Tender for Design, manufacturing, supply and erection including interior and exterior finishes with LGSF,Pre-fab structure technology at the first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

DSR NSR

a) 5.9.1 Foundations, footings, bases of columns etc. for mass concrete.

b) 5.9.5 Lintels, beams, plinth bams, griders, bressumers and contilevers.

c) 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts

STEEL REINFORCEMENT -

3.2 5.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending,placing

in position and binding all complete above plinth level. -

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kilogram 3645 107.85 3,93,113

3.3 5.33 Providing and laying in position ready mixed or site batched design mix cement

concrete for reinforced cement concrete work; using coarse aggregate and fine

aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to

accelerate / retard setting of concrete, to improve durability and workability without

impairing strength; including pumping of concrete to site of laying, curing, carriage

for all leads; but excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge; for the following grades of

concrete. Note: Extra cement up to 10% of the minimum specified cement content

in design mix shall be payable separately. In case the cement content in design mix

is more than 110% of the specified minimum cement content, the contractor shall

have discretion to either re-design the mix or bear the cost of extra cement.

5.33.2 All works above plinth level upto floor V level

5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 27.00 9860.40 2,66,231

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

R.C.C. WORK SUB HEAD TOTAL 10,85,015

4.0 SUB HEAD-IV :- MASONRY WORK

4.1 6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation

7.5 in superstructure bove plinth level up to floor V level in all shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 47.67 9105.95 4,34,081

4.2 6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level. -

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) sqm #### 1123.80 2,00,036

4.3 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third

course of half brick masonry. sqm #### 104.80 18,654

MASONRY WORK SUB HEAD TOTAL 6,52,771

5.0 SUB HEAD-V :- STEEL WORK

5.1 10.16 Steel work in built up tubular (round, square or rectangular hollow tubes etc.)

trusses etc., including cutting, hoisting, fixing in position and applying a priming

coat of approved steel primer, including welding and bolted with special shaped

washers etc. complete.

10.16.1 Hot finished welded type tubes MS Frame kg #### 194.40 19,440

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

5.2 10.28 Providing and fixing stainless steel (Grade 316) railing made of Hollow tubes,

channels, plates etc., including welding, grinding, buffing, polishing and making

curvature (wherever required) and fitting the same with necessary stainless steel

nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless

steel dash fasteners , stainless steel bolts etc., of required size, on the top of the

floor or the side of waist slab with suitable arrangement as per approval of Engineer-

incharge, (for payment purpose only weight of stainless steel members shall be

considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

STEEL WORK TOTAL 96,680

6.0 SUB HEAD- VI :- FLOORING

6.1 11.41.4 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by

the manufacturer) with water absorption less than 0.08% and conforming to IS:

15622, of approved make, in all colours and shades, laid on 20 mm thick cement

mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3

kg/sqm grouting the joints with white cement and matching pigments etc.,

complete.-Size of Tile 1000x1000 mm sqm 725 2 090 15,14,996

6.2 11.46 Providing and laying Vitrified tiles in different sizes (thickness to be specified by

manufacturer), with water absorption less than 0.08 % and conforming to I.S.

15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12

mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey

cement slurry @ 3.3kg/sqm including grouting the joint with white cement &

matching pigments etc. complete.

11.46.4 Size of Tile 1000x1000 mm sqm 108.8 2 163 2,35,183

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

6.3 11.55 Providing and laying flamed finish Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick

base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement

slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge :

11.55.1 Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or

equivalent. sqm 40.00 3186.70 1,27,468

6.4 NSR Extra for pre finished nosing to treads of steps of Granite stone. sqm 40.00 726.00 29,040

6.5 11.56 Providing and laying Polished Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick

base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement

slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

11.56.1 Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent sqm 20.00 4481.30 89,626

6.6 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622

(thickness to be specified by the manufacturer), of approved make, in all colours,

shades except burgundy, bottle green, black of any size as approved by Engineer-in-

Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @

3.3kg per sqm, including pointing in white cement mixed with pigment of matching

shade complete sqm 10.00 1267.95 12,680

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

6.7 11.37A Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622

(thickness to be specified by the manufacturer ) of approved make in all colours,

shades except burgundy, bottle green, black of any size as approved by Engineer-in-

Charge in skirting, risers of steps and dados over 12 mm thick bed of cement

Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg

per sqm including pointing in white cement mixed with pigment of matching shade

complete. sqm 10.00 1112.70 11,127

GRANITE WORK FOR COUNTER

6.8 8.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and

prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias

and similar locations of required size, approved shade, colour and texture laid over

20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated

with white cement, mixed with matching pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to edges to give high gloss finish etc.

complete at all levels.

a) 8.2.2.2 Area of Slab over 0.50sqm sqm 10.00 5136.30 51,363

6.9 8.3 Extra for providing edge moulding to 18mm thick marble stone counters, Vanities

etc. including machine polishing to edge to give high gloss finish etc. complete as

per design approved by Engineer-in-Charge.

8.3.2 Granite work. metre 10.00 510.95 5,110

6.10 8.5 Extra for providing opening of required size & shape for wash basins/ kitchen sink in

kitchen platform, vanity counters and similar location in marble/Granite/stone work

including necessary holes for pillar taps etc. including rubbing and polishing of cut

edges etc. complete. each 5 978.70 4,894

FLOORING WORK TOTAL 20,52,446 29,040

7.0 SUB HEAD-VII :- PAINTING AND FINISHING WORK

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

7.1 13.16 6 mm cement plaster of mix :

13.16.1 1:3 (1 cement : 3 fine sand) sqm 50.00 300.45 15,023

7.2 13.4 12mm cement plaster of mix :

13.4.2 1:6 (1 cement: 6 coarse sand) sqm #### 343.65 82,476

7.3 13.5 15 mm cement plaster on the rough side of single or half brick wall of mix :

13.5.2 1:6 (1 cement: 6 coarse sand) sqm #### 395.35 94,884

7.4 13.80 Providing and applying white cement based putty of average thickness 1 mm, of

approved brand and manufacturer, over the plastered wall surface to prepare the

surface even and smooth complete. sqm #### 156.05 82,707

7.5 13.41 Distempering with oil bound washable distemper of pproved brand and manufacture

to give an even shade :

13.41.1 New work (two or more coats) over and including water thinnable priming coat with

cement primer sqm #### 185.65 44,556

7.6 13.62 Painting with synthetic enamel paint of approved brand and manufacture of

required color to give an shade.

13.62.1 Two or more coats on new work including priming coat of ordinary paint approved

brand. sqm 50.00 140.25 7,013

7.7 13.47.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of

required shade:

New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming

coat of exterior primer applied @ 2.20 kg/10 sqm) sqm #### 171.10 41,064

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

7.8 NSR Providing & fixing galvanized low carbon wire, anealed wire Chicken mesh formed

by twisting two adjacent wires at least four times, forming a hexagonal shaped

strong honeycomb mesh structure on joints of RCC & Brick work before plastering,

of required gauge (not less than 21 gauge)and size with nails etc. complete as

specified in drawing and as per the Direction of Engineer-in-charge.

7.9 13.45 Finishing walls with textured exterior paint of required shade :

13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including

priming coat of exterior primer applied @ 2.20kg/10 sqm sqm #### 223.60 53,664

7.10 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of

approved brand and manufacture, including providing and fixing top & bottom pivot

& double acting hydraulic floor spring type fixing arrangement and making

necessary holes etc. for fixing required door fittings, all complete as per direction of

Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

7.11 NSR Providing and fixing 12 mm thick frameless toughened glass partitions of approved

brand and manufacturer, including providing and fixing partitions at top & bottom

with aluminum channel etc. all complete as per direction of Engineer-in-charge

7.12 NSR Providing and fixing approved brand and manufacture SS 304 grade D type

1200mm Pull Handle with 32mm dia fixed with SS screws etc. complete in all

respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

7.13 NSR Providing and fixing approved brand and manufacture SS 304 grade Glass door

Lock, top and bottom patch fitting with SS screws etc. complete in all respects as

per manufacturers' specifications & as directed by Engineer-in-charge.

PAINTING AND FINISHING WORK TOTAL 7,16,653 18,35,100

8.0 SUB HEAD-VIII :- WATER PROOFING

8.1 22.7 Providing and laying integral cement based water proofing treatment including

preparation of surface as required for treatment of roofs, balconies, terraces etc

consisting of following operations: a) Applying a slurry coat of neat cement using

2.75 kg/sqm of cement admixed with water proofing compound conforming to IS.

2645 and approved by Engineer-in-charge over the RCC slab including adjoining

walls upto 300 mm height including cleaning the surface before treatment. b)

Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size

with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water

proofing compound conforming to IS : 2645 and approved by Engineer-in-charge

over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand )

admixed with water proofing compound conforming to IS : 2645 and approved by

Engineer-in-charge to required slope and treating similarly the adjoining walls upto

300 mm height including rounding of junctions of walls and slabs c) After two days

of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of

cement admixed with water proofing compound conforming to IS : 2645 and

approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick joint

less cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water

proofing compound conforming to IS : 2645 and approved by Engineer-in-charge

including laying glass fibre cloth of approved quality in top layer of plaster and

finally finishing the surface with trowel with neat cement slurry and making pattern

of 300x300mm square 3 mm deep. e) The whole terrace so finished shall be flooded

with water for a minimum period of two weeks for curing and for final test. All

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Providing and laying integral cement based water proofing treatment including

preparation of surface as required for treatment of roofs, balconies, terraces etc

consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed

with water proofing compound conforming to IS. 2645 and approved by Engineer-in-

charge over the RCC slab including adjoining walls upto 300 mm height including

cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm

size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water

proofing compound conforming to IS : 2645 and approved by Engineer-in-charge

over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand)

admixed with water proofing compound conforming to IS : 2645 and approved by

Engineer-in-charge to required slope and treating similarly the adjoining walls upto

300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using

2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS :

2645 and approved by Engineerin-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1

cement :4 coarse sand) admixed with water proofing compound conforming to IS :

2645 and approved by Engineerin-charge including laying glass fibre cloth of

approved quality in top layer of plaster and finally finishing the surface with trowel

with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period

of two weeks for curing and for final test. All above operations to be done in order

and as directed and specified by the Engineer-in-Charge :

22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65mm.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

22.5 Providing and laying water proofing treatment in sunken portion of WCs,

bathroom etc., by applying cement slurry mixed with water proofing

cement compound consisting of applying:

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water

proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed

to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water

proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to

air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all

joints, corners, junctions of pipes and masonry with polymer mixed slurry. sqm 30 617.0 5 18,512

8.2 NSR Metal Roof Waterproofing with Polyurethane based liquid membrane

Cleaning: Thoroughly clean the surface with wire brush properly to remove all

laitance, dust, etc. Sheet Joint & J-Hooks Treatment: Treatment of metal sheet

joints & J-hooks by using silicone sealant HS JointSeal Super GP and with the help

of hoisin cloths dipped in HS Elastoseal BTD etc. complete as per manufacturer

recommendations. Primer Application: Providing and applying one coat of HS Epoxy

Primer @0.150 gm/Sqm over the cleaned metal surface. Liquid Applied Membrane

Application: Providing and applying two coats of HS Elastoseal BTD a water-based,

single component UV resistant elastomeric PU liquid membrane in white / terracotta

/ green colour. better UV resistance, we recommend use of white colour BTD,

having SRI Index > 109, having solid content 80%, Elongation 400%, Tensile 2MPa,

with the help of brush/Roller with the coverage of 1.8Kg/Sqm to achieve DFT of

1mm, Sandwich 40GSM fibre-mesh in between two coats over the metal joints, etc.

complete as per manufacturer recommendations.

WATER PROOFING WORK TOTAL 18,512 78,450

9.0 SUB HEAD-IX :- LGSF -PRE FAB STRUCTURE WORKS:

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

9.1 NSR Design, Supply, installation , erection ,testing and commissioning of super

structure of LGSF Prefab structure technonogy based Laboratory on the roof of

Center for interdisciplinary research (including all the civil and electrical works

necessary for successful installation and commissioning of the MEP work as

per site requirement & approved drawing) as per Engineer In-charge and below

mentioned specifications. Scope Includes designig of LGSF structural system with

Structural vetting from IIT/NIT as approved by Engineer Incharge.

(1) Primary Steel Structure:-Built up section with fabricated Plates having

minimum yield strength of 250 MPa and will conform to IS: 2062 / ASTM-A-572-12

Grade 50 Standard. The built-up members would be fabricated by continuous shop

automated welding using submerged arc welding. Members fabricated from plate

will have flanges and webs joined both sides by a continuous welding process. All

built up members shall have one coat of red oxide primer and final coat of synthetic

enamel paint of RAL 5017 having total paint thickness > 120 micron. All

connections (Fasteners/J bolts, etc.) shall be as perapproved design drawings. (2)

LGSF walls (Load bearing/ Non load bearing):Structural Members (LGSF)

consist of Mild steel Galvanized Structure with the yield strength not less than 550

MPa and AZ 150 zinc coated/Equivalent. 89 mm x 41mm flange x 11mm lip in

required length as per structural design requirement duly punched with dimple/slot

at required locations (3) External Wall Cladding System:High-density Fiber

cement boards 9mm HD FCB Type A) and a facia sheet of 6mm HD FCB board on

the primary layer as per standard dimension fixed with self-drilling / taping screws /

fasteners @ 60cm c/c of approved make. 2-3mm groove pattern shall be given

through out the exterior wall. (4) Internal Wall Cladding System:1. Interior

walls: Main Area: 12.5 mm thick Gypsum board for a better interior finish applied

on 8mm standard Fiber cement board category III type B as per standard sizes

fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make,

Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic

based jointing compound for seamless finish. A grove of 2 mm to 3mm shall be

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

(7) Painting: Wall painting (Internal), two (2) coats of plastic emulsion type paint

is applied on top of one coat of primer and putty on undecorated wall surfaces to

give an even shade including thoroughly brushing the surface free from mortar

droppings and other foreign matter and sand papered smooth including applying of

putty as required for making the surface. Wall painting (External), two (2) coats of

weatherproof paint one primer and putty (excluding priming coat) on undecorated

wall surfaces to give an even shade including thoroughly brushing the surface free

from mortar droppings and other foreign matter and sand papered smooth including

applying of putty as required for making the surface.

(8) False Ceiling: Dry are as: 12.5mm thick Suspended Gypsum board false

ceiling on edges as band and 600x600 Mineral Fibre Tile Ceiling in remaining areas

with all necessary hanging arrangement and accessories. Wet areas: Calcium

Silicate made 12.5 mm thick false ceiling as per CPWD specifications owith all

necessary hanging arrangement and accessorier.

(9) Doors: Rooms: Single/double Aluminum frame door with both side laminated

35mm thick flush door shutter in different Sizes as per approved architectural

drawings. The doors shall be complete with SS hardwares like Mortise lock,

Handle, Tower Bolt, Flush bolts, etc. shall also be provided as per approved

drawings.

(10) Windows:Providing and fixing factory made uPVC white color sliding glazed

window comprising of uPVC multi-chambered frame with in-built roller track and sqm #### 34982.90 - 2,53,63,650

sash extruded profiles duly reinforced with 1.20 ± 0.2 mm thick galvanized mild

LGSF WORKS: TOTAL 2,53,63,650

10 DEMOLITION WORK

15.7.4 Demolishing brick work manually/ by mechanical means including stacking of

serviceable material and disposal of unserviceable material within 50 metres lead as

per direction of Engineer-in-charge.-In cement mortar cum 2060.20 Cum 38 2060.2 78,288

DEMOLITION WORKS: TOTAL 78,288

BOQ OF CIR BUILDING

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

ELECTRICAL WORK

S. H.- INTERNAL ELECTRICAL WORK

1.0 1.10 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable in surface / recessed

medium class PVC conduit, with modular switch, modular plate, suitable GI box and

earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core

cable etc. as required.

1.1 1.10.3 Group C Point 49 1 467 71,883

2.0 1.55 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell

point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed PVC conduit, and earthing the point

with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as

required.

2.1 1.55.3 Group C Point 29 858 24,882

3.0 1.12 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor

single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4

sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as

required. Meter 600 `

4.0 1.13 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor

single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4

sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as

required. Metre 300 537 1,61,100

5.0 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of

FRLS PVC insulated copper conductor, single core cable in surface/ recessed

medium class PVC conduit as required. -

CIRCUIT / SUBMAIN WIRING -

5.1 1.14.1 2x1.5 sq mm + 1x1.5 sq mm earth wire Meter 500 233 1,16,500

5.2 1.14.2 2x2.5 sq mm + 1x2.5 sq mm earth wire Meter 500 275 1,37,500

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

5.3 1.14.5 2x10 sq. mm + 1x6 sq. mm earth wire Meter 500 570 2,85,000

5.4 1.14.10 4x10 sq mm + 2x6 sq mm earth wire Meter 220 1 005 2,21,100

5.5 1.14.11 4x16 sq mm + 2x6 sq mm earth wire Meter 150 1 365 2,04,750

6.0 1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on

surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket

outlet and 5/6 amps modular switch, connection etc. as required. Each 20 477 9,540

7.0 1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on

surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular

socket outlet and 15/16 amps modular switch, connection etc. as required.

8.0 1.56 Supplying and fixing suitable size GI box with modular plate and cover in front on

surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket

outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light

plugs to be used in non residential buildings). (For UPS Supply)

9.0 1.27 Supplying and fixing following size/ modules, GI box alongwith modular base &

cover plate for modular switches in recess etc as required. -

9.1 1.27.1 1 or 2 Module (75mmX75mm) - For Telephone,TV outlet & Data Each 10 298 2,980

9.2 1.27.2 3 Module (100mmX75mm) - For Socket outlet. Each 10 327 3,270

9.3 1.27.3 6 Module (200mmX75mm) - For Socket outlet. Each 8 343 2,744

9.4 1.27.5 8 Module (125 mmX125 mm) Each 6 454 2,724

9.5 1.27.6 12 Module (200 mmX150 mm) Each 5 547 2,735

10.0 2.3 Supplying and fixing following way, single pole and neutral, sheet steel, MCB

distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar,

neutral bus bar, earthbar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator) -

10.1 2.3.3 12 Way, Double Door Each 2 2 315 4,630

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

11.0 2.4 Supplying and fixing following way, horizontal type three pole and neutral, sheet

steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned

copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder

painted including earthing etc. as required. (But without MCB/RCCB/Isolator).

11.1 2.4.3 8 Way (4+24), Double Door Each 2 5 967 11,934

12.0 2.5 Supplying and fixing of following ways surface/ recess mounting, vertical type,

415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder

painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth

bar, din bar for mounting MCB's (but without MCB's and incomer ) as required.

12.1 2.5.3 12 way (4 + 36), Double door Each 1 12 833 12,833

13.0 2.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, C series Miniature

Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB

complete with connections, testing and commissioning etc,as required.

13.1 2.10.1 Single pole Each 82 256 20,992

15.0 NON DSR Supplying and fixing following rating, double pole, 240 volts, MCB complete with

connections, testing and commissioning etc. as required.

15.1 NON DSR 40 Amp Each 2 1 253 2,506

16.0 NON DSR Supplying and fixing following rating, four pole, 415 volts, MCB complete with

connections, testing and commissioning etc. as required. -

16.1 NON DSR 40 Amp Each 2 2 402 4,804

16.2 NON DSR 63 Amp Each 1 2 568 2,568

17.0 2.14 Supplying and fixing of following rating double pole (Single phase and neutral) 240

volts, residual current circuit breaker (RCCB), having a current sensivity current 30

miliampere in the existing MCB DB complete with connections, testing &

commissioning etc. as required.

17.1 2.14.2 40 Amp Each 8 2 642 21,136

17.2 2.14.3 63 Amp Each 3 2 722 8,166

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

18.0 1.21 Supplying and fixing of following sizes of medium class PVC conduit along with

accessories in surface/recess including cutting the wall and making good the same

in case of recessed conduit as required. -

18.1 1.21.2 25 mm Metre 500 145 72,500

18.2 1.21.3 32 mm Metre 100 184 18,400

19.0 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch

box excluding modular plate as required. Each 6 40 240

20.0 2.23 Supplying and fixing Cable End Box (Loose wire box) (IP 43) suitable for following

single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/

recess, complete with testing and commissioning etc. as required. -

20.1 2.23.4 For 14 way, Double door SPN MCBDB Set 2 902 1,804

21.0 2.24 Supplying and fixing Cable End Box (Loose wire box) (IP 43) suitable for following

triple pole and neutral, sheet steel, MCB distribution board, 415V, on surface/

recess, complete with testing and commissioning etc. as required. -

21.1 2.24.3 For 8way, Double door TPN MCBDB Set 3 1 340 4,020

22.0 1.41 Installation, testing and commissioning of pre-wired, fluorescent fitting / compact

fluorescent fitting/ LED fittings of all types, complete with all accessories and

tube/lamp/ LED etc. directly on ceiling/ wall/ false ceiling with GI Chain included for

fixing wherever required, including connections with 1.5 sq. mm FRLS PVC

insulated, copper conductor, single core cable and earthing etc. as required.

23.0 1.57 Supplying & fixing suitable size GI box wih modular plate and cover in front on

surface or in recess including providing and fixing 25 A modular socket outlet (near

equipment point) and 25 A modular SP MCB, “C” curve (at accessible point)

including connections, painting etc. as required. Each 1 727 727

24.0 NON DSR Supply of following sizes of ISI marked aluminium conductor XLPE insulated cable

as per IS 7098, armoured, served, sheathed 1100 volts grade. (Cable shall be

purchased only after approval of cable schedule by architect / consultant).

24.1 NON DSR 3.5 core, 150 sq.mm. Meter 200 1 890 3,78,000

24.2 NON DSR 4 core, 16 sq.mm Meter 310 376 1,16,560

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

24.3 NON DSR 4 core, 10 sq.mm Meter 204 352 71,808

24.4 NON DSR 4 core, 6 sq.mm Meter 100 256 25,600

24.5 NON DSR 2 core, 16 sq.mm Meter 110 282 31,020

24.6 NON DSR 2 core, 10 sq.mm Meter 100 248 24,800

24.7 NON DSR 2 core, 6 sq.mm Meter 100 196 19,600

25.0 NON DSR Supplying and fixing following rating, four pole, 415 volts, MCB with inclousre

complete with connections, testing and commissioning etc. as required. -

25.1 NON DSR 40 Amp Each 4 2 942 11,768

25.2 NON DSR 63 Amp Each 6 3 120 18,720

26.0 7.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1

KV grade of following size direct in ground including excavation, sand cushioning,

protective covering and refilling the trench etc as required.

26.1 7.1.1 Upto 35 sq. mm Meter 10 387 3,870

26.2 7.1.2 Above 35 sq. mm and upto 95 sq. mm Meter 200 405 81,000

27.0 7.50 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1

KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

27.1 7.5.1 Upto 35 sq. mm Metre 150 37 5,550

28.0 7.8 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power

cable of 1.1 KV grade of following size on cable tray as required. -

28.1 7.8.1 Upto 35 sq. mm (clamped with cable tie) Meter 455 45 20,475

29.0 9.1 Supplying and making end termination with brass compression gland and aluminium

lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium

conductor cable of 1.1 KV grade as required. -

29.1 9.1.1 2 x 6 sq. mm (19mm) Each 2 240 480

29.2 9.1.2 2 x 10 sq. mm (19mm) Each 2 241 482

29.3 9.1.3 2 X 16 sq. mm (22mm) Each 2 256 512

29.4 9.1.26 3½ X 150 sq. mm (50mm) Each 2 697 1,394

29.5 9.1.32 4 X 10 sq. mm (25mm) (The Termination including 4 x 6 sq. mm cable) Each 14 269 3,766

29.6 9.1.33 4 X 16 sq. mm (28mm) Each 30 309 9,270

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

30.0 4.6 Supplying and installing following size of perforated Hot Dipped Galvanised Iron

cable tray (Galvanisation thickness not less than 50 microns) with perforation not

more than 17.5%, in convenient sections, joined with connectors, suspended from

the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

30.1 4.6.1 100 mm wide x 50 mm depth x 1.6 mm thickness. Meter 34 669 22,746

30.2 4.6.4 300 mm wide x 50 mm depth x 1.6 mm thickness. Meter 20 963 19,260

31.0 4.7 Supplying and installing following size of perforated Hot Dipped Galvanised Iron

cable tray "bends" (galvanisation not less than 50 microns) with perforation not

more than 17.5%, in convenient sections, joined with connectors, suspended from

the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

31.1 4.7.1 100 mm wide x 50 mm depth x 1.6 mm thickness. Each 6 1 159 6,954

31.2 4.7.4 300 mm wide x 50 mm depth x 1.6 mm thickness. Each 4 1 852 7,408

32.0 4.8 Supplying and installing following size of perforated Hot Dipped Galvanised Iron

cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more

than 17.5%, in convenient sections, joined with connectors, suspended from the

ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

32.1 4.8.1 100 mm wide x 50 mm depth x 1.6 mm thickness. Each 6 1 327 7,962

32.2 4.8.4 300 mm wide x 50 mm depth x 1.6 mm thickness. Each 4 2 156 8,624

33.0 4.9 Supplying and installing following size of perforated Hot Dipped Galvanised Iron

cable tray "Cross member"(galvanisation not less than 50 microns) with perforation

not more than 17.5%, in convenient sections, joined with connectors, suspended

from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required.

33.1 4.9.1 100 mm wide x 50 mm depth x 1.6 mm thickness. Each 6 1 327 7,962

33.2 4.9.4 300 mm wide x 50 mm depth x 1.6 mm thickness. Each 4 2 366 9,464

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

34.0 4.10 Supplying and installing following size of perforated Hot Dipped Galvanised Iron

cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not

more than 17.5%, in convenient sections, joined with connectors, suspended from

the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

34.1 4.10.1 100 mm wide x 50 mm depth x 1.6 mm thickness. Each 6 1 655 9,930

34.2 4.10.4 300 mm wide x 50 mm depth x 1.6 mm thickness. Each 4 2 823 11,292

35.0 Supplying and laying of following size DWC HDPE pipe ISI marked along with all

accessories like socket, bend, couplers etc. conforming to IS 14930, Part II

complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground

level) including excavation and refilling the trench but excluding sand cushioning

and protective covering etc., complete as required. -

35.1 14.16.3 120 mm dia (OD-120 mm & ID-103 mm nominal) Meter 20 368 7,360

35.2 14.16.5 200 mm dia (OD-200 mm & ID-175 mm nominal) Meter 20 668 13,360

36.0 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including

accessories, and providing masonry enclosure with cover plate having locking

arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt

as required. Each 2 7 472 14,944

36.1 Supply, Installation, Testing & Commissioning of Earthing with copper earth

plate 600 mm X 600mm X 3 mm thick including accessories, and providing

masonry enclosure with cover plate having locking arrangement and watering Nos. 4 13838

pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

37.0 5.1 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for

connections etc. as required. Metre 170 1 162 1,97,540

37.1 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for

connections etc. as required. Meter 200 244 48,800

38.1 1.53 Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface/

recessed Steel/ PVC conduit as required. -

38.2 1.53.1 1 run of cable Metre 300 57 17,100

38.3 1.53.2 2 run of cable Metre 200 96 19,200

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

TOTAL FOR S.H.-I 20,70,601 7,07,754

S. H.- LIGHT FIXTURE & POLES

1.0 NON DSR Supply of LED indoor surface downlighter suitable for general lighting. Luminaire

should have pressure die-cast Al housing with diffused optics. The luminaire should

have CRI > 80 and CCT of 6500K. The luminaire shall be compliant with IP20, IK02

classification.The fixture should have a minimum system efficacy >110 lumen/Watt

and a minimum system lumen output of 2150 lumens and maximum system

wattage of 18 Watts, ambient temp 45 deg C. The electronic driver used shall have

a power factor >0.95 , THD <10%.

2.0 NON DSR Supply of Recessed LED Downlighter ,made up of pressure die cast aluminum

housing with high efficiency Prismatic PS diffuser, LED Used shall be SMD type and

fixture should have minimum efficacy at System level >=100 lumens/watt with

Minimum system Lumens 1400 & max wattage 13.5W, Life of fixture : 50000

burning Hrs. @ L70B50 Lumen maintenance, CCT of 6500K (SDCM<=5), CRI Ra

>=80, PF >0.9, an Operating working temp range - 0°C < Ta < 45°C & operating

Voltage Range of 130-320 V AC. Minimum Internal Surge Protection 2.5KV. The

fixture design should be with flicker free operations ripple <5%, comply to

IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction

with IEC61347-1 ed.2.0, 2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for

performance and IEC61547 ed.2.0, 2009, CISPR-15 for EMI/EMC.

3.0 NON DSR Supply of LED Mirror batten light of 2ft length with a system wattage of 10-11W

with a nominal system lumen output of 1100-1200 lumens and a minimum system

efficacy of 110lm/W. CCT shall be 6500K and CRI ≥ 80. Housing shall be extruded

aluminimum with powder coating & with IP20 protection. The luminaire shall meet

IP20 rating with THD≤20% and PF ≥ 0.90.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

4.0 NON DSR Supply of of recessed mounted 2X2 LED panel ,made of CRCA housing with high

efficiency PS Diffuser. LED Used shall be SMD type and fixture should have

minimum efficacy at System level >=120 lumens/watt with Minimum system

Lumens 4300 & Max System wattage of 36W, Life of fixture : 50000 burning Hrs.

@ L70B50 Lumen maintenance,CCT-6500K, (SDCM<=5), CRI Ra >=80, THD<10%,

PF >0.95, an operating Voltage Range of 140 - 270 VAC.Minimum Internal Surge

Protection 4.0KV & IP20/IK02 protection, Fixture should comply with to IEC61000-

3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction with

IEC61347-1 ed.2.0, 2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for

performance and IEC61547 ed.2.0, 2009, IEC 60598-2-2, CISPER 15 for EMC /

EMI compliance with flicker free operations ripple <5%.

5.0 NON DSR Supply of Heavy duty bulkhead surface type lighting fixture 10W - 1100lm made up

of pressure die-cast aluminium housing and Polyster Powder coated die cast

aluminium with High quality polycarbonate diffuser in opal finish for glare free light

distribution.High efficiency long life LED module with SMD LED package mounted on

MCPCB with lumen efficacy of >100 lm/W. Powered by integral electronic LED driver

with CCT 6500, CRI>80,THD<10%, PF>0.9, IP66, IK 09, Life class of 50,000 hrs @

L70, Operating Temperature: 0 TO +45 DEG.C; Input Supply Voltage Range:140-

270 V, Frequency :50-60 HZ. Nos. 1 2 462 2,462

6.0 19.1 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star

rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation:

B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope,

copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum

6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-

2019), THD less than 10%, remote or electronic regulator unit for speed control and

all remaining accessories including safety pin, nut bolts, washers, temperature

rise=75 degree C (max.), insulation resistance washers, temperature rise=75

degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V,

50 Hz, single phase AC Supply, earthing etc. complete as required.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

7.0 NON DSR Supply, Installation, Testing and Commissioning of 250 mm sweep decorative

Fresh air fan with all accessories suitable for operation single phase 230 volt 50

cycle per second per sec. AC supply etc. as required. in the existing opening,

including making the hole to suit the size of the above fan, making good the

damage, connection, testing, commissioning earthing etc. as required.

TOTAL FOR S.H.-II 49,815 3,13,230

S.H.- DATA, TELEPHONE SYSTEM INCLUDING ACTIVE COMPONENTS

1.0 NON DSR Supply, Installation, Testing & Commissioning of Patch Panel Cat 6 U/FTP 24 Port-

Loaded as per technical specification. Nos. 1 16195 16,195

2.0 NON DSR Supply, Installation, Testing & Commissioning of Patch Cord Cat 6 U/FTP 3 feet as

per technical specification. Nos. 10 447 4,470

3.0 NON DSR Supply, Installation, Testing & Commissioning of Patch Cord Cat 6 U/FTP 7 feet as

per technical specification. Nos. 2 1005 2,010

4.0 NON DSR Supply, Installation, Testing, Commissioning of Cat 6, 10G, U/FTP, Information

Outlet including G.I. Box and modular cover plate as per technical specification.

5.0 NON DSR Supply , Installtion , Testing and comissioning of 12U wall mount rack with fans ,

2 cable managers, satationary shelf , 2 Nos of hardware pkts as per technical

specification. Nos 1 20104 20,104

6.0 NON DSR Supply, Installation, Testing & Commissioning of 24 port 10/100/1000Mbps, 4SFP

module, L-2 Switch, POE as per technical specifications. Each 1 75949 75,949

7.0 NON DSR Supply, Installation, Testing & Commissioning of Type Basic Phone account , Full

duplex speaker phone, . Nos 2 3574 7,148

8.0 NON DSR Supply, Installation, Testing & Commissioning of SFP+ 10GBASE-SR 10

Gigabit Ethernet Optics, 850 nm for up to 300 m,transmission on multimode fiber

(MMF). Nos 1 53053 53,053

9.0 NON DSR Supply, Installation, Testing & Commissioning of 6 Core OM4 Multimode

Fiber Cable as per technical specification. Meter 30 335 10,050

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

10.0 NON DSR Supply, Installation, Testing & Commissioning of 24 Port LC multimode

loaded LIU. Nos 4 12844 51,376

11.0 NON DSR Supply, Installation, Testing & Commissioning of LC - LC Fiber patch cord

OM4, 3 Mtrs. Nos 4 15637 62,548

12.0 NON DSR Supply, Installation, Testing & Commissioning of 6 Core, Single Mode, OS2 as

complete as required. Meter 60 279 16,740

TOTAL FOR S.H.-III - 3,31,031

S.H.- IP CCTV SYSTEM

1.0 NON DSR Supply, Installation, Testing & Commissioning of 4MP IP Network TDN Low-Light IR

Rugged Indoor Dome Camera, 1/2.8" CMOS or better, 4MP (2304 x 1296) @ 25fps

or better, triple stream at various resolution up to 25fps, Min. Illumination required

0.005 lux @ F1.6 (color), 0 Lux IR On, 4 IR LEDs Smart IR with upto 50m IR

distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter

Speed 1/8 - 1/30,000; Adavance Video Compression technology such as H.265 &

H.264 High Profile & MJPEG , Triple stream, 2.7 to 13.5mm 5X motorized focus &

zoom lens, Field of View FoV H:88°-24°, BLC, HLC, 3DNR White Balance, Minimum

Edge Intelligence Video Analytics : Motion Detection, Tampering, 4 Privacy Mask, 8

Region Of Intreset, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption,

256GB SD card support, PoE (802.3 af) and 12V DC, Max 6W, IP 66/67, IK 10

vandal proof with Die Cast Aluminium Housing, Having Operating temp range :

–40°C to 60° C. Certifications: ONVIF Profile S/G/T compliant, UL/CSA 62368-1, CE

(EN 50130-4), FCC Part 15, EN 55032 & RoHS (EN63000) compliant

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

2.0 NON DSR Supply , Installation , Testing and commissioning of 16 Channel NVR (Network

Vedio Recorder), for recording upto 64CH @ 1080P with 08 nos. SATA HDDs

minimum 64TB storage or more (recording requirement all cameras recording at

4MP, 25fps for 30 days),H.265/H.264/MJPEG/MPEG4 codec decoding, Front Control

Pannel with LEDs Indication, 3 nos. USB, iPhone; iPad; Android based Mobile

clients, Video Export feature on USB, Search Mode: Time/Date; Alarm; Motion

Detection (MD); Exact Search (accurate to a second); Smart Search, Dual HDMI

Output, Alarm Input (16 nos.), Alarm Output (6 nos.), 16 POE Ports, eSATA

Device, 320Mbps each Incoiming & Outgping throughput, Operating Temperature

–10°C to 55°CCertification : CE, FCC & UL including fixing accessories and cable

termination with required connectors/Jack, complete in all respect as per instruction

of engineer in-charge Nos 1 295979 2,95,979

3.0 NON DSR Supply, Installation, Testing and commissioning of Managable 24 port Switch with

Power on Ethernet (PoE) enabled, 10/100, RJ45 Access ports with PoE complete as

required. Nos 1 54170 54,170

4.0 NON DSR Supply, Installation, Testing and Commissioning of pecial Surveillance 6TB SATA

HDD internal( For Servers). etc. all complete. Nos 1 27364 27,364

5.0 NON DSR Supply, Installation, Testing and Commissioning of 55" LCD for Monitoring for

each server etc. all complete. Nos 1 72599 72,599

TOTAL FOR S.H.-IV - 6,33,280

S.H.- UPS SYSTEM

1.0 NON DSR Supply, Installation, Testing & Commissioing of 10 KVA UPS in paralleling mode at

0.99 input power factor with SNMP card, compatible for BMS connectivity on

backnet/MODBUS, Inbuilt Isolation transformer as per specification given in the

document with following broad features.

a) THD(i) shall be less than 3% in the entire loading range.

b) UPS shall carry design output at 40 deg.

c) Shall have soft start and hold of for incoming supply.

d) Invertor capability to supply 150% load for 5 sec.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

e) Single Phase Input and Single Phase Output. (Input - 220V - 240V, Single Phase, 2

wire. / Output - 220-225 Volt, Single Phase, 2 Wire.)

f) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case

of 12 volt cells.

g) Battery shall be external type with rack and suitable for 30 minute backup on 100%

h) Suitable size of copper cable between UPS and battery bank shall be provided

i) UPS shall be compatible for 3 nos unit in parallel operation. (Synchronize). Parallel

operation kit shall be supplied with UPS.

UPS described as above with online 3 phase UPS system with 30 minutes back up

including batteries, interconnecting cables, battery racks etc. all complete Each 1 6 59 202 6,59,202

TOTAL FOR S.H.-V - 6,59,202

S.H.- SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

1.0 6.8.1 Supplying installation testing and commissioning of Grid interactive roof top solar

(PAR- photo voltaic power generation system including all the required accessories like

2023) Solar PV module, Grid Tie invertor, arrey junction box, cabling & wiring, earthing,

surge protection device, FRLSame structure for mounting of solar panel. The cell

shall be poly crystaline silicon cells of 6 inch each and module efficiency shall be

more than 17%. Solar module shall have linear output warranty with degradation

not exceeding 0.7% FRLSom 2nd Year onwards. Minimum 80% power output must

be assured at end of 25 years. The FRLSont glass of solar module shall be low iron

tempered glass ARC type. Termination box shall be Thermo-plastic, IP 67 or better,

UV resistant with built-in-bypass. The nominal power of a single PV module shall be

minimum 545 Wp or higher. Positive power tolerance modules only to be used. RF

identification tag for each solar module shall be provided inside the module and

must be able to withstand environmental conditions. The solar panel shall be

complience of IEC 61215, IEC 61730 certified by TUV Rheinland / UL. The solar

panel shall be installed as per BOQ & detailed technical specification as below:

Roof top grid interactive solar photo voltaic plant system shall be

inclusive of the Solar panels of prescribed efficiency, mounting

structure, cabling, inverter , panel, metering devices, earthing,

lightning protection complete as per state-of-the-art technology as

per good engineering practice compliant to relevant Indian standards/

local/statutory authorities/MNRE guidelines.; KWp 25 58480 14,62,000

High efficiency PV cells with high efficiency invertors shall be used.

TOTAL FOR S.H.-VI 14,62,000 -

S. H. FIRE ALARM SYSTEM (ADDRESSABLE TYPE)

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

1.0 17.2.1 Supplying, installation, testing and commissioning of micro processor based

intelligent addressable main fire alarm panel, central processing unit with the

following loop modules and capable of supporting not less than 240 devices

(including detectors) and minimum 120 detectors per loop and loop length up to 2

km, network communication card, minimum 320 character graphics/ LCD display

with touch screen or other keypad and minimum 4000 events history log in the non

volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up

with 24 volt sealed maintenance free batteries with automatic charger. The panel

shall have facility to connect printer to printout log and facility to have seamless

integration with analog/digital voice evacuation system (which is part of the

The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus

over IP complete as per specifications.

1.1 17.2.1.1 Two Loop Panel Each 1 239225 2,39,225

2.0 17.2.2 Supplying, installation, testing & commissioning of central graphical fire alarm

management system to centrally monitor and operate the fire alarm system

complete as required. Each 1 200611 2,00,611

3.0 17.2.4 Supplying, installation, testing & commissioning of intelligent analog addressable

photothermal detector complete with mounting base complete as required.

4.0 17.2.9 Supplying, installation, testing & commissioning of intelligent addressable thermal

detector with rate of rise cum fixed tempreature thermistor complete with base as

required. Each 1 2726 2,726

5.0 17.2.14 Supplying, installation, testing & commissioning of addressable manual call point

complete as required. Each 1 3871 3,871

6.0 17.2.15 Supplying, installation, testing & commissioning of addressable horn cum strobe

complete as required. (75 DBA @3 mtr. & 75CD flashing) Each 1 3506 3,506

7.0 17.2.7 Supplying, installation, testing & commissioning of fault isolator complete with base

as required. Each 1 3270 3,270

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

8.0 17.2.5 Supplying, installation, testing & commissioning of response indicator on

surface/recessed MS Box having two LED, metallic cover complete with all

connections etc as required. Each 4 276 1,104

9.0 17.5.2 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with

annealed copper conductor having XLPE insulation, steel wire armouring & FRLS

outer sheath complete as required. Metre 200 143 28,540

TOTAL FOR S.H.-VI 5,13,549 -

S.H.- DISTRIBUTION PANEL

1 supply, installation, testing and commissioning of cubicle type totally enclosed free

standing type moisture, dust and vermin proof Floor Distribution Panel made out of

2.0 mm thick & front cover 1.6 mm thick CRCA sheet complete with following

wiring with suitable size wires / cable, interconnection, painting complete as per

specification & drawing. All the incomming and outgoing MCCB shall have 25 KA

Ics.The incoming MCCB shall be microprocessor based with O/L & S/C and E/F

protection and all Outgoings up to 250A MCCB's may be thermo-magnetic based

O/L & S/C protection. All outgoing MCB's shall be C type with 10 KA breaking

capacity.

1.1 NON DSR ELECTRICAL PANEL ( GROUND FLOOR)

INCOMING

2 No- 400AMP

1 Nos. 250 Amp FP MCCB (25 KA)

1 Nos. 100 Amp FP MCCB (25 KA) with meter for Solar

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

BUSBAR

400 Amp FP aluminium busbar with coloured heat shrinkable sleeve.

OUTGOING

02 Nos. 100 Amp

03 Nos. 63 Amp FP MCB

02 Nos. 25 Amp FP MCB (10 KA)

10 Nos. 40 Amp FP MCB (10 KA)

12 Nos. 63 Amp FP MCB (10 KA)

03 Nos. 63 Amp DP MCB (10 KA)

03 Nos. 63 Amp FP RCCB (300mA)

Panel described as above Set 2 461441 9,22,882

1.2 NSR Supply, Installaion, Testing & Commissioning of aluminum conductor XLPE

armored served sheathed cable 1100 Volts grade at a suitable depth of 1000

mm below ground level over cushion of 75 mm thick sand all around and

protected with well burnt bricks on sides & on top along the cable & back filling after

digging the soil & its back filling/ On wall/ floor the cable run canceled

manner, with cutting and plastering in hard rock / soft rock after excavation,

complete in all respect as per direction of Engineer in charge. If crossing the

cable in road/ rail line suitable boring to be done across the road/Rail Line/ cable

trenching machine and also suitable size of GI pipe to be fixed across the

road/rail line and also in pole cable terminated in suitable size of GI pipe. The

armouring of cable shall be properly connected with the earth terminal of the

panell F P and as required lugs, Gland and clamp etc properly fixed.

1.2.1 NSR 3.5C x 120 sq mm. Al Armoured cable Metre 200 1,408.00 2,81,600

1.2.2 NSR 3.5C 95 sq mm. Al Armoured cable Metre 200 1,258.00 2,51,600

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

2.2 NSR Supplying and making End Termination with brass compression gland for -

following size of PVC insulated and PVC sheathed / XLPE aluminium conductor

cable of 1.1 KV grade as required

2.2.1 NSR 3.5C x 120 sq mm. Al Armoured cable NO 48 220.0 10,560

2.2.2 NSR 3.5C 95 sq mm. Al Armoured cable NO 48 210.0 10,080

2.3 NSR Supplying and making end termination with aluminium lugs for following size of PVC -

insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV

grade as required

2.3.1 NSR 3.5C x 120 sq mm. Al Armoured cable NO 95 150.0 14,250

2.3.2 NSR 3.5C 95 sq mm. Al Armoured cable NO 95 120.0 11,400

2.4 NSR Supply and making End Termination of 120 / 95 Sq mm indoor cable with NO 18 5,143.00 92,574

heat shrinkable jointing kit complete with all accessories including lugs suitable for

3.5 core, XLPE aluminium conductor cable of 11 KV grade as required

2.5 Excavating trenches by mechinical / manual means of required width for pipes,

cables, etc including excavation for sockets, and dressing of sides, ramming of

bottoms, for all depth, including getting out the excavated soil, and then returning

the soil as required, in layers not exceeding 20 cm in depth, including consolidating

each deposited layer by ramming, watering, etc. and disposing of surplus excavated

soil as directed, within a lead of 50 m :,All kinds of soil,Pipes, cables etc. exceeding

DSR 2023- 80 mm dia. but not exceeding 300 mm dia

2.10.1.2 Metre 600 352.15 2,11,290

2.6 Filling available excavated earth (excluding rock) in trenches, plinth, sides of

DSR 2023- foundations etc. in layers not exceeding 20cm in depth, consolidating each

2.25 deposited layer by ramming and watering, lead up to 50 and for all lift. CUM 196 324 63,504

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

2.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse

sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III)

: 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1

cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal

size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse

sand) finished with floating coat of neat cement and making channels in cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

DSR 2023- nominal size) finished with a floating coat of neat cement complete as per standard

19.7 design : -

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) EACH 30 12,770.6 3,83,117

455x610 mm internal dimensions, total weight of cover and frame to be not less

DSR 2023- than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With common burnt

19.7.1.1 clay F.P.S. (non modular) bricks of class designation 7.5

TOTAL FOR S.H.-VI 6,57,911 15,94,946

PLUMBING SERVICES

A SUB HEAD - 1 : SANITARY FIXTURES

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole

basin mixer of approved quality and make, including painting of fittings and

1 17.7A brackets, cutting and making good the walls wherever required:- 7,921

a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass

single hole basin mixer Each 2 3960.55

Providing and fixing white vitreous china laboratory sink Size 450x300x150 mm

with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and

2 17.27 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting 30,153

of fittings and brackets, cutting and making good the wall wherever required :

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to

IS standards and weighing not less than 810 gms.

a) 18.50.1 15 mm nominal bore Each 14 820.70 11,490

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and

112 mm distance from wall of standard shape with bracket of the same materials

with snap fittings of approved quality and colour, weighing

not less than 105 gms. Each 12 168.35

5 17.70 Providing and fixing PTMT Bottle Trap for Wash basin, Sink and Urinal.

Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of

a) 17.70.2 tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 5,259

mm minimum water seal, weighing not less than 263 gms Each 14 375.65

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of

6 18.53.1 approved quality conforming to IS:8931 25,844

15 mm nominal bore Each 45 574.30

Providing and fixing testing and commissioning of storage type water heater

(Geyser) with automatic thermostatic control electric element, pressure release

valve, M.S. nuts and bolts etc. conforming to IS: 2082, including cutting holes &

making good the wall wherever required complete in all respects.

a) M.R. 15 Litres Capacity Each 2 13367 26,734

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Supply installation, testing and commissioning of self contained Drinking water

cooler confirming to IS : 1475 with ammendment no. 1 to 7, suitable for operation

on 230 volts ± 10% ,50 Hz,single phase A.C. supply. The tank and body casing of

the water cooler shall be made out of stainless steel . The water cooler will be of

8 M.R. following capacities with two numbers faucets / stop cocks: Nominal Storage

Capacity -120 Ltrs. cooling and storage capacity with inbuid RO Plant/system with

SS body and all connections water/electrical all complete in all respect.

Nominal cooling Capacity -120 Ltrs/ hrs. Each 1 192259 1,92,259

TOTAL OF SUB HEAD - 1 : SANITARY FIXTURES 82,687 2,18,993

B SUB HEAD - 2 : SOIL, WASTE AND RAIN WATER PIPES

Providing, fixing, testing and commissioning of UPVC SWR pipe type 'B' conforms

to IS : 13592-1992 with all fittings such as bends, tees, elbow, 'Y', offset, cleaning

pipe door, clamps etc. conforming to IS:14735-1999 and steel structural supports

etc. including cutting the floors, walls and making good the same in cement

1 M.R. concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical

characteristic conforms to IS : 13592-1992 type 'B'. The fitting dimension

conforming to IS : 14735-1999. The jointing to be completed with rubber ring

joint/solvent weld joint as required/applicable.

a) 110 mm (OD) Meter 65 1404 91,260

Providing & laying cement concrete 1:2:4 mix (1 cement : 2 coarse sand: 4 stone

aggregate 20mm and down gauge) 75mm in bed and pipe. For 100mm, 75mm and

50mm dia pipes under floor including cantering & shuttering wherever required.

Meter 65 2048 1,33,120

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Providing, fixing, testing and commissioning of UPVC 'P' trap/floor trap/urinal trap of

self cleansing design having 50 mm water seal with or without horn conforming to

IS : 14735-1999 including setting with cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 hard stone ballast 20 mm nominal size) including cost of cutting and

making good the walls & floors wherever required.

a) 110 mm inlet x110 mm outlet. Nos. 15 1328 19,920

Providing, fixing, testing and commissioning of UPVC inlet fittings (hopper) receive

waste from fixture waste with maximum 3 inlets 40, 50 & 63 mm OD size,

fabricated from 110 OD UPVC SWR pipe, UPVC sockets, fixed to UPVC traps

including solvent weld joint/rubber ring joint, complete with all civil work set in

cement concreate 1:2:4 as required including cost of cutting and making good the

walls & floors wherever required. Nos. 6 1009 6,054

Providing, fixing, testing and commissioning of UPVC cleanout plug conforming to

IS : 14735-1999 complete with all fitting; accessories and civil work.

a) 110 mm OD Nos. 6 355 2,130

Providing, fixing, testing and commissioning of UPVC waste Pipe conforming to IS :

4985-2000 class III including all moulding fittings conforming to IS : 7834 (Part-1 -

6 M.R. Part -7) 1987 such as tees, bends, reducers, coupling, adopters etc. solvent welded

joint as per manufacturer recommendation including cutting and making good the

walls, floors, R.C.C. work etc. (For fixtures waste).

a) 40 mm (OD) Meter 25 267 6,675

b) 50 mm (OD) Meter 20 836 16,720

c) 63 mm (OD) Meter 20 658 13,160

Providing and fixing UPVC floor drain including all fitting and accessories fixed in

cement mortar complete in all respect.

a) 110 mm OD x 63 mm OD Nos. 2 424 848

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Providing, fixing, testing and commissioning of UPVC rain water pipes (IS : 4985-

1983 class-III ) including injection moulded fittings (heavy duty) (plain or door)

e.g. bends, junction, cowls, tees, offsets, access pieces etc. Clamps/Supports

jointing with rubber ring/solvent cement joints including cutting chase or holes in

walls and floors and making good as required at Site [For Balcony Drain + Terrace

Rain Water Downtake Pipe]. -

a) 110 OD Meter 65 1278 83,070

Providing, fixing to the inlet mouth of rain water pipe PVC grating / Jali of following

size including all fitting and accessories including civil work.

a) 200 mm x 200 mm size (for Terrace Rain Water) Nos. 4 355 1,420

Providing & fixing 1 mm thick stainless steel grating with rim of approved design

including setting in floor with cement mortar. (For Floor Drain)

a) 125 mm dia Nos. 4 409 1,636

Providing & fixing rain water `Khurras' size 45 x45 cm with average minimum

thickness of 5 cm cement concrete 1:2:4 (1 Cement: 2 coarse: 4 graded stone

aggregate of 20 mm nominal size) over PVC sheet 1 m x1m x400 micron, finished

with 12 mm cement plaster 1:3 (1 Cement: 3 coarse sand) and a coat of neat

cement, rounding the edges and making and finishing the outlet complete.

TOTAL OF SUB HEAD - 2 : SOIL, WASTE AND RAIN WATER PIPES - 3,77,137

C SUB HEAD - 3 : WATER SUPPLY (INTERNAL AND EXTERNAL)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

1 18.7 fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement and testing of joints

complete as per direction of Engineer in Charge.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Internal work - Exposed on wall

a) 18.7.2 20 mm nominal outer dia Pipes Meter 25 335.00 8,375

b) 18.7.3 25 mm nominal outer dia Pipes Meter 25 401.55 10,039

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and the cost of cutting chases

and making good the same including testing of joints complete as per direction of

Engineer in Charge. -

Concealed work, including cutting chases and making good the walls etc.

a) 18.8.1 15 mm nominal outer dia Pipes Meter 65 497.80 32,357

b) 18.8.2 20 mm nominal outer dia Pipes Meter 35 537.60 18,816

c) 18.8.3 25 mm nominal outer dia Pipes Meter 20 627.25 12,545

d) 18.8.4 32 mm nominal outer dia Pipes Meter 15 739.30 11,090

Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and

making good the walls etc. -

Internal work - Exposed on wall -

a) 18.10.4 32 mm dia, nominal bore Meter 15 667.00 10,005

Providing and fixing forged brass nickel plated lever operated ball valve of full flow

4 18.18 with forged brass hard chrome plated ball with min. working pressure of 15 Kg/cm2.

Lever should be anti rust coating, complete in all respects. -

a) 18.18.1 15 mm dia Nos. 12 348.85 4,186

b) 18.18.2 20 mm dia Nos. 8 397.45 3,180

Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure

not less than 15 Kg/Sq.cm. -

a) 15 mm nominal bore Nos. 1 736 736

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

DSR-Civil- Providing and placing on terrace polyethylene water storage tank, IS : 12701

2023 marked, with cover and suitable locking arrangement and making necessary holes

Item for inlet, outlet and overflow pipes but without fittings and the base support for

No.18.48 tank. Per Liter 1000 8.36 8,360

TOTAL OF SUB HEAD - 3 : WATER SUPPLY (INTERNAL AND EXTERNAL) 1,18,952 736

D SUB HEAD - 4 : EXTERNAL SEWERAGE AND DRAINAGE SYSTEM

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse

sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III)

: 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1

cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal

1 19.70 size), inside plastering 12 mm

thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat

of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat

of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty)

455x610 mm internal dimensions, total weight of cover and frame to be not less

than 38 kg.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 10 12770.55 1,27,706

Extra for depth for manholes Size 90x80 cm With common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 Meter 1 8825.40 8,825

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Providing orange colour safety foot rest of minimum 6 mm thick plastic

encapsulated as per IS: 10910 on 12 mm dia steel bar conforming to IS: 1786

having minimum cross section as 23 mm x 25 mm and over all minimum length 263

mm and width as 165 mm with minimum 112 mm space between protruded legs

having 2 mm tread on top surface by ribbing or chequering besides necessary and

3 19.16 adequate anchoring projections on tail length on 138 mm as per standard drawing

and suitable to with stand the bend test and chemical resistance test as per

specification and having manufacture's permanent identification mark to be visible

even after fixing, including fixing in manholes with 30x20x15cm cement concrete

block 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal

size) complete as per design. Nos. 40 553.70 22,148

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I.

grating brick masonry chamber with water tight C.I. cover with frame of 300 x300

mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be

not less than 2.70 kg as per standard design ::

180 x 150 mm size P type With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 Each 12 2802.15 33,626

Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in

5 19.28 cement mortar 1:4 (1 cement : 4 coarse sand) with precast R.C.C. vertical grating

complete as per standard design :

a) 19.28.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Nos. 7 6889.00 48,223

Making connection of drain or sewer line with existing manhole including breaking

into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement :

2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered

on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a

floating coat of neat cement and making necessary channels for the drain etc.

complete .

a) 19.21.2 For pipes 250 to 300 mm diameter Each 1 922.40 922

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

TOTAL OF SUB HEAD - 4 : EXTERNAL SEWERAGE AND DRAINAGE SYSTEM

E SUB HEAD - 5: FIRE EXTINGUSHER

MR Supply & erection of ISI marked portable fire extinguishers, confirming to IS:15683,

wall mounted type, wall brackets complete in all respect as per standard item with

all accessories, delivery hose & nozzle whereever required, including fixing on walls

as per the directions of Engineer-in-charge.

1.01 MR CO2 gas type. 4.5 kg. capacity with confirming to IS:15222. Nos 6 14366 86,196

1.02 MR ABC dry powder Type 6 kg. capacity with confirming to IS:14609. Nos 6 8210 49,260

TOTAL OF SUB HEAD - 5: FIRE EXTINGUSHER - 1,35,456

F SUB HEAD - 6: LABORATORY GAS PIPELINE (O2,N2,He,Ar & Other)

MR MS Power coated Gas Cylinder Safety Cabinet with safety Glass window for

He,N2,Argon, O2 and One Other

Sheet Thickness : 1.5 mm

Size Approximate : 660 mmX432 mmX2210 mm 1,99,500

MR Single stage Regulator with Single Cylinder Manifold with Purge valve for

purity up to 6 grade gas MOC:SS316L Electro Polished Plated Specially Cleaned

Diaphragm: Hastelloy

Inlet Pressure Range:200 bar Outlet Pressure Range : 1 to 14 bar

With Inlet & Outlet Pressure Gauges, With Pressure relief valve

2 With 10 micron inbuilt filter at inlet & 100 micron filter at outlet No 4 1,20,365

,With 1 numbers of Inlet Shut-Off Diaphragm Valves, With 1 Numbers of Internal

Diaphragm Purge Valves Inlet/Outlet: 1/4" FNPT

Guaranteed leak Rate:1*10-9 mbar l/s Helium (Outboard)

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

MR High Flow Automatic Gas Changeover System For Nitrogen Gas.

Wall Mount –Factory Assembled, Integrated with Helium Leak Test,

Oxy cleaned, Purity 5.5 Grade Gases(99.9995%) Single Stage, MOC= Brass Chrome

Plated, Specially Cleaned,

Inlet Pressure = 230 Bar

Outlet Pressure Range = 10-12 Bar Fixed Diaphragm=Hastelloy, ATEX compliant

adjustment knob,

1. With Inbuilt 10-micron filter at Regulator Inlet,

3 2. and 100-micron Filter at Regulator Outlet, No 1 2,79,965

3. With 2 nos. of Diaphragm Inlet Shut-Off Valves,

4. With Integrated 2nos. Inlet and 2nos. Outlet Pressure Gauge,

5. With 1nos. Integrated Pressure Relief Valve, Inlet & Outlet Port 1 = 1/4"NPT(F)

Guaranteed leak rate of <1x10-9 mbar l/s (He)

Single Stage Regulator

MR SS Corrugated metal hose With SS316 internals

Oxy Cleaned ,OAL:1 meter

With Safety wire along the length MAWP: 340 bar

End Connection: 1/4" FNPT X 1/4" MNPT Testing For Nitrogen, Argon and Zero Air

MR Non Return Valve

MOC:SS316L,

Inlet & Outlet: 1/4" OD,Cracking Pressure: 1PSIG,

Max Working Pressure: 206 bar 55,860

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

MR SS 316 1/4” OD 7 Micron Online Particle Filter.

Filter Element Size -7 Micron

Features – 7 Micron Element Pore Size. Maximum Temperature- 9000F Minimum

Temperature: -200F

Element : cylindrical Type

Element 1,23,690

MR Flame Back Arrestor

MOC : Brass, Pressure : 10 Bar max

The safety device DGN-VA according to EN 730-1, ISO 5175:

• avoids dangerous gas mixtures by a gas non- return valve (NV)

• stops flashback through flame arrestor (FA)

• a temperature-sensitive cut-off valve stops the gas flow when

7 a predetermined temperature is exceeded (TV) No 2 21,280

• a dust filter protects the gas non-return valve against contamination

• every safety device is 100% tested

• all metal components in stainless steel 1.4305 /

spring 1.4310

MR SS-316 Inner Electropolish and Outer Clean Tubing

RA Valve : 20 RA.,Thickness : 1 mm 4,40,980

MR Point of Use

Point of use High Sensitivity regulators-Single Gauge (Outlet Gauge)

For Purity up to 99.9995%

9 MOC : SS316L, Specially Cleaned, Electro Polished Diaphragm: Hastelloy, Inlet No 10 91,105

Pressure : 50 bar Outlet Pressure : 0.5 to 12 bar

With Outlet Pressure Gauge

With Inlet & Outlet Ports=1/4"NPT Female (GCE) 9,11,050

MR Automatic Gas Pressure Alarm with Digital Gas Cylinder Pressure Reading Panel for

10 He,N2,Argon, O2 and One Other No 6 2,40,065

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

MR Installation charge with Orbital weld and fittings

for above 1,86,865

SUB HEAD - 6 :TOTAL LABORATORY GAS PIPELINE WORK 42,90,000

HVAC WORK

SUB-HEAD 'A' - AIR CONDITIONING EQUIPMENTS HIGH SIDE (VRV/VRF

1.0 AIR COOLDED VARIABLE REFRIGERANT VOLUME/FLOW AIR

CONDITIONING SYSTEM

Supply, Installation, testing and commissioning of air cooled Variable Refrigerant

Volume/Flow modular type air-conditioning system Invertor Controlled with step

less modulation complete with indoor and outdoor units, individual remote controller

and centralized controller, interconnected refrigerant piping ,full charge of

refrigerant gas & oil, control cabling etc.as per detail given in specifications and

having following items: Refrigerant to be used shall be - R - 410 A.

1.1 OUTDOOR UNIT

Supply, Installation, testing and commissioning of Both Cooling & Heating Modular

type outdoor units suitable to operate at 415 ± 10 % volt, 50 Hz, 3 phase AC

supply and suitable for cooling & Heating application by using 100 % inverter driven

capacity control compressors (Hermetically sealed scroll type) with stepless

modulation complete with special acryl precoated heat exchanger, microprocessor

based Controller, top discharge type condensing unit(s), low noise condenser fan ,

auto check function for connection error in display panel, auto address setting as

per specifications. Complete Set (Indoor and Outdoor) of equipment testing shall be

done in the presence of client representative at AHRI Conditions without any extra

cost. The units shall be complete with necessary mounting frames and capacity as

mentioned below and as per specification.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

The compressor should be of same manufacturer as of outdoor units. The unit shall

have auto phase corrector so that unit can work in case of phase reversal and

accumulator should be present in outdoor units to prevent liquid backflow in

compressor. For better energy efficeincy and power saving the COP of ODU should

be minimum 3.8 at AHRI conditions. The Unit shall be equipped with an oil recovery

system to ensure stable operation with long refrigeration piping lengths. The system

must be provided with oil balancing circuit to avoid poor lubrication.

Outdoor Unit Shall operate between -50c to 500c for Cooling Mode and -250c to 150c

for Heating mode.

Energy efficiency ratio (EER) Shall be not less than 5.5 at 50% part Load Condition

The machine must have a sub cool feature to use coil surface more effectively

through proper circuit/bridge so that it prevents the flushing of refrigerant from long

piping due to this effect thereby achieving energy savings.

The outdoor unit should be fitted with low noise level and should not be more than

65 db (A) at normal operation when measured at a point 1 mtr. In front of the unit

at a height of 1.5 mtr. The outdoor unit shall have feature to change the

evaporative temperature form apprx 6 deg C to 11 Deg C with respect to load for

better comfort and energy efficiency. (VRT-Variable refrigerant temperature

technology). The systems shall have free phase technology & operation shall be

continuous in case of phase reverse in supply electricity.

The cost should include the following :

Nitrogen pressure testing for refrigerant pipe leakages & flushing during installation

& after commissioning between IDU & ODU with flare nuts. Refrigerant gas & oil

charging as per OEM standard.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Necessary corrosive treatment of copper coil of the ODU with Aluminium hydroxide,

25 microns thickness or equivalent coating as per manufacturer standard to protect

from corrosion, sulphur and other chemical contaminants present in the air. The

coating should be done in the presence of OEM representative. The coating shall be

carried-out by the authorized applicator of coating manufacturer.

Note : The ODU provided with cowl duct for exhaust air should have minimum 5

mm ESP. GI wire mesh (minimum 16 SWG thickness) type bird screen with framing

at the Mouth of exhaust air Cowl duct of Outdoor Units, where ever required.

ODU Units Mounted on MS Frame/Masonry Pedestal with required anti-vibration

mounting.

a) 14 HP (1x14 HP) Nos. 1 ₹ 2,29,810.00 2,29,810

b) 36 HP (2x18 HP) Nos. 1 ₹ 5,90,940.00 5,90,940

1.2 Indoor VRV/VRF Units

Supply, Installation, testing & commissioning of metallic body indoor (Hi-Wall,

Cassette & Ducted) Units of following minimum capacity suitable to operate at

230+/-10% volt, 50 HZ, 1 phase power supply and having multispeed motor,

blower, coil section with DX coil, outer cabinet, drain pan, drain pump, drain water

lift-up mechanism, insulation, pipe connections, fittings & required cable to connect

indoor unit to MCB etc. complete in all respect and as per specification.

Indoor Units powder coated MS Hanging arrangement/wall Brackets with required

anti-vibration mounting.

1.2.1 CEILING MOUNTED 4-WAY/1-WAY CASSETTE UNITS

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Supply, installation, testing and commissioning of following minimum

capacity 1-Way/4-way flow VRV/VRF Cassette Type Indoor ceiling mounted

unit equipped with synthetic washable media pre-filter, fan section with low noise

fan/dynamically balanced blower, multispeed motor, coil section with DX Copper

DSR coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary

VRV/VR supports, vibration isolation, cord less remote control etc., suitable for

F -2019 operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required.

The unit shall have automatic force shut down provision in case of fire on receiving

signal from BMS System. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB temperature.

Indoor Units powder coated MS Hanging arrangement/wall Brackets/Spring

Isolators with required anti-vibration mounting.

1.2.1 4-Way Cassette Unit

a) 2.3 1.6 TR (525 CFM) Nos. 1 ₹ 29,488.00 29,488

1.2.1 1-Way Cassette Units

b) NSR-1 1.6 TR (525 CFM) Nos. 1 ₹ 71,900.00 71,900

1.2.3 CEILING SUSPENDED DUCTED TYPE UNITS

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Supply, installation, testing and commissioning of following minimum

capacity and external static pressure VRF/VRV ceiling mounted

ductable type Indoor unit equipped with washable synthetic media

pre-filter, fan section with low noise fan/dynamically balanced

blower, multispeed motor, coil section with DX copper coil, electronic

DSR expansion valve, corded remote control, outer cabinet, vibration isolators, drain

VRV/VR pump, drain pan, fire retardant non-porous double layer flexible connection,

F -2019 other necessary supports etc., suitable for operation on single phase AC supply 230

V± 10%, 50 Hz complete as required. The unit shall have automatic force

shut down provision in case of fire on receiving signal from BMS System.

The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB

and 19 Degree C WB temperature.

Indoor Units powder coated MS Hanging arrangement/wall Brackets/Spring

Isolators with required anti-vibration mounting and Fire Rated Flexible Connection.

High Static Ductable units (minimum 150 pascal external static pressure)

a NSR-2 4.5 TR (1800 CFM) Nos. 2 ₹ 80,117.00 1,60,234

b 4.18 6.5 TR (2400 CFM) Nos. 2 ₹ 87,281.00 1,74,562

1.3 CEILING SUSPENDED TREATED FRESH AIR UNITS

Supplying, installing, testing and commissioning of Ceiling Suspended Treated

Fresh air Units each complete with coil, filter, etc. Air conditioners with

evaporating unit comprising of cooling coil, blower with motor and 220 volt, 1

phase, 50 Hz, AC supply all as per specifications. The rate will also include entire

drain pipes and nothing extra shall be payable.

a) NSR-3 4.5 TR (600CFM) Nos. 1 ₹ 85,595.00 85,595

1.4 Refrigerant Joints and Headers

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

NSR-4 Supply, Installation, Testing and Commissioning of copper Y-Joints sets, distributer

and headers, suitable for various sizes of gas and liquid line of VRF System Nos. 8 ₹ 7,532.00 60,256

complete as required for the above system.

1.5 Corded/Cordless Remote Controller

NSR-5 Supply, Installation, testing and commissioning of self diagnostic type

Corded/Cordless remote controllers for operation of indoor units.

1.6 Central Remote Controller

Supply, Installation, testing & commissioning of Main intelligent central

controller with Scheduled Timer system Touch screen/Gate Way Type suitable

for groups of indoor units to operate, monitor, on/off, cyclic operation setting,

temperature setting etc. The controller shall be able to control up to minimum nos.

of indoor units with zoning option as mentioned below. The controller shall have

wide screen user friendly colour LCD Touch screen display and can be wired by a

non-polar transmission cable The CRC shall be provided with suitable size metallic

box with lock arrangement. The controller shall be integrated to BMS system thru

software for monitoring & controlling of all above parameters including start/ stop of

each indoor / outdoor unit. All necessary interface cards / units should be supplied

as a part of the system to integrate to the BMS Software.

a) NSR-6 Maximum 64 Nos of Indoor Units Nos. 1 ₹ 1,57,495.00 1,57,495

2 AIR PURIFICATION SYSTEM

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Supply, installation, testing and commissioning of duct mounted Air Purification

System with advance oxidation plasma cell (AOP) comprising of UVC lamp 254 NM

with nanoX coating metallic compound of five metals targeted on Alumninum matrix

cell duly enclosed by a poly quartz casing tube, with the capability to produce

ionized Hydroxyl oxidizers with in-built plasmoX to generate ion generator pins (+-

ions 10^6) along with ultrasonic radio frequency waves for pest repellancy. The UV-

C lamp will be a low-pressure mercury type and of such intensity as to provide

minimum performance as listed below. The UV-C lamp will produce only Germicidal

UV (by definition this means 99.99% UV-C energy). The airpurifier will have built in

LED indication system stating the operation of the 3 technologies the UV lamp,

ionizer and pest repellant. The AOP cell shal be capable of removing Particulate

matter, Gasous Contamination as well as Microbial Contamination. The power /

control cabling between the Pentagon units and the power source / controls shall be

included in the cost .

The wattage of the lamp shall not be less than 13 watts upto and length not less

than 212 MM upto 2000 CFM, 21 watts upto and length not less than 436 MM upto

2000-6500 CFM, 36 watts upto and length not less than 436 MM upto 6501-18000

CFM and a minimum of 48 watts upto 28000 CFM or combination based on the

application area. The system shall be capable of reducing microbial bacteria, virus

and spores , VoC’, odors and particulates matter. The equipment shall have to CE,

ISO 13485, ROHS, TUV, FICCI, GreenPro with 2014/35/EU Low Voltage Directive

along with FDA compliance certifications. The AOP cell shall a microbiological

testing report against Bacteriophage (MS-2 FDA) surrogate SARS Cov-2 with a

minimum efficiency of 99 percent along with a Virology report from ICMR approved

lab with an minimum efficiency of 99 percent against SARS COV2 within 45

minutes. The technology shall be tested by ICMR/ IIT on human Alveolar Basal

Epithelial Cells stating that there is no change in the structure and prove that it is

absoluely safe for humans.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

The air purfication AOP does not produces ozone, the test certificate from an

International Lab shall be produced. The specific certifications shall be submitted

along with the technical submital. The failure to submit the certifications along with

by considering a load factor calculation for each specific area where the equipment

is to be installed. The Cells Should be complete with Transformers, control cabling

and Plug Top & necessary power cable. Vendor to comply all Tender Specifications.

a) NSR-7 Cassette Type (4-Way) Nos. 3 ₹ 34,238.09 1,02,714

b) NSR-8 Ductable Unit(TFA) Nos. 5 ₹ 43,824.75 2,19,124

Notes: -

a) The vendor may offer the outdoor units as per availability from the manufacturer,

however keeping the tonnage same as per BOQ subject to approval by

Consultant/Client.

b) The indoor units capacity can be also as per availability from the manufacturer but

keeping the minimum capacity as required in BOQ subject to approval by

Consultant/Client.

Total Of AC Equipment High Side 10,24,800 9,20,862

SUB-HEAD 'C'- VENTILATIONS EQUIPMENTS

3.0 INLINE FAN (Ceiling suspended)

Supply, installation, testing, commissioning of Single Skin Inline fan with Backward

Curved SISW Fan, vibration isolators, speed regulator, GI gravity louvers, Bird

Screen and required cable as per specification and drawing. The Motor shall be

suitable to run on 1 phase/50 hz/ 220 v electrical power Supply including fire

retardant non-porous double layer flexible connection of the following capacity.

Thickness of casing : Upto 1000 CFM - 2mm , above 1000 CFM - 3mm

The louvers & bird screen shall be made of 24G & 16G metallic construction

respectively.

a) NSR-9 600 CFM at 10 mm static pressure Nos. 1 ₹ 28,075.00 28,075

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

4.0 PROPELLER FAN:

4A METALLIC TYPE PROPELLER FAN

Supply, installation, testing and commissioning of wall mounted Propeller type

heavy duty exhaust Fan of metallic construction complete with speed regulator, bird

screen, gravity louvers, vibration isolators, required cable, plug & other accessories

compete as required, suitable for single phase, 240± 10 volts, 50Hz AC. supply of

following capacities:

a) NSR-10 300 mm sweep dia (900 RPM) Nos. 1 ₹ 4,318.00 4,318

Total Of Ventilation Equipment's - 32,393

SUB-HEAD 'D' -REFRIGERANT/DRAIN PIPING & CONTROL WIRING

5.0 TRANSMISSION & CONTROL WIRING

Supplying, installing, testing and commissioning of Shielded control cum

transmission wiring of 2 core x 1.5 sqmm copper FRLSH, XLPE insulated cable in

suitable GI conduits accessories between indoor and outdoor units. Necessary

securing of conduit shall be made by contractor. After completion of work wall and

floor shall be repaired and brought to its original finish. The rate will also include

cost of laying of GI conduit between indoor and outdoor units.

a) NSR-11 2C x 1.5 Sq mm (Shielded-Unarmoured) RM 165 ₹ 199.00 32,835

6.0 REFRIGERANT PIPING

Supply, fixing, testing and commissioning of interconnecting soft/hard drawn

copper refrigerant pipe work of following outer diameter duly insulated with fire

rated class'O' closed cell elastomeric nitrile rubber insulation (19mm/13mm thick)

between indoor & outdoor units. Exposed piping will be protected with 26 G

aluminium sheet cladding as per specifications. All piping should be laid on

Galvanized/Powder Coated tray supported by Galvanized M S Hangers & Clamps

and all external piping shall run in covered cable trays. The rate includes all the

items required to complete the piping work and nothing extra should be payable

except the cable tray.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

Vaccumiazation & Nitrogen pressure testing for leakages & flushing during

installation & after commissioning between IDU & ODU.

Civil Work such as wall hole making , wall chiselling ,refilling of chiselling part with

mortar etc. as per site condition.

Covering of External refrigerant piping insulation shall be done with 26 G aluminium

sheet cladding as per specifications.

Internal Refrigerant piping insulation shall be covered with Aluminium Foil as per

specifications.

a) 5.1 6.4 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

b) 5.2 9.5 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

c) 5.3 12.7 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

d) 5.4 15.9 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

e) 5.5 19.1 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

f) 5.6 22.2 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

g) 5.7 25.4 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

h) 5.8 28.6 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

i) 5.9 31.8 mm outer dia Hard Drawn with Tube Thickness-1.62mm ( Insulation-19 mm )

j) 5.10 34.9 mm outer dia Hard Drawn with Tube Thickness-1.62mm ( Insulation-19 mm )

k) 5.11 38.1 mm outer dia Hard Drawn with Tube Thickness-1.62mm( Insulation-19 mm )

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST

DETAILED BOQ

Name of Project: Design, manufacturing, supply and erection including interior and exterior finishes with LGSF/Pre-fab structure technology at the

first floor of Department of Biotechnology, CIR Lab and Mess in MNNIT Allahabad, Prayagraj (UP)

S.No DSR

Description of items Unit Qty. Rate Amount

DSR NSR

l) 5.12 41.3 mm outer dia Hard Drawn with Tube Thickness-1.62mm( Insulation-19 mm )

7.0 DRAIN PIPING

Providing and fixing of cPVC drain water piping complete with fittings, flexible

connection to IDU, necessary support as per specification and insulated with 6 mm

thick fire rated class'O' closed cell elastomeric nitrile rubber insulation.

a) NSR-12 25 mm dia RM 48 ₹ 240.00 11,520

b) NSR-13 32 mm dia RM 32 ₹ 267.00 8,544

c) NSR-14 40 mm dia RM 15 ₹ 383.00 5,745

d) NSR-15 50 mm dia RM 1 ₹ 452.00 452

TOTAL OF Refrigerant /Drain Piping & Control Cabling 1,40,506 59,096

SUB-HEAD 'E' - AIR DISTRIBUTION WORKS

(DUCTING,INSULATION,DAMPER, GRILLE & DIFFUSER)

8.0 DUCTING FOR AIR CONDITIONING / VENTILATION

8A FACTORY FABRICATED GALVANIZED SHEET METAL DUCTS (GSS)

Supply, installation, testing and commissioning of factory fabricated 120 GSM

Galvanized Steel (GSS) Sheet metal ducts complete with flanges, neoprene

rubber gasket, elbows, Splitter Damper, vanes, hangers & support etc. as required

DSR E&M- as per IS/DW144/SAMACNA standard & confirming to specification. Duct shall be

2022 furnish at site in "L" shape or box shape from factory. The rates shall include all

materials of the duct and labour for suspension and supporting arrangement for

plenums, ducts, complete with fire retardant flexible connection as required and as

per specifications.

Flange joints shall have 6 mm thick Neoprene packing as gasket stuck to the

flanges with adhesive (viz., resins like araldite or equivalent). All the duct shall be

made air tight with the help of sealant. Leak test shall be conducted on the duct

before insulation.

Digitally signed by GOUTAM

KARMAKAR

Date: 2025.09.18 10:48:47 IST