ADDN/ALTN TO SMQS IN KV AREA (PH-III), PROVN OF ALUMINIUM PARTION, ALUMINIUM DOOR, ALUMINIUM SLIDING WINDOW AND ALLIED INFRA AND ADDN/ALTN TO ROOM NO. 17 AT 10 AFH AT AFS HASIMARA

Amount

Takiing down chowkat with shutter (without taking off shutter from the frame) n.exc 1.5 Sqm each, complete all as specified and directed.

Takiing down chowkat with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n.exc 4 Sqm each, complete all as specified and directed.

Taking down shutter of any description exc 1 & n.exc 2 Sqm each, complete all as specified and directed.

Taking down shutter of any description exc 1 & n.exc 2 Sqm each and refixing in same opening, complete all as specified and directed.

S & F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side prelam PVC sheet. Stile and rails feathered at edges for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of both side Prelam PVC sheet. to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable Prelam PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, as per specification & drawing, complete all as specified and directed.

S&F 125 x 60mm size pressed steel door frames of doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

S&F 105 x 60mm size pressed steel door frames of doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F of 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

S & F 35mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc, complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or stainless steel wire staples, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or stainless steel wire staples, complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth not otherwise described and applying two coat of synthetic enamel paint (1st grade quality) over coat pf pink primer, complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint (1st grade quality), complete all as specified and directed.

S&F 25mm thick wooden grain PVC sheet celluka ply for shutters of built in cupboards, almirahs, book cases, toilet boxes, racks and similar work fixed with screws/self tapping screws etc, complete all as specified and directed.

S&F 18mm thick wooden grain PVC sheet celluka ply fixed in shelves, partitions and shelves of built in cupboards, almirahs, book cases, toilet boxes, racks, pelmet and similar work fixed with screws/self tapping screws etc, complete all as specified and directed.

S&F of 8mm dia ball catches with steel and brass body and striking plate including letting in and fixed, complete all as specified and directed.

S&F 75mm aluminium anodised hasp and staple, safety type and fixed with screws, complete all as specified and directed.

S&F 150mm long aluminium handle, cast type, anodised, complete all as specified and directed.

S&F 100mm long aluminium handle, cast type, anodised, complete all as specified and directed.

S&F butt hinges of size 100mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type C-21, complete all as specified and directed.

S&F butt hinges of size 75mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type C-21, complete all as specified and directed.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

S&F 150mm long aluminium anodised, barrel tower bolt of extruded section, complete all as specified and directed.

S&F mild steel flat as in hold fast, wall ties, plain angle, clean for securing purline to wood trusses, conforming to Fe 290 Gde E-165, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

S&F steel windows with side hung shutters (ISI marked), factory fabricated including projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded including making good the opening with necessary putty/plastering/painting required, complete all as specified and directed.

S&F steel windows with side hung shutters (ISI marked), factory fabricated including box type hinges with steel handle and steel peg stay complete without glazing bars, dovetailed or welded including making good the opening with necessary putty/plastering/ painting required, complete all as specified and directed.

S&F steel ventilator with top hung shutter (ISI marked), factory fabricated including hinges, steel peg stay including making good the opening with necessary putty/plastering/painting required, complete all as specified and directed.

M&L for mild steel framed work such as grill, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barrel iron doors, ladders framed balusters, walks railings, frame work of water tanks and similar work conforming to E-165 (Fe-290) including two coats of synthetic enamel paint over one coat of red oxide, complete all as specified and directed.

Dismantling timber scantlings 40 Sqm and over in section, framed work, in any position, complete all as specified and directed.

Demolition of brick work or sone/boulder masonry, built in cement mortar including all quoiins, pillars etc, separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100m and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100m, complete all as specified and directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for including disposal of debris and rubbish to a distance not exceeding 100m, complete all as specified and directed.

M&L for brick work with flyash bricks, old size, straight or curved on plan exc 6 mtr mean radius built in CM (1:6), complete all as specified and directed.

M&L for brick work with flyash bricks, old size, straight or curved on plan, any radius, built in CM (1:4) in half brick thick wall, complete all as specified and directed.

Taking down cement plaster of any description any thickness incl racking out joints hacking for keys scrubbing down with water etc, including disposal of debris and rubbish to a distance not exceeding 100m, complete all as specified and directed.

M&L 15mm thick rendering in CM (1: 6) on fair faces of brick work or concrete surfaces, finished surfaces even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 15mm thick in two coats (10mm under layer + 5mm top layer) on fair faces of brick work or concrete surfaces of wall in CM (1:4), mixed with water proofing compound on top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement, complete all as specified and directed. (Note : WPC shall be measured and paid separately as 'supply only'.)

M&L 5mm thick rendering in CM (1:3) on ceiling surfaces/ chajja etc finished even and smooth without using extra cement, complete all as specified and directed.

M&L 10mm thick rendering on fair faces of brick work or concrete surface in CM (1:3) using water proofing compound @ 3% by weight of cement as in sunken portion, complete all as specified and directed.

M&L 25mm thick PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in sunken portion, complete all as specified and directed.

Cleaning the surfaces of brick/RCC using wire brush, brooming down and washing down with water to remove dust etc. and brushing with neat cement slurry @0.5 kg/sqm with acrylic based polymer modified cementitous composite (like Pidifine 2K) @ 0.50 kg/sqm, complete all as specified and directed.

M&L for PCC (1:5:10) type E-2 (using 40mm graded crushed stone aggregate) as in sunken portion, complete all as specified and as directed.

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification, complete all as directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of old decorated surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds moss and efflorescent salts, trading oil, greasy spots and applying two coats of white wash, complete all as specified and directed.

All as per item No 47.00 here-in- before but on ceiling, soffits of slabs, chajj etc, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

M & L for complete removal of existing treatment of old decorated surface of walls and applying two coats of water based acrylic weather proof exterior emulsion paint of approved colour and shade, complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of water based acrylic weather proof exterior paint of required shade over a coat of exterior emulsion primer, as per manufacturer's instruction, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistance primer, complete all as specified and directed.

M&L for preparation of old plastered wall surfaces and applying one coat of cement base paint, complete all as specified and directed.

M&L for complete removal of existing treatment of old decorated surfaces of wall and applying two coats of oil bound distemper over and including 1.5mm to 2mm thick wall care putty for smooth finished surface, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over and including a coat of 1.5mm to 2mm thick wall care putty, complete all as specified and directed.

M&L for preparing surface of new plastered or unplastered wall surfaces and applying two coats of oil bound distemper over a coat of chalk whitening primer, complete all as specified and directed.

S&F mild streel 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

S&F 3mm thick plain sheet glass, ordinary quality and glazing with oil putty/wooden beads in square n.exc 0.5 sqm. in each pane, complete all as specified and directed.

M&L for 3mm thick figured glass, pin head type and glazing with oil putty/wooden beads in squares n exc 0.5 sqm in each pane, complete all as specified and directed.

Dismantling of floor, hearth or wall tiles including cement mortar bedding (but not backing), removing serviceable tiles or stone and remvoing rubbish off the premises, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match the surfaces over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

All as per item No 62.00 here-in before but as in skirting/dado over and including rendering 10mm thick in CM (1:4) as backing coat to receive wall tiles, complete as specified and directed.

M&L glazed ceramic coloured tiles in vertical surface 350 x 250 x 7mm/450 x 300x 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in CM (1:4) as backing coat to receive wall tiles, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar, complete all as specified and directed

M&L for 14-16mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over and including 15mm thick rendering in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm thick screed bed of cement mortar (1:6), complete all as specified and directed.

M&L for machine cut kota stone slab flooring and shelves, 20-25mm thick, laid over and including cement screed bed/bedding layer of 20mm thick, in CM (1:6), laid and jointed with grey cement slurry, mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

M&L for machine cut kota stone slab 20-25mm thick on vertical surfaces of wall as in riser of steps, skirting, dado and pillar, laid over and including 10mm thick rendering in CM (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded crushed stone aggregrate) as in benching/coping, kerbs or mud stops etc., rounded or chamfered on edges, complete all as specified and directed.

S&F false ceiling with powder coated exposed Gl grid suspension system (E-Grid T- 2430 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c) consisting of Main Runner 3600mm long, Cross Tee 1200rnm/600rmm long and Wall Angie. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c The Main Runners to be placed @ 1200mm, The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600mm to form a modular grid of 1200mm x 600mm. Additional Cross Tees of 600mm shall be placed perpendicular to the Cross Tee 1200mn iong to finally form a grid of 600mm x 600mm. Grid of module size 600mm x 600mm shall be supported by 3 to 4mm dia GI wire from purlins/soffit including providing 4mm thick Fiber Cement Designer Board, should be placed in the grid module to form a false ceiling including dismantling of old unserviceable false ceiling, complete all as specified and directed

Roughening surfaces of old concrete roof by picking, sweeping clean and washing down with water using wire brush, brooming down and applying the following treatment all as directed in order of precedence as stated: (a) Brushing neat cement slury with 3.0 kg of cement per Sqm. (b) 15mm thick screed bed or bedding layer in CM (1:4) mixed with water proofing compound as permanufacturer instruction on existing roof surface true to level. (c) Applying one coat of bituminous primer @ 0.40 Ltr/Sqm confirming to IS-3384. (d) Supply and laying 3mm thick APP based polymeric membrane of approved manufactured with weight not less than 3.50 Kgs per Sqm reinforced with non-woven polyester fabric weighing not less than 160gms per Sqm having softening point not less than 15°C, having tensile strength of 650 N/Sqcm and 350 N/Sqcm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180 N by torch application. Polymeric membrane shall be taken to a height of 30cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (e) Applying one coat of aluminium paint @ 0.11 Kg/Sgm over APP membrane surface. Note:- (i) Laying APP based polymeric membrane shall be done torch on method as per manufactures instructions. (ii) A minimum overlap of 100mm and 75mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instruction. (iii) APP based polymeric membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given in IS 16540-2017/1S 16532 2017. (iv) Contractor shall produce necessary test certificate of the manufacturer to the Engr-in-Charge before incorporation in the work. (v) Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work. (vi) The work shall be executed through authorised applicators of original manufacturer only. (viI) WPC shall be measured and paid separately as supply only.

M&L for preparation of old painted steel or iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint (1st grade quality), complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer, complete all as specified and directed.

M & L for obliterating old writing of any description, not exceeding 0.1 Sqm, with synthetic enamel paint to match the existing work, complete all as specified and directed.

M&L for writing letters or figures (Block. Roman, Italic or Indian) n. exc. 30cm high, complete all as specified and directed.

Taking down 15mm bore steel water tubing and connection from wall /ceiling surfaces including cleaning for re-fixing or removing from site of work, complete all as specified and directed.

Re-fixing old steel water tubing and connection, 15mm bore, in new or old position (wall, ceiling, floors, etc.) with new fittings, complete all as specified and directed. (Note : Serviceable steel tube obtained from taking down shall be re-used)

S&F steel water tubing and connection, medium grade, 15mm bore with all fitting fixed concealed to wall or in ceiling complete and making good surfaces with CM (1:3), complete all as specified and directed.

Taking down 20mm bore steel water tubing and connection from wall /ceiling surfaces including cleaning for re-fixing or removing from site of work, complete all as specified and directed.

S&F steel water tubing and connection, medium grade, 20mm bore with all fitting, fixed to wall or in ceiling with and including 'J' hook, complete all as specified and directed.

Re-fixing old steel water tubing and connection, 20mm bore, in new or old position (wall, ceiling, floors, etc.) with new fittings, complete all as specified and directed. (Note : Serviceable steel tube obtained from taking down shall be re-used)

S&F in repair 15mm bore, fancy type, chromium plated, stop valves, concealed type, with long shank and cup, cast copper alloy screwed down high pressure screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair 15mm bore angular stop cock, chromium plated, screwed down, high presure with crutch or butterfly handle screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair vitreous china squatting pan ,"Orissa pattern" white, size 580 x 440mm with integral foot rest, 'P' or 'S' trap, including connection to trap, and to flushing pipe, CI anti -syphonage pipe, complete all as specified and directed.

S&F vitreous china wash hand basin white flat back of size 550 x 400mm including PVC waste pipe 32mm dia, waste coupling including cutting for and pinning in ends of brackets etc including dismantling the existing basin, complete all as specified and directed.

S & F vitreous china wash down water closet pan (pedestal pattern), white (EWC) including plastic seat of same colour of WC and cover and mild steel chromium plated hinginh device, complete all as specified and directed

S&F toilet paper holder, of stainless steel fixed to wall with CP brass screws, complete all as specified and directed.

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks, (made of 100% virgin and food grade plastic), triple layered, (cylindrical vertical with closed top) ISI marked, confirming to IS 12701-1996, hoisted and fixed in position all as specified in SSR Part I (1000 ltr capacity) including 20mm Nipple suitable for HDPE water tank and 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed to 20mm bore pipe inculding dismantling of old unserviceable water tank of any capacity, complete all as specified and directed.

S & F in repair 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends, complete all as specified and directed.

S&F in repair CP pillar tap, 15mm bore, capstan head, screwed down high pressure with or without lettered “hot’ or “ cold” with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F 10 Liters capacity, low level flusing cistern, PVC, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia including brackets and connections to pipe, complete all as specified and directed.

S&F in repairs 15mm bore bib taps, cast copper alloy, chromium plated, fancy type, screwed down, screwed for iron pipe or for brass ferrule, compelete all as specified and directed.

S&F in repair PTMT towel ring fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight - 90 gms), complete all as specified and directed

S&F in repair 15mm bore bib tap standard of PTMT, any colour, high pressure, screwed for iron pipe & fixed (minimum weight - 90 gms), complete all as specified and directed.

Demolition of reinforced cement concrete(reinforcement cut as required to facilate demolition) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L for RCC (1:2:4) (nominal mix) type B1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams, lintels and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. Note : Reinforcement shall be measured and paid seperately.

M&L for RCC (1:2:4) (nominal mix) type B1 (using 20mm graded crushed stone aggregate) as in foundations, foolings foundation beams plinth beams etc, complete all as specified and directed. (Note : Reinforcement shall be measured and paid seperately.)

M&L for RCC (1:2:4) (nominal mix) type B0 (using 12.5mm graded stone agregate) as in beams cantilivers lintel over 1.5m span etc, complete all as specified and directed. (Note : Reinforcement shall be measured and paid seperately.)

Use and waste of form work to sides of concrete foundations, footings, bases of columns, plinth beams and similar works, rough finished surfaces of concrete, complete all as specified and directed.

Use and waste of form work to sides and soffits of floor or roof beams and lintels, contilevers, shelves including supports etc, rough finished surfaces of concrete, complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping), rough finished surfaces of concrete, complete all as specified and directed.

S & F mild steel TMT bars 10mm dia (not lass than Grade Fe-500D), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia., or securing with clips, complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8mm dia and over (not less than Fe 500D), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (n. exc. 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and directed.

S&F in repair sinks with drainage board, made of stainless steel 1mm thick (SS-304), ISI marked, with plugs and wastes including in cement mortar onto dwart wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including waste pipe & coupling 32mm size, complete all as specified and directed.

S&F in repair brass chromium plated towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats, complete all as specified and directed

S&F in repair swivel shower rose, 125mm size, brass, chromium plated, with long head arm for fixing with 15mm bore pipe, complete all as specified and directed.

S&F in repair stainless steel plate rack of size 786mm x 610mm x 254mm (min) made out of 0.65mm stainless steel (SS-204) weight not less than 6 kg fixed with brass screw, complete all as specified and directed.

S&F in repair 25mm dia curtain rod mild steel, chromium plated, decorative type bracket and other accessories for fixing, complete all as specified and directed.

Demolition and breaking of internal dia of pipe 100mm bore / 75mm bore pipes of Salt glazed ware, PVC, AC or Reinforced concrete set in cement mortar, complete all as specified and directed.

Fixing only 110mm bore PVC SWR pipe, in any length with rubber ring joint, fixed to wall with and including clamps, complete all as specified and directed. (Note : Serviceable pipes obtained from item No. 103.00 shall be re-used).

S & F 110mm dia, PVC rain water pipes, single socketed, in any length with sealant rubber ring joints including necessary MS flat iron clamps, (size 40 x 4mm) fixed to walls, complete all as specified and directed.

S & F 75mm dia, PVC rain water pipes, single socketed, in any length with sealant rubber ring joints including necessary MS flat Iron clamps of size (40 x 4mm) fixed to walls, complete all as specified and directed.

S&F 110mm bore, PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction, single, (single T) equal or unequal, complete all as specified and directed.

S&F 75mm bore, PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction, single, (single T) equal or unequal, complete all as specified and directed.

S&F in repair PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm bore, complete all as specified and directed.

M&L 125/110mm size PVC (SWR) gully trap, setting and jointing with solvent cement, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting any gauge thickness including nainital or similar pattern roof covering, complete all as specifed and directed.

S&F pre painted galvalume aluminium zinc coating, GI based corrugated steel sheet 0.50mm thick, of any colour, having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws, complete all as specified and directed.

All as per item No.123.00 here-in-before but except sheets, complete all as specified and directed. Note : Sheet obtained from item No 122.00 here-in-before shall be re-used.

S&F pre painted galvalume aluminium zinc coating, GI based plain steel sheet 0.50mm thick, of any colour, having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S & F MS steel work in tubular trusses and tubular posts including special shaped washers etc., complete using ERW or induction butt welded tubes conforming to I.S.I 1161-1998 Grade St-240 with one coat of zinc chrom primer, complete all as specified and directed.

S&F anodised aluminium frame, powder coated (minimum thickness of powder coating 50 micron) for doors, windows, ventilators, partitions etc with one or more rebates including joining cleat for fixing etc, complete all as specified and directed.

S&F anodised aluminium door shutters, powder coatedg (thickness or powder coating not less than 50 micron)aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc, complete all as specified and directed.

S&F plain sheet glass 4.8mm thick, of any colour and glazing with and including anodised aluminium snap beading or rubber / neopren bead, fixed in aluminum frame either in window/ventilator or door frame, complete all as specified and directed.

S&F for 4 to 5mm thick ACP sheet in panels of aluminium partition, aluminium door exc. 0.5 Sqm in each pane with rubber beading, complete all as specified and directed.

S&F 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and as directed.

S&F 200mm long aluminium anodised, barrel tower bolt of extruded section, complete all as specified and directed.

M & L for PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete, complete all as specified and directed.

M &L PCC (1:3: 6) type C-1 (using 20mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, hold fast blocks, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for sand filling under floors or in foundations or below paver block etc. including watering and consolidation, complete all as specified and directed. (Note : Consolidation thickness shall be measured for payment.)

M&L for hardcore of gauge not exceeding 63mm of broken stone, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and directed.

M & L for 100mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in sub bases, floors and pavings, sub floors etc, complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in sub bases, floors and pavings, etc, complete all as specified and directed.

S&F framed brackets of angles or tees, web and flangs cut to shape, drilled and counter sunk for screw including bending and welding angles as necessary gusset plates, riveting etc. n. exc. 10 kg each brackets conforming to Fe.290, Gde-E-165, complete all as specified and directed.

M&L for 40mm thick damp proof course to horizontal surfaces in cement concrete (1:2:4), type B-0 including necessary formwork and applying polythene film, 50 micron thick, laid over and including a coat of bitumen primer, @ 0.40 to 0.50 kg per Sqm, complete all as specified and directed.

M&L for 150mm bore reinforced concrete pipes, class NP2, laid and jointed complete with collars, complete all as specified and directed.

M&L for PCC (1:3:6) type C-2, (using 40mm graded crushed stone aggregate) as in concrete bed to drain pipes laid in trenches including packing under and haunching against the sides of pipes aftaer they are laid and tested in for 150mm bore pipe, complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in PCC (1:2:4) type B1, smooth finished and reforming benching as required for 150mm bore pipe, complete all as specified and directed.

Taking down carefully copper/aluminium point wiring complete (light, fan, plug point & power complete alongwith fittings (switches, ceiling roses, tube light fittings, bulk head fitting, regulator, sockets main switches, DB removing materials to store & making good of disturb surfaces of wall/floors etc, complete all as specified and directed.

All as per item No 147.00 here-in before but for 3 pin 5 Amp socket point on same board, complete all as specified and directed.

All as per item No 147.00 here-in before but for 3 pin 5 Amp socket point on independent board, complete all as specified and directed.

All as per item No 147.00 here-in before but 2 way point wiring with cable size1.5 Sqmm, complete all as specified and directed.

All as per ser item No. 147.00 here-in before but for one bell/buzzer point controlled by one push button on the same board with other switches or independent, complete all as specified and directed.

All as per item No 147.00 here-in before but with 4.0 Sqmm PVC insulated unsheathed multi stranded cable FRLSH type for one 15 Amp 3 pin socket outlet point including PVC insulated 4.0 Sqmm FRLSH type copper multi stranded conductor as earth wire including steel box of required for modular switches/sockets for 3 pin socket outlet point, 15 Amp on independent board and industrial socket for geyser, complete all as specified and directed.

S&F switch, modular type, single pole, one way, 6 Amp, one module, complete all as specified and directed.

S&F switch, modular type, single pole, one way, 15/16 Amps, one module, complete all as specified and directed.

S&F socket outlet, modular type, multipurpose, having provision for 2/3 pin, 5/6 Amp, combined, two module, complete all as specified and directed.

S&F socket outlet, modular type, multipurpose having provision for 3 pin, 15/16 Amp and 3 pin 5/6 Amp, combined, two module, complete all as specified and directed.

S&F bell push, modular type, single pole, 5/6 Amp, one module, complete all as specified and directed.

S&F switch modular type, single pole, 2 way, 6 Amp, one module, complete all as specified and directed.

S&F in repair of bell, ding dong type AC, 230 volts, single phase complete all as specified and directed.

S&F decorative modular cover plate with frame, 2 module, white, completes all as specified and directed.

S&F decorative modular cover plate with frame, 3 module, white, completes all as specified and directed.

S&F decorative modular cover plate with frame, 4 module, white, completes all as specified and directed.

S&F decorative modular cover plate with frame, 9/10 module, white, completes all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including electronic modular type regulator (2 module), including taking down of unserviceable ceiling fan and deposited to AGE E/M store yard, completes all as specified and directed.

S&F MS box (meter box) of size 900 x 300 x 1000mm (double door) 2.0mm thickness, dust proof with front opening hinged door both side, made out of 2mm thick MS sheet cubical type with powder coated painting for mounting of, electric meter etc inside the box fixed in wall by necessary cutting of wall of suitable size in concealed and making good the surface, by applying cement work, brick work and matching colour (Oil bond distemper) etc including dismantling of MS box, electric meters and fixing the new electric meters in new box carefully including necessary electric connection by suitable size of copper conductor cable of suitable length and testing, complete all as specified and directed. Note : (a) Any plastering work involved while taking out old existing meter and refixing the new meter box is deem to be included in this rate. (b) PVC flexible conduit required within the meter boxes is deem to be included in this item rates.

S&F exhaust fan, steel body AC, single phase, 230V of size 300mm sweep with, blades, and frame and louvers including cutting wall for fixing exahaust fan and making good the opening in CM (1:3) or PCC (1:2:4) type B1 as required at site, completes all as specified and directed.

S&F ceiling rose of size 65 x 50mm surface bakelite 240 Volts, three terminal, complete all as specified and directed.

S&F in replacement decorative, wall mounting, brushed nickel finish fixture with acrylic diffuser suitable for 9 W/10 W LED lamp in each lantern B22 base fittings, complete all as specified and directed.

S&F LED lamp 9 Watt / 10 Watt, B-22 base, complete all as specified and directed.

S&F angular lamp holder, insulated body, suitable for B-22 base including one LED lamp 9 Watt, B-22 base, complete all as specified and directed.

S&F in repair LED lights fitting 1 x 20 W, 220V, AC , box type with driver, LED lighting fixture with extruded aluminium channel, including LED tube light connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F in repair LED light fitting, mirror type with high output diffuser 2 feet, 10 watt 220 V, AC, decorative type with driver, LED tube light of 10 watt connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, completes all as specified and directed.

S&F electric water heater, stoarage type,vartical mounted rust proof ABS outer body with high quality steel inner tank and heating element upto 1.5/2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc. including PVC connection pipe for hot/cold water to existing water lines, necessary fixing arrangement by using 50 x 5mm MS plate/in built fixing arrangement as per OEM and writing MES No., complete all as specified and as directed.

S&F MCB distribution board (DB) TPN with sheet metal encloser, double door, IP 43 protection, 240 volts, 04 way, with 100 Amps rated copper busbar for each phase (as per OEM) IP 43 protection, neutral link for fixing MCBs/Isolators including taking down old unserviceable MCB DB of any description, completes all as specified and directed.

S&F MCB distribution board (DB), SPN with sheet metal encloser, double door, IP 43 protection, 240 volts, 12 way, with 100 Amps rated copper busbar (as per OEM) IP 43 protection, neutral link for fixing MCBs/Isolators including taking down old unserviceable MCB DB of any description, completes all as specified and directed.

S&F MCB SP 6 to 32 Amps, 240V, 10 KA, 'C' curve, including connection and testing, completes all as specified and directed.

S&F MCB SPN 6 to 32 Amps, 10 KA, 'C' curve, including connection and testing, complete all as specified and directed.

S&F MCB 4 pole, 63 Amps, 10 KA, 'C' curve, including connection and testing, complete all as specified and directed.

S&F power unit suitable for load max up to 3.5 KW including sockets 25 Amps, and six module box for mounting of power unit and power socket, complete as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground vertically to a depth not less than 2.25 meter below ground level with top edge of earth plate at a depth not less than 1.5 meter below ground level, earth plate surrounded by 15cm thick packed layer of charcoal dust and common salt, connected to galvanized earth lead wire 4mm thick dia by means of bolts, nuts and washers of galvanized iron or steel and thimbles and other end of the earth wire connected to earthing test point/equipment and protected by galvanized iron pipe light grade 20mm bore, up to earthing test point/equipment fixed with required number of mild steel clamp made out of 25mm x 3mm flat iron and perforated water pipe 20mm dia. GI medium grade of length 2.25 meter and top with socket & plug and bottom connected to earth plate by slit and two bolts/nuts/washers, PCC chamber in PCC (1:2:4) type B-1 and 40mm thick pre-cast RCC (1:2:4) type B-0 cover reinforcement with 40mm x 40mm x 6mm MS angle iron frame of size 25mm x 25mm, excavation & earth work complete all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009, complete all as specified and directed.

S&F LED building security light fitting 35 Watt made up of pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07, complete pre-wired and connecting up with suitable twin core flexible copper wire including provision of necessary GI pipe as bracket, medium grade, 25mm/ 40mm bore pipe (as per the model of light fittings) upto 1.5 Mtr length, bend to shape with necessary clamps made out of mild steel, nuts and bolts etc. including two coats of synthetic enamel paint over a coat of red oxide primer on exposed steel surfaces foe fixing the fitting to bldg etc , complete all as specified and directed.

Taking down single phase electric energy meter any type and refixing, after repair work complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm 4 core including taking out old unserviceable UG cable of any type and size, complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide and not exc 1.5 metre in depth for foundation or cable trenches, shafts, wells cesspits, manholes, pier holes etc. n. exc. 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Removing of excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point in any type of soil, complete all as specified and directed.

Returning filling in incl spreading, leveling watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed.

Supply and laying double walled corrugated (DWC) HDPE duct pipe of 40mm dia (outer) conforming to IS, approved colour complete with fittings for cable protection, complete all as specified and directed.

Note: An amount of Rs.42,406.00 on account of Credit Schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

SHRI PARTHA DUTTA (BID ID -3521517)

BHARAT ELECTRIC (BID ID -3519015)

M/S BISHAL ENTERPRISES (BID ID -3521826)

M/S P K AGARWALA (BID ID -3521710)

M/S ROY ENTERPRISE (BID ID -3519036)

M/S RATHIN ENTERPRISES (BID ID -3521528)

M/S. NARENDRA KUMAR GARG (BID ID -3521525)