82584 SPECIAL REPAIRS TO SENIOR SAILORS INLIVING BLOCK(BLDG NO. P-04) AT KALPAKKAM UNDER AGE(I) NAVY CHENNAI

Amount

SCHEDULE 'A' PART-I [ B/R WORKS]

M&L for Demolition cement concrete (unreinforced) in ground floors and paving n.exc 15cm thick (below & above ground level) complete all as specified and directed by Engineer-in-Charge.

M&L for Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed by Engineer-in-Charge.

M&L for 25mm thick PCC 1:2:4 type B0 (12.5mm graded stone aggregate) levelling course complete all as specified and directed by Engineer-in-Charge.

M & L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces with cement plaster 1:3 with WPC @ 2% by weight of cement (Note : Water proofing compound will be measured and paid separately) including finished even and smooth without using extra cement.(for sunken floor ) complete all as specified and directed by Engineer-in-Charge.

M & L for applying epoxy treatment for sunken floor over 15mm thick rendering on fair faces of brick work of concrete surfaces with cement plaster 1:3 with WPC @ 2% by weight of cement (Note: Water proofing compound will be measured and paid separately) Complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:5:10 type, E-2 (using 40mm graded agg) as in mass concrete as in sunken floorcomplete all as specified and directed by Engineer-in-Charge.

M&L for Dismantling of wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises including removing of all the debris to a distance n exc 2 km out side the base at the disposal of the contractor complete all as specified and directed by Engineer-in-Charge.

M&L for screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes complete all as specified and directed by Engineer-in-Charge.

M&L for 10mm thick screed plaster on fair faces of brick work/concrete in CM 1:3 to receive tiles as in dado complete all as specified and directed by Engineer-in-Charge.

S&F Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 18 sqm but not exceeding 0.38 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles 350 x 250mm x7mm/450 X 350 X 7mm thick as in skirting/dados set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer-in-Charge.

All as per item no 13 here in before but in skirtings complete all as specified and directed by Engineer-in-Charge.

M & L for Demolition of padding concrete in roofs, any thickness, existing roof treament of any description in any condition including removing top surface and removing all the debries Complete all as specified

M & L for Dismatling roof treament on verticle surfaces in roofs parapet walls any thickness, existing roof treament of any description in any condition including removing top surface and removing all the debries complete all as specified and directed by Engineer-in-Charge.

M & L for Brushing neat cement slurry with 3 Kg/Sqm over a cleaned roof surface complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:3:6 type C1 (using 20 mm graded agg) as in padding concrete using water proofing compound @ 5% by weight to maintain required slope including coving to junctions of parapet and roofs complete all as specified and directed by Engineer-in-Charge.

M & L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed by Engineer-in-Charge.

M&L for 5mm thick cement screed in cement mortar 1:4 with water proofing compound at the rate of 2% by weight of cement to have a smooth surface for laying of water proofing membrane complete all as specified and directed by Engineer-in-Charge.

M&L for APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) laid on primed surfaces with 0.40 liter/sqm of bituminious primer, by forced application complete in roof surfaces and on verticle surfaces, complete all as specified and directed by Engineer-in-Charge.

M & L for Applying evenly over and below the membrane a tackcoat of industrial bitumen 85/25 at the rate of 1.2 Kg per Sq.m including cleaning surface over and below the membrane complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls In the same manner. over a coat of 15mm thick screed bed in CM 1:6.complete all as specified and directed by Engineer-in-Charge.

Taking down chowkat or frame with shutters (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each(without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Supply & fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm, but wood grain printed PVC sheet used instead of Plain colour PVC sheet & edge reinforced with M.S. Square tube will be painted to match with printed sheet complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site but 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face complete all as specified and directed by Engineer-in-Charge.

S & F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including 6mm thick teak wood lipping all around the shutter complete all as specified and directed by Engineer-in-Charge.

M&L 35mm thick 2nd class hard wood plain framed panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces.The size of rail and stile as per IS:1003 (Part1),kiln seasoned and chemically pressure treated, complete all as specified and directed by Engineer-in-Charge.

M & L for fixing Plain fillets.Exc 13 & n.Exc 25 SqCm square, rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified and directed by Engineer-in-Charge.

S & F 30 mm thick second class hard made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars) chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately).

S&F sheet glass ordinary quality 4 mm thick, in squares n exc. 0.5 sqm each panel complete all as specified and directed by Engineer-in-Charge.

Supply and fix aluminum anodized grill, 10 mm rod/plate, square, rectangular, circular or similar type of shape, aperture as approved, fixed with `H’ or `F’ channel 38 mm x 12 mm x 1.30 mm (Sec No. 8778), aluminium frame with grill shall be powder coated not less than 50 micron all as specified and as directed. Make: DECOGRILLE Grill type DG 916 or equivalent Complete all as specified and directed by Engineer-in-Charge.

S & F Aluminium alloy wire cloth, 0.45 mm dia of wire and average width of aperture 1.40 mm and fixed with upvc beading complete all as specified and directed by Engineer-in-Charge.

S & F Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engineer-in-Charge.

S&F sheet glass ordinary quality 4 mm thick, in squares n exc. 0.5 sqm each panel complete all as specified and directed by Engineer-in-Charge.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm hinges extruded aluminium alloy with galvanised mild steel pin anodized and fixed type C-21 complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm size aluminium handle, cast type, anodised complete all as specified and directed by Engineer-in-Charge.

S&F 100mm size aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm hinges extruded aluminium alloy with galvanised mild steel pin anodized and fixed type C-21 complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm size aluminium handle, cast type, anodised complete all as specified and directed by Engineer-in-Charge.

S&F 150mm size aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 200mm size aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 300mm long Aluminium, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded section complete all as specified and directed by Engineer-in-Charge.

S & F 150 mm door stopper of aluminium alloy body, with rubber bush complete all as specified and directed by Engineer-in-Charge.

S & F Mild steel Angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps, plain angle cleats for securing purlins and similar small articles confirming to Fe 410-O 0r Fe 310-O complete all as specified and directed by Engineer-in-Charge.

M&L Providing PCC Type B1 1:2:4 (20mm graded aggregate) in as in hold fast fixing complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china squating pan "Orissa" patern size 580 x 440mm white with 'P' or 'S' trap front or back inlet with integral foot rest (excluding flushing cistern and flush pipe), squating pan including trap set and concretingconnection to trap and flushing pipe, anit syphonic pipe etc complete incl making good to floor complete all as specified and directed by Engineer-in-Charge.

S&F Vitreous china wash down water closet pan ( pedestal pattern ),white ( excluding fixing bolts, flushing cistern and flush pipe ) but including seat cover and connection to drain or outgoing pipe and to flush pipe,antisyphonage pipe etc complete all as specified and directed by Engineer-in-Charge.

S & F PVC valve less flushing cistern low level 10 litres capacity with syphonic action type with inlet ball valves, float and handle and connections to pipes and fixing of chain and pull (or) lever including brackets and 32mm dia PVC flush pipe of 60cm long complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous china, wash hand basin white flat back size 550 x 400mm white complete waste, chain and pug and precelian stopper including bracket.Complete all as specified

S & F 32 mm bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipes or connections including necessary packing union and cap complete all as specified and directed by Engineer-in-Charge.

Supply and Fix pillar tap 15mm dia, cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shank and fly nut screwed for iron pipe & fixed complete all as specified and directed by Engineer-in-Charge.

Supply and Fix 32mm waste fittings brass of chromium plated for wash basin etc, with long screwed shanks and fly nut, flange end bedded in red lead cement and others and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair bib taps of cast copper alloy screwed down high pressure with crutch or butterfly handle screwed for iron pipes of 15mm bore complete all as specified and directed by Engineer-in-Charge.

S&F in repair Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed by Engineer-in-Charge. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer-in-Charge.

S & F PVC (SWR) Floor trap of 75 mm outlet plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F in repair Angle valves fancy type,chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe of 15mm bore complete all as specified and as directed..

S&F Vitreous china urinal partition white of size 310x700 mm complete all as specified and directed by Engineer-in-Charge.

S&F soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge.

S&F in repair aluminium anodised tubular rail 20mm dia D type 60cm long between flanges including per pair brackets for each towel rail complete all as specified and directed by Engineer-in-Charge.

S&F in repair aluminium hat and coat hooks pegs solid body 125mm to 175mm long complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15mm bore concealled stop valves cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge.

S&F for 32 mm bore low density polythylene pipes (HDPE) of pressure rating 6Kgf/cm2 fixed compete to in walls, floors,ceilings etc Complete all as specified and directed by Engineer-in-Charge.

S&F in repair Brass chromium plated shower rose 125mm size, with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

S & F Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engineer-in-Charge.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

M & L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M & L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M & L for Rendering 15mm thick with CM 1:4 on fair faces of Brick masonry surfaces finished fair and even complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick walls including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed by Engineer-in-Charge.

M & L Rendering for 10mm thick in cement mortar (1:6) on other than fair faces of internal bricks or concrete surfaces finished even and smooth with using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in two layers 10 mm thick backing coat in cm 1:6 and 5mm thick finishing coat in cm 1:4 . mixed with water proofing @ 2% by weight of cement with rough cast plasters finshes complete all as specified and directed by Engineer-in-Charge. (Note :- WPC will be measured separately).

M & L Rendering 5mm thick on ceiling in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in two layers 10 mm thick backing coat in cm 1:6 and 5mm thick finishing coat in cm 1:4 . mixed with water proofing @ 2% by weight of cement finished even and fair complete all as specified and directed by Engineer-in-Charge. (Note :- WPC will be measured separately).

M&L for rendering 5 mm thick on fair faces of brick work or concrete surfaces rendering in cement mortar 1:3 with WPC including finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for internal surfaces of walls /Slabs shall be plastered with 5mm Thick in Cm 1:3 with WPC Finished even and smooth using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L for applying Epoxy stearats coating waterseal of M/S Krishna conchem covering 3 Sqm /Lt per each coat applied in 3 coats .This shall be carried out by Providing and applying Epoxy stearats coating waterseal with an interval of Minimum 6 Hours between the Coats complete all as specified and directed by Engineer-in-Charge.

M&L for preparing newly plastered surfaces by vacuum based sanding machine and applying two coats of distemper oil emulsion over coat of primer on surfaces of walls including 3mm th wall care putty on walls using mechanical tool/auto roller complete all as per manufacturer instruction complete all as specified and directed by Engineer-in-Charge. Note: All work shall be carried out by approved applicator of paint manufacturer only. The same shall be approved before carrying out the work from AGE(I). Contractor should submit Auth applicator certificate before execution of work.

M&L preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

Material & Labour prepartion of new plastered surface by vacuum based sanding machine and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) using mechanical tool/auto roller complete all as per manufacturer instruction and including necessary scaffoldings complete all as specified and directed by Engineer-in-Charge. Note: All work shall be carried out by approved applicator of paint manufacturer only. The same shall be approved before carrying out the work from AGE(I). Contractor should submit Auth applicator certificate before execution of work.

M & L Preparing newly plastered surfaces of celings and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

Material & Labour complete removal & prepartion of existing treatment by vacuum based sanding machine and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) using mechanical tool/auto roller complete all as per manufacturer instruction and including necessary scaffoldings complete all as specified and directed by Engineer-in-Charge. Note: All work shall be carried out by approved applicator of paint manufacturer only. The same shall be approved before carrying out the work from AGE(I). Contractor should submit Auth applicator certificate before execution of work.

M & L complete removal of existing treatment & preparation on walls by vacuum based sanding machine and applying two coat of distemper oil emulsion over a coat of primer on surfaces of walls including 3mm th wall care putty on wallsusing mechanical tool/auto roller complete all as per manufacturer instruction complete all as specified and directed by Engineer-in-Charge. Note: All work shall be carried out by approved applicator of paint manufacturer only. The same shall be approved before carrying out the work from AGE(I). Contractor should submit Auth applicator certificate before execution of work.

M & L Preparing old plastered surfaces of celings and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

M & L Preparing old plastered surfaces of walls and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

M & L Preparation of new or previously untreated wooden surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of Synthetic Enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation old previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel Paint complete all as specified and directed by Engineer-in-Charge.

M & L for Taking up or down steel tubing 20mm dia bore and connection including cleaning for refixing or removal complete all as specified and directed by Engineer-in-Charge.

M & L for Taking up or down steel tubing 25mm dia bore and connection including cleaning for refixing or removal Complete all as specified

M & L for Taking up or down steel tubing 40mm dia bore and connection including cleaning for refixing or removal complete all as specified and directed by Engineer-in-Charge.

Supplying and laying of 20 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engineer-in-Charge.

Supplying and laying of 25 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engineer-in-Charge.

Supplying and laying of 40 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engineer-in-Charge.

Material and labour for Cutting chases, pinning in , for concealed water tubing on brick or stone walls, making good to facing where required and pointing in cement mortar 1:3, not exc 10 cm girth complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Brass Elbow (3/4 X ½)for 20mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Brass Elbow for 25 mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Brass Elbow for 40 mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Brass Tee for 20 mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Brass Tee for 25 mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Brass Tee for 40 mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Male Brass Threaded Adaptor (MTA/ MBTA) for 40 mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Female Brass Threaded Adaptor (FTA/ FBTA) for 40 mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Union for 25 mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Ball valve of 40mm dia complete all as specified and directed by Engineer-in-Charge.

Taking down rain water pipe and sewage pipe of any size of pattern including all fittings, heads, shoes, bends etc complete all as specified and directed by Engineer-in-Charge.

S&F for 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring jointslaid in trenches or floors complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm dia bore PVC (SWR) branch piece, single (Single 'Y') equal or unequal complete all as specified and directed by Engineer-in-Charge.

S&F for 110mm dia bore PVC (SWR) junction single, (Single 'T') equal or unequal complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm dia bore PVC (SWR) bends any redius complete all as specified and directed by Engineer-in-Charge.

S&F for 110mm dia bore PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

S&F for 110mm dia bore PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm dia bore PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

M & L for Surface Excavation not exceeding 30 Cm deep and averaging 15 Cm deep and getting out in Soft/ Loose soil complete all as specified and directed by Engineer-in-Charge.

M&L hardcore of gauge exc 63mm deposited ,spread &levelled in layers n exc 15cm thick,watered and rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick Cement concrete type C2, 1:2:4(using 20 mm graded stone aggregate) in sub base of flooring/ hard standing/pavings/plinth protections, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L treating the soil under plinth protection at the rate of 5.0 ltr of emulsion per sqm of surface area complete all as specified and directed by Engineer-in-Charge.

M&L treating the soil along with external perimeter of building at the rate of 2.25. ltr of emulsion per mtr of the perimeter walls complete all as specified and directed by Engineer-in-Charge.

M & L for Breaking the termite mounds, making holes with crow bars and pouring antitermite chemical emulsion at the rate of 4 litres per cubic metre of mound complete all as specified and directed by Engineer-in-Charge.

Material and Labour treating the soil along the external wall below concrete using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc complete all as specified and directed by Engineer-in-Charge.

M&L for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm part including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors Complete all as specified

M&L for providing ATT by injecting at point of contact of wood work by chemical emulsion (oil or kerosene based solution)@ 0.5 lit/ hole by driling 6mm dia hols at downward angle of 45 degrees at 150 mm centre to centte and sealing the same Complete all as specified

Demolition of stone slabs and tiles of any description or any thickness in floors, skirtings, risers etc laid ,bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.

S & F Mild Steel Gate and shutter, hooks and eyes 100 mm Complete all as specified

S & F Mild Steel Gate and shutter, hooks and eyes 150 mm Complete all as specified

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel over a coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation old previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel Paint Complete all as specified

S & F in repairs Gun metal 40 mm dia of pipe globe or gate valve with Iron wheel head, screwed both end for Iron pipe one fixed complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S & F curtain steel pipe for doors and windows of 25 mm dia complete all as specified and directed by Engineer-in-Charge.

S & F 25 mm of Stainless Steel Glossy Matte Series fancy Curtain Bracket including clips complete all as specified and directed by Engineer-in-Charge.

M & L for demolistion of Concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed by Engineer-in-Charge.

M & L for laying reinforced cement concrete Type B0 1:2:4 (12.5mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed by Engineer-in-Charge.

M & L for laying reinforced cement concrete Type B0 1:2:4 (12.5mm graded aggregate) in chajjas and like etc complete all as specified and directed by Engineer-in-Charge.

M & L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed by Engineer-in-Charge.

M & L for laying Mild steel bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips with the existing bars using the rebar injection chemical complete all as specified and directed by Engineer-in-Charge. (Note: The rebar injection chemical will be measured & paid separately)

M& L for making of 1 no holes size of 8mm dia and depth of 200 mm for chajjas and canopy for fixing of TMT bars by applying the HILti Hilt RE 500 V3 chemical as per Manufacturer instruction & complete all as directed by Engineer-in-Charge. (Note: The TMT bar will be measured & paid separately)

M&L for preparation of new or previously untreated wooden surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of Synthetic Enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound.Complete all as specified complete all as specified and directed by Engineer-in-Charge.

Removing of debries any description obtained from demolition beyond the lead included in the rates including loading unloading to a distance exceeding 1.5Km and not exceeding 2.00 KM out side defence land.Complete all as specified and directed by Engineer-in-Charge.

S & F for rotational moulded polyethylene water storage tank of 1000 ltrs capacity (cylindrical verftical with closed top) including all fittings i.e tank nipple, of 25mm dia Ball brass valves, high pressure, with polythene float and flynut etc hoisted and fixed in position complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B0 (12.5mm graded stone aggregate) levelling course complete all as specified and directed by Engineer-in-Charge.

Taking down and refixing of alumium partion of size 2.1 m x 1.5 m in the same pattern in the same loctaion without any change in partition including screws and clips complete all as specified and directed by Engineer-in-Charge.

S & F rectangular Mirror of any size 4mm thick of size 1.5 m x 0.45 m mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engineer-in-Charge.

S & F Heavy duty colour steel wire with 2mm thick dia anti-rust SS wall mounted cloth dryer/Hangers of 6 lines with 150 mm spacing complete all as specified and directed by Engineer-in-Charge.

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48x40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

S & F of 0.90mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed.

S & F of 12mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and as directed complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings as complete all as specified and directed by Engineer-in-Charge.

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

M & L for Granite 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm cement screed in CM 1:6 Complete all as specified and directed by Engineer-in-Charge.

M & L for granite 20 mm thick (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust With admixture of pigment to match with shade of Granite Complete all as specified and directed by Engineer-in-Charge.

Labour for Grooves (square, hollowed or dovetailed), rebate in face work on granite complete all as specified and directed by Engineer-in-Charge.

M & L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, window cills and other similar situations Complete all as specified and directed by Engineer-in-Charge.

S & F 40 mm thick Rectangular Polished GRC Cement Jali with frame all around Exterior or outdoor type in CM 1:6 with no pigment in high quality complete all as specified and directed by Engineer-in-Charge.

M & L for Resecuring by taking down the shutter of any description n exc 1 sq. m each from the frame and Refixing in the same opening complete all as specified and directed by Engineer-in-Charge.

M & L for Resecuring by taking down the shutter of any description exc 1 sq. m and n exc 2 sq. m each from the frame and Refixing in the same opening complete all as specified and directed by Engineer-in-Charge.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engineer-in-Charge.

S & F of 0.80mm thick 304 brushed stainless steel backlight letters colour finished with RF painting with backing of 2mm thick imported acrylic laser cut letter of depth 50mm and height 300mm describing " NARASHIMA BLOCK" including LED 3 Eyes C White/2835 Samsung LED Chip/WP-IP68/1.08Watts & Total LED consumption 271 nos complete all as specified and as directed.

SCHEDULE 'A' PART-II [ E/M WORKS]

Taking down carefully any type point wiring (light, fans, socket etc) complete including battens and fittings such as switch, ceiling rose, light fittings, regulators, socket, etc. and making good disturbed surface of wall/floor, etc. complete all as specified and as directed.

Taking out old/existing MCB DB SPN/TPN complete by disconnecting all as directed.

Taking down old sub main wiring with 2runs/4runs of 4/6/10 sqmm aluminium/copper cables including making good disturbed surface complete all as specified and directed.

Material and labour for point wiring (concealed) on walls and surface on ceiling complete with FRLS PVC insulated unsheathed 1100 Volts grade, conforming to IS-694, 1.5 sq mm (nominal area) multi stranded copper conductor cable drawn though in and including non metallic medium grade rigid PVC conduit heavy grade accessories, ISI marked, 19/20 mm dia including all accessories, concealed in walls by cutting chases using machine and making good the disturbed surface, with and including suitable 1.5 sq mm copper earth continuity wire connected to earth dolly complete for the following complete all as specified and as directed.

(a) One light point controlled by one switch

(b) One Ceiling fan/Exhaust fan point controlled by one switch

(c) One switch socket outlet modular type 3 pin 6 amp on independent board.

(d) One switch socket outlet modular type 3 pin 6 amp on same board.

(e) 3 pin socket outlet 15 amps sockets on independent board with 4sqmm multistranded copper PVC insulated cable complete all as specified and directed.

(f) One light point controlled by two Nos of two way switches.

Remove of Ceiling Fan /Exhaust Fan and Electric Meter from Existing Place and Refixing after Servicing on Same Place all as specified and directed

M&L Modular switch 1 way 10 A, 1 module complete all as specified and directed.

M&L Modular switch 2 way 10 A, 1 module complete all as specified and directed.

M&L Modular switch 1 way 16 A, 1 module complete all as specified and directed.

S & F Modular socket 6A - 2/3 pin combined 2 module complete all as specified and directed.

S & F Modular socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S & F Modular fan Regulator,120w step type 2 module complete all as specified and directed.

M&L ceiling rose, 3 terminals PVC / Polycarbonate, isolated body complete all as specified and as directed.

S & F modular white cover plate with frame 1 module complete all as specified and directed.

S & F modular white cover plate with frame 2 module complete all as specified and directed.

S & F modular white cover plate with frame 3 module complete all as specified and directed.

S & F modular white cover plate with frame 4 module complete all as specified and directed.

S & F modular white cover plate with frame 6 module complete all as specified and directed.

S & F modular white cover plate with frame 8 module complete all as specified and directed.

S&F Modular Metal flush box 1/2 Module complete all as specified and directed.

S&F of Modular Metal flush box 3 Module complete all as specified and directed.

S&F of Modular Metal flush box 4 Module complete all as specified and directed.

S&F of Modular Metal flush box 6/8 Module complete all as specified and directed.

Material and labour for sub main wiring (concealed) complete with two single core 4 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 20 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 4 Sqmm FRLS PVC insulated unsheathed stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface all as specified and directed. Note: 3 run of 4 sqmm & one run of PVC conduit shall be measured as single unit

Material and labour for sub main wiring (concealed) complete with two single core 10 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 25 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 10 Sqmm FRLS PVC insulated unsheathed stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface all as specified and directed. Note: 3 run of 10 sqmm & one run of PVC conduit shall be measured as single unit

Material and labour for telephone sockets , modular type (for telephone and data cable) complete all as specified and as directed.

Material and labour for TV sockets, special modular flush type complete all as specified and as directed.

Supply and fix , 20 mm external dia Rigid non -metallic PVC conduit exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth, tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and directed. Note:- For TV & data cable

Supply and fix PVC junction box (1 to 4 way) , 20 mm external dia for TV/Tele wiring complete all as specified and directed.

Supply and fixing of single pole and neutral encloser with a two pin and earth plug and socket complete with one single pole MCB 240V, 20Amps complete all as specified and directed.

Supply and Fix Double Door Vertical TPN Distribution Box 4 way complete in SS enclosure with 200 amps rated busbar complete all as specified and directed.

Supply and Fix MCCBs 415 Volt 100 Amps with 16KA breaking capacity 4 pole complete all as specified and directed.

S&F MCB DB TPN 4 way complete in SS enclosure single door type with 200 amps rated busbar. complete with all as specified and directed by Engr-in-Charge.

Supply and Fix of MCB TPN 415 volts 40-100 Amps with 10KA breaking capacity complete all as specified and directed.

S & F RCBO Four Pole,100mA, 415 volts 63 Amps with Front face indication for earth leakage fault , Over load & Short circuit Protection terminals 35 sq mm terminals Sliding shutters. Complete all as specified and as directed by Engr-in-charge.

Supply and Fix of MCB SP 240 volts 6- 32 Amps with 10KA breaking capacity complete all as specified and directed.

Supply and Fix of MCB SP 240 volts 63 Amps with 10KA breaking capacity complete all as specified and directed.

Supply and Fix LED light fitting 4feet,1x20w,a trendy wall mounted batten,with extruded aluminium housing, with integrated LED driver, etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and Fix LED light fitting 2 feet,1x10w,230v,a trendy wall mounted batten,with extruded aluminium housing, with integrated LED driver, etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and Fix Energy saving new generation 10W LED IP65 bulkhead luminaries with opal diffuser and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450mm sweep with, blades, and frame and louvers complete all as specified and as directed by Engr-in-Charge.

M&L for Cutting the existing wall for fitting coller of 450mm exhaust fan and making good disturbed surfaces inner and outer of wall Complete all as specified and as directed by Engr-in-Charge.

S&F of Angle holder ,PVC /Polycarbonate type With LED bulb 9 Watt all as specified and Directed by Engineer in Charge

M/L for providing earthing complete with copper plate electrode 600 mm x 600 mm x3.15mm thick buried directly in ground earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below normal ground level ,Alternate layers of charcoal) & common salt Crystal and connected to Copper earth strip 20x3mm by means of bolts, nuts, check nuts & washers of copper and connecting to earth dolly all as shown in electrical plate No. 3of SSR Part I of 2009 & testing complete including 40mm dia light grade GI pipe up to 7.5mtr long, excavation in any type of strata, PCC ( 1:3:6 ) type C1 earthing chamber, pre cast slab 50 mm thick in cement concrete ( 1: 2 : 4 ) type B 1 ( reinforced with welded steel wire fabric (XPM) weight not less than 4 Kg / Sqm with frame, test box , including 20 mm bore water pipe medium grade GI Tubing including GI Funnel , wire mesh etc. ( NOTE :- Earth continuity conductor and GI protection pipe beyond 7.5m shall be measured and paid under the respective items ).all as directed by Engineer- in charge.

M/L for earth continuity conductor or copper strip 20x3 mm buried in ground / fixed on wall / drawn in GI pipe, complete all as directed and specified by Engr in Charge.

Taking down Old UNSV XLPE UG Cable Aluminum Conductor any Sizes complete all as specified and directed by Engr-in-Charge

Supply laying & testing cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area of size 4 core 10Sqmm, including all accessories such as screws, clips, plugs, clamps etc, as specified for securing cables to wall etc. Complete all as specified and as directed by Engr-in-Charge.

Supply laying & testing cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area of size 3.5core 185 Sqmm Complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches not exc 1.5 mtr wide and n. exc 1.5 m depth for foundations or laying under ground cable, pipes etc. and getting out in soft/loose soil etc. Complete all as specified and directed by Engr-in-charge.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil. Complete all as specified and directed by Engr-in-Charge.

Removing excavated soil to a distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.50 meter above the starting point complete all as specified and directed.

Supply and fixing High density polyethylene (HDPE) pipes of pressure rating 6kgf/ sq..cm of size 50 mm dia for cable protection laid in trenches complete all as specified and directed

Supply and Laying in trenches for GI pipe Light grade 40 mm dia as for Road Crossing of Cable complete all as specified and directed

Demolition of cement concrete (unreinforced)for passing pipe of any description and in any position not otherwise specially provided for complete all as specified and as directed

M&L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete Type B1 1:2:4 of Using 20mm aggregate complete all as specified and as directed

Supply,Fabricate,Install,Testing and commissioning of indoor type factory made cubical type, dust & vermin proof powder coated LT panel board made out of 2.00 MM MS sheet of size 1.8 m x 1.6 m x .30 mtrs, locking arrangement with double door type,mounting on angle iron frame duly grouted on in and including PCC platform raised at 20 CMS above surrounding ground level , with copper bus bars of suitable size.The LT panel board shall comprising the following. Incoming :- (a) S & F MCCB 4 pole 160 amps with breaking capacity 36 KA , Adjustable type microprocessor release 415 volts AC 50 HZ - 01 Nos Outgoing/Distribution :- (a) S & F MCCBs 4 pole Adjustable type 125 A, 16 KA, thermal release, 415 volts AC 50 HZ - 01 Nos (b) S & F MCCBs 4 pole Adjustable type 100 A, 16 KA, thermal release, 415 volts AC 50 HZ - 04 Nos (c) S & F MCCBs 4 pole Adjustable type 63 A, 16 KA, thermal release, 415 volts AC 50 HZ - 06 Nos (d) S & F MCCB 4 pole 40 amps with breaking capacity 16KA 415 volts AC 50 HZ - 02 (e) Lamp indicators LED type for R,Y,B phases ( set of three Nos) (f) Digital type ammeter 0-300 amps complete with CT 300/5 amps (g) Digital type volt meter 0-500 volts 415 volts AC 50 HZ.

Supplying and laying synthetic Rubber insulated mats 2.5 mm thick for voltage upto 11 KV for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety of sizes 2m x 1m complete all as specified and as directed

V R K CONSTRUCTIONS

S VENKATESAN

lakshmibuilders

kvs constructions

M/s KM Marimuthu Achary

GV Foundations

Kaadosh Real Estates Pvt Ltd