CONSTRUCTION OF 2 NOS TOWER TRANSIT HOSTEL G12 AT POLICE LINE IN DISTRICT HARDOI

CIVIL WORK Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete as per directed by Engineer-in-Charge. (Including Labour cess but Excluding GST)

Cast cement concrete as in door sills, chaukhat as similar precast unit with cement, approved coarse sand and 20 gauge approved stone ballast in the proportion of 1:2:4 excluding supply of reinforcement and its bending with 24 B.W.G.G.I. binding wire and including necessary scentring and shuttering etc. and also including supply of all materials labour T&P etc required for proper completion of work as per directed by Engineer-in-Charge. (Including Labour cess but Excluding GST)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but including the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.(Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). (Including Labour cess but Excluding GST)

Brick work with approved factory made non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in foundation/ super structure above plinth level up to floor V level in Cement mortar 1:6 (1 cement : 6 Coarse sand) as per directed by Engineer-in-Charge. (Including Labour cess but Excluding GST)

Providing and laying approved factory made autoclaved aerated cement blocks masonry with half thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work all as per directed by Engineer-in-Charge. (Including Labour cess but Excluding GST)

Providing and laying approved factory made autoclaved aerated cement blocks masonry with 150mm/ 230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). (Including Labour cess but Excluding GST)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto & above plinth level by using Thermo-Mechanically Treated bars of grade Fe-500D or more all as per directed by Engineer-in-Charge. (Including Labour cess but Excluding GST)

Providing and fixing factory made PROFILE-B, pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge. Fixing with adjustable lugs with split end tail to each jamb. (Including Labour cess but Excluding GST)

Providing and fixing factory made PROFILE-C, pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge. Fixing with adjustable lugs with split end tail to each jamb as directed by Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel as directed by Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing and fixing factory made PVC door frame of size 50x47 mm with a wall thickness of 5 mm made out of extruded 5 mm rigid PVC foam sheet mitred at corners and joined with 2 no of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door profiles to be reinforced with 19x19 mm MS square tube of 19 gauge EPDM rubber gasket weather seal to be provided through out of frame the door frame to be fixed to the wall using MS screws of 65/100 mm size complete as per manufactures specification and direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing and fixing factory made Kiln seasoned and chemically treated hollock wood ,35 mm thick panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, including panelling etc. all complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing and fixing factory made panel PVC door shutter consisting of frame maid out of MS Tubes 19 gauge thickness and size of 19 mm, 19 mm for styles and 15x15 mm for top and bottom rails MS frame shall have a coat of steel primers of approved make and manufacture MS frame covered with 5 mm thick heat moulded PVC channel of size 30 mm thickness 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tappered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapperd on both sides to form lock rail top bottom and lock rails shall be provided either side of the panel 100 mm thick 20 mm wide cross PVC sheet be providedas gap insert for top rail and bottom rail paneling of 5 mm thick both side PVC sheet to be fitted in MS frame welded/ sealed to the styles and rails with 7 mm thick x 15 mm widePVC sheet beading on inner side and joined together with solvent cement adhesive an additional 5 mm thick PVC strip of 20 mmm width is to be stuck on the interior side of C channel using PVC solvent adhesive etc complete as per direction of Engineer-in-Charge and manufactures specification and drawing. (Including Labour cess but Excluding GST)

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) all as per directed by Engineer-in-Charge. (Including Labour cess but Excluding GST)

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer using M.S. angels 40x40x6 mm for diagonal braces all as per directed by Engineer-in-Charge. (Including Labour cess but Excluding GST)

Providing and fixing ISI marked, 250x16 mm size, anodised aluminium sliding door bolts with nuts and screws etc. complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing ISI marked, 300x10 mm size, anodised aluminium tower bolt black finish, (Barrel type) with necessary screws etc. complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing, 150 mm size bright /matt finished Aluminium handles of approved quality & make with necessary screws etc all complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing & fixing, 4 mm thick plain glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing ISI marked factory made 35 mm thick, flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters all complete as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing, M.S. tube hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer all complete as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides all complete as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of 20mm thick plaster with 1:4 cement and coarse sand mixed with water proofing compound finished with neat cement For the purpose of measurement the entire treated surface will be measured all complete as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

6 mm thick plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of Engineer-In-Charge. (Including Labour cess but Excluding GST)

Providing and laying water proofing treatment in sunken portion of WC. BATH & WHB etc. by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. this layer will be allowed to air cure for 4 hours. (b) second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. this layer will be allowed to air cure for 4 hours followed with water curing 48 houres The rates includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and laying Ceramic Anti Skid glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

4 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand and 2cm. (3/4") graded approved stone laid in panels finished with 3 mm. (1/8") floating coat of neat cement or cement and marble dust in 5:1 as specified over base concrete/ slab and giving them a uniform finish including supply of all materials, labour and T & P etc. required for proper completion of the work all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing, 25 mm wide and 4 mm thick, glass dividing strips in joints of terrazo/ cement concrete floors complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

2 cm. (3/4") thick cement plaster in dado or skirting in 1:2 consisting of one part of cement and 2 parts of approved coarse sand laid in panels, finished with 3 mm.(1/8") floating coat of neat cement or cement and marble dust in ratio of 5:1 including supply of all materials, labour and T & P etc., required for proper completion of the work all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing 18 mm thick, Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and laying of 80 mm thick pre moulded inter locking paver tiles over 10 cm compected GSB & 7.5 Cm G-3 including 3 cm thick coarse sand bed over prepared surface including all material, labour T&P etc. required for proper completion of work as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Applying one priming coat & two or more coat oil distemper on new work including supply of all materials, labour and T& P etc. required for proper completion of the work as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Finishing walls with water proof cement paint of approved make and quality on new work with two coats over one coat of primer to give an even shade. Including supply of all material labour and T & P etc required for proper completion of the work as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Painting two coats over a priming coat on new iron or steel surfaces up to 10 cm width or sq,mt in areas with superior synthetic enamel such as Luxol-3 Hi-gloss apcolite superlac, Dulux specified finishing to give an even shade & incl. cleaning the surface of all dirt, dust & other foreighn matter sand preparing and knotting incl. cost of all etc. required for proper completion of work as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Painting two coats over a priming coat on new wood surfaces up to 10 cm width or sq,mt in areas with superior synthetic enamel such as Luxol-3 Hi-gloss apcolite superlac, Dulux specified finishing to give an even shade & incl. cleaning the surface of all dirt, dust & other foreighn matter sand preparing and knotting incl. cost of all etc. required for proper completion of work as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 coars sand) as per standard design in 75x75 mm deep chase complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Extra for RCC/BMC/RMC work above floor V level for each four floors or part thereof.Above fifth to eight floor complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Same as above in item no. 41 but 9 th to 13th floor (Including Labour cess but Excluding GST)

Same as above in item no.41 but 13th to above floor (Including Labour cess but Excluding GST)

Extra for fly ash brick/ AAC masonary work above floor V level for each four floors or part thereof, Six to Nine floor complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Same as above in item no. 44 but 10 th to 12th floor (Including Labour cess but Excluding GST)

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m part thereof.Above 10th to 13th mt complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Same as above in item no. 46 but 13th to 16th mt (Including Labour cess but Excluding GST)

Same as above in item no. 46 but 16th to 19th mt (Including Labour cess but Excluding GST)

Same as above in item no. 46 but 19th to 22th mt (Including Labour cess but Excluding GST)

Same as above in item no. 46 but 22th to 25th mt (Including Labour cess but Excluding GST)

Same as above in item no. 46 but 25th to 28th mt (Including Labour cess but Excluding GST)

Same as above in item no. 46 but 28th to 31th mt (Including Labour cess but Excluding GST)

Same as above in item no. 46 but 31th to 34th mt (Including Labour cess but Excluding GST)

Same as above in item no. 46 but 34th to 37th mt (Including Labour cess but Excluding GST)

Same as above in item no. 46 but 37th to 40th mt (Including Labour cess but Excluding GST)

Providing & laying the VDF concrete flooring (Trimix flooring) 62mm thick with concrete hardener topping under layer 50 mm thick cement concrete 1:2:4 and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume. Hardening compound is mixed @ 2 liter per 50 kg of cement or as per manufucturer's specifications complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Supply and fixing steel murga jali on the junction of RCC and brick work before wall plaster to improve the stability of plaster complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Earthwork in excavation for structures as per drawing and technical specification clause 305.1 including setting out. Construction of shoring and bracing, removal of stumps and other deletenous materials and disposal upto a lead of 50m. Dressing of sides and bottom and backfilling in trenches with excavated suitable material complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Providing and laying Cement concrete 1:4:8 (1cement :4 coarse sand :8 graded stone ballast 40 mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete as per directed by Engineer-in-Charge also including cost of formwork in foundation. (Including Labour cess but Excluding GST)

First class bricks work in 1:4 in cement and coarse sand in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work. (Including Labour cess but Excluding GST)

Providing and laying Cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone ballast 20 mm. nominal size) including supply of all materials. Labour and T&P etc. required for proper completion of the work and curing complete also including cost of formwork in foundation and floors. (Including Labour cess but Excluding GST)

P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. (Including Labour cess but Excluding GST)

12 mm thick plaster with cement mortar in proportion of 1:2 cement and fine sand of 1.25 F.M. (Including Labour cess but Excluding GST)

SANITARY & WATER SUPPLY Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS:7231, Parryware/Hindware/Seabird or equivalent White Vitreous China Orissa pattern W.C. pan of size 580x440mm with integral type foot rests complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing P.V.C. waste pipe of approved make for sink or wash basin including P.V.C. waste fittings complete.PVC Flexible pipe 32mm dia for wash basin complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing P.V.C. waste pipe of approved make for sink or wash basin including P.V.C. waste fittings complete.PVC Flexible pipe 40 mm dia for Sink & Urinals complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink of approved make as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 250 mm complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing & fixing white vitreous china wash basin with C.I. brackets painted white, 15 mm C.P. brass pillar taps, C.P. brass chain with rubber plug, 32mm C.P. brass waste of standerd pattern including cutting & making good the walls wherever required. White Vitreous China Wash basin Parryware/ Hindware/ Seabird or equivalent and size 630x450 mm with a pair of 15 mm C.P. brass pillar taps complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Bottle trap PTMT 38 mm single piece moulded with height of 270 mm, of approved make effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing C.P. brass Double coat Hooks of approved design and make with CP screws complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing of the Single lever sink mixer with Swinging Spout on upper Side ( wall mounted model ) with connecting legs & wall flangese (make jaquar ARI-391165 or equivalent) complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality and make) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing CP Brass Single lever telephonic wall mixer 15 mm nominal dia of quality & make jaguar or equivalent as approved by Engineer in charge. (Including Labour cess but Excluding GST)

Providing and fixing C.P. brass shower rose 150 mm diameter with 15 or 20mm inlet quality & make jaguar or equivalent as approved by Engineer in charge. (Including Labour cess but Excluding GST)

Providing and fixing CP Brass towel rail of approved pattern and make and size 750x20mm together with pair of CP brass brackets to fit the towel rail complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing C.P. Soap dish, Jaquar ESSCO, cera,hindware or equivalent with concealed fitting including supply of all material , labour T&P etc. complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing of approved coloured vertical type hot water geyser, the inner container shall be made of copper sleeve with PUF insulation between inner and Outer container, element Pipe and heating element, pressure cum vacuum release thermostate and thermal cutout arrangements and fusible plug. The outer container Shall be powder coated finish with all other accessories including fixing brackets complete all required capacity 25 Litre Made by Approved Brand and quality complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Wall mountable water purifier with transparent cover mineral ROTM Technology double purification by RO + UF with TDS controller- Kent Pride or equivalent complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes 110 mm bore of approved make conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing unplasticised -PVC pipe 110 mm bore clips of approved design and make to unplasticised- PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc.directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and laying cement concrete 1:5:10(1 cement : 5 coarse sand : 10 graded stone aggregate 20mm nominal size) around P.V.C Soil and waste pipe 100/90 mm dia including bed concrete as per standard design(embedded in the flooring / ground) complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

HEP Nahani Trap of Indian make HCI 100X75 mm complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

C.I. man hole cover with frame weight not less than 11 kg complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing & fixing 15 mm nominal bore 45 cm long of approved make unplasticised PVC connection pipe with brass unions complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing C.P. brass long nose bib cock 15 mm nominal bore of approved quality and make jaguar or equivalent conforming to IS standards and weighing not less than 810 gms complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing C.P. brass angle valve15 mm nominal bore for basin mixer and geyser points of approved quality and make jaguar or equivalent conforming to IS:8931 complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cementmortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominalsize), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size ) and inside plasteringwith cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with afloating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing G.I. Union ISI marked suitable for G.I. pipe 25mm nominal bore including cutting and threading the pipe and making long screws etc. complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Same as above in item no. 89 but 32 mm nominal bore (Including Labour cess but Excluding GST)

Same as above in item no. 89 but 40 mm nominal bore (Including Labour cess but Excluding GST)

Same as above in item no. 89 but 50 mm nominal bore (Including Labour cess but Excluding GST)

Same as above in item no. 89 but 65 mm nominal bore (Including Labour cess but Excluding GST)

Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of approved quality and make ,25 mm dia nominal outer dia pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & Concealed work including cutting chases and making good the walls etc. complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes approved quality and make,32 mm dia nominal outer dia pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & Concealed work including cutting chases and making good the walls etc. complete all as per directed by Engineer-in- Charge. (Including Labour cess but Excluding GST)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes approved quality and make, 40 mm dia nominal outer dia pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work (Including Labour cess but Excluding GST)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes approved quality and make, 50 mm dia nominal outer dia pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work (Including Labour cess but Excluding GST)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes approved quality and make, 62.5 mm dia nominal outer dia pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work (Including Labour cess but Excluding GST)

Painting G.I. pipes 25 mm dia nominal outer dia pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Painting G.I. pipes 32 mm dia nominal outer dia pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Painting G.I. pipes 40 mm dia nominal outer dia pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Painting G.I. pipes 50 mm dia nominal outer dia pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work : (Including Labour cess but Excluding GST)

Painting G.I. pipes 62.5 mm dia nominal outer dia pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Providing and fixing 30 mm dia ball valve (brass) of approved quality and make, High or low pressure, with plastic floats complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Excavating trenches of required width for pipes, cables etc. exceeding 80mm dia but not exceeding 300mm. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Providing, laying and jointing glazed stoneware pipes 200 mm diameter class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 coase sand) including testing of joints etc. complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 gradded stone aggregate 40 mm nominal size) alround S.W. Pipes including bed concrete as per standard design. 200 mm. dia. RCC Pipes /P.V.C PIPE. complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarsesand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :Constructing brick masonry manhole with F.P.S. complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Same as above in item no. 112 but Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Same as above in item no. 112 but Inside size 90 X 80 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Same as above in item no. 112 but Inside size 120 X 90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Providing and fixing square-mouth S.W. gully trap grade ‘A” complete with C.I.grating brick masonry chamber with water tight C.I. cover with frame of 300 x300mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be notless than 2.70 kg as per standard design : 150 x 100 mm size P type.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5. (Including Labour cess but Excluding GST)

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3 coarse sand :6graded stone aggregate 20 mm nominal size) as per standard design,With 20x20 mm square bar complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers , Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm. complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Providing and laying non-pressure NP3 class (light duty) R.C.C. pipes 300 mm dia.with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 coarse sand) including testing of joints etc. complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Providing and laying Cement concrete 1:4:8 (1cement :4 coarse sand :8 graded stone ballast 40 mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete as per directed by Engineer-in-Charge also including cost of formwork in foundation. (Including Labour cess but Excluding GST)

Providing and laying Cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone ballast 20 mm. nominal size) including supply of all materials. Labour and T&P etc. required for proper completion of the work and curing complete also including cost of formwork in foundation and floors complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast,R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

RAIN WATER HARVESTING Earthwork in excavation for structures as per drawing and technical specification clause 305.1 including setting out. Construction of shoring and bracing, removal of stumps and other deletenous materials and disposal upto a lead of 50m. Dressing of sides and bottom and backfilling in trenches with excavated suitable material complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-all work upto plinth level 1:4:8 (1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size) complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

First class brick work in 1 : 4 cement and coarse- sand mortar in foundation and plinth and including supply of all materials, labour and T & P etc. required for proper completion of work as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

12 mm Cement plaster in single coat on rough side of single or half brick wall for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80 mm. in girth and finished even and smooth. (1 Cement :4 coarse sand ) complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

R.C.C. works with cement approved coarse sand 2cm (3/4") gauge approved stone ballast in the proporation 1:1.5:3 ( 1 cement :4.5 aggregate) in R.C.C. T-beams and slab roofs and R.C.C. columns excluding supply of reinforcement and its bending but including its fixing and bending the same with 24 B.W. G.G.I. binding wire and includuing necessary centering and shuttering etc. and also including supply of all materials, labour, T&P etc. required for proper completion of works. Binding wire cost being included in the Item complete as per direction of Engineer in Charge. (Including Labour cess but Excluding GST)

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. (Including Labour cess but Excluding GST)

Supply and fixing of approved quality Nylon mesh suitable for 110 mm dia pipe complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Boringof 150mm dia by palm &pressure mrthod in ordinary soil including arrangment of water of boring (Including Labour cess but Excluding GST)

lowering of 110 mm nominal size dia. Pvc pipe (Including Labour cess but Excluding GST)

Development of tube well (Including Labour cess but Excluding GST)

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 110 mm clamp all as per requirement and direction of Engineer-in-charge (Including Labour cess but Excluding GST)

. Suplaying of 110 mm diameter PVC PIPE 6 Kg /sqm (Including Labour cess but Excluding GST)

Making Jali in 110 mm dia PVC Pipe complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing and fixing Bail plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 110 mm dia complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing and fixing Well cap of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 110 mm dia complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

SEPTIC TANK & SOAKWELL Earth work in excavation over areas including disposal of excavated earth, lead upto 50m, disposed earth to be levelled and neatly dressed.In all kind of soil upto 1.5m depth complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Earth work in excavation over areas including disposal of excavated earth, lead upto 50m, disposed earth to be levelled and neatly dressed.In all kind of soil exc 1.5m depth & not exc 3.0 m depth complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing and laying Cement concrete 1:4:8 (1cement :4 coarse sand :8 graded stone ballast 40 mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete as per directed by Engineer-in-Charge also including cost of formwork in foundation. (Including Labour cess but Excluding GST)

4 cm thick 1:2:4 plane cement concrete floor with cement approved coarse sand and 2 cm (3/4") grading approved stone land in panels finished with 3 mm (1/8") flooring cost of neat cement or cement and mrble dust in 5:1 as specified over removing any over lappiing mortar at eh joints of panels in any and givind them a uniform finish including supply of all materials labour and T&P etc required for proper completion of the work complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Bricks work witth brick of class designtion 150 in foundation and plinth in cement mortar (1 cement : 4 coarse sand) ………… materials, labour and T&P etc. required for proper completion of the work. (Including Labour cess but Excluding GST)

Reinforcement cement concrete work in RCC culvert slab with 1:2:4 (1 cement : 2 coarse sand and 4 gradded stone aggregate of 20 mm nominal size) including centering and shuttering and reinforcement complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel etc complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

12mm cement plaster on rough side of mix 1:4 (1 cement : 4 coarse sand) complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing M.S. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing and fixing C.I. tee approved quality and make 150mm dia at the inlet and outlet of septic tank complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing & fixing C.I. 75mm dia vent pipes approved quality and make complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing & fixing of 75mm dia cast iron terminal guard approved quality and make complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -10- Circular shape 500mm internal diameter complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -2.5- Circular shape 450mm internal diameter complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standard design. With F.P.S. bricks complete as per direction of Engineer-in-charge. (Including Labour cess but Excluding GST)

Drilling of 250 mm dia bore hole by machine. (Including Labour cess but Excluding GST)

Supply of 100 mm dia MS casing pipe (class B) with accessories. (Including Labour cess but Excluding GST)

Supply of 100 mm dia Johnson screen (Including Labour cess but Excluding GST)

Providing and packing of coarse sand / pea gravel around the slotted pipe as required. (Including Labour cess but Excluding GST)

Transport of boring machine and tools and other required equipments and installation at site (Including Labour cess but Excluding GST)

Supply of submersible pump with control panel, support wire etc complete. Having discharge of 100 lit/min at required head. (Make : KSB CORA or Grundfos) (Including Labour cess but Excluding GST)

Providing 3 core PVC insulated copper conductor submersible cable. (Including Labour cess but Excluding GST)

Providing and fixing 40 mm dia. GI pipe complete with fittings and clamps. (Including Labour cess but Excluding GST)

Providing and fixing of 40 mm dia. brass Gate valve with CI wheel of approved quality. (Including Labour cess but Excluding GST)

Lowering of 100 mm dia MS pipe in bore hole including cutting, jointing etc complete. (Including Labour cess but Excluding GST)

Fixing, testing and commissioning for erection and lowering of submersible pump, GI column pipe, submersible cable up to the control panel, support wire, supporting clamps, cable clips, pressure gauge, connection line and all other other accessories required for the proper completion of the work. (Including Labour cess but Excluding GST)

Testing and development of Tubewell. (Including Labour cess but Excluding GST)

Please Enable Macros to View BoQ information