50 Bedded Hospital Beri

Amount

Dismantling Roofing (HSR 8.8) (g) demolishing mud phaska in tile terracing

Scraping (HSR 8.32) (c) cement plaster

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25mm mud mud plaster and an other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Cement concrete 1:2:4 gola 10 cm X 10 cm quadrant along junction of roof with parapet wall finished smooth, where specially specified.(HSR 13.64)

Precast chequered tiles of 20 mm thickness in ordinary grey ceent without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base of floors, treads of steps and landings. (HSR 14.45)

Providing and fixing vitrified tiles of size 600x600mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. (HSR 14.89) Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJA-RIA, SOMANI, ORIENT, JOHNSONS, RAK, SIMPOLOA & OASIS

12 mm thick cement plaster 1:6 (HSR 15.7)

15 mm thick cement plaster 1:6 on the rough side of single or half brick wall (HSR 15.12)

10 mm thick cement plaster 1:4 (HSR 15.52)

Painting two coats excluding priming coat with synthetic enamel paint in all shades of new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 16.3) 1st Quality

Distempering with washable oil bound distemper (of approved manufacture) two coats excluding priming coat on new work. (HSR 16.57)

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on new work, two coats to give and even shade. (HSR 16.61)

Providing two coats of exterior acrylic emulsion paint. (HSR 16.79) (b) Ist Quality

Providing and applying two coat white cement based putty over plastered surface and griding the surface smoothwise sand paper to get an even and smooth finish including cost and carriage of all material, labour charges scaffolding, sundries etc complete in all respect (HSR 16.81)

Factory-manufactured paneled door or glazed window, shutters of commercial hard wood, such as hillock, champ, chikrassy and chaplash, etc., (non-coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln-seasoned), with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete fixed in position ( excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position (HSR 17.90) (b) 35 mm thick

Factory-manufactured wire gauze door and window shutters of commercial hard wood such as hillock, champ, chikrassy and chaplash, etc. (non coniferous timber other teak, conforming to I.S. specification No.1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (steels and rails of windows shutter shall be 75mm wide) (HSR 17.92) (ii) 35mm thick

Factory manufactured solid flush door shutters, with block board core as per I.S. No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II , fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position) (HSR 17.93) (a) Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges (iii) 35 mm thick

Supplying and fixing glass panes including special metal sash putty of approved make (HSR 18.30) (b) Glass panes 4 mm thick upto 40sq. dm area.

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete (HSR 18.34.) (b) Door and window frame of size 76 mm X 38 mm with 35 mm wide single rebate.

(d) Door and window frame of size 114 mm X 50 mm with 35 mm wide double rebate.

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with ilet and outlet pipes, providing over flow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. (HSR 30.119) 500 Ltr.Capacity

1000 Ltr.Capacity

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the wall etc. (DSR 18.10) (18.10.1) 15 mm dia nominal bore

(18.10.2) 20 mm dia nominal bore

(18.10.3) 25 mm dia nominal bore

(18.10.5) 40 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) (DSR 18.17) (18.17.1A) 20 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) (DSR 18.46) (18.46.2) 20 mm nominal bore

Recovery item : Recovery items: The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layers have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under. Brick @ Rs. 4.00 each

Brick Bats @ Rs. 450/- P Cum

The Sat Sahib Coop L C Society Ltd.