PROVISION OF DEFICIENT OTM ACCN FOR 300 ORs AT AOC CENTRE SECUNDERABAD

Amount

Lumpsum price worked out by the tenderer for BUILDINGS / STRUCTURES as listed in Schedule ‘A’ Part-I

Lumpsum price worked out by the tenderer for SITE CLEARANCE AND DEVELOPMENTS as listed in Schedule ‘A’ Part-II

Lumpsum price worked out by the tenderer for INTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-III

Lumpsum price worked out by the tenderer for INTERNAL ELECTRIC SUPPLY as listed in Schedule ‘A’ Part-IV

Lumpsum price worked out by the tenderer for RCC RETAINING WALL as listed in Schedule ‘A’ Part-V

Lumpsum price worked out by the tenderer for ROAD / PATH / CULVERT as listed in Schedule ‘A’ Part-VI

Lumpsum price worked out by the tenderer for SEWAGE DISPOSAL as listed in Schedule ‘A’ Part-VII

Lumpsum price worked out by the tenderer for AREA DRAINAGE as listed in Schedule ‘A’ Part-VIII

Lumpsum price worked out by the tenderer for FENCING, GATE AND COMPOUND WALL as listed in Schedule ‘A’ Part-IX

Lumpsum price worked out by the tenderer for RAIN WATER HARVESTING as listed in Schedule ‘A’ Part-X

Lumpsum price worked out by the tenderer for EXTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-XI

Lumpsum price worked out by the tenderer for EXTERNAL ELECTRIC SUPPLY as listed in Schedule ‘A’ Part-XII

Lumpsum price worked out by the tenderer for COOLING APPLIANCES as listed in Schedule ‘A’ Part-XIII

Lumpsum price worked out by the tenderer for FIRE FIGHTING SYSTEM as listed in Schedule ‘A’ Part-XIV

Lumpsum price worked out by the tenderer for DEMOLITION OF BUILDINGS as listed in Schedule ‘A’ Part-XV

SCHEDULE 'A' PART XVI (ROOF TOP SOLAR POWER PLANT) Note: This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under column 5 signifies this fact only.

Design, procure, erect, install, testing and commission of Grid connected solar photovoltaic plant of 20 KW capacity (roof top) including solar photovoltaic Module, DC cabling, AC cabling, Module Mounting Structures, Combining Boxes, Lightning Protection of SPV modules and other accessories, string inverter including connecting to local utility grid etc., all as per Srl Item No.1 of Sch 'A' Part- XVI (ROOF TOP SOLAR POWER PLANT)

SCHEDULE 'A' PART XVII (D G SET FOR PUMP HOUSE) Note: This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under column 5 signifies this fact only.

Supply, installation, testing and commissioning of silent Diesel Engine driven generating set 415 volts, 3 phase 4 wire, engine as per IS:10001/ 10002 and Alternator as per IS: 13364, water cooled, diesel engine developing 83 BHP at 1500 RPM including AMF control panel for 62.5 kVA DG Set with fuel tank capacity 150 Ltrs capacity with standard manual control panel and batteries with relay panel and switch gears for automatic starting on main failure, control panel having meter and sound proof canopy as per latest CPCB norms and foundation (height of the foundation should not be less than 45cm from ground level) etc. of capacity 50kW /62.5 KVA mounted on base frame complete all as per Srl Item No.1 of Sch 'A' Part- XVII (D G SET FOR PUMP HOUSE)

SCHEDULE 'A' PART XVIII (MISCELLANEOUS ITEMS) Note: This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under column 5 signifies this fact only.

INTERNAL ELECTRIC SUPPLY

Supply, fix, test and commissioning of Energy efficient LED light fitting surface and wall mounted LED batten 20 Watts, 4 Feet with polycarbonate housing & integrated electronic driver, prewired with all accessories, complete all as per Cat No.LUMILINEPLUSBS20WLED865SPCSS of Havells or techno-commercially equivalent of other specified makes fixed on surfaces of wall or ceiling and connecting of flexible copper conductor cable twin core of suitable size from ceiling rose to fitting drawn through and including flexible conduit, fixed with suitable mounting clamps etc., complete all as specified and as directed.

Supply, fix, test and commissioning of Wall mounted decorative luminaire suitable for LED lamp B22 base light fitting with and including LED adore lamp 5Watts, min 500 lumen with B22 base cap, CDL 3 star lamp, 6500K all as per Cat No.LHDL07150099 (For Fitting), LHLDEUEEMK8R005 (For Lamps) of Havells or techno-commercially equivalent of other specified makes connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size etc., complete all as specified and as directed.

Supply, fix, test and commissioning of LED adore lamp 9Watts, min 850 lumen with B22 base cap, WW 3 star lamp, 3000K all as per Cat No.LHLDEUEEMC8R009 of Havells or techno-commercially equivalent of other specified makes complete all as specified and as directed.

Supply, fix, test and commissioning of LED street light luminaires, outdoor type 25Watts new generation energy saving and environmental friendly long life made up of pressure die cast aluminium housing with high efficient LED as lighting source and lens embedded PC cover having top opening separate driver compartment with IP66 protection and impact resistance of IK07, suitable for pole dia Ø 43 mm (max.) all as per Cat No.ENDURAPEARLSL25WLED757S ASYTOPCMP of Havells or techno-commercially equivalent of other specified makes connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket, complete all as specified and as directed.

Supply and Fix Telephone socket modular type RJ11 with shutter all as per Cat No. 5734 26 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed.

Supply and Fix TV CO-Axial socket outlet modular type all as per Cat No. 5736 25 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed.

Supply, fix, connecting and testing factory made, distribution board, (MCCB DB) fitted with Bus Bars, Neutral Links, blanking plates (without MCCB), Vertical type, TPN, 4 way, having degree of protection IP 43 with metal double door, 415 Volts, flush type made out of 1.2mm thick CRCA sheet metal, duly powder coated and conforming to IS 8623 with 200 Amps rated copper bus bar with neutral link all as per Cat No.DHDLVDRWGOFO04 of Havells or techno-commercially equivalent of other specified makes with provision for MCCB as incomer and SP/TP MCBs as outgoing complete concealed and fixed flush to wall and making good the disturbed surfaces etc., complete all as specified and as directed.

EXTERNAL WATER SUPPLY

Supply, lay and testing Ductile Iron pressure pipes of size 100mm bore with spigot & socket ends, cast special, class K7 conforming to IS 8329 with inside surface of centrifugally cast cement mortar lined and outside with zinc coating suitable for tyton joint (Push-on joint) in any length laid to level or to falls in trenches/ on grounds / on supports including DI specials as required at site and jointing with flexible push-on type gasket of electrometric (EPDM) joining materials conforming to IS:5382 and making good for disturbed surfaces of roads, path ways etc while laying the pipe line at site, site clearance for the route of pipe line, welding, cutting the existing CI/DI/MS pipe line of any size up to 400 mm dia for inserting branch connections etc complete all as specified.

Note: (a) The unit rate quoted shall be deemed to include the cost of push-on type gasket joints. (b) Excavation and earthwork, Returning, filling in and removal of soil shall be measured and paid separately under relevant items. (c) Lead Joints / D-Joints will be measured and paid separately. (d) The contractor is responsible for obtaining the approval from Police Department for Traffic Diversion and related works if required in consultation with the MES department. (e) Contractor is responsible for repair/ replacement of any damages to the existing structures, Under Ground HT/LT/OFC Cables etc during the course of execution.

Supply, Install, testing and commissioning of horizontal mounted monoblock centrifugal pump set, electric operated with energy efficient motor conforming to IS:12615, shaft made of carbon steel having discharge capacity 600-300 LPM at 15-30m head, 3000RPM, 3phase, 300-440 volt, comprising of motor & pump with impeller, motor body, suction and delivery casing made cast iron, inbuilt strainer, sealing arrangement - Gland packing, designed for automatic air release during priming, dynamically balanced rotating parts ensuring minimum vibration during running, gland packed/suction & delivery pipe size 65x50mm all as per Cat No.MBNH52FS of Crompton or techno-commercially equivalent of other specified

makes with necessary base frame for pump set using angle iron of suitable size for base and frame complete as required at site including foundation bolts of suitable dia and suitable length including electrical connections from starter to motor, necessary civil works & PCC works complete to with stand the vibrations all as per manufacturer instructions and motor covering hood of hard plastic for protection from rain etc., complete all as specified and directed.

Supply and fix foot valve of size 65mm with strainer, plastic material, threaded type, fixed to the suction side of the pump line with necessary fittings and fixtures complete all as specified and as directed.

Supply and fix Cast Iron Non return valve (Reflux valve) of size 65mm bore, flanged ends in swing type design with rubber seat, single disc with all accessories confirming to IS 5312-2004 and ISI marked, type PN 1.6, Cast Iron body including suitable rubber gasket joints with suitable bolts, nuts and washers etc., jointing and testing complete all as specified and as directed.

Supply and fix Cast Iron Sluice valve of size 100mm bore with stem of Stainless Steel (AISI410) and bronze (Gun metal) working parts and Cast Iron body with clamps and check nuts, operating hand wheel, both ends flanged and drilled confirming to IS 14846-2000, non rising type K504, class PN 1.6 including jointing materials with suitable bolts, nuts and washers etc., jointing and testing complete all as specified and as directed.

Supply and fix Cast Iron Sluice valve of size 80mm bore with stem of Stainless Steel (AISI410) and bronze (Gun metal) working parts and Cast Iron body with clamps and check nuts, operating hand wheel, both ends flanged and drilled confirming to IS 14846-2000, non rising type K504, class PN 1.6 including jointing materials with suitable bolts, nuts and washers etc., jointing and testing complete all as specified and as directed.

Design, Fabricate, Supply, Install, testing and commissioning of LT cubicle panel board, 3 Phase 4 wire system (factory made of approved CPRI) of size as recommended by IS & CPRI norms, outdoor type double door front and back opening type, sloped canopy (Hood) on top extended 100mm all around made out of CRCA sheet 3.0 mm thick dust proof, duly treated through 7 tank pre treatment process and painted with epoxy powder coated mat finish of Siemens Grey structural RAL 7032 shade colour, built in industrial type locking arrangement on front and back with separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 25 Sqmm x 4.0 core in and out, incoming

and out going feeders duly marked on revited plates suitable for working on 415 volt AC supply including bus bar chamber and copper bus bar of capacity 32 Amps rating for phase and neutral mounted on hygroscopic insulator fixed in a separate bus bar chamber separate compartment for incoming and outgoing feeder and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs ,Panel mounted on Angle iron frame of 50x50x6mm thick duly painted and embedded in PCC 1:3:6 45 CM below ground level and 15 Cm above ground level and consisting the following:- (for Pump House)

(a) Bus bar aluminium duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic,non combustible,track resistant high strength FRP insulators 200 Amps for phases and neural set of 4 for RYB &N set of 04 -01 set (b) MCCB Four Pole 415 Volts 50 Hz 40 Amps adjustable Thermal and Fixed Magnetic type with repturing capacity of 16 KA - 01 No. (as Incoming) (c) Start Delta starter fully automated suitable for 415V AC having capacity 5.0HP-02 Nos (d) MCB Three Pole 415 Volts 50 Hz 25 Amps fixed type 35 KA repturing capacity - 02 Nos. (as out going) (e) MCB DP 6-32 Amps - 02 Nos.

Construction of valve chamber of internal size 600 x 600 x 600mm including necessary earth work excavation, PCC 1:4:8 in foundation type D2 using 40mm graded stone aggregate, brick wall in CM 1:4 using old size bricks, PCC 1:2:4 type B1 for coping, 15mm thick rendering in CM 1:4 including provision of MS sheet cover 3.0mm thick with MS angle frame 40 x 40 x 6mm all round and at diagonals of size 40 x 40 x 6mm and also MS plate welded to MS angle as shown in drawing, embedded in concrete with suitable hinges and locking arrangements, including two coats of synthetic enamel paint over a coat of red oxide primer etc, complete all as specified and as directed.

Material and labour for Core cutting of existing UG Sump for creating opening of pipes to fit through suitable for 80mm dia GI/DI/CI pipe including necessary packing with binding agents after fixing of pipe into UG sump etc., complete all as specified and as directed.

EXTERNAL ELECTRIC SUPPLY

Material and labour for road crossing/drain crossing by adopting trenchless tunneling work through specified pipe jacking method by erecting the equipment to true to the alignment and gradient by hydraulic pipe jacking technique complete including tunneling, excavation in any type of soils, hard rock etc., and including provision of MS casing pipe heavy duty of size 150 mm dia with 6 mm thick in any length with jointing materials to carry LT UG cables of size upto 400 Sqmm and necessary conveyance charges of machinery and other required materials in co-ordination with the concerned authorities etc., complete all as specified and as directed.

Supply, Installation, testing and commissioning of transformer platform/ plinth mounted type of capacity 160 KVA step down, Energy Efficiency Level 2, outdoor type, copper wound, vector group DYN, 11/0.433 KV, AC, 3 Phase, 50Hz on secondary side double wounded, oil immersed, naturally air cooled with external cooling tubes/ radiator having tapping at (±) 2.5%, (±)5%, (±) 7.5% changed by hand operated OFF Load tap changing gear, the maximum temp rise not exceeding 40 Deg in oil and 45 Deg in HV/LV winding when measured by the resistance method after continuous full load run in ambient temperature of 50 Deg and the transformer confirming to IS 1180(Part-I)-2014 (Level-II) amended up to date and comprising of following accessories:-

(a) 3 Nos porcelain HV bushing with arcing horns on HV side suitable for 11 KV complete with bushing rods, nuts and washers etc. (b) 1 No cable box on LV side consisting of 04 Nos porcelain bushing with bushing rods, nuts, washers with cable gland of suitable size for reception of cable. (c) Oil conservator tank with filler type drain valve. (d) Dehydrating breather assembly with first filling of Silica gel. (e) Explosive vent with double diaphragm & sight glass. (f) Thermometer Pocket on tank cover.

(g) Two earthing terminals on transformer body to facilitate fixing of 32x6 mm GI strips (h) 1 No of thermometer dial type, vapour pressure type having range 0-120 Deg (j) Rating and terminal marking plate. (k) Oil level gauge. (l) Oil filling port on top cover with plate. (m) Air release valve. (n) Lifting lugs (o) 4 Nos plain solid cast steel detachable rollers. (p) Extra bushing for neutral, outside the cable box for providing independent earthing (q) First filling of new transformer oil confirming to relevant IS and tested upto 60KV dielectric strength at 2.5mm Gap (r) Cooling valves (s) Filter valves

Design Fabricating supply and errecting connecting and testing totally enclosed LT cubicle panel board 3 Phase 4 wire system outdoor double door front and back opening type, sloped canopy (Hood) on top extended 100mm all around, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 120 Sqmm 3.5 core in and out, incoming and out going feeders duly marked on revited plates etc complete CPRI approved factory made fabricated out of 3mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy powder coated mat finish of SIEMENS GREY structural RAL 7032 shade colour,built in industrial type locking arrangement on front and back, and pre wired with PVC insulated

multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, Panel mounted on Anle iron frame of 50x50x6mm thick duly painted and embeded in PCC 1:3:6 45 CM below ground level and 15 Cm above ground level and consisting the following (Main Incoming Panel Board) (a) Bus bar aluminium duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic,non combustible, track resistant high strength FRP insulators 500 Amps for phases and neural set of 4 for RYB &N set of 04 - 01 set

(b) MCCB Four Pole 415 Volts 50 Hz 320 Amps Adjustable Thermal* & Fixed Magnetic setting Ics = 75% of Icu, type with repturing capacity of 50 KA - 01 No. Make Havells Cat No- IHLLNFBF0320 # . (c) MCCB Four Pole 415 Volts 50 Hz, 100Amps Fixed Thermal & Fixed Magnetic setting | Ics = 75% of Icu, type with repturing capacity of 16 KA - 03 No. Make Havells Cat No- IHLGNF0100 # (02 for bldg and 01standby) (d) MCCB Four Pole 415 Volts 50 Hz 40 Amps Fixed Thermal & Fixed Magnetic setting | Ics = 75% of Icu, type with repturing capacity of 16 KA - 02 Nos. (01 Pump House and 01 No Cook house).

Supply, Install, testing and commissioning of LT feeder pillar box, factory made, CPRI approved, Indoor type floor mounting with channel iron pedestal frame made out of 2.00 mm thick CRCA sheet steel and MS angle section 40x40x6mm base frame compartmental type, dust proof, free standing, suitable for working on 440 volts 3 phase 50 Hz A C supply, vermin proof, front and rear opening, hinged doors etc powder coated as per seven tank process and IP 54 protection, cable alley, cable entry hole at the bottom, earth strip 32x6mm , 3 phase and neutral copper bus bar of 300 amps with non adhesive color coded insulation sleeves mounted on insulators, drilled holes on bus bar strips for tapping including nuts bolts and washers, PCC works complete with copper strips of suitable size for connecting MCCB complete and comprising of the following:-

(a) MCCB, 4 pole, 100 Amps, 16kA breaking capacity, 415 volts, Fixed Thermal & Fixed Magnetic setting | Ics = 75% of Icu - 01 No. (As Incomer from FPB) (b) MCB, TP, 63 Amp with ultimate breaking capacity Icu-10kA at 415 Volts - 04 No. (3+1 SPARE) (c) MCB, single pole, 40 Amp with ultimate breaking capacity Icu-10kA at 240 Volts - 02 No. (d) Digital Ammeter 0 to 100 Amps & 3 Nos of CT's, Class 1.0, 10 VA -1 Set (e) Digital Voltmeter 0-500 V with 7 position.& 2A HRC fuses/ MCB'S- 1set (f) LED phase indication lamps R,Y,B for incomer and out going switches.

Supply, fix, test and commissioning of LED street light luminaires, outdoor type 90Watts new generation energy saving and environmental friendly long life made up of pressure die cast aluminium housing with Polycarbonate cover having top opening, separate driver compartment with IP66 protection and impact resistance of IK07 with 10KV Built-in surge protection device roadway luminaire with high power LEDs as light source all as per Havells Cat No.ENDURAPEARLPLUSSL90WLED757PASYTOPCASTHO (or) techno-commercially equivalent of other specified makes including connecting with 4.0 Sqmm aluminium conductor PVC insulated twin core weather proof cable etc, fixed to wall/pole etc., complete all as specified and as directed.

Supply, Fix, connecting, testing and commissioning of Post top LED light fitting 8Watts with 600mm length pole landscape, elegant yet minimalistic design and diffuser at the upper portion, IP65 protection, all as per Cat No.CONEBLS8WLED857PSYMTOPC (0.6 M) of Havells or techno-commercially equivalent of other specified makes including PCC work and PVC Junction box with suitable MCBs and flexible single core PVC Copper wire of size 1.5 Sqmm etc., complete all as specified and as directed.

Supply and fix factory made hot press moulded SMC junction / terminal box of size with internal dimensions of 200 x 140 x 95 mm with hinged door, including provision of 2 way connector 415 Volts made out of polycarbonate or bakelite all as per Cat No KG 9003 of Hensel or techno-commercially equivalent of other specified makes including provision of 1 No MCB of 6 Amps with DIN bar, drilling holes for cable connections, connecting incoming and or out going cables by providing suitable size of cable lugs/glands, fixed on pole by means of clamps made out of MS flat iron of size 25 mm x 3 mm etc., complete all as specified and as directed.

Supply, fabricate and installation of GI pipe bracket made out of medium grade GI tubing of 40mm bore of length 1.20metre bent to shape by hot forgoing after filling of sand and fixed on pole / wall with 2 Nos of MS clamps made out 40 x 4mm Flat Iron including bolts, nuts and washers etc., complete all as specified and as directed.

COOLING APPLIANCES AND DESERT COOLER

Supply and fix voltage stabilizers for automatic operation single phase naturally air cooled indoor type and design for input variation between 170 volts to 250 volts with out put voltage stabilizer at 230 volts with accuracy of ± 2.5% and of capacity 1.0 KVA complete all as specified and as directed.

Supply, install, testing and commissioning of Refrigerator, electric driven, single phase, 230 volt AC, 50 Hz, Frost free, Double door, Energy Efficient BEE 3 Star rated of capacity 310/311 litres of LG Model M322RPZL or techno commercially equivalent of other specified makes complete all as specified and as directed.

Supply, install, testing and commissioning of Desert cooler Plastic / PVC body electric driven (single phase), 230 Volt, AC, 50 Hz, having nominal air flow capacity of 3500 Cum per hour, tank capacity not less than 55 litre, collapsible louvers to prevent dust and insects, ice chamber, 3 speed control fan of size 406mm with motor 1350 RPM, Auto fill system, water level indicator and thermal overload protector all as per Cat No.CHRACAWE220 of Havells or techno commercially equivalent of other specified makes complete all as specified and as directed.

FIRE FIGHTING SYSTEMS

Design, Supply and fix Steel sheet enclosure, weather proof , dust proof suitable for monoblock booster pump set made out of Mild steel sheet 3.0 mm thick dust proof, duly treated through 7 tank pre treatment process and painted with epoxy powder coated mat finish of tint as approved by GE etc., complete all as specified and as directed.

Supply and Fix Fire extinguisher CO2, light weight squeeze grip type, 3kg capacity confirming to IS:15683 etc., complete all as specified and as directed.

Supply and Fix Fire Dry chemical powder (ABC powder) type, 6kg capacity confirming to IS:15683 etc., complete all as specified and as directed.

Supply and Fix Fire Water (Stored pressure type) 9 litres capacity confirming to IS:15683 etc., complete all as specified and as directed.

R. Wadhumal and Sons

Sri Raghava Constructions Ltd

Sukhdevraj Sharma Engineers & Contractors Pvt Ltd

VERMA BROTHERS

Phoenix Infra

Dwarka Pershad Radhey Ramanlal

C R R CONSTRUCTIONS