SPECIAL REPAIR OF JCO SINGLE LIVING BLDG NO E 11 12 AT 115 ENGR REGT ANF PROVN OF CATTLE TRAP NEAR GE ( SOUTH) AND AT GOLDEN FISH PHYSICAL TRG AREA AND SPORTS COMPLEX UNDER AGE B/R-II AND AGE E/M-I OF GE ( NORTH) MEERUT CANTT

Amount

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Removng excavated soils n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed

Taking down chowkhat with shutters without taking of shutter from the frames not exc 1.5sqm each complete all as specified and directed . Note- Disturbed suface of wall shall be made good to true suface

Taking down chowkhat with shutters without taking off shutters from the frame exc 1.5sqm but n.exc 4 sqm each complete all as specified and directed Note- Disturbed suface of wall shall be made good to true suface

Demolition of brick work or stone boulders masonry built in cement mortar including all quoins arches pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc complete all as specified and directed complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving n.exc 15cm thickness below or above grond level complete all as specified and directed

Demolition of wall and ceiling boards fibre,pulp insulation etc or insulation boards /slabs/blankets any thickness including cover fillets complete all as specified and directed

Taking down of cement or cement lime plaster/skirting/ dado of any description from brick or stone wall etc. including raking out of joints, hacking for key, scrubbing down with water etc complete all as specified and directed

Dismanting AC sheet corrugated or semi corrugated sheet including ridge of any description as in roof and including removal from the site complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering ,cladding to wall fixed with self tapping screws complete all as specified and directed

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering , cladding to wall fixed with self tapping screws complete all as specified and directed

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty or fixed with wooden beads in square n exc 0.50 sqm each pane complete all as specified and directed

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed

M&L for applying 10 mm thick rendering on ceiling in cement mortar 1:3 finished even and smooth with out using extra cement complete all as specified and directed

M&L for applying 15mm thick rendering in CM 1:4 using ready mix plaster bags on brick/concrete surface of extenal wall finished even and fair complete all as specified and directed Make : Ultratech, rediplast, Birla Acrocem. Note Contractor is required to deposit ready mix bags for 100% CA quanitity to Engr-in-charge with in 15 days of acceptance of contract.

M&L for preparation of old/new plastered suface of wall and applying two coats of Acrylic exterior Emulsion paint using roller for painting complete all as specified and directed

M&L for preparation of old/new plastered suface of wall and applying two coats of oil bound distemper using roller for painting complete all as specified and directed

S&F 2nd class hard wood 35mm thick plain framed , panelled shutters(any number of panels) with panels of timber flat on both sides( feather edged) or of veneered particle board medium density ,wood particle board with panel shutter shall be two leaf in one opening complete all as specified and directed

S&F 2nd class hard wood 35m thick glazed and skeleton shutter open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/gauze etc, glazed and skeleten shutter shall be two leaf in one opening sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed

S&F steel windows with pressed steel frame made out from 1.25mm thick steel with one or more rebate with glazed shutters and fly proofing shutters including guard bars, hinges ,peg stay, handles, tower bolts, lugs including treated with for or coal tar black paint on steel surface in contact/embedded in concrete/masonry work complete all as specified and directed Note- Disturbed suface of wall shall be made good to true suface

S&F floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor over all length of cover plate 140 mm complete all as specified and directed

S&F 100mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed

S&F 250mm length of bolt aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed

S&F galvanised mild steel wire cloth, 0.63 mm nominal dia. of wire and avg width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire stapples complete all as specified and directed

S&F aluminium anodised 150mm length of bolt barrel tower bolt of extruded section complete all as specified and directed

S&F 125mm size of aluminium handles cast type anodised complete all as specified and directed

M&L for preparation of newly wooden surfaces and applying two coats of synthetic enamal paint over a coat of pink primer over 10CM width or girth complete all as specified and directed

S&F mild steel 30mm ordinary rat tail rod pattern springs including roller complete complete all as specified and directed

M&L for preparation of new steel suface and applying two coat of synthetic enamal paint over a coat of red oxide over 10CM width and girth complete all as specified and directed

S&F anodised aluminium snap grid size of grid 605X605mm for false ceiling complete all as specified and directed

S&F 4mm thick non asbestos fibre cement building boards fixed or laid /inserted to timber /GI/aluminium frame work with screws complete all as specified and directed

S&F mild steel Fe - 290 (Gde E- 165) for Framed work as in doors , chowkhats or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, support to sign board & fencing post, etc. as specified to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed

S&F mild steel rolled sections FE 410-W (grade E-250) quality a as in main and cross beams base plates, side supports, hip and jack rafters, purlins, winties where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting member as directed and specified and directed by Engg-in-Charge

M&L for providing 75mm thick cement concrete type C-2 1:3:6(40mm graded stone aggregate) for plinth protection finished even and fair complete and providing joints complete all as specified and directed

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS : 15658-2006 of 60mm thickness M-35 grade grey cement and no pigments laid over and including 50mm thick compected sand cushion complete all as specified and directed

M&L for providing 75mm thick cement concrete type B-2 1:2:4(40mm graded stone aggregate) as in sub base complete all as specified and directed

M&L for vetrified ceramic tiles dark shade/double charge 7 to 8mm thick/altra charged (square/rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm in floor etc set and jointed in neat cement slurry and pointed in choice or coloured cement to match the coloured tiles over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed

Ditto as above item No 38 but on verical surface over and including 10mm thick cement mortar 1:4 complete all as specified and directed

M&L for brick work with fly ash bricks straight or curved on plan exc 6M mean radious build in cement mortar 1:6 complete all as specified and directed

Dismantiling timber scantlings 40 and over in section in any position unframed work complete all as specified and directed

S&F stainless steel peg set 8 nos in 45cm length and dia of hooks 6mm complete all as specified and directed

S & F 80mm GI Tubes, 'heavy grade', galvanised,with all fitting; laid in trenches complete all as specified and directed.

S & F for Compound girders( beam of I section ) and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc Fe-410-W(Gde?E-250) Quality B complete all as specified and directed

M & L for Cement Concrete M-25 design mix as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement, slabs, under-reamed piles and mass concrete all as specified and directed

S&F mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing clips complete all as specified and directed.

Ditto all as per item No 46.00 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished concrete surfaces complete all as specified and directed.

Rough excavation not exceeding 1.5 m deep and getting out soft /loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.complete all as specified and directed.

M&L for broken stone/ boulders hard core, of gauge n exc 63 mm deposited spread and levelled in layers not exc 15 cm thick watered and rammed to true surfaces complete all as specified and directed.

M &L for Cement concrete in foundations, filling and mass concreteType C2 1:3:6 (40 mm graded stone aggregate)complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft/loose soil etc. including trimming bottom and sides of trenches, leveling/ grading and ramming bottom of excavation complete all as specified and directed.

M&L cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in coping and similar work complete as specified.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in precast manhole / septic tanks covers including necessary form work and setting in CM 1:4 complete all as specified and directed.

M&L Ultra P E,DWC (Double wall corrugated) pipe confirming IS-16098 Part-2 2013 pertaining structure wall plastics pinning system for sewage 150 mm bore and above bore pipe SN-8 and all necessary fittings and fixtures complete all as specified and as directed.

M&L for 15-18mm thick (ruby red/ colour) granite fixing on vertical face of curved wall vertical surface and Including rounding of edges, rubbing, matching the colour of joints, making good and backing coat of mortar 15mm thick in CM 1:4 complete all as specified and directed.

M&L for preparation of old/new plastered suface of wall and applying two coats of Acrylic exterier Emulsion paint over 3mm thick exterior grade wall care putty making smooth surface with using roller for painting complete all as specified and directed .

Taking down copper/aluminium point wiring with conduit (ligh, fan, bell, socket or power etc.) complete with all accessories for taking credit and making good disturbed surfaces, applying distemper / Emulsions matching to the existing colour / quality of walls / floors / ceiling etc all as specified.

M&L for concealed point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi stranded, Fire Retardant, conforming to IS: 694-1990 PVC insulated, sheathed copper conductor cable in and including PVC concealed conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories / fittings, brass screws, washers etc, sunken zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated copper conductor cable, sheathed and connected to common earth and earth dolly including cutting holes in or through the walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as directed for One light/fan/bell point wiring controlled by one, one way switch/bell push button.

All as per Srl item No 60.00 above but one out let socket point 3pin 5 amps on independent board complete all as specified and directed.

All as per Srl No 60.00 above but on the same board with other switches complete all as specified and directed.

All as per Srl No 60.00 above but one bell point controlled by one , one way switch 05/6 Amp complete all as specified and directed.

All as per Srl No 60.00 above but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one ,15/16 Amp socket outlet point on independent board complete all as specified and directed.

S&F switch piano flush type, 5/6A, AC, 240V, one way ISI marked complete all as specified and directed.

S&F switch piano flush type,15/16A, AC, 240V, one way ISI Marked complete all as specified and directed.

S&F Bell Push, Flush type, 5/6A, AC, 240V, ISI Marked complete all as specified and directed.

S&F socket piano flush type, 5/6A, 5pin, AC, 240V ISI Marked complete all as specified and directed.

S&F socket piano flush type 3 pin 5/6 Amp,3 pin , 15/16A,( two in one multipurpose ), AC, 240V ISI Marked complete all as specified and directed.

S&F lamp holder, PVC / Polycarbonate type with batten back plate, AC, 240V, Pin type, ISI marked complete all as specified and directed.

S&F Ceiling rose surface Bakelite 65x50mm, 3 terminals, AC, 240V, ISI Marked complete all as specified and directed.

S&F Call Bell, AC, 240V, SP, ISI Marked complete all as specified and directed.

S&F LED lamp 9/10 watts complete all as specified and directed.

S&F LED tube light fitting surface mounting, CRCA batten decorative box type , 4 feet, 240V, 20 Watt, including T-8 poly carbonate diffuser type 20 watt rectrofit tube rod complete all as specified and directed.

S&L XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volt grade cross sectional area of 16 sqmm 2 core complete all as specified and directed.

M&L for clean fine dry river sand in trenches for cushioning of under ground cable/ cable duct complete all as specified and as directed. Note: Only punned thickness shall be measured for payment purpose.

M & L for fly ash brick protection length of brick shall be laid across the length of cable complete all as specified and directed.

S&F GI light grade tubing 40mm dia laid in trenches, road crossing , pasing through pipe or laid in wall/pole complete all as specified and directed.

M&L for sub main wiring with 06 Sqmm nominal cross sectional area, two run of single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor FR- FLEXIBLE WIRING CABLE. CONFORMING TO IS: 694-1990 with and including one run of continuous earth wire of size 6 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 32 mm dia, medium grade with all PVC conduit accessories / fittings, brass screws, washers etc and connected to common earth dolly including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing taking down old unserviceable sub main wiring complete all as specified & directed. Note:-One meter of conduit along with 3x6 sq mm wire shall be measured as one unit length.

S&F sheet metal enclosures double door for DB's with 200 Amps rated busbar and IP-43 protection with metal double door 8 way, SPN and flush to wall including all cutting on wall and making good to match the existing surfaces complete all as specified and directed.

S&F MCB single pole 240 volt , B series capacity 6 to 40 amps 10 KA and making connection complete all as specified and directed.

S&F MCBdouble pole 240 volt , B series capacity 32 to 40 amps 10 KA and making connection complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to centre both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1, for pit cover including testing on completion complete all as specified and directed.

M/S Keshav Brothers

AMBEY CONSTRUCTION

M/S AMAR ELEKTRO CENTRE

A.V. ASSOCIATES

S K CONSTRUCTION CO

High Tech Metal India