Repairs to Roofs, Toilets, Rolling Shutters, Plumbing, Water Supply, Joinery and Misc B/R Works at Mil Station Bhusawal under GE (S) Ahmednagar

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15cm thick (below or above ground level) all as specified and as directed.

Demolition of cement concrete (un-reinforced) iof any description and in any position not otherwise specifically provided for all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles all as specified and as directed.

Taking down chowkats or frames with shutter (without taking out shutter from the frame), area n.exc 1.5 sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutter (without taking out shutter from the frame), area exc 1.5 sqm but not exc 4 sqm each all as specified and as directed.

Taking down shutters of any description, area n exc 1 sqm each all as specified and as directed.

Taking down shutters of any description, area exc 1 sqm and not exc 2sqm each all as specified and as directed.

Resecuring or easing & adjusting without taking down shutters of any description, area exc 1 sqm and not exc 2 sqm each all as specified and as directed.

Resecuring or easing & adjusting without taking down shutters of any description, area exc 2 sqm each all as specified and as directed.

Dismantling of AC sheets (corrugated, semi-corrugated etc) as in roof covering including ridges all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness in roof coverings complete all as specified and directed.

Dismantling of single layer mangalore pattern or similar tiles in roofing complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Dismantling battens for tiles, shingles etc. of any size including tilting fillets spaced exc 15 cm complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section, in any position, framed work, complete all as specified and directed.

Dismantling of kota stone slabs, Cudappah, granite stone slab & interlocking paver blocks of any descriptio or thickness in floor, apron etc laid bedded and pointed in any mortar all as specified an as directed.

Dismantling floor, hearth or wall tiling (Non skid ceramic tiles, glazed ceramic tiles, vitrified tiles, chequered cement concrete tiles etc) including cement mortar bedding but not backing complete all as specified and as directed.

Dismantling wrought or mild steel work of any description not otherwise provided for in any position complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for re- fixing all as specified and as directed.

Excavation in post holes, in soft / loose soil each not exceeding 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick, watering and removing surplus soil to a distance not exceeding 50 M and making good surface complete all as specified and as directed.

M&L for post construction anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in apron .complete all as specified and as directed.

M&L for post construction anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerocene based solution) @ 0.5 litre per /hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same all as specified and as directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L for PCC, 1:3:6, type C2 (using 40 mm graded stone aggregates) in foundations, filling and mass concrete complete all as specified and as directed .

M&L for brick work with sub class 'B' bricks, old size, straight or curved on plan exc. 6 metre mean radius, built in cement mortar 1:6 all as specified and as directed.

M&L for second class hard wood wrought scantling fixed in position complete all as specified and as directed.

M&L for clean sawn second class hardwood battens for tiles, sectional area exc 5 Sqcm and not exc 15 Sqcm, fixed at 30 cm centre to centre complete all as specified and as directed.

All as per serial item No. 29 but except battens. Note : Old serviceable battens retrived from dismantling shall be used.

M&L for 15mm thick, second class hard wood boarding, planed one side with edges tongued and grooved or rebated, as in eaves board/ barge board etc. complete all as specified and as directed.

S&F solid PVC wall lining consisting of 5mm thick single side prelaminated PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing including dismantling existing wall lining all as specified and as directed.

S&F 5 mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC frame all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47 mm, made out of 5 mm thick, plain colour, PVC sheet, reinforced with MS square tube all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick [style] consisting of a frame made out of MS tubs for top and bottom rails,MS frame shall be covered with heat molded plain colour PVC `C` channel having a PVC steel strip of 20mm width stuch inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side and as gap inseert for top rail and bottom rail, Panneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable sheet beading, and joined together withj solvent cement, supplying & fixing in the frame at site all as specified and as directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows & other frames/ chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200N (Face) & 1100N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (suspension grade), Calcium Carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (face) & 900 N (edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and as directed.

S&F second class hardwood, plain, solid, straight chowkat & frames, wrought, framed rebated on the solid, rounded or chanfered, put together with glue pinned at joints all as specified and as directed.

S&F flush shutter, 40 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and as directed.

S&F 35 mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, guaze, etc divided into squares with plain chamfered or rounded, mitred and rebated sash bars, any numbers, edge of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc. size of members as specified in SSR part -I, clause 8.24(a) all as specified and as directed.

S&F 30 mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, guaze, etc divided into squares with plain chamfered or rounded, mitred and rebated sash bars, any numbers, edge of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc. size of members as specified in SSR part -I, clause 8.24(b) all as specified and as directed.

S&F 100mm size mild steel butt hinges, medium weight colled rolled and fixed with welding to existing mild steel pressed steel chowkat/shutter all as specified.

S&F 75mm size mild steel butt hinges medium weight colled rolled and fixed with welding to existing mild steel pressed steel chowkat/shutter all as specified.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised and fixed all as specified and as directed.

S&F 125mm size extruded aluminium alloy handles, fabricated type, anodised and fixed all as specified and as directed.

S&F 150mm size aluminium anodized barrel tower bolts of extruted section and fixed all as specified and as directed.

S&F 200mm size aluminium anodized barrel tower bolts of extruted section and fixed all as specified and as directed.

S&F 300mm long aluminium alloy anodised sliding door bolts with hasp, staple and fixing clip of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast- aluminium alloy all as specified and as directed.

S&F 250mm long aluminium alloy anodised sliding door bolts with hasp, staple and fixing clip of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast- aluminium alloy all as specified and as directed.

S&F in repairs, 150mm size extruded aluminium alloy handles, fabricated type anodised and fixed all as specified and as directed.

S&F in repairs, 100mm size extruded aluminium alloy handles, fabricated type anodised and fixed all as specified and as directed.

S&F in repairs, 150mm size aluminium anodized barrel tower bolts of extruted section and fixed all as specified and as directed.

S&F in repairs, 200mm size aluminium anodized barrel tower bolts of extruted section and fixed all as specified and as directed.

S&F in repairs, 300mm long aluminium alloy anodised sliding door bolts with hasp, staple and fixing clip of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast- aluminium alloy all as specified and as directed.

M&L for stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.4mm and fixed with stanless steel staple to wooden/steel frames all as specified and as directed.

M&L in repairs, for stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel staple to wooden/steel frames all as specified and as directed.

S&F in repairs, double action floor spring, hydraulically regulated, made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified and as directed.

S&F steel windows with side hung shutter including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovateiled or welded all as specified and as directed.

S&F steel ventilator with top hung shutters including hinges steel peg stay, complete all as specified and as directed.

S&F powder coated aluminium door with frame and shutter in two panels (top and bottom) made out of aluminium sections (make Jindal or equivalent) including 5 mm thick sheet glass, aluminium cleats, rubber/ neoprene beading, all necessary fittings and locking arrangements etc all as specified and as directed and comprises of following sections :- (a) Vertical style- 47 x 44.5 x 2.25 mm thick @ 1.15 Kg/m (Min) (b) Lock rail- 114.6 x 44.45 x 2.3mm thick @ 2.06 Kg/m (Min) (c) Bottom rail-114.6 x 44.45 x 2.3mm thick @ 2.06 Kg/m (Min) (d) Frame-47.5 x 44.45 x 2.25 mm thick @ 1.12 Kg/m (Min)

S&F powder coated aluminum windows, three track, made out of aluminium sections (make Jindal or equivalent) including all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprises of following sections :- (a) Window frame (i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Size - 20672 (Wt not less than 0.594 Kg/m) (b) Shutter (i) Vertical (end)- 20669 (Wt not less than 0.481 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m)

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or rivetted, or forged into spikes, framed guared bars, barred iron doors and similar work conforing to Fe 290.Gde-165 all as specified and as directed

M&L for framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 all as specified and as directed

S&F mild steel work as in wind ties for roof sheets, including securing bolts, necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F mild steel work confirming to Fe-290 grade E-165 as in bands, straps, supports for rain water pipes or stagged, hold fasts & similar small articles complete all as specified and as directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters: purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates, conforming to Fe 410-W(Gde-E-250) quality-A, complete all as specified and as directed.

S&F mild steel screw bolts, (machine made), 5 to 10mm dia, exc 5cm but n exc 10cm long, with hexagonal or square heads at one end and screwed the other, fitted with washer and one nut, complete all as specified and as directed.

Repairs to mild steel rolling shutters, area not exc 20Sqm each including greasing, oiling, etc., and making smooth functioning including taking down if required and fixed in position complete all as specified and as directed.

M&L for anodised aluminium snap grid frame work of grid size 605mm x 605mm for false ceiling with and including 4mm thick non asbestos fibre cement building boards (decorative type), fixed or laid/inserted in aluminium frame work/grid, 6mm dia GI hangers (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40mm x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long, including preparation of new ceiling surfaces and applyig two coats of distemper oil emulsion over a coat of chalk whiting complete including dismantling false ceiling with frame work, cover fillets etc all as specified and as directed.

M&L for galvanised corrugated mild steel sheeting, 0.63 mm thick, with two corrugations side lap, fixed with coach screws and washers, in roofs, wall etc. with grade of zinc coating 275, complete all as specified and as directed.

All as per serial item No. 70 but except sheets Note : Old serviceable sheets retrived from dismantling shall be used.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet, 0.5 mm thick of any colour having tensile strength of 550 Mpa as in ridge/roof covering / cladding to wall fixed with self tapping screws all as specified and as directed.

M&L for 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc. fixed with L-type or J-type or cranked hook bolts all as specified and as directed.

M&L for 6mm thick asbestos cement two piece serrated ridge for corrugated or semi-corrugated sheets fixed with L-type or J-type or cranked hook bolts all as specified and as directed.

M&L for roof tiles, Mangalore pattern, interlocking at side joints, laid dry complete all as specified and as directed .

All as per serial item No. 76 but except tiles. Note : Old serviceable tiles retrived from dismantling shall be used.

M&L for ridge or hip tiles to suit Mangalore pattern roofing tiles, bedded and jointed in cement mortar 1:6, complete all as specified and as directed.

All as per serial item No. 78 but except ridge tiles. Note : Old serviceable ridge tiles retrived from dismantling shall be used.

S&F in repairs, 18/19mm thick block boards, grade 1 quality, exterior grade, decorative type with decorative face veneers on one face fixed to timber frame work with external teak wood lipping 6 mm thick all as specified and as directed.

S&F in repairs, 12 mm thick prelaminated particle board exterior grade, prelaminated on one side with decorative choice lamination fixed with screws to timber frame work as in pelmet boxes all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for 75mm thick plain cement concrete 1:4:8, type D2 using 40 mm graded stone aggregate as in sub base finished even and fair complete all as specified and as directed.

M&L 25mm thick plain cement concrete 1:2:4, type B0 using 12.5 mm graded stone aggregate as in flooring finished even and smooth complete all as specified and as directed. Note : This item shall not be executed as 'Sub base'

M&L for anti skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tile exc 0.11 sqm but n exc 0.18 sqm in floors laid over and including 15mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles all as specified and as directed.

M&L for glazed ceramic coloured tiles 350 x 250 x 7mm thick / 450 x 350 x 7 mm thick on vertical surfaces over and including 10mm thick cement plaster in cement mortar 1:4 as in backing coat, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles complete all as specified and as directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set and jointed and pointed in neat cement slurry with grey cement and pigment in floors, over and including 20mm thick screed bed in cement mortar 1:6 in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, complete all as specified and as directed.

Precast cement concrete interlocking tiles (glossy finish/ rubber mat finish) of 80 mm thick ,hydraulically pressed cemented tiles of grey colour with pigments, (glossy finish/ rubber mat finish) factory made, M-40 grade conforming to IS-15658-2006, as in floor laid over & including 25 mm thick sand cusion and including filling of interstices with fine sand complete all as specified and as directed. (Note : Size, shape & pattern of tiles shall be as approved by GE).

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces (external ) in cement mortar 1:4, finished even and fair complete all as specified and as directed

M&L for rendering 10 mm thick on other than fair faces of brick work or concrete suraces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed

M&L for preparing new plastered wall surfaces of walls and applying two coats of distemper oil emulsion over a coat of chalk whiting complete all as specified and as directed

M&L for preparation of newly plastered or unplastered surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and as directed

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads all as specified and as directed.

S&F 3mm thick plain sheet glass, ordinary quality and glazing with oil putty or wooden beading, size not exc 0.5 sqm in each pane all as specified and as directed.

S&F 3mm thick ground, obscured or frosted glass and glazing with oil putty or wooden beading all as specified not exc 0.5 sqm in each pane all as specified and as directed.

M&L for preparation of new surfaces of wood or wood based materials of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for preparation of new wood and wood based surfaces, new of any description and girth not otherwise described and treated with two coats of creosote oil complete all as specified and as directed.

M&L for preparation of new wood and wood based surfaces of tiles battens any size and spacing, prepared and teated all over creosote oil (measured overall on one side only, spaces not deducted) complete all as specified and as directed.

M&L for 15mm bore GI tubing medium grade with all fittings and fixed (concealed) complete on walls and ceilings or laid in floors etc complete all as specified and as directed. (Note. The rate of cutting chases and making good the surface is deemed to be included in the unit rate quoted by the contractor)

Fixing only 15mm bore GI tubing medium grade with all fittings (new) and fixed (concealed) complete on walls and ceilings or laid in floors etc complete all as specified and as directed. (Note. The rate of cutting chases and making good the surface is deemed to be included in the unit rate quoted by the contractor)

M&L for 20mm bore GI tubing medium grade with all fittings and fixed (concealed)complete on walls and ceilings or laid in floors etc complete all as specified and as directed. (Note. The rate of cutting chases and making good the surface is deemed to be included in the unit rate quoted by the contractor)

Fixing only 20mm bore GI tubing medium grade with all fittings (new) and fixed (concealed) complete on walls and ceilings or laid in floors etc complete all as specified and as directed. (Note. The rate of cutting chases and making good the surface is deemed to be included in the unit rate quoted by the contractor)

S&F 16 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. Note : Replacement of taken down GI tubing 15mm bore.

S&F 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. Note : Replacement of taken down GI tubing 20mm bore.

Disconnecting existing water tanks of 500 litres capacity, setting aside (or lowering if required) for cleaning and removing all scale and dirt, etc. from tanks and mouths of circulating pipes etc. and hoisting reconnecting and re-fixing in position complete all as specified and as directed.

Disconnecting existing water tanks of 1000 litres capacity, setting aside (or lowering if required) for cleaning and removing all scale and dirt, etc. from tanks and mouths of circulating pipes etc. and hoisting reconnecting and re-fixing in position complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 500 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting including dismantling existing water tanks of capacity exc 250 litres and n exc 500 litres all as specified and as directed.

All as per serial item No 108 but 1000 litres capacity water storage tank including dismantling existing water tanks of capacity exc 500 litres and n exc 1000 litres all as specified and as directed.

S&F in repairs, 15 mm bore pillar taps, cast copper alloy with capstan heads, fancy type, chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repairs, 15mm dia bib tap, cast copper alloy, fancy type, chromium plated, capstan head screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs, 15mm dia stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F in repair, brass chromium plated mixer for mixing hot and cold water, 15mm bore, screwed down for iron pipe and fixed complete all as specified and as directed.

S&F in repairs, 600mm long PVC connections 15 mm size with PTMT nuts complete all as specified and as directed.

S&F in repairs, ball valves high pressure PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 20 mm bore iron pipe (Minimum weight 210 gms), complete all as specified and directed.

S&F in repairs, ball valves high pressure PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 25 mm bore iron pipe (Minimum weight 455 gms), complete all as specified and directed.

S&F in repairs, chromium plated shower rose with or without swivel joints, 125mm size, including fixing to steel pipe or union etc complete all as specified and as directed.

S&F in repairs 15 mm bore bib tap PTMT of any colour as approved by GE, screwed for iron pipes and fixed complete all as specified and as directed.

S&F in repairs 15 mm bore pillar tap PTMT of any colour as approved by GE, screwed for iron pipes and fixed complete all as specified and as directed.

S&F in repairs vitreous china squatting pan, white, Orissa pattern of size 580mm x 440mm with integral foot rest, P or S trap, set in cement concrete including flush pipe and connecting to trap / flushing cistern and making good to floor complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet ( pedestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S & F in repairs, 10 Litres capacity PVC valveless syphonic action type, flushing cistern, low level, white or coloured, with inlet, ball valve, float and handle including brackets etc complete all as specified and as directed.

S & F in repairs vitreous china wash hand basin, white flat back size 550 mm x 400 mm including brackets including pillar tap, 15 mm bore chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe, 450mm long 15mm dia PVC connection pipe complete all as specified and as directed.

S&F in repairs, CP health faucet (ABS body hand shower) suitable for 15 mm dia pipe, with 1250 mm long flexible tube and ABS wall hook including making connections and fixed in position all as specified and as directed.

S&F in repairs, 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repairs, 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S&F in repairs, 110mm bore PVC (SWR) branch piece, double (Double Y) equal or unequal with access door, all as specified and as directed

S&F in repairs, 110 mm dia PVC (SWR) bends with access door, of any radius, complete all as specified and as directed

S&F in repairs, 110 mm dia PVC (SWR) bends of any radius, complete all as specified and as directed

S&F in repairs, 75 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repairs, 75 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints,fixed to wall all as specified and as directed.

S&F in repairs, 75mm bore PVC (SWR) branch piece, single (Single Y) equal or unequal with access door, all as specified and as directed

S&F in repairs, 75 mm dia PVC (SWR) bends with access door, of any radius, complete all as specified and as directed

S&F in repairs, 75 mm dia PVC (SWR) bends of any radius, complete all as specified and as directed

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed to wall with brass screws complete all as specified and as directed

S&F in repairs tubular towel rail, brass chromium plated, 20mm dia, D type, 60cm long between flanges, fixed with brass screws to wall complete all as specified and as directed

Bhirud Electric Stores

CHAUDHARY AND ASSOCIATES