SPECIAL REPAIR TO BLDG NO P-15 (OTM ACCN) IN SAJJAN LINE AT UDAIPUR MIL STN

Amount

Taking down chowkats or frames with shutter (without taking off shutters from frames) n. exc 1.50 Sqm each, complete all as specified and as directed.

Taking down chowkats or frames with shutter (without taking off shutters from frames) exc 1.50 Sqm but n. exc 4 Sqm each, complete all as specified and as directed.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each after easing and adjusting complete all as specified and as specified.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing of debris to out side of MD land from site, complete all as specified and as directed.

Dismantling floor /wall tiling of any description including cement mortar bedding / backing coat and removing of rubbish to out side of MD land from site, complete all as specified and as directed.

Material & Labour for Non - skid light coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

Material & Labour for double charged (premium quality) light coloured vitrified tiles of size 600 mm x 600 mm x 8 to 10 mm thick in floors etc. set and jointed in neat cement slurry and inted in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Supply and fixing double charged (premium quality) light coloured vitrified tiles of size 600mm x 100mm, 8-10mm thick as in skriting set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM (1:4), complete all as specified.

Material & Labour for light colored glazed ceramic tiles of size 600x300x7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick cement plaster in ement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed.

Material and labour for machine cut Kota stone slab 18-22 mm thick (of size not less than 55 cm x 55 cm in flooring and 120 cm x 25 cm in treads) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including half round edge moulding, over and including cement screed bed 15 mm thick in cement mortar (1:6) base including rubbing and mirror polishing, complete all as specified.

Material & Labour for machine cut Kota stone slab 18-22 mm thick (of length not less than 55 cm in skirting and 120 cm in risers) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in vertical surfaces such as skirting and risers over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces, complete all as specified.

Material & Labour for Green Marble work 16-18 mm thick (table rubbed and polished) in steps, riser, skirting, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces complete all as specified and directed.

Material & Labour for Granite work (Jet black/Telephonic black) 16-18mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces complete all as specified and directed.

Material & Labour for 25 mm thick PCC 1:2:4 type B-0 (12.5 mm graded aggregate), in sub base of flooring etc, complete all as specified and directed.

Material and labour for 50mm thick, PCC 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregate) as in plinth protection/PCC path, and paving, finished the surface even and fair without using extra cement, laid in alternate bays, complete all as specified.

Providing & Fixing factory made 100% solid WPC (wood polymer composite) door frame 90 mm x 45 mm (moulded) single rebated 32 mm x 15 mm to receive shutter of 30 - 35 mm thickness made from wood polymer composite (Single Extruded process) material comprising of virgin PVC polymer of K value 57-60 (suspension grade) calcium carbonate and Natural fibres (wood powder / rice husk / wheat husk) and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body traded and headed screw having minimum frame dencity of 780 kg/cbm, having good screw holding capacity (screw withdrawal strength of (min990N), minimum compressive strength of 58 N/sqmm, Modulus of elasticity 900 N/sqmm and resistance of spread of flame of class A category with properity of being termite /berer froo, water/ Moisture Proof & fire retardent & fixed in position with SS Dash Fasteners / Hold Fast of require dia and length, all as per specifications drawing as directed by Engr - in - charge. Material test certificate and authentication should be compulsory provided by manufacturing company. Make:- Rajshree door / Syntex/ Fenesta Note: Hold fast and Dash Fastners are included in rate quoted.

Providing & Fixing factory made 100% solid WPC (wood polymer composite) Door Frames of cross section 125 mm x 65 mm having double rebate of 32 mm x 15 mm to receive shutter of 30 - 35 mm thickness (moulded) single rebated made from wood polymer composite (Single Extruded process) material comprising of virgin PVC polymer of K value 57-60 (suspension grade) calcium carbonate and Natural fibres (wood powder / rice husk / wheat husk) and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body traded and headed screw having minimum frame dencity of 780 kg/cbm, having good screw holding capacity (screw withdrawal strength of (min990N), minimum compressive strength of 58 N/sqmm, Modulus of elasticity 900 N/sqmm and resistance of spread of flame of class A category with properity of being termite /berer froo, water/ Moisture Proof & fire retardent & fixed in position with SS Dash Fasteners / Hold Fast of require dia and length, all as per specifications drawing as directed by Engr - in - charge. Material test certificate and authentication should be compulsory provided by manufacturing company. Make:- Rajshree door / Syntex/ Fenesta Note: Hold fast and Dash Fastners are included in rate quoted.

Material & Labour for providing PCC 1:3:6, type C-0 (using 12.50 mm graded stone aggregate) as in filling of pressed steel door frame and holdfasts including necessary formwork etc.

Supply and fixing framed work as in doors or gates or framework for water tanks of angle or other section with gussest plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering doors etc, to be prepared for hanging and sliding with and including either hooks and hinges or steel hnging door fittings and fixing complete confirming to gde Fe 290 (Gde E-165)

Material & Labour for 35mm thick factory made ASCU vacuum pressure treated kiln seasoned IInd class hard wood plain framed panel shutter (two panels or more) with lock rails and panel of 9mm thick B.W.P. commercial ply or 12mm veneered particle board with commercial veering on both faces. The size of rail and style as per I.S. 1003(Part-I) 2001, complete all as specified and directed.

Supply and fixing IInd class (hollock) factory made 35mm thick glazed skelton shutters (minimum 4 panels), open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge prepared to slide horizontally on beads including Supply and fixing bead etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.

Providing & Fixing toilet door frame, factory made 100% solid WPC (wood polymer composite) door frame 90 mm x 45 mm (moulded) single rebated 32 mm x 15 mm to receive shutter of 30 - 35 mm thickness made from wood polymer composite (Single Extruded process) material comprising of virgin PVC polymer of K value 57-60 (suspension grade) calcium carbonate and Natural fibres (wood powder / rice husk / wheat husk) and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body traded and headed screw having minimum frame dencity of 780 kg/cbm, having good screw holding capacity (screw withdrawal strength of (min990N), minimum compressive strength of 58 N/sqmm, Modulus of elasticity 900 N/sqmm and resistance of spread of flame of class A category with properity of being termite /berer froo, water/ Moisture Proof & fire retardent & fixed in position with SS Dash Fasteners / Hold Fast of require dia and length, all as per specifications drawing as directed by Engr - in - charge. Material test certificate and authentication should be compulsory provided by manufacturing company. Make:- Rajshree door / Syntex/ Fenesta Note: Hold fast and Dash Fastners are included in rate quoted.

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm Moulded prelam colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply & fixed 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed.

Supply and fixing 100 mm long stainless steel butt hinges with galvanised MS hinge pin etc.

Supply & fixed 150 mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified.

Supply and fixing 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified.

Supply & fixed MS Spring Hing 100 mm long fixed with screws to wooden/CPVC chowkhats or fixed with welding to steel chowkhats.

Supply & fixed steel windows box type ERW hollow 'P' section comprising double frame for and including gauged and glazed skelton shutter 30mm thick jointed internally with flat iron 25x3mm complete including hinges handle tower bolts, stops lugs,grill etc all as shown in drawing as applicable complete all as specified and directed. Note :- For the purpose of measurement & payment double shutter with frame and grill shall be considered as one unit. (ii) Glazing,wire mesh & painting shall be measured & paid separately.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or galvanised wire staples (to be fixed upto four storey of bldgs) complete all as specified and directed.

Supply & fixed for sheet glass 3mm thick, ordinary quality and glazing with oil putty, in square n.exc 0.5 Sqm each and glazing with oil putty to steel window complete all as specified.

Supply and fixing Aluminium anodised or powder coated door, window, ventilator frame with one or more rebates and shutter sliding or casement windows as reqd. including jointing cleat, glazing clips with EDP gasket for fixing, rubber packing etc, complete all as specified and directed.

Supply & fixed for poder coated aluminium grill of 7.00mmx3mm thick section square, rectangular, triangular, circular shape aperture not exc 7 cm in length or width fixed with H or F channel complete all as specified and directed.

Supply and fixing 5.0 mm thick sheet glass, ordinary quality plain or tinted and glazing with rubber gasket in square exceeding 0.5 Sqm in each pane, complete all as specified and directed.

Supply & fixing in repairs stainless steel type curtain rod 22 to 25mm dia as per sample including SS brackets, decorative fincals and wall to wall fixed with screw and plugs as directed by Engr-in-charge.

Supply and fixing vitreous china wash basin white oval under counter type excluding taps, waste, chain & plug and porcelain stopper but including fixed to RCC/Granite stone slab complete all as specified and as directed.

Supply and fixing in repair 15mm bore wash basin mixer cast copper alloy chromium plated screwed down high pressure with or without lattered HOT or COLD with long screwed shanks and fly nuts screwed for iron pipes, att as directed Engr-in-Charge.

Supply and fixing in repair 15mm bore bib tap cast copper alloy CP with crutch or butterfly handles screwed down for iron pipes or for brass ferrule all as specified and directed by Engr-in-charge.

Supplying and laying of 16mm outer dia CPVC pipes SDR 11 & Reqd all plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down or up old GI tubing complete all as specified and directed.

Supply and fixing 20 mm bore tubes medium grade galvanized with all fittings such as Tees, elbows, unions, sockets, short, lengths, plus etc. and fixed complete to walls and ceilings or laid in floors of any length including taking down or up old GI tubing all as specified and directed by Engr-in-charge.

Supply and fixing in repair 15mm bore angle valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union all as specified and as directed.

Supply and fixing in repair 15mm bore concealed stop valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union all as specified and as directed.

Supply and fixing in repair PVC connection 15mm size with PTMT nuts of length 450mm all as specified and directed by Engr-in-charge. (Make:Parryware/Prayag/plumber)

Supply and fixing in repair brass chromium plated soap tray/dish fixed with CP screws etc complete all as specified.

Supply and fixing Rotational molded polyethylene water storage tanks white tripple layered (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position including dismantling water tanks of capacity exc 500 ltr abut n exc 1000 ltr andremoving to store all as specified and directed by Engr-in-charge.

Supply and fixing in repair PVC ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes all as specified and directed by Engr-in-charge.

Supply & Fixed in repairs 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified. (Make: Kirloskar/Zoloto

Taking down cement plaster from brick walls ,concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on brick or concrete surface of any description, complete all as specified.

Material and Labour for 15mm thick rendering on fair faces of brick work, concrete surfaces in cement mortar 1:4 mixed with WPC as per manufacturer’s instructions, finished even and fair, complete all as specified. (Note : WPC shall be measured and paid separately)

Material and labour 10 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement all as specified and directed.

Supply only integral water proofing compound, complete all as specified.

Preparing new plastered or unplastered surfaces and applying 1 mm thick Birla/JK wall care white putty in two coat including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coat of acrylic distemper over one coat of alkali resistance primer on wall complete all as specified and as directed.

Preparing new plastered or unplastered surfaces and applying 1 mm thick Birla/JK wall care white putty in two coat including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coat of acrylic distemper over one coat of alkali resistance primer on ceiling complete all as specified and as directed.

Preparing new plastered or unplastered surfaces and applying 1 mm thick Birla/JK wall care white putty in two coat including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coat of exterior emulsion paint over one coat of alkali resistance primer on wall complete all as specified and as directed.

Complete removal of existing treatment and reparing plastered or unplastered surfaces and applying 1 mm thick Birla/JK wall care white putty in two coat including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coat of acrylic distemper over one coat of alkali resistance primer on wall complete all as specified and as directed.

Complete removal of existing treatment and reparing plastered or unplastered surfaces and applying 1 mm thick Birla/JK wall care white putty in two coat including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coat of acrylic distemper over one coat of alkali resistance primer on ceiling complete all as specified and as directed.

Complete removal of existing treatment and reparing plastered or unplastered surfaces and applying 1 mm thick Birla/JK wall care white putty in two coat including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coat of exterior emulsion paint over one coat of alkali resistance primer on walls complete all as specified and as directed.

Material & Labour for two coat of synthetic enamel painting to wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer cpmplete all as specified and directed.

Material & Labour for two coat of synthetic enamel painting to steel surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of red oxide primer complete all as specified.

Material and labour Preparation of old painted wood or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint of approved shade & quality complete all as specified and directed.

Material and labour Preparation of old painted steel or iron based surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint of approved shade & quality complete all as specified and directed.

Dismantling of any dia and size cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out complete all as specified and directed.

Supply & Fixed for 100 mm bore cast iron soil waste and vent spun pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified.

Supply & Fixed for 75 mm bore cast iron soil waste and vent spun pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified.

Supply & Fixed cast iron bends 100mm bore (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified.

Supply & Fixed cast iron bends 75 mm bore (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified.

Supply & Fixed 100 mm bore cast iron branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified.

Supply & Fixed 75 mm bore cast iron branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified.

Supply & Fixed 100mm bore cast iron bends with oval access doors (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified.

Supply & Fixed 75 mm bore cast iron bends with oval access doors (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified.

Material and labour in repairs 75mm dia cast iron floor trap with with / without hole Stainless steel grating including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

Material & labour for PCC 1:2:4 type B-1 ( using 20mm graded mechanically crushed stone aggregate) as in bed blocks, copings, apex stones,side of interlocking tiles etc complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified.

Material and labour for providing reinforced cement concrete 1:2 :4 type B1 using (20mm graded stone aggregate ) as in slab supported on wall,beam, cantilevers and kitchen cooking platform complete all as specified.

Material and labour for RCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate as in chajjas beams etc complete all as specified and directed.

Material and labour mild steel TMT bars, 8 mm dia, cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Material and labour mild steel TMT bars, 10 mm dia and over, cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Material & Labour Brick work using old size bricks with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per description of Srl item No 121 above item but except bricks

Demolition of PCC as in roof padding including existing roof treatment etc over roof surfaces upto 6 mtr height from ground level complete all as specified and directed.

Material & Labour PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in roof padding & filling depressions etc & to maintain certain desired slopes.

(a) Material & Labour for 10 mm thick screeding in cemnt mortar 1:3 on Brick work or concrete surfaces on roof surface mixed with WPC, surface finished even and smooth without using extra cement. (b) Apply first coat of bitumen primer conforming to IS 3384 - 1986 @ 0.40 Kg/sqm. (c) Second coat of bonding material using hot blown type bitumen conformig to IS-702-1988 grade 85/25 @ 1.20 Kg/Sqm (d) Third layer of 3mm thick APP modified polymeric membrane with non woven polyster reinforcement shall be laid by torch appilcation method. the side overlaps of minimum 75mm and the end overlaps of minimun 100 mm. All overlaps & joints shall be sealed as per manufacturer instructions. (e) Fourth coat of bonding material using hot blown type bitumen conformig to IS-702-1988 grade 85/25 @ 1.20 Kg/Sqm. (f) Fifth and top most coat layer of surface finished 25mm thick PCC 1:2:4 type B-1 using 12.5 mm graded crused stone aggregate in roof padding over APP membrane, the surface of concrete is to be finished even and smooth with using extra cement and provided V shaped grooved 6mm wide & 10mm depth filled with using mastic bitumen of (1:1) complete all as specified and directed.

Material & labour for fabrication of pressed steel cupboard shutter using 1mm thick MS plain sheet with frame 1.25mm thick bent to shape including two coat of synthetic enamel paint on internal surfaces & two coat of hammer tone finish on external surface alongwith locking arrangement mortice lock ,handle etc complete all as specified and as directed.

Supply and fixing , vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified and as directed.

Supply and fixing Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe).(Make-Cera/Hindware/Parryware/Pryag)

Supply and fixing Plastic water closet seat, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device all as specified and directed by Engr-in-charge. (Make-Cera/Hindware/Parryware/Pryag)

Supply and fixing CP jet spray with flexible tube etc complete all as specified & directed. (Make-Cera/Essco/Coronet/Prayag)

Supply and fixing in repair 15mm bore 2 way angle valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union all as specified and directed by Engr-in-charge. (Make-Cera/Essco/Coronet/Prayag)

Supply and fixing in repair 10 Ltr capacity PVC valveless, polymer coloured, (Polypropeylene Derlin and ABS) syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle icluding bracket, flush pipe of 32 mm dia & PVC connection 15mm size, 450mm long with PTMT nuts, including taking down old u/s cistern any description, complete all as specified and as directed.

Supply & fixed in repairs stainless steel sink with drainage board , made out of 1.00mm thick sheet for kitchen oe laboratory with plug,washers, waste pipe, cast irn cantilever bracket of overall size 1040x510x203mm and bowl size 510x405x203mm complete all as specified and as directed.

Supply & fixed in repair stainless steel plate rack made out of 1.00mm thick sheet of size 750mm x 900mm x 200 mm complete all as specified and as directed.

Supply and fixing in repair 32mm bore Low density Polyethylene Pipes (LDPE) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors all as specified and as directed.

Material & Labour 18/19mm thick block board ,grade 2 quality interior grade , commercial type fixed with screw to timber frame work including taking down complete all as specified and directed.

Material & Labour Decorative laminate type 1 of 0.9 mm thick surface finish, colour and pattern as approved, fixed with approved adhesive as manufacturer's complete all as specified and directed.

Supply and fixing 75 mm long stainless steel butt hinges with galvanised MS hinge pin etc.

Supply & fixed 75mm long stainless steel handle fancy type fixed with nut and screws to cupboard shutter complete all as specified and directed.

Supply & fixed magnetic ball catches with 8mm dia steel ball brass body and striking plate including letting in and fixed, complete all as specified

Supply & fixing in repair Brass CP mixer for Bath/Sink/WHB for mixing hot & cold water screwed down for iron/CPVC pipe and fixed complete all as specified and directed.

Supply and fixing ball bearing slide length 17 " width 46mm and 12mm thick complete all as specified and directed (for measurement length shall be measured in close position) (Make: Haffle/Godrej/Hettich)

Supply and fixing beading 1st class soft wood of cross sectional area area 19mmx3mm fixed with the help of head less nails duty polished complete all as specified.

Supply and fixing coloured Vetrified Ceramic tiles 600mm x 600mm, 8-10mm thick (square/rectangular) polished, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:4), complete all as specified.

Supply and fixing coloured Vetrified Ceramic tiles 600mm x 600mm, 8-10mm thick (square/rectangular) as in skriting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM(1:4), complete all as specified.

Supply and Fixed suspended false ceiling system using Chicago metallic (E - grid) exposed suspended system, grid size 600mm x 600mm comprising of GI powder coated Main Runner of dimensions 39mm x 24mm x 0.8 mm thick (Thickness comprising of GI/0.4 mm+ PPPCGS/0.3 mm & weight of runner 1.35 kg for 3600 mm length), Cross Tee of dimensions 29mm x 24mm x 0.8mm thick (Thickness comprising of GI/0.4mm + PPPCGS/0.3mm & weight of Tee 0.195 kg for 600mm length) and Wall angle of dimensions 22.2mm x 22.2mm x 0.65mm thick (Thickness comprising of GI / 0.35mm + PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length) with and including 6mm thick HPSC (High pressure steam cured) pre primed, self embossed, textured designer board to be placed in the grid system duly suspended with 4mm dia GI wire hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt-0.007 kg/clip), hold down clips (wt-0.0035 kg/clip), with provn of light fixture complete all as per manufacturer instructions and as directed including taking down existing false ceiling of any description and size.

Material & Labour PCC type C-2 (1:3:6) using 40 mm graded stone aggregate as in sub base/mass concrete and finished the top surface even and fair without using extra cement complete all as specified.

(a) Material & Labour for 10 mm thick screeding in cemnt mortar 1:3 on Brick work or concrete surfaces on roof surface mixed with WPC, surface finished even and smooth without using extra cement. (b) Apply first coat of bitumen primer conforming to IS 3384 - 1986 @ 0.40 Kg/sqm. (c) Second coat of bonding material using hot blown type bitumen conformig to IS-702-1988 grade 85/25 @ 1.20 Kg/Sqm (d) Third layer of 3mm thick APP modified polymeric membrane with non woven polyster reinforcement shall be laid by torch appilcation method. the side overlaps of minimum 75mm and the end overlaps of minimun 100 mm. All overlaps & joints shall be sealed as per manufacturer instructions. (e) Fourth coat of bonding material using hot blown type bitumen conformig to IS-702-1988 grade 85/25 @ 1.20 Kg/Sqm. (f) Fifth and top most layer Vitrified out door tiles 40 cm x 40 cm x 10 mm thick digital design (Make-H & R Johnson, Brand-Endura digital designer series or equivalent) set, jointed and pointed in neat cement slurry as in floors with grey cement over & including over screed bed or bedding layer of mortar 20 mm thick Cement Mortar 1:4 complete all as specfied and as directed.

Material & Labour for Vitrified out door tiles 40cm x 40 cm x 10 mm thick digital design set, jointed and pointed in neat cement slurry as in floors with grey cement over & including over screed bed or bedding layer of mortar 20 mm thick Cement Mortar 1:6. (Make-H & R Johnson, Brand-Endura digital designer series or equivalent)

Complete removal of existing treatment and reparing plastered or unplastered surfaces and applying two coat of Cement base paint over one coat of alkali resistance primer on walls complete all as specified and as directed.

Dismantling of loose concrete from RCC, cleaning the reinforcement by using deruster of approved make and painting with rust preventer and then putting the weld galvanised steel mesh 75mm x 75mm of 2.80mm dia with nails and coating primer and bonding agent over RCC surface then shotcreating/guniting minimum 20mm to 40mm thick in cement mortar 1:2 and 15mm thick plastering in cement mortar 1:3, finished even and smooth including use and waste of necessary form work and scaffolding, shoring and struting the roof slab, beam, column by putting necessary support to roof and beam and column and removal after completion of work complete all as specified and directed. Note : (i) Each stage i.e. preparation of surfaces, application of derusting , wire netting, coating primer ,guniting in cement mortar 1:2, 15mm plastering in cement mortar 1:3, formwork and scaffolding will be got passed from AGE (I). (ii) The item shall be carried out upto 25.00 m height.

Material & Labour grouting in walls through GI spouts at 4Kg/Sqm pressure with non shrink free flow polymerised grout super grout NS manufactured by m/s Tufshield combine pvt ltd or equivalent to fill up all capilaries voids honey combing areas insides the entire depth of concrete substrata and applying 15mm thick plastering, finished even and fair all as specified and directed by engr-in-charge.

Grinding, cutting and polishing (Granite finish) of existing kota stone floor and making mirror polishing, complete all as specified.

Material and labour POP cornices of 75mm to 100mm wide fixed at bottom and edge of ceiling and shall be painted with oil bound distemper over a coat of primer complete all as specified and directed.

Removing building materials etc. to a distance of 1.5 KM or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination.

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. all as directed by engineer in charge.

Material & Labour for point wiring with 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated, FRLS and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continous earthing in & including PVC rigid conduit concealed with accessories having ISI mark fixed on wall surfaces / ceiling including provision of PVC box of appropriate size for fixing switches sockets etc. all as specified (Make of cable: Kalinga/Havells/ Anchor) for One light point / Fan/ bell point controlled by one switch.

(a) One light point controlled by one 5 Amps switch

(b) One Fan point controlled by one 5 Amps switch

(d) One socket 3 Pin 5A pin socket oulet 5Amps on same board with cables 1.5 Sqmm size

(e ) One socket 3 Pin 5A pin socket oulet 5Amps on indepndent board with cables 1.5 Sqmm size.

(f) One socket 3 Pin 15A pin socket oulet 15Amps on indepndent board with cables 4 Sqmm size

(g) One light point controlled by two 2-way switch

(h) All the item no 2(f) above but for One socket 3 Pin 15A pin socket oulet 15Amps on independent board with cables 4 Sqmm size for geyser point

Supply and fixing switch piano flush type single pole one way 5/6 Amps. Make : Anchor / Leader/ Kinjal.

Supply and fixing switch piano flush type single pole two way 5/6 Amps. Make : Anchor / Leader/ Kinjal.

Supply and fixing stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd

Supply and fixing lamp holder Angle / batton type insulated body with back plate and to be fixed on PVC bock. Including dismantling old one. Make : Anchor / Leader/ Kinjal

Supply and fixing socket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin/2 pin plug complete including dismantling old one. Make : Anchor / Leader/ Kinjal

Supply and fixing of switch piano15 Amp 230 Volt, flush button single pole one way complete all as specified and directed by Engr-in-Charge including dismantling old one. Make : Anchor / Leader / Kinjal

Supply and fixing socket outlet 2 in 1, 3 pin 5/6 Amps and 3 pin 15/16 Amps flush type including old one Make : Anchor / Leader /Kinjal

Supply and fixing ceiling rose surface tpe 3 terminals to be fixed on PVC block including dismantling old one. Make : Anchor / Leader / Kinjal

Supply and fixing LED integrated batten tube light fittings 22 Watt 4 Feet long complete up with twin core twisted flexible copper conductor cable of size 23/0.0076 complete all as specfied and directed.Make Havells/CG/ Phillips

Material & Labour MCB SPN DB sheet metal enclosure double door suitable for mounting MCB 240 Volts with busbar 8 way including dismantling old one. Make : Havells / Legrand / Schneider/Standard

Material & Labour MCB SPN DB sheet metal enclosure double door suitable for mounting MCB 240 Volts with busbar 4 way including dismantling old one. Make : Havells / Legrand / Schneider/Standard

Material & Labour MCB SPN DB sheet metal enclosure double door suitable for mounting MCB 240 Volts with busbar 2 way including dismantling old one. Make : Havells / Legrand / Schneider/Standard

Supply and fixing RCBo'S DP 30mA 230 Volts 32 Amps. Make : Havells/Legrand/Standard/ C&S

Supply and fixing MCB SPN 230 Volts 40 Amps. Make : Havells/Legrand/Standard/ C&S

Supply and fixing MCB SP 230 Volts 6- 32 Amps. Make : Havells/Legrand/Standard/ C&S

Supply and fixing only LED lamp 9W system lumen (NOM) 600 with all accessories all as specified and directed by Engr-in-Charge.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan including 1.5 sqmm wire if required at site

Supply and fixing exhaust fans AC single phase 230/240Volts of size 150/200 mm sweep with louver and complete accessories ,including making hole with suitable size for Exhaust Fan, after completion of work, finishing with cement and plastering and repainting with exisitng color all as specified and directed by Engr-in-charge.

Material & labour for earthing complete with galvanised steel earth plate electrode 60x60cmx6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below the ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to galvanised earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or of steel all as shown in electrical plate No 3 of SSR part-I 2009 connected to main switch board all as specified and testing on completion including. Necessary excavation, earthwork, PCC works and CI earth pit cover with watering pipe 20mm dia GI pipe medium grade, funnel with wire mesh and lugs and GI pipe 15 mm dia of light grade, for protection of earth lead complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 3.5core

Excavating in trenches n.exc 1.5 m width and n.exc 1.5m in depth for taking out cable and cable cover and getting out in any type of soil

Returning, filling in, including spreading levelling, watering and well ramming in layers n.exc 25 Cm

Removing excavated materials n.exc 50 mtr depositing where directed at a level n.exc 1.5 m above the starting point

Material & Labour for sand cushioning to PVC/ XLPE cables with tibba sand and punning to provide required cover to UG cables. Note :- For the purpose of payment only punned thickness will be measured

Material and labour for stone slab ( patti) roughly hammer dressed stone 25 to 35 mm thick 25 to 30 cm wide and not less than 60 cm long laid dry and abutting each other with gap between adjacem,ent salb not exceeding 10 mm over underground cables for protection.

Taking out old unserviceable protection Pipe and supply and fix light grade 40 mm dia GI pipe fix complete to Wall , Poles etc with suitable clamp for protection of cable complete all as directed

Supply and fixing Submain wiring alongwith earth wire with the following sizes of 2x2.5 sqmm + 1x1.5 sqmm FR PVC insulated copper conductor, single core cable in surface/recessed as required.

Supply and fixing Submain wiring alongwith earth wire with the following sizes of 2x 4.0 sqmm + 1.25 sqm FR PVC insulated copper conductor, single core cable in surface/recessed as required.

Taking down old Sheet metal enclouser and supply and fix new sheet metal enclouser cubical type factory fabricated made out of 1.6 mm thick CRCA sheet with front side openable single door system powder coated painted to shade RAL 7032, PL Gasket, hinged single door ,IP-55 mounting plate made out of 2mm thick CRCA sheet steel and earth bolts etc. of size 600x500x200mm all as speceified & directed by Engr-in- charge. Note :-- Cost of any minor modification if required in fixing of the sheet metal enclouser as per site requirement and making good the disturbed surfaces matching with existing finish, will be deemed to be included in the cost of this item.

Supply and fixing LED security light luminaries of 25 watt for energy saving having IP-65 degree of protection made of pressure die cast aluminum housing and heat resistant thoughned glass with excellent thermal management, LED's should have better optics and uniform distribution of light including GI tubing 40mm dia light grade 1.2 mtr long pipe bent to shape 120 degree for mounting of security light and fixed to wall/pole, with suitable MS clamps 2 Nos with nut and bolt and washers including connecting complete including 1.5 sqmm stranded copper conductor of suitable length as per direction and approved by Engr-in-charge.

m/s sharma constructions

M/s Ajay kumar Garge

M/s SUNIL ENTERPRISES