SPECIAL REPAIR TO BLDG NO P35 18 SRW AND ADDN ALTN TO COMPOUND WALL AROUND BLDG NO P253 P156 P157 AND P159 AT SULTANIA RETREAT 22 SRW AT SI LINES UNDER GE BHOPAL

Amount

Note : Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below:-

Demolition of brick work, built in Cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, ceilings, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets complete all as specified and directed.

Dismantling manglore pattern roof tiles, complete all as specified and directed.

Dismantling wooden fillets in rafter purlines etc unframed work under 40 sqcm in section complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position unframed wk complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed trusses complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking up or down 15 mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20 mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking down shutters of any description not exceeding 1 Sqm each, complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

Dismantling of water storage tanks of capacity 1000 Ltr and removing to store, complete all as specified and directed.

M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

S&F mild Steel work in tubular/structural trusses, purlins, mild steel plate etc including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 or steel sections conforming to Fe 410-W (Gde E-250) quality -A complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JINDAL]

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in ridges, etc, fixed with & including self tapping screws complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JINDAL]

S&F Mild steel conforming to Fe-290 Gde E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 m mean radius, built in cm 1:6 all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1: 6 on other than fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed. [MAKE: ACCOPROOF/WATER SEAL/MC BOUCHAMIE, MUMBAI/FOSROC/CICO/PIDILITE]

M&L for heavy duty flooring tiles, harsh weather & UV Resistance, high abrasion resistance, MOH Hardness >6, thickness 10 mm thick, area of each tile not less than 0.09 sqm, anti slip type, laid in floors, steps, edges, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tile with & including 15mm thick screed in CM 1:4 complete all as specified and directed. [MAKE:-JOHNSON ENDURA or equivalent in SOMANY/ KAJARIA/ORIENT as approved by GE]

M&L for Factory made, machine pressed, M-35 grade concrete interlocking paver blocks (glossy /reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 60 mm thickness with & including 50 mm thick stone dust cushion and joints filled with sand complete all as specified and directed. [MAKE:- MEHTAB / NAVYA TILES / SAP PAVERS/ SAGAR TILES]

S&F GI frame work size of grid 605 mm x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylong sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two eaqual flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kuled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed.

S&F asbestos free calcium silicate board of size 600x600x6mm, fixed to steel frame work in ceiling with & including applying two coats of oil bound distemper complete all as specified & directed. NOTE:- Cost of making frame work for light fittings, etc is deemed to be included in the quoted unit rate

S&F readymade decorative POP cornices (as per sample kept in GE office) size exceeding 75mm and not exceeding 125mm fixed on walls, ceilings, etc duly fixed with screws/adhesive complete all as specified and directed.

S&F Mild steel work conforming to Fe-290 Gde E-165 angle iron, flat iron, MS plate as in bracket, cleats, fasteners, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed., drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.

M&L for vitrified light shade flooring tiles, 10 mm thick (Square/ rectangular) polished, area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm, laid in floors, etc set and jointed in neat cement slurry and pointed in epoxy adhisive (Make :Dr.Fixit or Balendura) to match the colour of tiles with & including 15mm thick rendering in CM 1:4 complete all as specified and directed. [MAKE: SOMANY / KAJARIA / NITCO]

M&L for Joint free non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:6 complete all as specified and directed. [MAKE: SOMANY/ KAJARIA/ ORIENT/ JOHNSON]

M&L for Glazed ceramic coloured tiles 350mm x 250mm x 7mm thick or 300mm x 450mm x 7mm thick, in vertical surfaces such as skirting, dados and risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed. [MAKE: SOMANY/ KAJARIA/ ORIENT/ JOHNSON]

M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding, moulding and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S&F Butt hinges, extruded alluminium alloy with galvanised mild steel hinge pin, anodised and fixed, 100 mm size complete all as specified and directed.

S&F 150 mm Aluminium anodised barrel Tower bolts extruded section and fixed complete all as specified and directed

S&F 150 mm Aluminium handles, cast type, anodised complete all as specified and directed

S&F 300mm long aluminium alloy anodised Sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed

Supplying, fabricating and fixing powder coated (minimum thickness 50 micron) aluminium sections of required size for door, windows, ventilators frames and shutters and partitions including aluminium hinges of required size jointing cleats, screws sash fasteners, plug for fixing with walls, columns, etc complete all as specified and directed. [MAKE: JINDAL/ AJIT INDIA/ HINDALCO]

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.

S&F Tinted Sheet glass 4.8mm thick, ordinary quality and glazing with oil putty/rubber seal in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F Figured glass, pin head type 3mm thick and glazing with oil putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 150 mm Aluminium alloy body door stopper, cast type, anodised, withhard drawn steel spring fixed with doors, complete all as specified and directed.

S&F in repairs Aluminium extruded section body door closer, hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 75mm bore complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 15 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. [MAKE: TATA/ SURYA/ JINDAL/ PRAKASH]

S&F Steel water tubes, medium grade, ISI marked, galvanised, 20 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. [MAKE: TATA/ SURYA/ JINDAL/ PRAKASH]

M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

M&L for Providing cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, roof kerb, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M&L for 25mm thick Cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate in sub base, floor finishes complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

S&F two way Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8612) or equivalent in JAQUAR/MARC as approved by GE]

S&F Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8606) or equivalent in JAQUAR/MARC as approved by GE]

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed.

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet pan, pedestal pattern, ISI marked, white, including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed. [MAKE:-SOMANY (Cat No.120403 & 120404) or equivalent in CERA/PARRYWARE/HINDWARE as approved by GE.]

S&F in repairs plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminum hinging device complete all as specified and directed. [MAKE:-PRAYAG/SOMANY/CERA/PARRYWARE /HINDWARE]

S&F hand shower (health faucet) with 8mm dia 1.0 mter long flexible tube and wall hook complete all as specified and directed. [MAKE:- Prayag (Cat No.BH-76) or equivalent in JAQUAR/MARC as approved by GE]

S&F PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete all as specified and directed. [MAKE:- Prayag (Cat No.501 Smart flush cistern) or equivalent in PARRYWARE-SLIMLINE/CERA as approved by GE]

S&F in repairs Vitreous china bowl urinal flat back, white, with grating and union for discharge pipe including connections to flush pipe and outgoing pipes, complete all as specified and directed. [MAKE:-SOMANY (Cat.No.130205), PRAYAG (Cat No.4999) or equivalent in CERA/PARRYWARE/ HINDWARE as approved by GE.]

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed. [MAKE:-SINTEX/ POLYWELL/ POLYCON/POLYPLAST]

S&F Wash basin mixture, centre hole, cast copper alloy, screwed down, high pressure, with capstan head, fancy type, chromium plated screwed for iron pipe or for unions 15mm bore, complete all as specified and directed. [MAKE: PRAYAG (Cat.No.7250) or equivalent in JAQUAR/MARC/ PLUMBER as approved by GE]

S&F in repairs Vitreous china table top wash hand basin, white with brackets, including suitable PVC connection 450mm long, PVC (HDPE) 32mm bore waste pipe, 32mm CP brass coupling etc, complete all as specified and directed.

S&F corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf with chromium plated bracket guard and railing 300mm size complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-44) or equivalent in JAGUAR/CERA as approve by GE]

S&F PVC (SWR) floor/Nahani trap, plain with CP grating including jointing with solvent cement, dia of outlet 100 mm complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F Gun metal globe or gate valves, 20 mm bore, with iron wheel head, screwed both ends for iron pipe for the following bores including taking out old unserviceable valve complete all as specified and directed. [MAKE:-SANT / LEADER / RAMCO / ZOLOTO as approved by GE]

S&F Toughned glass 12mm thick, as in doors, partitions and similar work including cutting to shape, drilling holes as required, complete all as specified and directed.

S&F in repairs stainless steel hand rails, Gde 304 conforming to IS of approved design including ornamental fittings globes and all necessary drilling, bolting, riveting, welding etc. fixed in steps/floors steps etc. complete all as specified and directed. [Make - Jindal or equivalent as approved by GE]

M&L for 18 mm thick Plywood grade BWR, type BB fixed with screws to timber frame work, complete all as specified and directed.

M&L for 0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructions complete all as specified and directed.

S&F magnetic catches for cupboards with plastic body and striking plate not less than 40mm including fixed in, complete all as specified and directed.

S&F 75mm brass handle, cast type, polished bright, complete all as specified and directed.

S&F 40mm wide flap, continuous piano hinges, brass, bright finish, complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for Mild steel TMT Bar 6 to 8mmm dia cut to length, bent to shape to required, including cranking, bending spirally for hoping for columns, hooking ends and binding with and including mild steel wire (anneled ) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Reinforced cement concrete type B0, 1:2:4 (using 12.5mm graded stone aggregate) (nominal mix) in foundations, footing, plinth beams, bases for columns and mass concrete, complete all as specified and directed.

Use & waste of Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for fair finished flat surfaces of concrete complete all as specified and directed.

S&F Mild steel work conforming to Fe-290 Gde E-165 in bands, straps, supports or stays for rain water, including bolts, if required, hook and pintle hinges; handmade sliding bolts; clamps; hold fasts; hooks for hanging fans and similar small articles complete all as specified and directed.

S&F Collapsible steel gates, top hung, consisting for channel pickets, top and bottom runners, brass handles etc as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

M&L for preparing old painted steel & iron surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for Complete removal of existing treatment from walls and applying two coats of oil bound distemper over a coat of cement based putty complete all as specified and as directed. Note: Putty shall be measured and paid for seperately under respective item.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of cement based putty complete all as specified and as directed. (Note: Putty shall be measured and paid seperately.)

Preparation of old decorated surfaces of wall including brooming, scraping down smoke spot, moulds, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks and M&L for applying one coat of exterior weather proof water base emulsion paint on wall over a coat of white cement based putty, complete all as specified and directed. [MAKE : ASIAN (ACE) /SHALIMAR (SAKTIMAN) /BURGER (WALL MASTA)]

Preparation of newly plastered surfaces of wall and M&L for applying one coat of exterior weather proof water base emulsion paint on wall over a coat of white cement based putty, complete all as specified and directed. [MAKE : ASIAN (ACE) /SHALIMAR (SAKTIMAN) /BURGER (WALL MASTA)]

M&L for applying 3mm thick wall care putty (Make: Birla/JK) complete all as specified and directed.

M&L for providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat/curved surface for any shunk and raised moulding over GI framework and reinforced with GI wiremesh (fillets and GI wiremesh paid separately), complete all as specified & directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated materials (soil) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Demolition of Stone/boulder masonry, built in Cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Dismantling cement concrete louvers and jallies, 25mm thick, including all mouldings, complete all as specified and directed.

Boring holes 300mm dia and 4m deep, in soil for under reamed piles and getting out and disposal of soil to a distance not exceeding 50m, complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in foundations, footing, plinth beams, bases for columns and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in columns, pillars, posts & struts complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in lintels over 1.5m clear span, beams and cantilevers complete all as specified and directed.

Use & waste of Form work to sides of square or rectangular columns, pillars, posts and struts for fair finished surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides & soffits of lintels over 1.5m clear span, floor or roof beams, cantilevers, etc for fair finished flat surfaces of concrete complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement paint white or tinted over and including a coat of cement wash complete all as specified and directed.

M&L for Providing precast reinforced cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in louvers and jallies 25mm thick (measured solid) including all mouldings but excluding frame and set in cement mortar 1:4 complete all as specified and directed.

S&F PVC pipes, in any length fixed to compound walls as spouts, 100 mm bore complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets etc. to be measured separately), removing materials to store for keeping in safe custody or for taking credit and making good disturbed surface of walls, floors, etc.complete all as specified and directed.

M&L for point wiring complete for light/fan/exhaust fan on independent / combine with cable 1.50 sqmm (nominal area), FRLS PVC insulated, unsheathed, single core multi-stranded copper conductor cable, 1100 volts grade, ISI marked controlled by one one-way switch, drawn through and including concealed medium grade PVC conduit not less than 20 mm dia, ISI marked, with all accessories (PVC casing and capping of size 25 mm , ISI marked with complete accessories to be used wherever wiring to be run on ceilings and concrete surfaces) including one run of 1.5 sqmm FRLS muti-stranded copper conductor (green colour cable) as earth continuity wire connected to common earth dolly, including sunk sheet steel terminal box made out of 1.20 mm thick and not less than 60 mm in depth GI/MS/ pressed steel terminal box to be concealed in wall, duly painted with two coats of anti corrosive black bituminous paint over a coat of red oxide primer in and out sides and two coated of aluminium paint on internal surface , including laminated hylum sheet cover, ISI marked for mounting of fittings like switches, sockets, fan regulators, etc. fixed with galvanised screw and cup washer complete all as specified and directed. Note : (i) Wiring to be done as per approved colour code in IE rule.(ii) Rate includes chase cutting for concealed wiring. [Make of Cable : Polycab/ Plaza/ Havells]

All as per BOQ item No. 114.00 here-in-before, but for one switch socket combination 5/6 Amp on independent board, complete all as specified and directed.

All as per BOQ item No. 114.00 here-in-before, but for one three pin outlet 5 Amp on same board with other switches, complete all as specified and directed.

All as per BOQ item No. 114.00 here-in-before, but for one switch socket combination 6 pin 5 /15 Amp on independent board with wire of size 2.5 sqmm and 2.5 sqmm as earth wire, complete all as specified and directed.

All as per BOQ item No. 114.00 here-in-before, but for one switch socket combination 6 pin 5 /15 Amp on independent board with wire of size 4.0 sqmm and 4.0 sqmm as earth wire, complete all as specified and directed.

S&F modular switch, one way, 6 Amp, one module, 240 Volts, complete all as specified and as directed.

S&F modular bell push, 6Amp, one module, single pole, one way, 240 V, AC, 50 Hz, ordinary (IPXO), normal gap construction, unenclosed, flush type, screw type terminals, pattern no. 1, rocker type, design A complete all as specified and as directed.

S&F modular switch, one way, 16 Amp, one module, 240 Volts, complete all as specified and as directed.

S&F Modular socket outlets, two in one, three pin, 6 Amp, 2 modules, 240 V, AC, 50 Hz with earthing contact, controlled by one switch, complete all as specified and as directed.

S&F Modular socket outlets, two in one, three pin, 16 Amp, 2 modules, 240 V, AC, 50 Hz with earthing contact, controlled by one switch, complete all as specified and as directed.

S&F Ceiling rose surface bakelite, three terminals, 240V, 50Hz, ISI marked complete all as specified and as directed. [MAKE:-ANCHOR (PENTA series) or equivalent in LEADER/ CRABTREE/LEGRAND/HAVELLS as approved by GE]

S&F Bell, Ding Dong type, electric, single phase, 240 volt, AC complete all as specified and as directed. [MAKE:-ANCHOR (PENTA PC series) or equivalent in LEADER/ CRABTREE/LEGRAND /HAVELLS as approved by GE]

S&F LED tube light fitting, surface mounted lumanaires, 1 x 18 W, 240V, decorative ultra slim round /squar profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack with bipin holders, LED lamps, connector block, etc. complete with all accessories internally pre-wired and including connecting up with flexible copper conductor cable of suitable size complete all as specified and directed. Make : Havells Cat No : LHEXBLP7N1W018 or equivalant in C&G/Bajaj/Surya as approved by GE.

Supply & fixing LED light fitting mirror type with hig out put diffuser 2 feet, 10 watt, 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible coppder conductor cable of suitable size complete all as specified and as directed.

S&F Angle holder, PVC/Poly carbonate type with back plate suitable for batten fittings complete all as spcified and directed. [MAKE FOR HOLDER:-ANCHOR (PENTA PC series)/ LEADER/ CRABTREE/LEGRAND/HAVELLS as approved by GE]

S&F LED lamp 10 watt, B22 CDL complete all as spcified and directed.

S&F energy saving and environment friendly LED security light fitting of 30 Watt with high power LEDs with lens and IP 66 protection and luminaire housing is of pressure die cast aluminium alloy for heat sink for better heat heat transmission with polycarbonate cover and fixing on bracket of suitable size and making electric connection from light source to fitting with 1.5 sqmm PVC Aluminium stranded conductor 2 core of required length (approx 10 m) and testing on completion, complete all as specified and directed. [MAKE - ORIENT ELECTRIC Cat No LSFS-030-CF or equivalent in HAVELLS/CROMPTON/ WIPRO/BAJAJ as approved by GE]

S&F LED light luminaire 600mm x 600mm, 35/36 Watt, 240 V AC recessed type with high efficiency PMMA diffuser soft glare free light, complete with driver, holder and LED lamp suitable for roof ceiling, including connecting with driver three core flexible copper conductor cases of suitable size, complete all as specified and as directed.

S & F Modular fan regulator, 120 W, 2 modules complete all as specified and as directed.

M&L for sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core PVC insulated FRLS cable 1100V unsheathed with stranded copper conductor of 6.0 sqmm nominal cross section area and drawing into and including concealed 25mm dia, rigid non metallic PVC conduit, ISI marked, medium grade, inclusive of all fittings such as tees, bends, junction boxes, elbows, saddles, pipe hooks, couples, lock outs, etc and PVC insulated stranded copper conductor of 4.0 sqmm nominal cross section area as earth wire complete all as specified and directed. Note: - (i) Two runs of 6.0 sqmm cable, one run of 4.0 sqmm cable of earth continuity conductor & PVC conduit pipe shall be measured as one unit length. (ii) Cutting chases & making good for concealed sub main wiring will be measured and paid sepeartely under susequent item. [Make of Cable : Polycab/ Plaza/ Havells]

S&F in replacement factory made epoxy powder coated Distribution Board TP & N 4 ways (VTPN MCCB DB) and space for MCCB as incomer, with metal door (IP-43 protection) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including isolated Neutral Bar, Insulated busbar assembly, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE] NOTE:- MCCB shall be measured and paid seperatly.

S&F of MCCB 4 pole, 125 Amp, 16kA breaking capacity with complete electric connections by appropriate size of copper lugs including taking down old unserviceable DB complete all as specified and directed. Make :- Havells/Indo Asian /L&T.

S&F in replacement sheet metal enclosure double door type surface mounted concealed in wall 8 ways, 240 Volts, ISI marked 200 amps bus bar dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE] NOTE:- MCB shall be measured and paid separately.

S&F in repairs MCB SP, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 6 to 32 amps including connection with suitable size aluminium / copper lugs complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

S&F in repairs MCB SP suitable for 240 volts, AC supply 50 to 63 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

S&F in repairs MCB SPN suitable for 240 volts, AC supply 6 to 32 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

S&F in repairs MCB SPN suitable for 240 volts, AC supply 50 to 63 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

S&F sheet metal enclosure with socket plug top and MCB single pole and neutral enclosure with two pin & earth plug and socket complete with MCB 25 Amps, 240 volts complete all as specified and as directed.

S&F exhaust fan with louvers, AC Single phase 230/240 volts, 50 Hz, 250 mm sweep, 1200 RPM, 5 star rating, including nut bolt and connecting accessories, including cutting for making opening in wall and making good disturbed surfaces after fixing of exhaust fan and louvers including connection with 23/.0076 three core copper wire from ceilling rose to exhaust fan upto 1 mtr length complete all as specified and directed. [MAKE - HAVELLS or equivalent in USHA/ CROMPTON as approved by GE]

M&L for Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR-2009 Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by 15mm dia light grade GI pipe and watering pipe shall be 20mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed. NOTE :- (i) The concrete pit shall be PCC (1:3:6) type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) The unit rate includes the cost of GI pipe medium grade for protection of earth wire and 4mm dia earh lead wire upto 7.5 M. (iii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself.

S&F 40mm GI tubing light grade with all fittings as required for passing through cables under floors, along the wall or along the pole, etc with suitable size M.S.flat iron clamps incl nut,bolt and washer including taking down old rusted pipe complete all as specified and directed. [MAKE:-TATA / JINDAL / PRAKASH / SWASTIK as approved by GE]

Cutting of bituminous road/PCC hard standing/road/floor for laying of GI pipe upto 80mm dia (trench not more than 0.3m x 0.3m) for passing of cable including making good the disturbed surfaces all as per existing complete all as specified and directed. Note:-GI pipe shall be measured & paid separately under relevant items of this schedule.

Supply, laying, connecting and testing LT XLPE insulated, screened, PVC bedded, armoured, heavy duty cable with aluminium conductor of size 50 sqmm, 3.5 core, 1100 volts grade, laid in trenches, passing through pipes/ducts, etc including taking out old unserveciable cable, any type complete all as specified and directed. [MAKE:- POLYCAB /HAVELLS INDIA LTD/V-MARC as approved by GE]

M&L for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection (8 cm below cable & 15 cm above cable) complete all as specified and directed. [Note:-Compacted/punned thickness shall be measured & paid]

Supplying and laying sub class 'B' bricks (modular) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and directed.

Deduct schedule of credit (calculation will be done off line) Rs. 67300.00

M/s AKG Engineers & Contractors

PADAMSHRI CONSTRUCTION CO

M/s Khialdas Constructions

M/s Gulshan and Brothers

POONAM ELECTRIC INDUSTRY

RAJPATI CONSTRUCTION