UPGRADATION OF CLASSROOM AT CME PUNE

Amount

Demolition of cement concrete (un-reinforced) in roof/floors other than ground level beam, stair case, landing, chajjas and similar items including water proofing treatment in any layers and removal of debris to distance exceeding 250m and not exceeding 500m from the site complete all as specified and directed.

M&L for 40 mm thick , PCC 1:2:4 (Type B0 using 20 mm gdd agg) as in levelling course to match the undulations of roof and in in coping , roof kerbs, fins including benching etc complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premisescomplete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wall finishes in CM 1:6.

M & L Virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete as directd.

M & L Virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete as directd.

M& L Fof rendering 10mm thick cement mortar in 1:4 as in backing coat complete all as specified and directed

M & L for one coat of synthetic enamel paint over wooden surfaces including preparation of old surfaces over 10cm width or girth all as specified and directed

Demolition of brick or stone/boulder masonary , built in cement mortar including all quoins, aarches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L precast solid block masonry of block 1:3:6 type C-1 wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surface etc including raking out joints, hacking for key scrubbing down with water all as specified and directed.

M&L rendering 5mm thick on concrete surfaces in CM 1:3 on ceiling, finished even and smooth with sagol all as specified and directed.

M&L for preparation of newly plastered surfaces ceiling and applying complete ceiling with 3mm POP/Birla putty and making smooth surface and applying three coats of white wash over a coat of POP/Birla putty all as specified and directed.

M&L rendering 15mm thick on stone masonary surfaces in CM 1:6 finished even and smooth with sagol over and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying complete wall with 3 mm POP/Birla putty and making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed by Engineer-in-Charge.

M&L 15mm thick plastering on concrete surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of plastered or unplastered old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke spots, moulds, moss effloerent salts and treading oil and greasy spots and applyuing one coat of white (lime) wash complete all as spec ified and directed by Engineer-in-Charge

All as specified in Item No 17 above but applying one coat of white wash on ceiling.

All as specified in Item No 17 above but applying 3mm thick Birla wall putty over plastered and other surfaces

M & L Priming over ( plastered / unplastered / surface where 3mm wall care putty applied in item no 19 ) and other surfaces with alkali resistant priming paint

M & L for complete scraping down of old decorative surface of walls with steel wire brushes of smoke spots, moulds, moss efflorecent salts and applying two coats of Oil bound distemper all as specified and directed by Engineer-in-Charge.

M & L for painting one coat synthetic enamel paint on steel surface including preparation of old surface of any description , over 10 cm width or girth not otherwise described all as specified and directed

S&F aluminium colour powder coated anodised door and shutter single or double leaf glazed/pre laminated board exterior quality partly glazed//pre laminated board exterior quality party glazed panels fabricated including aluminium anodised beading rubber and packing materials and shall be drilling in existing wall and thrust bolt suitable size complete comprising the following:- (a) Aluminium colour anidised door frame section 101.60x44.45x1.93 mm fixed as per spd (b) Aluminium colour anodised vertical section in shutter 85x44.45x2 mm as per spd. (c) Aluminium colour anodised Top & style shutter section 95.25x44.45x2.00 mm as per spd. (d) Aluminium colour anodised handle 02 Nos in each shutter 200 mm long as spd. (e) Aluminium colour anodised middle lock rail/bottom rail section 150x44.2.65mm cat No.20002.Make-Jindal (f) Floor spring Make-Sandhu, (g) Six lever mortice lock brass Make : Godrej/Classic on in each door (h) 12 mm thick particlular board (pre laminated both face) exterior grade ISI Marked (j) Tinted glass/Plain glass(Colour) 5mm thick Make : Saint gobain midgaurd (k) Floor spring , Make Sandu Note : If ground requirement for full glass or full Panel contractor should provide as per direction of Engr-in-Charge.

Supply and installation of techno Acoustic Pannels 10 mm thick, on plywood surfaces with keeping 1 '' gap in between plywood and existing wall , GI framing with section 1'' x1'/2' x2" to be provided inside plywood area and placing rock wool ( 50 kg - 50 density ) inside framing for better performance if reqd for wall panelling . Finally acoustic panels will be pasted on plywood surfaces using special adhesive as per approved shade . ( Panel size -1220 mm x 2440mm x 10 mm thick ) with laser cut / V" groove design / printed design panels in any colour shade with extra infill materail rock wool 50 Kg - 50 mm thk.

Taking down carefully copper/aluminium point wiring (light, fan,bell, socket or power) complete, including fixture and fittings such as switches, Ceiling rose, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc credit for above items should be made as per conditions separately.

Taking down ceiling fans any type/sweep 230 V AC and refixing after cleaning and making connection complete.

Material & labour for point wiring for light/fan/bell with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi stranded, FRLS PVC insulated, unsheathed copper conductor cable in and including PVC concealed conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories / fittings, brass screws, washers etc, modular sunk zinc coated pressed steel terminal boxes including all cutting holes in or through walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed.

All as per item No. 27 above but for one multipin 5 amps socket outlet on same board with other switch complee all as specifed and directed.

All as per item No. 27 above but for one multipin 5 amps socket outlet on independent board complee all as specifed and directed.

All as per item No. 27 above but with 2.5 sqmm cable and 2.5 sqmm for earth continuity for multipin 15 amps socket outlet flush type on independent board complee all as specifed and directed.

S & F in replacement ceiling rose, 3 phase PVC/polycarbonate isolated body, surface bakelite 65 x 50 mm, 3 terminal incl PVC square block complee all as specifed and directed.

S&F in replacement switch Modular, one way 6 amps, 1 module with suitable plate and cover complete all as specified and directed.

S&F in replacement switch modular one way 16 amps, 1 module with suitable plate and cover complete all as specificed and directed

S&F in replacement socket modular 6A, 2/3 pin combined 2 module with suitable plate and cover complete all as specified and directed

S&F in replacement socket modular 6A/16A, 2/3 pin combined 2 module with suitable plate and cover complete all as specified and directed

S&F surface and wall mounted LED batten(LED tube light fitting 20W) with polycarbonate housing & integrated electronic driver alongwith LED tube 20 watt and 02 No PVC square blocks incl taking down old UNSV fitting.

M&L for sub main wiring with two run of 4 sqmm single core multi stranded PVC insulated and unsheathed copper conductor (red for phase and black for neutral) of grade 1100 volt FRLSH cable in and including concelaed 1100 volt electrical grade PVC conduit of desired colour not less than1.2 mm thick and 25 mm wide & 4 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete all as specified and as directed incl taking down old unserviceable one.

Ditto- all as item No 37 above but with cable size of 6 sq mm

Ditto- all as item No 37 above but with cable size of 10 sq mm

S&F in replacement enclosure, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps, 240 volt incl taking down old UNSV one.

S&F in replacement MCB distribution board Double door SPN 240 volts 8 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls etc incl taking down old unserviceable one.

S & F in replacement MCB SP 6 to 32 Amps, 230 V AC incl taking down old unserviceable one.

S & F in replacement MCB SPN 63 Amps, 230 V, AC incl taking down old unserviceable one.

S&F LED Serene Surface Mounting 1feet x 4 feet,CRCA housing 60W, white powder coated, with polymer diffuser complete with accessories, suitable for surface mounting applications of model SZRSBMX060

Aakar Construction

Mukund Engineers and Contractors