Special Repair/Renovation of Sub Health Centre at village Sandholi in District Kurukshetra under health Wellness Centre Scheme) (Excluding EI)

Amount

Earth work in excavation in foundations, trenches etc. in all kind of soils, not exceeding 2 meters depth including dressing of bottom and sides of trenches, staking the excavated soil clear from the edge of excavation and subsequent filling around masonary, in 15cm layers with compaction, including disposal of all surplus soil, as directed with in a lead of 30 mtrs. (HSR 6.6)

Dismantling brick work, tile masonry or tile lining & tile tracing. (b) In Cement (HSR 8.5 (b)

Stripping and stacking slates or tiles of a roof (HSR 8.10)

Removing doors & windows (wood & steel ) with chowkats by making recesses in the walls (HSR 8.18 (a) Doors )

Removing doors & windows (wood & steel ) with chowkats by making recesses in the walls (HSR 8.18 (b) Windows

Dismantling cement conglomerate/ terrazzo floors 25 mm to 50 mm thick i/c concrete base (HSR 8.26 )

Scraping White & Colour wash (HSR 8.32 (a) )

Scraping Cement plaster (HSR 8.32 (c) )

Cement concrete 1:4:8 with stone aggregate 20 mm nominal size in foundation and plinth (HSR 10.38)

Cement concrete 1:1.1/2:3 with stone aggregate 20 mm nominal size in foundation and plinth (HSR 10.42)

Cement concrete 1:1.5:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel einforcement, but including centring and shuttering, laid in position complete in all respects. (HSR 10.82 +10.95(a).

First class brick work laid in cement sand mortar 1:3 in foundation and plinth (HSR 11.5)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm, laid over 87.50 mm mud filling, on a layer of 25 mm mud plaster and an other layer of mud mortar for laying the tiles including two coats of bitumen laid hot at 1.65 kg per sqm on top of RCC slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Providing & Fixing 100 mm PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (a) 100 mm dia PVC pipe 6 kg. pressure. (Make Supreme, Phinolex, Prince or equvalent)(HSR-13.89 (a))

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, BELL, JOHNSONS.& RAK AND SIMPOLO. (HSR 14.89)

Pdg & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, BELL, JOHNSONS.& RAK AND SIMPOLO. (HSR 14.91)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92) b) Size of ceramic Glazed tiles 300 X 450mm

Plastering on walls 12 mm thick cement plaster 1:3 (HSR 15.4)

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.10)

Applying pink primer or aluminum priming coat on wood work including preparation of surface, knotting and stopping etc. (HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or matallic or plastered or concrete urfaces to give an even shadeas per HSR 16.3.

Preparation of plastered or concrete surface for painting, including sand papering the surface, applying one coat of linseed oil and filling with approved quality filler, consisting of white lead, linseed oil, varnish and chalk mitti including finishing surface to the required finish, complete. (HSR 16.24)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Distempering with washable oil bound distemper (of approved manufacture ) two coats over one priming coats on new work. (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint (b) 1st quality (HSR 16.79 (b)

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete (JK/ Birla make) (HSR 16.81)

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ,chikrassy and chaplash,etc.,(non-coniferous timber other than teak,conforming to I.S.specification No.1003,kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges,screws,chocks/cleats,stops,nails etc., complete,fixed in position (excluding the cost of any fittings,other than specified above,but including labour for fixing the same in position). (HSR 17.90 (b) 35 mm thick )

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash,etc.,(non-coniferous timber other teak, conforming to I.S.specification No.1003, kiln-seasoned),with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail, and wire gauze of 140G or 120G designation including cost of iron hinges, screws,chocks/cleats,stops nail etc.,complete fixed in position (excluding the cost of any fitings,other than specified above,but including labour for fixing the same in position)- (style and rails of windows shutter shall be 75 mm wide) (ii) 35mm thick (HSR-17.92(ii) ) - Note

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic resin,hot- pressesd, conforming to I.S.2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges.) (iii) 35 mm thick. (HSR 17.93 (a) (iii)

Factory –manufactured panelled door shutters,of teak wood,kiln-seasoned, as per I.S.specification no.401, with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 12 mm thick veneered,particle board, or plywood of B.W.R.grade hot-pressed including the cost of iron hinges,screws,chocks/cleats,stops and nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above but including labour for fixing the same in position). (a) Panel of decorative plywood, one side teak faced, and other side commercial faced, 35 mm thick. (HSR 17.94 (a) (ii)

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12 )

Pressed steel sheet frames (chowkats) , consisting of 2 mm thick steel sheet of the specified section, including iron lugs (Holdfast), iron hinges, confirming to PWD specifications etc. complete. (HSR 18.34 ) (a) Door and window frame of size 89 mm x 50 mm with 40 mm wide single rebate )

Pressed steel sheet frames (chowkats) , consisting of 2 mm thick steel of the specified section, including iron lugs(c) door and window frame size 127 mm x 50 mm with 40 mm wide double rebate (HSR 18.34 (c ) )

Providing & fixing in postion best make ( to the approval of the Engineer-In-Chief). Indian type Orissa or orya water closet suite for sinking into floor, with raised foot treads complete with 100 H.C.I. 'P' Trap with or without vent as required and all other necessary fittings (HSR 30.2)(b) (i)Size 630 mm

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT, SYPHONIC TYPE, consisting of- VITREOUS CHINA WARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). One Piece SEAT AND LIDIN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers,(to the approval of the Engineer-in-charge). COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (b) Double trap syphonic (ii) Single Color. [HSR 30.5 (b) (ii)].

EXTRA OVER item nos. 30.1 TO 30.4 AND 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY VITREOUS CHINA HIGH LEVEL CISTERN COMPLETE with internal brass fittings instead of 12.5 liters capacity high level C.I. eistern complete (as approved by the Engineer-in-charge). ( HSR 30.8) (i) White

EXTRA OVER Item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15LITRES CAPACITY C.I. LOW DOWN CISTERN flush bend and all other necessary fittings instead of 12.5 litres capacity high level C.I. flushing cistern with flush pipe complete (as required by the Engineer-in-charge). ( HSR 30.9)

EXTRA OVER Item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY C.I. LOW DOWN CISTERN flush bend and all other necessary fittings instead of 12.5 litres capacity high level C.I. high level flushing cistern with flush pipe IN WHITE ENAMEL SPRAY PAINT after making smooth the C.I. surface by rubbing, scrapping etc., complete (HSR 30.10)

EXTRA OVER Item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY C.I. LOW LEVEL CISTERN complete with flush bend and all other necessary fittings instead of C.I. high level cistern complete with flush bend and all other necessary fittings IN WHITE STOVE ENAMEL PAINT. ( HSR 30.11)

EXTRA OVER Item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY LOW LEVEL VITREOUS CHINA WARECISTERN complete with flush bend all other necessary fittings instead of C.I. high level cistern complete with fittings. (HSR 30.12) (i)

EXTRA OVER item nos.30.3 to 30.6 FOR PrOVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow black or white plastic seat and lid. HSR 30.13 (i) White

Providing and fixing in position best Indian make (Ordinary) lavatory suites consisting of Lavatory in vitreous chinaware size as given below ( to the approval of the Engineer-in-Charge) including China plug for tap hole where necessary R.S. or C.I. brackets for building into wall including painting; 32mm C.P. Brass waste with C.P. brass chain and rubber plug. 15mm C.P. Brass screw down pillar tap with jamnuts or couplings best design(as approved by Engineer-In-Charge) All fittings best Indian make and to the approval of the Engineer-in-Charge. All fittings best Indian make and to the approval of the Engineer-in-Charge. All brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fitting etc white, (iv) Size 550mm x 400mm with one no. tab (HSR- 30.41 (a) (iv)

PROVIDING AND FIXING IN POSITION 32 MM DIA G.I. WASTE PIPE EMBEDDED IN WALL or lead waste pipe (weighing 3.47 kg. per metre and 2.8 mm thick) upto floor Level including cost of wipped solder joint etc., complete (as required by the Engineer-in-charge). (HSR 30.48).

Providing and fixing in position best quality stainless steel sinks with 600mm x 450mm x 200mm complete filling as per site requirement (HSR 30.53.(a)

Providing and fixing in position best indian make towel rails fixed in with rawls lugs embedded in walls with C.P. brass screws,Complete in all respect including cutting & making good the walls etc. (a) 25mm dia C.P. Brass Adjustable (ii) 600mm long (HSR 30.68 (a) (ii)

PROVIDING AND FIXING IN POSITION GLASS SHELF FIXED IN WITH RAWAL PLUGS WITH C.P.BRASS SCREWS COMPLETE INCLUDING CUTTING AND MAKING GOODS THE WALLS ETC. HSR 30.69 (b) WITH ALUMINIUM BRACKETS AND GUARD RAIL

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making goods the walls etc. (a) C.P. Brass (i) Soap dish Large. [HSR 30.70 (a) (i)].

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75]. (a) Bib cock long body.

Providing & fixing in position C.P. brass stop cock (as approved by the engineer-in-charge). (a) 15 mm Stop cock. (ii) Concealed stop cock with flange. [HSR 30.76 (a) (ii)].

Providing and fixing in position automatic brass ball valves in tanks. (b) With Plastic Ball (ii) 20 mm internal diameter. [HSR 30.110 (b) (ii)].

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flages for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. [HSR 30.119]. 1000 Ltrs. Capacity Water Tank

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : (DSR 18.11). 18.11.1 15 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. Wheel of approved quality (Screwed end). (DSR 18.17) 18.17.1A 20 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New Work). (DSR 18.46) 18.46.1 15 mm nominal bore

Recovery of Items:- Good Tiles, Reserve price @ Rs. 5/- Each

Tiles Bats, Reserve price @ Rs. 500/- Cum

Door, Reserve price @ Rs. 500/- Each

Windows, Reserve price @ Rs. 300/- Each

The Maanya Cooperative Labour and Const society Ltd

The Pardeep Singhmar Cooprative Labour and const society L