ADDITION / ALTERATION AND SPECIAL REPAIRS TO COMPOUND WALL AND DRAINAGE SYSTEM NEAR BLDG NO P-1 AT NAVY PARK AND ADDN/ ALTN AND SPECIAL REPAIRS TO SECURITY WALL NEAR BLDG NO T-4 (PHOENIX VIEW) 408 MC/MF DET UNDER GE HADDO, PORT BLAIR

Amount

Excavation in trenches n. exc 1.5m wide and n. exc 1.5m in depth in hard/dense soil for foundation, etc or for shear beam, shafts, wells, cesspits, manholes, pierholes, etc n. exc 10 Sqm on plan and n. exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed

Demolition of cement concrete (Unreinforced) in ground floors and pavings n exc 15cm thickness (Below or above Ground level) complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks using PCC (1:3:6) type C1 (using 20mm graded stone aggregate), exceeding 10cm in width and setting in cement mortar (1:4) complete all as specified and directed.

M & L for Return, filling in surplus soil, back filling of retaining wall including spreading, leveling, watering and well ramming in layers not exceeding 25cm complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundations or mass concrete and filling complete all as specified and directed.

M&L for reinforced cement concrete (Design mix) M-30 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc., basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for 15mm thick plaster in CM 1:4 on fair face of brick walls or concrete surface including mixing of liquid water proofing compound@200ml per 50Kg cement bag, finished the surface even and smooth with out using extra cement complete all as specified. Note. WPC shall be measured and paid seperately

Supply only liquid water proofing compound. Make : Fosroc/ Dr Fixit/ Cicco

M&L for preparation of newly plastered wall surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed

Demolition of reinforced cement concrete(reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for all as specified and as directed.

Demolition of Precast cement concrete block walling built in CM or Cement lime Mortar complete all as specified and as directed.

M&L for Removing excavated material (any type of soil) to a distance not exceeding 50 metres and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Taking down cement plaster on concrete or brick masonry surface including raking out joints, hacking for key, scrubbing down with water etc to receive plaster complete all as specified and as directed.

M&L for complete removal of old decorated surface of walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed

Dismantling of wrought iron or mild steel work and structural steel work of any description ot otherwise provided for complete all as specified and as directed.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar works conforming to Fe-290, Gde-E-165 all as specified and as directed

M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed

M &L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates, etc. including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts, etc., of required size, on the top of the side of waist slab with suitable arrangement

M & L for reinforced cement concrete, design mix M-30 ( using 20mm graded crushed stone aggregate) in coloumns,pillars, piers, posts and struts complete all as specified and as directed.

M & L for reinforced cement concrete, design mix M-30 ( using 20mm graded crushed stone aggregate) in beams, cantilevers, bressumers,lintels over 1.5m span complete all as specified and as directed.

M&L formwork for rough finished flat surface to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and as directed.

M&L for formwork for rough finished surface of square, rectangular, or triangular surface to side of pillars, posts, struts, piers, column and stanchions complete all as specified and directed.

M&L for formwork to side and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc in rough finished flat surface complete all as specified and directed.

M & L for Cement concrete Type C2 1:3:6 (40 mm graded aggregate) in surface channels and drains etc. complete all as specified and directed.

Extra for forming fair finished drain or channel 45cm inner girth in cement concrete, using extra cement including forms, moulds, mitered / stopped ends etc complete all as specified and as directed.

M & L for reinforced cement concrete, design mix-30 (using 20mm graded crushed stone aggregate) in slabs supported on walls, beams, and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L formwork for fair finished flat surface to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M & L formwork rough finished surface of concrete to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work n. exc 10cm wide complete all as specified and as directed.

S&F 4mm thick polycarbonate sheeting(Hollow section) fixed with coach screws and washer in roof or wall etc complete all as specified and as directed.

Excavation in trenches n. exc 1.5m wide and exc 1.5m but n. exc 3.0m in depth in hard/dense soil for foundation, etc or for, shafts, wells, cesspits, manholes, pierholes, etc and n. exc 3 m in depth and getting out in hard/dense soil complete all as specified and directed

Rough excavation not exceeding 1.5m deep and getting out in hard/dense soil including clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots and trees not exceeding 30 cm girth (measured one metre above ground level) complete all as specified and directed

Removing building materials etc. (other than spoil payable under items 03028 to 03031 in section-3- Earthwork) to a distance exc 200m but n.exc 500m in low lying mod area or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and directed

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

S&F PVC (SWR) pipe 110mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive lain in trenches or in floors complete all as specified and as directed.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

S&F Galvanised 2 strand steel barbed wire 2.24 mm dia with 2mm barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire staples or steel pins etc complete all as specified and as directed.

M&L for preparation of old surfaces of steel surfaces exceeding 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for 20mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Excavating in post holes ( or similar holes) each n exc 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/dense soil.complete all as specified and as directed.

Dismantling of chain link fencing of any gauge and size not exceeding 4 Kg/Sqm .complete all as specified and as directed.

Supply only chain link fencing having mild steel dia of 5.2mm minimum, PVC colour coated securing with clips, nut bolts, etc.complete all as specified and as directed. Note : Fixing tie and nuts bolt etc will be measured and paid seperately.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and as directed.

M&L for Plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as mass concreting in foundation complete all as specified and as directed.

M&L Mild steel screw bolts diameter of neck 16 to 20mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm long. complete all as specified and as directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and as directed.

M&L for Removing excavated material (Soils) to a distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed

M&L for hardcore of gauge not exceeding 63mm deposited spread and levelled in layers not exceeding 15cm thick watered and rammed to a true surface of broken stone or boulders complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in path finish the top surfaces even and rough to receive top layer complete all as specified and directed

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, made of grey cement and pigments, machine pressed as in flooring, set, jointed and pointed in neat cement slurry laid over and including 20mm thick screed bed in CM (1:4) complete all as specified and as directed.

S&F Stainless steel screw bolts diameter of neck 4mm (machine made) with hexagonal or square heads at one end exc 2.5cm to 40cm long complete all as specified and as directed.

SKV Engineering

JD Construction

LOOK UP ENTERPRISES

M/S VISHAL CONSTRUCTION

V KARTHICK

SHUBHAM SHANKAR GAIKWAD

M/s Ramesh Lal