having

nominal cooling capacity of 40 litres per

hours, with 100 litres storage tank with 2

nos. of faucets, one on goose neck type and

other one fountain type both with separate

mechanical lever control with 1.5 HP electric

motor for compressor to work on one phase

230 volts 50 Hz AC power supply with

complete assessories including cutting and

making wall as required.(Assume for

drinking points)

Supply installation testing and

commissioning water purifier comprising 5

micron filter and UV sterliser on cold water

1.17 NS-20 supply in drinking water cooler to work on Each 8 49,470.00 3,95,760.00

single phase 230 V 50Hz AC power supply

with capacity 120lph (Aquaguard

make)..(Assume for drinking points)

Providing and fixing Swing type Stainless

1.18 NS-21 steel Disabled Grab Bar of 32 mm Daimeter each 5 8,384.88 41,924.40

. Base price Rs.6200

Providing and fixing S.Steel Grab Rail

1.19 NS-22 600mm long 32mm dia complete in all each 5 2,028.60 10,143.00

respect. Base price Rs. 1500

Providing and fixing electrically operated

Stainless steel SS-304 hand sanitizer of

cpacity 2000ml complete in all respect

Base Price: Rs. 10,000

Plumbing FF BOQ

Siganture of Bidder Page 31 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

SOIL, WASTE, VENT & RAIN WATER

Providing and fixing Acoustic Multilayer

Polyproplene pipe including all necessary

fittings and special required as per EN 1451-

Part 1-6 with 3 layer pipe and one layer

fittings in PP MD, push-fit type,Halogen and

Cadmium free, having high impact

resistance as per DIN EN ISO 291:2008-08

, Ring stiffness SN6 6KN/m2 as per ISO

9969, offering sound levels of 19 dBA as per

EN 14366 at a flow rate of 4 l/s, water

2.1 NS-25 tightness as per EN 1451-1 minimum of 0.5

bar for 15 minutes, density of pipe = 1.2-

1.4 gms/cm3, elongation = 0.09mm/mn/K

and E modulus 2300-3000 as per ISO 178,

along with factory fitted EPDM lip ring, Fire

Behavior Classification according to EN

13501-1:2009 & classified D-s2-d2 (EN

13501-1), meets the requirements of EN

4102-2 with Fire Classification B2, Smoke

Development Category Q1 & Drip Formation

2.1.1 NS-25.1 32 mm nominal bore Metre 213 265.00 56,445.00

2.1.2 NS-25.2 40 mm nominal bore Metre 210 290.00 60,900.00

Plumbing FF BOQ

Siganture of Bidder Page 32 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Providing, fixing, jointing, testing and

commissioning UPVC (Class III) Rain water

down take pipe conforming to IS:4985 cut

to required lengths including all

necessary fittings and specials. Fixing at

wall/ceiling level supported by galvanized

steel clamps & hangers etc. Making

proper connection with cement solvent

joint as per BIS / manufacturer. Cutting,

chases / holes in floors / walls / slab.

Cutting holes up to 15x15 cm in R.C.C.

floors and roofs for passing drain pipe etc.

and repairing the hole after insertion of

drain pipe etc. with cement concrete 1:2:4

(1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size), including

finishing complete so as to make it leak

Providing and fixing hopper of PPE pipe

with two or three inlets fittings, connection

with saddle, to receive waste pipes from

fixtures waste.

Providing and fixing SS grating with frame

2.5 NS-28 including fixing to the floor with cement

Plumbing FF BOQ

Siganture of Bidder Page 33 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Providing & fixing of cast brass clean out

plug with suitable insert keys for opening

in: brass cap, male threaded joint with

threaded G.I socket fixed to HCI soil pipe or

C.I.(LA) pipe joints as required complete in

Providing and fixing floor drain points

formed out of 100 X 50mm dia reducing

elbow embedded in floor,all completein all

respect as directed.

Plumbing FF BOQ

Siganture of Bidder Page 34 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

III INTERNAL WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply,

including all CPVC plain & brass threaded

fittings, including fixing the pipe with

3.1 18.7 clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step

CPVC solvent cement and testing of joints

complete as per direction of Engineer in

Internal work - Exposed on wall

3.1.1 18.7.1 15 mm dia. nominal bore metre 241.55

3.1.2 18.7.2 20 mm dia. nominal bore metre 306.95

3.1.3 18.7.3 25 mm dia. nominal bore metre 369.20

3.1.4 18.7.4 32 mm dia. nominal bore metre 480.55

3.1.5 18.7.5 40 mm dia. nominal bore metre 648.60

3.1.6 18.7.6 50 mm dia. nominal bore metre 903.50

3.1.7 NS-31.1 65 mm dia. nominal bore metre 1,065.00

3.1.8 NS-31.2 80 mm dia. nominal bore metre 1,350.00

3.1.9 NS-31.3 100 mm dia. nominal bore metre 1,620.00

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply,

including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at

1.00 m spacing. This includes jointing of

3.2 18.8 pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and

making good the same including testing of

joints complete as per direction of Engineer

Concealed work, including cutting chases

and making good the walls etc.

Concealed work including cutting chases

and making good the wall.

Plumbing FF BOQ

Siganture of Bidder Page 35 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

3.2.2 18.8.2 20 mm dia nominal bore metre 240 478.15 1,14,756.00

Providing and fixing ball valve (brass) of

3.3 18.18 approved quality, High or low pressure, with

plastic floats complete

Providing and fixing gun metal gate valve

3.4 18.17 with C.I. wheel of approved quality

(screwed end) :

Painting G.I. pipes and fittings with

synthetic enamel white paint with two coats

over a ready mixed priming coat, both of

approved quality for new work :

3.5.5 18.38.5 40 mm diameter pipe meter 77 33.40 2,571.80

3.5.6 18.38.6 50 mm diameter pipe meter 88 39.80 3,502.40

3.5.7 NS-32.1 65mm diameter pipe meter 110 60.00 6,600.00

3.5.8 NS-32.2 80mm diameter pipe meter 405 83.00 33,615.00

3.5.9 NS-32.3 100mm diameter pipe meter 121 106.00 12,826.00

Supplying, fixing, testing and

commissioning of butterfly valve of PN 1.6

11(FIRE rating with bronze/gunmetal seat duly ISI

DSR) marked complete with nuts, bolts, washers,

gaskets conforming to IS 13095 of following

sizes as required

Plumbing FF BOQ

Siganture of Bidder Page 36 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Providing and fixing gun metal non- return

valve of approved quality (screwed end) :

3.7.1 18.19.1 25 mm nominal bore

3.7.4 18.19.2 32 mm nominal bore

Providing and fixing of approved make float

operated ball valve with Brass/copper

3.8 NS-33 heavy duty float confirming to IS 9762 & each 2 1,078.00 2,156.00

other associated accessories & works etc.,

complete. For 50 mm dia pipe

Providing and fixing proprietary polyshield

outer mechanical protection ON nitrile

rubber insulation comprising of wrapping

with poly glass tape helically wound and

subsequently applying 2 coats of polyshield

material (resin & hardner) as per

manufacturers specification and approved

by Project Manager / Consultants.

25 mm dia. nominal bore(19 mm thick

insulation)(assume for pantry.)

Plumbing FF BOQ

Siganture of Bidder Page 37 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

4 IV EXTERNAL WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply

including all CPVC plain & brass threaded

4.1 18.9 fittings This includes jointing of pipes &

fittings with one step CPVC solvent cement,

trenching, refilling & testing of joints

complete as per direction of Engineer in

Plumbing FF BOQ

Siganture of Bidder Page 38 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Constructing masonry Chamber

60x60x75cm, inside with 75 class

designation brick work in cement mortar

1:4 (1 cement : 4 fine sand) for sluice

valve, with C.I surface box 100mm. top

diameter,160 mm bottom diameter and 180

mm deep (inside) with chained lid and RCC

top slab 1:2:4mix (1 cement : 2 coarse

4.2 18.33 sand : 4 graded stone aggregate 20mm

nominal size) necessary excavation

foundation concrete 1:5:10 (1 cement : 5

fine sand : 10graded stone aggregate

40mm nominal size) and inside plastering

with cement mortat 1:3 ( 1cement :3

coarse sand) 12mm thick finished with a

floating coat of neat cement complete as

per standard design.

With common burnt clay F.P.S.(non

4.2.1 18.33.1 modular) bricks of each 5 9,288.40 46,442.00

class designation 7.5

Providing and fixing enclosed type water

meter (bulk type) conforming to IS : 2373

and tested by Municipal Board complete

with bolts, nuts, rubber insertions etc. (The

tail pieces if required will be paid

4.3.1 18.60.1 80 mm dia nominal bore each 2 3,576.10 7,152.20

Providing and fixing C.I. dirt box strainer for

bulk type water meter with nuts, bolts,

rubber insertions etc. complete conforming

SUB TOTAL - IV 2,49,634.50

Plumbing FF BOQ

Siganture of Bidder Page 39 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

EXTERNAL SEWAGE AND STORM

Excavating trenches of required width

for pipes, cables etc. including

excavation for sockets and dressing of

sides, ramming of bottoms, depth upto 1.5

M including getting out the excavated soil,

and then returning the soil as

required, in layers not exceeding 20

cms in depth including consolidating each

deposited layer by ramming, watering etc.

and disposing of surplus excavated soil as

directed, within a lead of 50 m. All kinds

Pipes, cables etc. exceeding 80 mm dia but

not exceeding 300 mm dia. Metre

Providing, laying and jointing glazed

stoneware pipes class SP-1 with stiff

5.2 19.1 mixture of cement mortar in the proportion

of 1:1 (1 cement : 1 fine sand) including

testing of joints etc. complete :

Providing and laying cement concrete

1:5:10 (1 cement : 5 coarse sand : 10

5.3 19.2 graded stone aggregate 40 mm nominal

size) all-round S.W. pipes including bed

concrete as per standard design :

5.3.1 19.2.1 100 mm diameter S.W. pipe Meter 50 999.15 49,957.50

Plumbing FF BOQ

Siganture of Bidder Page 40 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Providing and fixing square-mouth S.W.

gully trap class SP-1 complete with C.I.

grating brick masonry chamber with water

5.4 19.4 tight C.I. cover with frame of 300 x300 mm

size (inside) the weight of cover to be not

less than 4.50 kg and frame to be not less

than 2.70 kg as per standard design :

5.4.1 19.4.3. 180x150 mm size P type

5.4.2 19.4.3.2 With Sewer bricks conforming to IS : 4885 Each 65 2,413.65 1,56,887.25

Providing & Fixing HDPE (High Density

Polyethylene) pipes in accordance to IS

pressure (PE-80) & tempering (heat

reversion radial & axial dimension; < 0.6%

& <1.0% respectively) in accordance to DIN

8075, pipes wall thinckness as per EN-1519-

1 (Indicated on pipe). The pipes are

5.5 NS-34 manufactures allowing maximum operating

pressure condition of 20 C for 50 yrs,

including all HDPE fittings i/c fixing (As per

BS EN 12056, Part2) the pipe with clamps

at 5.00 m spacing. This includes the cost of

cutting,fusion welded (Electro Sleeve

Coupling or butt Welding ) and making

good the same complete as per direction of

Engineer in Charge.

Plumbing FF BOQ

Siganture of Bidder Page 41 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Constructing brick masonry manhole in

cement mortar 1:4 (1 cement : 4 coarse

sand) RCC top slab with 1:2:4 mix ( 1

cement: 2 coarse sand: 4 graded stone

aggregate 20 mm nominal size) foundation

concrete 1:4:8 mix (1 cement: 4

coarse sand: 8 graded stone aggregate

40 mm nominal size) inside plastering 12

mm thick with cement mortar 1:3 (1

cement: 3 coarse sand) finished with a

floating coat of neat cement making

channels in cement concrete 1:2:4 mix

(1 cement: 2 coarse sand: 4 graded

stone aggregate 20 mm nominal size)

finished with a floating coat of neat

cement complete as per standard design.

Inside size 90x80 cms and 45 cms deep

including CI cover with frame (Light

duty) 610x455mm internal diamesions

total weight of cover and frame to be not

less than 38 kg ( weight of cover 23 kg and

weight of frame 15 kg)

With common burnt clay F.P.S. (non

class designation 7.5

Inside size 120x90 cm and 90 cm deep

including C.I. cover with frame (medium

duty) 500 mm internal diameter, total

weight of cover and frame to be not less

than 116 kg (weight of cover 58 kg and

weight of frame 58 kg) :

With common burnt clay F.P.S. (non

modular) bricks of class designation 7.5

Plumbing FF BOQ

Siganture of Bidder Page 42 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Inside size 120x90 cm and 90 cm deep

including C.I.cover with frame (heavy duty)

560 mm internal diameter, total weight of

5.7 19.7.3 cover and frame to be not less than 208 kg

(weight of cover 108 kg and weight of

frame 100 kg) :

5.7.1 19.7.3.2 With Sewer bricks conforming to IS : 4885 Each 30 28,657.15 8,59,714.50

5.8 19.8 Extra for depth for manholes :

With common burnt clay F.P.S. (non

modular) bricks of class designation 7.5

With common burnt clay F.P.S. (non

modular) bricks of class designation 7.5

Constructing brick masonry circular type

manhole 0.91 m internal dia at bottom and

0.56m dia at top in cement mortar 1:4 (1

cement : 4 coarse sand), inside cement

plaster 12 mm thick with cement mortar

1:3 (1 cement : 3 coarse sand) finished

with a floating coat of neat cement,

5.9 19.9 foundation concrete 1:3:6 mix (1 cement :

3 coarse sand : 6 graded stone aggregate

40 mm nominal size), and making

necessary channel in cement concrete 1:2:4

(1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size) finished

with a floating coat of neat cement, all

complete as per standard design :

Plumbing FF BOQ

Siganture of Bidder Page 43 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

0.91 m deep with S.F.R.C. cover and frame

(heavy duty, HD-20 grade designation) 560

mm internal diameter conforming to I.S.

12592, total weight of cover and frame to

be not less than 182 kg., fixed in cement

5.9.1 19.9.1 concrete 1:2:4 (1 cement : 2 coarse sand :

4 graded stone aggregate 20 mm nominal

size) including centering, shuttering all

complete. (Excavation, foot rests and 12mm

thick cement plaster at the external surface

shall be paid for separately) :

With common burnt clay F.P.S. (non

modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91m

5.10 19.10 internal dia (at bottom) beyond 0.91 m to

With common burnt clay F.P.S. (non

modular) bricks of class designation 7.5

Constructing brick masonry circular

manhole 1.22 m internal dia at bottom and

0.56 m dia at top in cement mortar 1:4 (1

cement :4 coarse sand) inside cement

plaster 12 mm thick with cement mortar

1:3 (1 cement : 3 coarse sand) finished

with a floating coat of neat cement

5.11 19.11 foundation concrete 1:3:6 (1 cement : 3

coarse sand : 6 graded stone aggregate 40

mm nominal size) and making necessary

channel in cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size) finished

with a floating coat of neat cement, all

complete as per standard design :

Plumbing FF BOQ

Siganture of Bidder Page 44 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

1.68 m deep with SFRC Cover and frame

(heavy duty HD-20 grade designation) 560

mm internal diameter conforming to I.S.

12592, total weight of cover and frame to

be not less than 182 kg. fixed in cement

5.11.1 19.11.1 concrete 1:2:4 (1 cement : 2 coarse sand :

4 graded stone aggregate 20 mm nominal

size) including centering, shuttering all

complete. (Excavation, foot rests and 12

mm thick cement plaster at the external

surface shall be paid for separately) :

With common burnt clay F.P.S. (non

modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.22

5.12 19.12 m internal dia (at bottom) beyond 1.68 m

With common burnt clay F.P.S. (non

modular) bricks of class designation 7.5

Plumbing FF BOQ

Siganture of Bidder Page 45 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Providing orange colour safety foot rest of

minimum 6 mm thick plastic encapsulated

asper IS: 10910 on 12mm dia steel bar

conforming to IS :1786 having minimun

cross section as 23 mm x 25 mm and over

all minimum length 263mm and width as

165mm with minimum 112mm space

between protruded legs having 2mm tread

on top surface by ribbing or chequering

besides necessary and adequate anchoring

5.13 19.16 projections on tail length on 138mm as per each 99 463.05 45,841.95

standard drawing and suitable to with

stand the bend test and chemical

resistance test as per specifications and

heaving manufacture"s permanent

identification mark to be visible even after

fixing " incluting fixing in manholes with

30x20x15 cm cement concrete block 1:3:6:

(1 cement :3 coarse sand :6 graded stone

aggregate 20mm nominal size )complete as

Making connection of drain or sewer line

with existing manhole including breaking

into and making good the walls, floors with

cement concrete 1:2:4 mix (1 cement : 2

coarse sand : 4 graded stone aggregate 20

mm nominal size) cement plastered on both

sides with cement mortar 1:3 (1 cement : 3

coarse sand) finished with a floating coat of

neat cement and making necessary

channels for the drain etc complete.

5.14.1 19.21.2 For pipes 250 to 300 mm diameter Each 6 717.30 4,303.80

Plumbing FF BOQ

Siganture of Bidder Page 46 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Constructing brick masonry road gully

chamber 50x45x60 cm with bricks in

cement mortar 1:4 (1 cement : 4 coarse

sand) including 500x450 mm pre-cast

R.C.C. horizontal grating with frame

complete as per standard design.

With common burnt clay F.P.S. (non

class designation 7.5

Providing and laying S&S C.I. standard

5.16 18.25 specials such as tees, bends, collars, tapers,

caps etc. (Heavy class):

Providing and laying S&S centrifugally cast

5.17 18.27 (spun) iron pipes (Class LA) conforming to

Plumbing FF BOQ

Siganture of Bidder Page 47 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Grease separator EasyClean Underground

NS 4, Standard, 550-950 mm, class A/B for

underground installation

according to EN1825

• Resistant when installed in the

groundwater up to 500 mm

• A load distribution plate must be provided

Upper section made of polymer, infinite

height and level adjustment,

with cover class A/B in accordance with EN

124 made of cast iron,

sealed odour-tight, incl. lift-out key

Inlet/Outlet: 110 mm

Sludge trap capacity: 400 l

Total separator capacity: 770 l

Fat storage: 120 l

Certification: Z-54.1-440

Dimension: 1380 x 1106 mm

5.18.1 NS-35.1 Make : KESSEL

NS-35.2 Seawage pumping Sump Pumps :

Providing and fixing submersible pumps

for suitable rating, with non-clog free flow

open CI impeller,CI casing, SS-410 shaft

, Pumps shall be provided with lifting

chain. Pump should be capable on

operation on 415

Volts ± 10 % 50 HZ A.C 3 phase supply.

The above pump sets must be supplied

complete with following accessories.

Complete piping with common delivery upto

Plumbing FF BOQ

Siganture of Bidder Page 48 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Necessary cables from pump set to control

Electrical switch panel having all necessary

accessories & safety devices of standard

specifications. (Panels with sump pumps

near each sump as per site conditions). --1

Automatic built-up water level controller

with necessary length of cable upto control

C.I Butterfly valve (PN-1.0) ( 2 Nos.)

C.I. Dual plate check valves (PN-1.0) ( 2

Capacity: 10.0 m3/hr

Head : 15 Metre

KW : 1.5 (Approx.) or as required.

Solid handling : 10 to 12 mm

Quantity : 2 Nos. (1W+1SB) Each 1 75,000.00 75,000.00

Plumbing FF BOQ

Siganture of Bidder Page 49 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

6 VI FIRE PROTECTION SYSTEM

Hydrants, Piping & Accessories

Providing, laying, jointing, testing and

commissioning of following sizes of m.s.

pipes conforming to IS-1239 with all

accessories like all fittings (for pipes upto

50mm dia threaded forged steel fittings and

for pipes above 50 mm dia GI fitting with

welded joint shall be used) including tees,

elbows, reducers, union, flanges, rubber

gaskets, GI nuts bolts, washer including

supporting/fixing the pipe on

floor/wall/ceiling with clamps, hangers

(using anchor fastners) as per specification.

Providing two coats of synthetic enamel

paint of approved shade over two coats of

primer. Prior to application of primer the

surface should be cleaned for any dirt,

rusts, rough substance etc. Including

painting of legends both direction arrow as

per the approval of the Project Manager.

GIpipe sleeve of suitable higher size shall

be provided wherever the pipes are crossing

the walls / floors and sealing the sleeves

with glass wool in between & fire sealent

compound at either end all as per Project

Manager’s requirements iits labs as per

ISO/IEC 17025 for testing and calibration

scopes shall be eligible. The maximum

glazing size shall not be more t

Plumbing FF BOQ

Siganture of Bidder Page 50 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

All hangers, clamps, brackets etc. shall be

of galvanized iron unless specified

otherwise and the supply of the same shall

also be included in rates under this head.

Welding of any kind on the galvanized

support / hanger shall not be permitted.

MS `C' Heavy class pipe

Providing and fixing ball valve (brass) of

6.2 18.18 approved quality, High or low

pressure, with plastic floats complete :

Providing, fixing, testing & commissioning

of butterfly valve (PN 1.6) (suitable for

test pressure of 24 kg / sqcm) with flanges,

nut bolts, gaskets, painting and necessary

pad locking arrangement complete

Supplying and fixing first-aid Hose Reel with

MS construction spray painted in post office

red, conforming to IS 884 complete with the

following as required.

20 mm nominal internal dia water hose

6.4.1 thermoplastic (Textile reinforced) type -2 as

20 mm nominal internal dia gun metal

globe valve & nozzle.

Drum and brackets for fixing the equipmets

Plumbing FF BOQ

Siganture of Bidder Page 51 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Connections from riser with 25 mm dia stop

gun metal valve & M.S. Pipe and socket.

Providing and fixing in position the

6.5 16.8 industrial type pressure gauges with gun No 22.00 1,094.00 24,068.00

metal / brass valves complete as required

Providing, fixing, testing & commissioning

of automatic Air release valve with 15mm

dia stop cock, flanged inlet connection,

pressure gauge with gun metal stop cock

complete with all accessories as required

and conforming to IS IS : 12992 (Part 1).

Providing, fixing, testing & commissioning

of indoor type hose lockable cabinet

frames fabricated from 40 x 40 x 5 angle

iron sections and 16 gauge MS sheet with

full front glass door and locking

arrangement, suitable to accommodate

landing valves, 15 m long hoses, first-aid

6.7 NS-37 hose reel and branch pipe nozzle & fire

mans’ axe. The cabinet frame shall be

painted with one coat of primer and two or

more coats of synthetic enamel paint of

approved make and shade, as required

(Approx 2.1 m (high) x 0.9 m (wide). The

item shall be complete of MS housing with

(Cost shall be inclusive of providing break

glass box containing key for the cabinet No. 18 22,172.00 3,99,096.00

along with hamer).

II Portable Chemical Fire Extinguishers

Plumbing FF BOQ

Siganture of Bidder Page 52 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Supply, installation, testing and

commissioning of following types of

extinguisher with provision of wall bracket

(fixed with anchor fastner).

Providing & fixing ISI marked portable

chemical fire extinguisher, water (gas

pressure) type capacity 9 litres

6.8.1 NS-38.1 conforming to IS: 15683:2006 with gun No. 18 2,206.00 39,708.00

metal cap and nozzle and complete in all

respects including initial fill and wall

suspension brackets

Providing & fixing ISI marked

(IS:15683:2006) portable CO2 type fire

extinguisher type 4.5 kg capacity.

Including valve, discharge hose of not less

6.8.2 NS-38.2 than 10 mm dia & 1 M long complete in all No. 18 13,854.00 2,49,372.00

respects including initial filled with CO2 gas

confirming to IS:307-1966 & filled to a

filling rate of not more than 0.667 and wall

suspension bracket.

Providing & fixing of ABC Type, Portable

Fire Extinguisher, dry powder type (Gas

Cartridge) conforming to IS: 15683 : 2006

with cylinder initially fully charged with dry

powder, ISI marked confirming to IS:15683

: 2006 complete with standard discharge

valve with tube, CI bracket for wall

FIRE PUMPS AND EQUIPMENTS

Supply, installation, testing and

6.8.4 NS-39 commissioning of terrace fire pump

comprising of the following:

Plumbing FF BOQ

Siganture of Bidder Page 53 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S.No. DESCRIPTION OF ITEM UNIT QTY. RATE

Horizontal mono-block centrifugal pump,

suitable for operation on 415 volts ± 6%, 3

phase, 50 HZ A.C supply.

The pump casing shall be CI, shaft shall be

CS & impeller / shaft sleeve / casing

wearing ring shall be bronze. The system

shall be complete with necessary pressure

gauge with gun metal shut off cock on

delivery side. (The pump should meet the

condition and shall be gotten approved by

the Local fire Authority).

Squirrel cage induction motor TEFC type for

operation on 415 V, 3 phase 50 HZ AC

supply for the above pump with speed of

Suitable cement concrete foundation with

plaster, (design and drawing to be provided

by the Contractor while the foundation will

be done by others) complete with

Antivibration arrangement of cushy foot

For pump defined above & of duty as

TOTAL CARRIED TO SUMMARY 6,00,320.00 9,53,365.06

Plumbing FF BOQ

Siganture of Bidder Page 54 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

Sr No Description Unit Quantity Rate Amount

Supply, Installation, Testing & Commissioning of Variable Refrigerant Volume

(VRV/ VRF) modular type airconditioning system complete with Indoor and

Outdoor Unit and accessories ; Outdoor unit should be aircooled, 100% scroll

compressor invertor technology based, microprocessor controlled, using eco

friendly R410A refrigerant; Variable refrigerant temperature control (Outdoor

Unit) and variable air volume control (Indoor Unit) at different load conditions

; Each Outdoor Unit module of mimimum 14HP and above should be of

multiple (minimum two) circuit, and shall be capable of performing both

cooling as well as heating function suitable for operation on 415+/- 10%-

DSR Item Volts, 50 Hz. 3 Ph AC supply ; Shall comprise of scroll compressor and

1 2019 aircooled condenser and fan with motor; first charge of refrigerant and oil,

1.0 vibration isolation pads, interconnecting joints between various modules of

Outdoor Units, MS Stand with two coats of primer and one coat of enamel,

accessories as required and complete in all respect.Before prequrement

vender has to take approval over the ckt degin. The Invertor Compressor

should be on-line type, it should start first at minimum frequency to prevent

inrush of starting current. Outdoor Unit should have minimum ESP of 78Pa for

effective heat dissipation/ extensive arrangement, should be capable of

performance upto 49 degree ambient. The Outdoor Unit should have function

of controlling evaporative refrigerant temperature to avoid cold draft,

excessive cooling and for better energy efficiency.

1.1 1.0.1 Outdoor Units (VRV)

1.2 NSH-1 Indoor Units (VRV) -

Supply, Installation, Testing & Commissioning of 4 way Cassette type Indoor

Unit , sophisticated decoration panel with 360 degree airflow, with filter and

with motorised louvres, 3 step airflow control, Dx type, electronic control

1.2.1 valve, dual suction fan, statically and dynamically balanced , cooling coils of -

seamless copper tubes, cleanable type filters with anti-mould and acti-

bacterial treatment , drain pump, PID Control, fixtures and supports complete

in all respect, of following capacities :

Siganture of Bidder Page 55 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

Sr No Description Unit Quantity Rate Amount

Supply, Installation, Testing & Commissioning of High Wall type Indoor Unit ,

sophisticated decoration panel with filter and with motorised louvres, 3 step

airflow control, Dx type, electronic control valve, dual suction fan, statically

1.2.3 and dynamically balanced , cooling coils of seamless copper tubes, cleanable -

type filters with anti-mould and acti-bacterial treatment , drain pump, PID

Control, fixtures and & supports complete in all respect, of following

Supply, Installation, Testing & Commissioning of high wall split unit with

Indoor & outdoor Units 5 star inverter, copper compressor, sophisticated

decoration panel with 360 degree airflow, with filter and with motorised

louvres, with remote, 3 step airflow control, Dx type, electronic control valve,

dual suction fan, statically and dynamically balanced , cooling coils of

1.2.3 NSH-2 seamless copper tubes, cleanable type filters with anti-mould and acti- -

bacterial treatment , drain pump, PID Control, fixtures and supports

complete, with remote in all respect, of following capacities:

Minimum air moving capacity of units as mentioned below to be

maintanined and higer size / multiple units to be selected to meet the

dehumidified air quantity.

1.2.3.a NSH-2.1 2.0 TR (minimum air moving capacity 750 to 800 cfm) Nos 85 65,625.00 55,78,125.00

1.2.3.b NSH-2.2 1.5 TR (minimum air moving capacity 480 to 530cfm) Nos 80 54,010.00 43,20,800.00

Supply , Installation, Testing & Commissioning of Remote controllers

suitable for above indoor units to operate, monitor, ON/OFF, temperature

setting, 3 step air flow changing etc. The remote controller shall be corded

type suitable for wall mounting with bracket

1.3.1 NSH-3.1 Remote Controller No 20 1,700.00 34,000.00

1.3.2 Central Controller for Indoor & Outdoor Units -

Supply, Installation, Testing & Commissioning of Central Controller (I-Touch

Manager) with Touch Screen type and capable of controlling of all IDUs and

ODUs complete with necessary hardware, adaptor, accessories etc. to

perform the following functions:

Control of IDUs, ODUs Units as above with monitoring of vital parameters

such as temperature sensing & setting, ON/OFF, status etc.

ii) Permit / prohibit function of Each remote controlled unit -

iii) Operation of units in individually or in group -

iv) Display of floor plans to enable quick search of desired units -

v) Operation history of units -

vi) Filter status of indoor units with alarm -

vii) Fault indication with Alarm -

Siganture of Bidder Page 56 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

Sr No Description Unit Quantity Rate Amount

Energy management through monitoring the energy consumption data

and identifying inefficient operations

To perform energy saving control i.e. to restrict capacity of IDUs incase power

consumption exceed the set limit.

x) Provision of Integration with BMS system & transfer of data -

Integration with Fire alarm & security system (the units will be switched off in

case of activation of fire alarm)

The central controller will be complete including all hardware &

(excluding wiring) suitable to perform above function.

Supply, installation, testing & commissioning of Interconnecting copper

refrigerant pipe of size 16 Gauge upto 19.1 mm O.D and below this 20 Gauge

work with (19 mm / 13 mm thick) closed cell elastomeric nitrile rubber

tubular insulation between each set of indoor & outdoor units as per

manufacturer's specifications, all piping shall be properly supported,

complete in all respect :

NSH-4.1 34.9 mm O.D.(insulation : 13 mm) Rmt 30 1,170.00 35,100.00

NSH-4.2 28.6 mm O.D.(insulation : 13 mm) Rmt 30 1,108.00 33,240.00

NSH-4.3 22.2 mm O.D.(insulation : 13 mm) Rmt 10 865.00 8,650.00

NSH-4.4 19.1 mm O.D.(insulation : 13 mm) Rmt 10 707.00 7,070.00

NSH-4.5 15.9 mm O.D.(insulation : 13 mm) Rmt 20 588.00 11,760.00

NSH-4.6 12.7 mm O.D.(insulation : 13 mm) Rmt 20 466.00 9,320.00

NSH-4.7 9.5 mm O.D.(insulation : 13 mm) Rmt 120 300.00 36,000.00

NSH-4.8 6.4 mm O.D.(insulation : 13 mm) Rmt 120 225.00 27,000.00

Supply and installation of control cum transmission wiring of copper in

suitable size of 2Cx1.5sqmm/2.0sqmm as per manufacturer's specification in

MS conduit along with terminations lugs, glands, tagging etc. complete in all

Supply and installation of UPVC piping complete with fittings, supports as per

4 NSH-6 specifications and duly insulated with 13 mm thick nitrile rubber insulation, -

complete in all respect :

Supply, fabrication, erection and commissioning of factory fabricated

rectangular ducts using G.I Sheets.The price shall include TDF flanges,

turning vanes, supports, sealent (neoprene gasket), hangers, access door

etc., complete in all respect :

5.1 NSH-7.1 24 gauge galvanized sheet steel (0.63mm) Sqmt 300 942.00 2,82,600.00

Supply, fabrication, installation and testing of the flexible connections

6 NSH-8 constructed out of fire resistant double canvas sleeve for cabinet type fans, Nos 16 2,450.00 39,200.00

complete in all respect :

Siganture of Bidder Page 57 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

Sr No Description Unit Quantity Rate Amount

Supply, installation and testing of 18 G GSS construction opposed blade

volume control dampers complete with brass bush & operating handles within

7 NSH-9 ducts to be provided with suitable links, levers and quadrants for manual Sqmt 6 7,250.00 43,500.00

control of volume of air flow and for proper balancing of the air , complete in

8 Air Registers -

Supply,installation,testing & balancing of 150x150 mm aluminium powder

8.1 NSH-10 coated air grilles for toilet exhaust with all sides flanged, complete in all Sqmt 14 6,400.00 89,600.00

Supply, Installation, Testing & Commissioning of extruded aluminium powder

coated Pantry and Toilet Air Door Grille, complete in all respect :

Supply and installation of rectangular Cabinet type direct driven Inline Fans

9 NSH-12 for Mechanical Ventilation Of Toilet, supports, bird screen at exhaust, -

complete in all respect :

Supply, installation, testing and commissioning of fusible link fire damper as

per UL 555 listed complete with all accessories.

Total (Supply, Installation, Commissioning & Ancillary Work Of VRV

Airconditioning System & Mechanical Ventilation Of Toilets)

Siganture of Bidder Page 58 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

DSR 2018 NON SCHEDULED TOTAL

SL. NO. DESCRIPTION

AMOUNT AMOUNT (DSR + Non-DSR)

D ELECTRICAL WORKS

SUB HEAD-I: WIRING &

SUB HEAD -II: DISTRIBUTION

3 Head III : LIGHTING FIXTURES 1,25,250.00 12,19,860.00 13,45,110.00

4 SUB HEAD - IV : UPS WORK 4,00,000.00 4,00,000.00

5 SUB HEAD- VII -MV PANELS 23,59,846.00 23,59,846.00

SUB HEAD-VIII : CABLE Tray ,

Cables & END TERMINATIONS

SUB HEAD-IX :EARTHING & LA

Sub Head - X External Lighting

9 Fire Detection System 21,51,366.00 21,51,366.00

11 CCTV & Access control system 6,65,500.00 6,65,500.00

12 Solar & EPABX system 34,50,000.00 34,50,000.00

13 Lift Works 33,00,000.00

Total for Electrical Works 1,47,08,549.00 1,30,76,421.00 2,77,84,970.00

Total Electrical Works 2,77,84,970.00

Electrical Summary

Siganture of Bidder Page 59 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

Sr No DSR /NS Description Unit Quantity Rate Amount

A NSL-1 TECHNICAL SPECIFICATIONS FOR PASSENGER LIFTS For Hostel 13 PAX

Number of Landings(i.e. Stops) 3 (All openings on same side). Travel Height 12 mtr Capacity 1020 kg approx or as per lift

manufacture Passengers 15 no. Speed1.0mps MotorTypeGearless

Hoistway Size available (Clear)2500 mm (W) x 3000 mm (D)Floor Markings G, 1, 2, Overhead in mm 4800 mm Pit Depth

in mm 1650 mm Drive System & Control Alternating Current Voltage Frequency (ACVF) with Closed Loop system Operation

Full Collective –Duplex Car Size ( WxDxH) 1600 mm (W) x 1500 mm (D) x 2250 mm (H) Car door (Height x Width)mm

Minimum 1000 (Width) x 2100 (Height) Car /Ceiling SS- Finish with Spot LED Lighting Car Walls Finish SS hairline

Car Floor Recess of 20mm Mirror, Sill Aluminium profiles Car Operating Panel To Be furnished

Car Lighting Minimum 150 lux on floor and on Car operating Panel. Handrail, SS Finish on the rear wall Decoration Skirting

& Corners Must be Anodised for weather protection Landing Door Size (WxD)mm Minimum 1000 (Width) x 2100 (Height)

Main Entrance Landing Door SS-Hairline FInish. Other landing doors are SS Hairline finish. Landing Door control system

1 NSL-1 Fully Automatic Control & Fixtures Details - Common for all Elevators Landing display Centre Opening Sliding Door-

Stainless Steel etched finish.,16-segment Car position and direction of travel display and Lift under maintenance display

Emergency Alarm Main Floor Over load warning Audio/Visual Overload warning indicator to be provided.Braile Buttons On

COP & LOP Car Display 16-segment LED Dynamic Car Direction display & Digital position indicators Infra-red Light Curtain

(Full Length) on Car doors To be provided Auto Light/Fan Cutoff Ventilation fan ON OFF switch with auto switch off feature

Door open/ Door Close Door open and Door Close buttons with Symbol markings.

ARD operation indication in car To be provided Emergency Alarm Button Emergency Alarm button with Bell symbol & the

same should be at a distinct distance from the call buttons. Intercom To be provided (i.e. 3-way intercom) Hall Buttons To

be provided as per the Tenderer Out of Service Mode To be provided Attendant Operation To be provided Potential free

contacts BMS Controller Machine & Drive System - Common for all Elevators Power Supply 3 x 415V /220V, 50 Hz

Acceptable Voltage Fluctuation +10% to -15% Acceptable Frequency Fluctuation +/- 5% Rate of Acceleration/Deceleration

M/s2 < 0.5 meter per second square Jerk( m/sec3) < 1 meter per second cube Vibrations Horizontal Vibration X/Y (mPtP)

Airborne Noise level in Car (without Fan) 50 ± 3 dBa Airborne Noise level at landing door Operation Max 60 dBa Airborne

Noise level in front of closed Hoistway door (when car passing by) Max 53 dBa Stopping Accuracy ± 5mm Elongation ±

20mm Leveling Accuracy ± 10mm Door Drive Compact VVVF closed loop Car panel & Door panel thickness Atleast 1.5 mm

Maximum Number of trips Per Hour < 180 Safety Features & Other Inclusions --- Common for all Elevators Door Protection

Multi beam infrared protection device so as to reverse the closing door in case of slight obstruction in the door way. Anti

nuisance To Be provided Fire Man Control To be Provided Over Load detection Device To be provided Buffers Spring Buffers

Safety Governor Electro-Mechanical type Safety governors for Car.Safety Instructions Do’s & Don’ts with emergency Each 2 ₹ 16,50,000.00 ₹ 33,00,000.00

contact Numbers must be provided & displayed in the car Over travel protection Terminal and final limit switches to be

provided. Controller / Drive / Motor Protection Trip Device for Over current, Under Voltage and Over voltage than the rated

capacity. + 10% Motor overload / over torque Instantaneous over current • Ground fault Under voltage

Over voltage – 3 phase • Output & Input phase loss • Phase reversal • Output short circuit • Over

speed • Spikes & Surges Protection with the Sudden surges/spikes in level in voltage alongwith shifting of neutral and

earth leading to improper earthing Must be provided as a separate kit. ARD ( Automatic Rescue Device)ARD to be provided.

(Detailed Literature of Make and working of ARD to be provided separately).

Siganture of Bidder Page 60 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

Fire Rating of Landing doors Landing doors must have 2 hour fire resistance rating and Elevator supplier must provide the

Fire-certificate for the same from Accrediated laboratory. Self adjustment & self Daigonastic To be provided Intercom

connection Must be provided in 3-way Fascia Plates & Sill angles Full height Fascia Plates and Sill angles to be provided (As

per the IS Code Guidelines)

Pit Ladder MS Pit ladder to be provided and securely fastened inside the pit. Counter Weights

In case of non-metallic filler weights, the counterweight sections shall be totally enclosed in a metallic covering. Hand Rails

SS Hairline finish Hand rails at Rear side. All Hand rails to be fixed at a height of 900mm from the floor level. Infra-red

Light Curtain (Full Length) on Doors

To be provided. Multi beam infrared protection device so as to reverse the closing door in case of slight obstruction in the

door way. Elevators Uptime & Connectivity The manufactuer must ensure the maximum uptime of the elevators for which

elevator must be provided with the in-built device to capture the data like door movement or lifecycle utilization are

collected, pre-analyzed, and transmitted to the Cloud Platform which could be access online from any-where.

Traction Medium PVC grooved Belt with Ahead system Associated Civil and structural items

All civil and structural items of work associated with erection and operation of lifts shall be provided by the Contractor at

his cost including (but not restricted to ) the following. Scaffolding and safety barricades for erection in and around lift

hoist ways Buffer supports Ladder in pits with 2 safety switches Safety railing on top of car Channels, separators,

stretchers etc. Sill angles ascia Plates Minor Builders Work Environmental Conditions at Site of installation a) Summer:

480 C (RH-25%) b) Winter: 40 C (RH-80%) Storage space provided Not Available Is neutral wire available for control

Yes Circuits Proposed date for commencement on As per civil work Sitee) Lift in use/ lift out of order sign A suitable box

above the lift landing with LED illuminated bilingual (in English & Hindi) sign of “LIFT OUT OF ORDER” coming up

simultaneously at all floors

Siganture of Bidder Page 61 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

CONSTRUCTION OF 300 BEDDED HOSTEL AT DR KSSR, NEW DELHI

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

INTERNAL ELECTRICAL WORK

1.0 1 SUB HEAD-I: WIRING & SUBMAIN

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in surface /

1.0 1.10 recessed medium class PVC conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC

insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/fan point/exhaust

fan point/ call bell point (without independent switch etc.) with

2.0 1.5 sq. mm FRLS PVC insulated copper conductor single core

cable in surface/ recessed PVC conduit, and earthing the point

with 1.5 sq. mm FRLS PVC insulated copper conductor single

core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following

3.0 1.14 sizes of FRLS PVC insulated copper conductor, single core cable in surface/

recessed medium class PVC conduit as required.

3.6 1.14.8 4 X 4 sq. mm + 2 X 4 sq. mm earth wire Metre 1 308.00 308.00

3.7 1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire Metre 1 394.00 394.00

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6

4.0 1.56 A modular socket outlet and 2 nos. 5/6 A Each 2 582.00 1,164.00

modular switch, connections etc. as required. (For light plugs to be used in

non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover

in front on surface or in recess, including providing and fixing 3 pin 5/6

5.0 1.31 amps modular socket outlet and 5/6 amps modular switch, Each 1175 401.00 4,71,175.00

connection etc. as required. (For light plugs to be used in non residential

Supplying and fixing suitable size GI box with modular plate and cover in

6.0 1.32 front on surface or in recess, including providing and fixing 6 pin 5/6 & Each 260 495.00 1,28,700.00

15/16 amps modular socket outlet and 15/16 amps modular

switch, connection etc. as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/

wooden block including connection etc as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2

pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB,

8.0 2.18 in sheet steel enclosure, on surface or in recess, with chained metal cover each 219 1,232.00 2,69,808.00

for the socket out let and complete with connections, testing and

commissioning etc. as required.

Siganture of Bidder Page 62 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

Supplying and fixing 20/25 A, 415 V, TPN Industrial type socket outlet, with

4 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, TPMCB,

9.0 2.19 in sheet steel enclosure, on surface or in recess, with chained metal cover each 2 1,690.00 3,380.00

for the socket out let and complete with connections, testing and

commissioning as required.

Supplying and fixing following modular switch/ socket on the existing

8 1.24 modular plate & switch box including connections but excluding modular

plate etc. as required.

8.1 1.24.7 TV antenna socket outlet EACH 15 126.00 1,890.00

Supplying and fixing following size/ modules, GI box alongwith modular

9 1.27 base & cover plate for modular switches in recess etc. as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper

11 1.19 conductor PE insulated, shielded with fine tinned copper braid and protected Mtrs 500 33.00 16,500.00

with PVC sheath in the existing surface/ recessed steel/ PVC conduit as

Supplying and fixing of following sizes of medium class PVC conduit along

12.0 1.21 with accessories in surface/recess including cutting the wall and making

good the same in case of recessed. conduit as required.

TELEHONE AND DATA SYSTEM

Supplying and drawing following pair 0.5 mm dia FRLS PVC

13 1.18 insulated annealed copper conductor, unarmored telephone

cable in the existing surface/ recessed steel/ PVC conduit as

Supplying and fixing of telephone distribution board (tag block) in hinged

15 NS - 1 type MS box duly powder coated complete with bakelite sheet with Nos 2 3,500.00 7,000.00

termination of incoming and outgoing telephone wire etc. complete as

Supplying and fiixing 2 pin Telephone modular socket & switch with

16 1.24 modular plate,suitable size metal box and sheet cover including

connection, testing, etc. as required.

16.1 1.24.6 Telephone socket with shtter outlet Each 175.00 119.00 20,825.00

Siganture of Bidder Page 63 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

Supplying and fixing following size/ modules, GI box alongwith

17 1.27 modular base & cover plate for Tel/ Data in recess etc.

19 NS-2 Supplying and fixing 1 nos of CAT-6 , I/O Each 325.00 105.00 34,125.00

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing

surface/ recessed Steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

21.0 1.21 conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Item as stated above Rs.

Total of Sub-Head - I carried to summary sheet 97,39,074.00 34,125.00

2 SUB HEAD -II: DISTRIBUTION BOARD

Supplying and fixing following way, single pole and neutral, sheet steel,

MCB distribution board, 240 V, on surface/ recess, complete with tinned

2.3 copper bus bar, neutral bus bar, earth bar, din bar, interconnections,

powder painted including earthing etc. as required. (But without

MCB/RCCB/Isolator)

2.3.2 8 way , Double door Each 2 1,760.00 3,520.00

Supplying and fixing following way, horizontal type three pole and neutral,

sheet steel, MCB distribution board, 415 V, on surface/ recess, complete

1.0 2.4 with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But

without MCB/RCCB/ Isolator)

12 way ( 4 + 36 ) Double Door, with separted phase wise 2 pole RCCB

provision is required 1,97,750.00

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,

3.0 2.10 miniature circuit breaker suitable for inductive load of following poles in the

existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required.

Supplying and fixing following rating, four pole, 415 volts, MCB in the

5.0 existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing following rating, double pole, (single phase and

neutral), 240 volts, residual current circuit breaker (RCCB), having a

6.0 2.14 sensitivity current upto 300 milliamperes in the existing MCB DB complete

with connections, testing and commissioning etc. as required.

Siganture of Bidder Page 64 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

Total of Sub-Head - II Carried to summary sheet 3,96,481.00 2,63,390.00

Sub-Head - III: LIGHTING FIXTURES

1 Supply of Fixtures :

1.1 NS- 5 20 Watt LED 4 ft Tube Light Each 575.00 300.00 1,72,500.00

Downlight Deep Receesed/surface Panel 12w 3000K Complete with LED

1.3 NS - 7 Bulk Head Fixture 9 watt Each 25.00 750.00 18,750.00

Supply and installation of 300mm, 230V A.C exhaust fan in the existing

1.11 NS- 8 opening including making good the damage connection testing Each 6.00 1,500.00 9,000.00

commissioning etc as required

Supply and installation of 9W - LED Bollard as per engg. Incharge selection

Glaze fitted with low glare diffuser.

Supply and installation of 9W LED Bush Light as per engg. Incharge

NS- 8.3 selection in die-cast aluminium housing with high quality toughened glass Each 40.00 4,320.00 1,72,800.00

Supply and installation of 30W - LED post top Lantern as per engg.

Incharge selection with low glare optical design acrylic diffuser.

NS-8.5 Electrical Illuminated Fire Exit Sinages Each 10.00 2,400.00 24,000.00

2 Erection of Fixtures:

Installation, testing and commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/

LED lamps per fitting, complete with all accessories including

connections etc. as required.

Installation of exhaust fan in the existing opening, including

1.3 1.50 making good the damage, connection, testing, commissioning Each 2.00 150.00 300.00

etc. as required.

Sub-Head - III: LIGHTING FIXTURES Rs. 1,25,250.00 12,19,860.00

SUB HEAD - IV : UPS WORK

Siganture of Bidder Page 65 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

Supplying, installation, testing and commissioning of online 3

phase UPS System with 30 minutes back up including batteries,

interconnecting cables, battery racks etc. Details as bellow :

Item Specification:-

1) Micro Processor Controlled 40 kVA UPS system with

battery backup for 60 mins.

2) UPS Rating – 2 kVA

PLINTH 3) Input : 415 VAC 3 Phase

AREA 4) Output :230 VAC 3 Phase

RATES 5) Ambient Temperature : 45 °C (Average)

FOR 6) Relative Humidity: 95% PER

2.1 SPECIAL 7) Backup : 60 Mins at Full-Load 20.00 20,000.00 4,00,000.00

ISED 8) UPS should have static & maintenance bypass with static

WORKS 9) UPS should have a DC ground facility also.

DSR-4 10) Display: A) LCD Display for parameters like Input supply

voltage, current, frequency, Output supply voltage, current,

frequency, Bypass volt, current, frequency, ambient

temperature, DC volt, inverter tune. B) LED Display for

On/Off/Fault, status for Input

supply/Rectifier/Battery/Inverter.

11) Recovery time < 10 milliseconds

Sub head - IV UPS system 4,00,000.00

Sub Head - V : Electrical Panels

1.2 Distrubution Panels

Design, fabrication, assembling, wiring, supply,installation, testing and

commissioning of Main LT panel / Main distribution panels / sub-

distribution panels, fabricated out of 14 gauge CRCA sheet steel in cubicle

compartmentised modular 3b construction, free standing floor mounted,

dust and vermin proof with reinforcement of suitable size angle iron,

channel, `T’ sections and / or flats wherever necessary. 16 gauge CRCA

sheet steel shall be used for final distribution panels. 3 mm thick cable

gland plates shall be provided on top as well as at the bottom of the panels.

Panels shall be treated with all anticorrosive process before powder coating

as per specifications and final approved shade. 2 Nos. earthing terminals

shall be provided for all distrtibution panels. Panels shall be suitable for

415V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall also be

provided in case of large panels. Approval shall be taken for each panel in

the form of shop drawings before fabrication.

Incoming Supply - 1 ( From Existing Transformer supply )

Siganture of Bidder Page 66 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

1000 Amps 4 Pole manually operated fully drawout type air circuit breaker

with ON/OFF/TRIP indicating lumps with MCB's and over current short

circuit and earth fault microprocessor releases (Type 2A of MG or equivalent

Multi Function Meter (Conzerve – EM 6400 with RS485 port or equivalent)

of accuracy class-I, with 3 Nos. 1000/5 amps 15VA CT - 1 Set

Phase indicating light shall be protected by 2 Amps MCB’s. - 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Breaker control switch - 1 Set

Auto-manual selector switch - 1 Set

Auxiliary contacts required for necessary interlocking of breakers.

Incoming supply - 2 ( From Existing DG set )

400 Amps 4 Pole MCCB with ON/OFF/TRIP indicating lamps with MCB's and Nos 1 10,70,846.00 10,70,846.00

over current short circuit and earth fault microprocessor releases () - 1 set.

Multifunction meter (Conzerve – EM 6400 with RS485 port or equivalent)

of accuracy class-I, with 3 Nos. 400/5 amps 15VA CT - 1 Set

Phase indicating light shall be protected by 2 Amps MCB’s. - 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Breaker control switch - 1 Set

Auto-manual selector switch - 1 Set

Auxiliary contacts required for necessary interlocking of breakers.

1200 Amps TPN aluminium bus bars with colour coded heat shrinkable

insulating sleeves - 1Set

Note:- Both incommer shall be elecrically and Mechnically

400 amps TP+N MCCB. - 1 No.

315 A TPN MCCB - 1 No

Siganture of Bidder Page 67 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

250 amps TP+N MCCB. - 2 Nos.

160 amps TP+N MCCB. - 3 Nos.

63 amps TP+N MCCB. -4 Nos.

Spare Feeders - 400A TPN MCCB - 1 No

125 A TPN MCCB - 1 No

Siganture of Bidder Page 68 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

63 A TPN MCCB - 2 Nos

NS - 9 Main LT Panel

2 MDB - 1 ( Light & Power Panel )

400 Amps TP+N MCCB with following accessories:

Digital electronic VAF meter with and 400/5 Amps 5 VA, CL 1 CTs . - 1 Set

Phase indicating light shall be protected by 2 Amps SP MCB's. -3 Set.

600 Amps TPN aluminium bus bars with heat shrinkable insulation sleeve. -

250 A TPN MCCB - 2 Nos

200 A TPN MCCB - 2 Nos

100 A TPN MCCB - 3 Nos

63A 4 Pole MCB - 12 Set

40 A 4 pole MCB - 2 Set

63 A 4 pole MCB - 2 Nos

All MCCB’s shall be of 25 KA breaking capacity. Nos 1 2,00,000.00 2,00,000.00 2,00,000.00

All MCB’s shall be of 10 KA breaking capacity.

NS - 10 MDB - 1 ( Light & Power Panel )

3 SDB - 1 & 2 ( Light & Power Panel )

200 Amps TP+N MCCB with following accessories:

Digital electronic VAF meter with and 200/5 Amps 5 VA, CL 1 CTs . - 1 Set

Phase indicating light shall be protected by 2 Amps SP MCB's. -3 Set.

315 Amps TPN aluminium bus bars with heat shrinkable insulation sleeve. -

63A 4 Pole MCB - 8 Set

80 A 4 Pole MCB - 8 set

63 A 4 pole MCB - 4 Nos

All MCCB’s shall be of 25 KA breaking capacity. Nos 2 1,50,000.00 3,00,000.00

All MCB’s shall be of 10 KA breaking capacity.

11 NS - 11 SDB - 1 & 2 ( Light & Power Panel )

4 MDB - 2 ( HVAC Panel )

250 Amps TP+N MCCB with following accessories:

Digital electronic VAF meter with and 250/5 Amps 5 VA, CL 1 CTs . - 1 Set

Siganture of Bidder Page 69 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

Phase indicating light shall be protected by 2 Amps SP MCB's. -3 Set.

300 Amps TPN aluminium bus bars with heat shrinkable insulation sleeve. -

63A TPN MCCB - 6 Set

63 A TPN MCCB - 2 Nos

All MCCB’s shall be of 25 KA breaking capacity. Nos 1 1,60,000.00 1,60,000.00

All MCB’s shall be of 10 KA breaking capacity.

12 NS - 12 MDB - 2 ( HVAC Panel )

5 MDB -3 (Kitchen panel)

160 Amps TP+N MCCB with following accessories:

Digital electronic VAF meter with and 160/5 Amps 5 VA, CL 1 CTs . - 2 Set

Phase indicating light shall be protected by 2 Amps SP MCB's. -6 Set.

200 Amps TPN aluminium bus bars with heat shrinkable insulation sleeve. -

63 A 4 Pole MCB - 6 Nos

63A 4 Pole MCB with 63 A 4 Pole RCCB of 30mA - 2 No.

40A 4 Pole MCB with 40 A 4 Pole RCCB of 30mA - 2 No.

Spare MCB’s of the following :

63 A 4 Pole MCB - 1 No.

40 A 4 Pole MCB - 1 No.

All MCCB’s shall be of 25 KA breaking capacity. Nos 1 71,500.00 71,500.00

All MCB’s shall be of 10 KA breaking capacity.

13 NS - 13 MDB -3 (Kitchen panel)_described as above

6 MDB - 4 (UPS O/G Panel )

100 Amps TP+N MCCB with following accessories:

Digital electronic VAF meter with and 100/5 Amps 5 VA, CL 1 CTs . - 1 Set

Phase indicating light shall be protected by 2 Amps SP MCB's. -3 Set.

Siganture of Bidder Page 70 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

150 Amps TPN aluminium bus bars with heat shrinkable insulation sleeve. -

63A 4 pole MCB = 3 Set

40 A 4 pole MCB - 3 set

63 A 4 Pole MCB - 2 Nos

All MCCB’s shall be of 25 KA breaking capacity. Nos 1 57,500.00 57,500.00

All MCB’s shall be of 10 KA breaking capacity.

14 NS - 14 MDB - 4 (UPS O/G Panel )

7 150 KVAR CAPACITOR AUTOMATIC CONTROL PANEL

1 No. 315 Amps TP+N MCCB with following accessories:

VAF digital electronic meter with inbuilt selector switch and 400/5 Amps

suitable VA, CL 1 CTs . - 1 Set

Phase indicating light shall be protected by 2 Amps SP MCB’s. - 3 Sets

Power factor compensating relay (including power factor meter) in 8 steps

for automatic cut off or add on capacitor units to keep the power factor at

0.97 with variation of loads. All associated auxiliary contactors / relays /

timer / auto manual selector switches to be provided - 1 Set.

400 amps TPN Aluminium bus bars with coloured heat Shrinkable insulated

sleeves. - 1 set

Outgoing feeders consisting of following accessories.

40 amps TPN MCCB -2 Set

40 amps or capacitor duty 440 volts 50Hz contactors. - 2 Sets

“ON” /”OFF” push buttons and indicating lamps. - 2 Sets

12.5 KVAR Mixed heavy duty MPP capacitor unit with 7% dutune filtor as

specified - 2 No.

Outgoing feeders consisting of following accessories.

80 amps TPN MCCB -3 Set

Siganture of Bidder Page 71 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

70 amps or capacitor duty 440 volts 50Hz contactors. - 3 Sets

“ON” /”OFF” push buttons and indicating lamps. - 3 Sets

25 KVAR Mixed heavy duty MPP capacitor unit with 7% dutune filtor as

specified - 4 Nos

All MCCB’s shall be of 35 KA breaking capacity.

Capacitor automatic control panel (150 KVAR) as described

8 Transformer Isolator Panel

1000 Amps 4 Pole manually operated fully drawout type air circuit breaker

16 NS - 16 with ON/OFF/TRIP indicating lumps with MCB's and over current short Each 1 2,05,000.00

circuit and earth fault microprocessor releases (Type 2A of MG or equivalent

DG Isolator Panel ( I/C 400 A MCCB Micro processor with RYB &

ON/OFF/Trip ) with complete encloser

Sub Head - V ( Electrical Panels ) 23,59,846.00

Perforated trays

Supplying and installing following size of perforated painted with powder

coating M.S. cable trays with perforation not more than 17.5%, in

18 4.1 convenient sections, joined with connectors,suspended from the ceiling with

M.S. suspenders including bolts & nuts, painting suspenders etc as

18.1 4.1.7 600 mm width X 50 mm depth X 1.6 mm thickness Mtr 75 765.00 57,375.00

18.1 4.1.6 450 mm width X 50 mm depth X 1.6 mm thickness Mtr 50 700.00 35,000.00

18.1 4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness Mtr 165 621.00 1,02,465.00

18.1 4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness Mtr 250 531.00 1,32,750.00

18.1 4.1.1 100 MM width x 50 mm depth x 1.6 mm thickness Mtr 100 476.00 47,600.00

Siganture of Bidder Page 72 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

19 Supply of MV cable

Supply, following sizes of PVC sheathed XLPE insulated Aluminium

conductor multicore control armoured cable of 1.1 KV grade.

19.1 NS - 19 3.5C x 95 sq mm Aluminium Metre 150 451.00 67,650.00

19.1 NS - 21 4C x 25 sq mm Aluminium Metre 150 178.00 26,700.00

19.1 NS - 22 4C x 16 sq mm Aluminium Metre 1750 116.00 2,03,000.00

19.1 NS - 23 4C x 10 sq mm Aluminium Meter 300 115.00 34,500.00

Supplying and making end termination with brass compression gland and

aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

20 9.1 aluminium conductor cable of 1.1 KV grade as required.

20.8 9.1.32 4C x 10 sq mm Aluminium

Laying of one number PVC insulated and PVC sheathed / XLPE

21 7.6 power cable of 1.1 KV grade of following size direct in ground

including excavation, sand cushioning, protective covering and

refilling the trench etc as required.

21.2 7.6.2 Above 35 sq. mm and upto 95 sq. mm Mtr 150 38.00 5,700.00

SUB HEAD - VI Cable Tray & Cables

SUB HEAD-IX :EARTHING SYSTEM + LA System

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

22 5.4 including accessories, and providing masonry enclosure with Set 20 6,216.00 1,24,320.00

cover plate having locking arrangement and watering pipe of

2.7 meter long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including

accessories, and providing masonry enclosure with cover plate having

locking arrangement and watering pipe of 2.7 metre long etc. with

charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for

connections etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300

26 6.2 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick nos 6 448.00 2,688.00

G.I. base plate including holes etc. complete as required.

Siganture of Bidder Page 73 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

S. Amount in Rs. Amount in Rs.

2018 Description Unit Qty. Rate

No. (Schedule Items) (Non- Schedule Items)

Fixing of lightning conductor finial (single prong) with base plate including

holes etc. complete as required.

28 6.7 Providing and fixing G.I. tape 20 mm X 5 mm thick on parapet or surface of RM 600 104.00 62,400.00

wall for lightning conductor complete as required.(For horizontal run)

29 6.8 Providing and fixing G.I. tape 20 mm X 5 mm thick on parapet or surface of RM 300 163.00 48,900.00

wall for lightning conductor complete as required.(For vertical run

30 6.9 Fixing of copper/ G.I. tape 20 mm X 5 mm thick on parapet or surface of RM 600 65.00 39,000.00

wall for lightning conductor complete as required.(For horizontal run)

31 6.1 Fixing of copper/ G.I. tape 20 mm X 5 mm thick on parapet or surface of RM 300 131.00 39,300.00

wall for lightning conductor complete as required.(For vertical run)

Total of Sub-Head - IX carried to summary sheet 7,22,814.00

Sub Head - X External Lighting System ( Land scape )

1. SITC of External Landscape Bollard Lights ( 9 watt LED ) with complete

2. SITC of 3c x 2.5 sq mm Copper Ar cable for external Light Fixtures

33 NS - 26 3. SITC of external Feeder Pillar for External Light Fixtures Nos 2 20,000.00 40,000.00

Total of Subhead - X carried to summery sheet 9,15,000.00

Siganture of Bidder Page 74 of 82 Signature of NBCC

Construction of 300 Bedded Hostel at Dr KSSR, New Delhi

Sl.No 2018 Description UNIT Qty Unit Price (Rs.) Total (Rs.)

1 ADDRESSABLE TYPE FIRE DETECTION SYSTEM

Supplying, installation, testing and commissioning of micro

processor based intelligent addressable main fire alarm

panel, central processing unit with the following loop

modules and capable of supporting not less than 240 devices

(including detectors) and minimum 120 detectors per loop

and loop length up to 2 km, network communication card,

minimum 320 character graphics/ LCD display with touch

screen or other keypad and minimum 4000 events history log

in the non volatile memory (EPROM), power supply unit (230

± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed

maintenance free batteries with automatic charger. The

panel shall have facility to connect printer to printout log and

facility to have seamless integration with analog/digital voice

evacuation system (which is part of the schedule of work

under SH: PA System) and shall be complete with all

accessories . The panel shall be compatible for IBMS system

with open protocol BACnet/ Modbus over IP complete as per

specifications.

2 17.2.4 Supplying, installation, testing & commissioning of intelligent

addressable thermal detector with rate of rise cum fixed

tempreature thermistor complete with base as required. (Smoke

3 17.2.7 SITC of Fault Isolator complete with Base as required Nos 10 3257.00 32,570.00

4 17.2.5 Supplying, installation, testing & commissioning response

indicator on surface/recess MS box having two LEDs metallic Nos 15 263.00 3,945.00

cover complete with all connections etc. as required.

5 17.2.14 Supplying, installation, testing & commissioning of

addressable manual call point complete as required.

6 17.2.15 Supplying, installation, testing & commissioning of

addressable horn cum strobe complete as required.

7 17.2.10 Supplying, installation, testing & commissioning of

addressable control/Monitor Module complete as required.

8 17.2.11 Supplying, installation, testing & commissioning of

addressable Phone control Module complete as required.

9 17.2.17 Supplying, installation of Fire Fighter Hand set

addressable Phone control Module complete as required.

10 17.5.1 Supply & Iaying of 2 x 1.5 sq mm Fire Survival Copper Ar cable (

600/1000 V ) with LSZH inner & outer sheet & steel wire Rm 3500 328.00 11,48,000.00

armouring complete as required

Item as stated above Rs. 21,51,366.00

Siganture of Bidder Page 75 of 82 Signature of NBCC