E1-2751-2024-ERODE CITY MUNICIPAL CORPORATION -CONSTRUCTION OF NEW LIBRARY BUILDING AT COLLECTOR OFFICE PREMISES IN ERODE.

Amount

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Removing hard rock by wedging, chiseling and trimming to proper shape where blasting is prohibited. etc., complete as per standard specifications

Collection,supply and filling of Well gravel from approved quarry to work site and stocking to the Departmental gauge for premeasurement as directed by the Departmental Engineer, to required depth not more than 15cm depth including cost and Conveyance of gravel to site and all labour charges for filling etc., Complete complying with Standard Specification as per clause MORTH 30 Specification.

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:4:8 (One Cement, Four crushed stone sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

a) Without Strutting

b) Column

c) With Strutting (plain surface)

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

a) Upto Basement

b) Ground floor

c) First floor

d) Second floor

e) Third floor

f) floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

a) Upto Basement

b) Ground floor

c) First floor

d) Second floor

e) Third floor

f) floor

Brick partition walls of 11.50cm thickness using best quality Fly Ash Bricks of size 23 x 11 x 7 cm in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

a) Ground floor

b) First floor

c) Second floor

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Paving the Top of roof with Solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

Solid PVC Door Shutters using 19 Gauge 19mm MSsquare tubes for styles and outer frames. 15mm MSsquare tubes for top, lock and bottom rails. The steeltubes shall be covered with 5mm thick solid PVCSheets. Shutter using 5mm thick solid PVC Sheets forpanelling shall rigidly fixed in position includingnecessary furniture and fittings. The over all size ofstyles shall be 50mm x 30mm. The over all size of toprail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm withsuitable rabate for housing the shutter (As per SOR 24-25 Vol-1 P.no-81 M-0391,M-0393)

Solid panel PVC door with frame

Sliding solid panel PVC door with frame

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Manufacturing, Supplying and Fixing of Stainless Steel Handrails for staircase using 50mm dia 304L Grade Stainless Steelpipe of 1.60mm thick at required locations to a height of900mm from finished floor level welded to 38mm diaStainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediatehorizontal stainless steel pipe of 1.60mm thick in between.The vertical pipe has to be welded to the 100 X 100 X 6mmMS base plate encased in the base concrete. The rate isinclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc.complete (As per SOR 24-25 Vol-1 P.no-98 M-0651)

Manufacturing, Supplying and Fixing of Stainless Steel Handrails for staircase near wet riser using 50mm dia 304L GradeStainless Steel pipe of 1.60mm thick will be provided withtubular supports made of 304L Grade Stainless Steel pipe of25mm dia of 1.60mm thick welded to the railing. Thesupports will be grouted into the wall and provided with93.00mm thick Stainless Steel circular base plate of 304Grade. The rate shall included for grouting into concrete withnecessary supporting arrangements the hand rail in floorpolishing buffing, bonding, cutting, grinding, conveyance,welding charges, electrical charges, etc. complete (As per SOR 24-25 Vol-1 P.no-98 M-0652)

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates ashandle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash andouter frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the ExecutiveEngineer before use on work (As per SOR 24-25 Vol-1 P.no-109 M-0674)

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round theframes. The ventilator should be got approved from the Executive Engineer before use on work (As per SOR 24-25 Vol-1 P.no-109 M-0675)

Flooring with Self Designed Colour Ceramic Tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with printed design colour glazed tiles of size 300 x 200 x 6mm best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position best quality and approved make Indian made colour glazed earthernware wash hand basin of size 550 x 400mm with pedestal with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing in position white glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supplying laying and jointing P.V.C pipes (6Kg/SqCm) andG.I.Pipes of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

75mm dia PVC pipe (As per SOR Vol-1 P.no-146 M-0869)

75mm dia PVC Bend (As per SOR Vol-1 P.no-153 M-1008)

75mm dia PVC Tee (As per SOR Vol-1 P.no-153 M-0996)

110mm dia PVC pipe (As per SOR Vol-1 P.no-146 M-0872)

110mm dia PVC Bend (As per SOR Vol-1 P.no-153 M-1010)

110mm dia PVC Tee (As per SOR Vol-1 P.no-153 M-0998)

SS Heavy Duty Long Body Tap 15mm (As per SOR Vol-1 P.no-89 M-0542)

25mm dia G.M.Gate Valve (As per SOR Vol-1 P.no-87 M-0501)

32MM dia,PVC pipe (As per SOR Vol-1 P.no-147 M-0877)

32MM dia,PVC Elbow (As per SOR Vol-1 P.no-147 M-0889)

32MM dia,PVC Tee (As per SOR Vol-1 P.no-148 M-0901)

25mm dia.PVC pipe (As per SOR Vol-1 P.no-146 M-0876)

25mm dia.PVC Elbow (As per SOR Vol-1 P.no-147 M-0888)

25mm dia.PVC Tee (As per SOR Vol-1 P.no-148 M-0900)

PVC Water tank (As per SOR Vol-1 P.no-89 M-0540)

100mm x 75mm PVC Nahini / Floor Trap with Stainless Steel Grating PWD Data

40mm dia GI Elbow (As per SOR Vol-1 P.no-84 M-0447)

40mm dia GI Union (As per SOR Vol-1 P.no-84 M-0441)

40mm dia GM NRV (As per SOR Vol-II P.no-33 WD-M0619)

40mm dia Clampset (As per SOR Vol-II P.no-32 WD-M0617)

MS Cover plate (As per SOR Vol-II P.no-195 WD-W0737)

40mm dia UPVC pipe heavy (As per SOR Vol-II P.no-7 WD-M0050)

40mm dia UPVC Adopter

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Wiring with 2x1.5sq.mm. PVC insulated SCunsheathed FRLS copper conductor of1100V grade insuitable PVCrigidpipe concealed inwall and ceiling with PVC accessories inflush with wall with3mmthick hylumsheet cover withTWswitch box and 5AFTswitch with continuousearthwireconnection of1.5sq.mm copperwire formaking good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator) (SD-23)

Wiring with 2x1.5sq.mm.PVC insulated SCunsheathed FRLS copper conductor of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with150mmx100mmx113mm TW switchbox with 3mmthick hylemsheet cover for 5A 3 pin noninterlocking wall socket with 5A flushtypeswitch with continuousearthwireconnection of 1.5sq.mm copper wire and making good of the concealed portion with suitable colour for concealed PVC plug point(SD-38)

Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x113mm TW switch box with 3mm thick hylem sheet for 15A 3 pin non inter locking wall socket with 15A flush typeswitch with continuous earthwire connection of 4sq.mm copper wire and making good of the concealed portion with suitable colour for concealed power plug point(SD-40)

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.(SD-439)

supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 600mm down rod with fan clamp with side plates and cross arm of size 450mm (18")(SD-476)

supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .(SD-448)

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mmMS base plate duly welded at the bottom with concreting with construction of masonary pedestal withsuitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylemsheet and supply and fixing of 60W LED street light fitting with LED (Lower end) with 1 metre 32mm dia.GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVCunsheathed copper leads from SMC box to fitting and with painting of suitable colour .(SD-457)

Supply and Laying of 3 1/2 x 25 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(SD-659)

Supplying, fabricating, erecting and fixing Hilux (or) Equivalent Board False Ceiling upto a ceiling height of 4.5m from floor level -Using Perforated Sheets 10mm thick of the following types with G.I. perimeter channel of size 0.55mm tk (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimetre of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws at 610mm centres. Then suspending G.I. Intermediate channel of size 45mm (0.90mm thick with two flanges of 15mm each) from the soffit at 1220mm centres with ceiling angle of 25mmx 10mmx0.50mm thick etc complete as per std specification. (As per SOR Vol-1 P.no-93 M-0619)

Supplying and erecting in position of 250 liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set(c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No.(e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No.& Pressure Gauge - 2 Nos.(f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., LowPressure Switch - 1 No., Level Switch - 1 No. & NecessaryCPVC Pipes and Fittings.The system shall be provide with Two Panel Control Systemwith necessary Stainless Valves and Fittings and Float Controletc. The rate should be inclusive of all civil works, wherevernecessary to install the System in position and intact.(As per SOR Vol-1 P.no-118 M-0721)

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps,fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer (As per SOR Vol-1 P.no-99 M-0658)

Manufacturing,supply and erection of 10 persons passanger gearless lift without macine room car size (1300 x 1350 ) (G+3) made out of SS 304 grade with 1m/sec (As per SOR 23-24 P.no-157 M-2089)

Supply and fixing of 7 segment 8 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 24 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following on wall with earth connection only.(SD-623)

EarthingasperPWDstandardwithanearthelectrodeof2metreClass'B'GIpipeofdianotlessthan32mmcompletewith necessary masonry work (SD-212)

Supply and fixng of TNEB meter board suitable for 3 phase 200A service connection made up of suitable angle ironframe work of size 3 feet x 2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered withhylem sheet of size 3 feet x 2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixingof 3 Nos. 200A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EBmeter to fuse units by 19/16 PVC insulated copper wire with earth connection complete(SD-134)

Supply and fixing of 3 Phase 32A aerial fuse unit for 3 Nos 32A fuse units (500V) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron work the tapping pole with necessary clamps [SD No 135]

Supply & installation of 1.5 TR 5 star split type ac unit air-conditioner with copper coil AC Unit (carrier / voltas / O General / equivalent) Including cost of all materials at site length with necessary fitting arrangements etc complete as per std specification.(As per SOR Vol-1 P.no-208 M-1984)

Supply and laying of 5/8" and 3/8" Copper pipe (Extra beyond 3 metres supplied with AC unit) etc complete as per std specification.(As per SOR Vol-1 P.no-208 M-1990)

Supply and installation of 5 KVA capacity Automatic Voltage Stabilizer with time delay relay etc complete as per std specification (As per SOR Vol-1 P.no-208 M-1989)

Supply and fixing of MS stand for fixing outdoor unit etc complete as per std specification (As per SOR Vol-1 P.no-208 M-1991)

Supply and delivery of 10 KVA capacity 3 phase UPS (Three phase in & Single phase out) with two hours battery backup etc complete as per std specification (As per SOR Vol-1 P.no-215 M-2114)

Investigation charges for Geophysical survery finding of yeild to the point drilling of Borewell for all etc., complete

Drilling of 150mmm (6”) nominal dia vertical borewells anywhere in Tamilnadu in all formations, suitable for down the hole hammer drilling such as medium hard rock to hard rock formation, consolidated formation etc and drilling over burden to a dia not less than 200mm including insertion of 165 mm PVC casing pipe, couplings caps and other relevant materials required upto the depth as directed by the Engineer or his representative including grouting of cement 25kg (minimum) up to the depth of over burden are including borewell development flushing of borewell at a pressure 7kg/cm2 (100 lb per square inch) including yield test, crew charges, cost of consumables, transportation charges of casing pipes and all other materials including assembling complete to the satisfaction of the Engineer and as stipulated in the technical specification. The entire works should be carried out as per IS 2800 Part I & II / 1979. Finished dia of borewells shall not be less than 145mm

up to 150 mtr

from 151to 180

from 181to 200

Supplying and fixing of 150mm dia PVC causing Pipe including cost and conveyance of all materials to site and labour charges etc., completed.(As per SOR Vol-II P.no-6 WD-M0028)

Supply and Delivery of 3 Phase wet type 7.50 H.P Submersible Motor 50 LPM x 200 m head Suitable for 150 mm dia borewell confirmed to the IS 8034 Specification MER 10/25 time to the Suitable for intalation of 6" Borewell as per ISI Standred Specification (As per SOR Vol-II P.no-103 WD-M1621)

Supply and Delivery of 3 Core 4 Sq.mmCopper Cable approuved quality and design by Departmental officers including loading, unloading ,Cost and conveyance of all materials to Site for all etc., Complete.(As per SOR Vol-II P.no-124 WD-M1975)

Labour Charges for the erection of Submersible pumpset in borewell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, and erection of panel board consisting of TPICN swtiches starter voltmetre, Ammeter, three point (indicating) lamps capacitor single phasing preventor and laying and jointing the cable and twin earthing for etc., Complete and testing the pumpset and trail run for 10 days.(As per SOR Vol-II P.no-204 WD-W0872)

Manufacturing, supplying and fixing of 75mm thick Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

Refilling with excavated earth other than crushed stone sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) (SD-144)

Supply and delivery of 100lpm x 40m head Open well Submersible pump set conforming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation.(As per SOR Vol-II P.no-107 WD-M1711)

Labour Charges for erection of 7.50 HP Horizontal shaft,centrifugal pumpset (Coupled/Monoblock) in borewell/Open well including fixing of suction pipe and footvalve upto a maximum depth of 7 metres and deliverypipes to the required length with valves, pressuregauges upto the exterior wall of pump room and erectionof panel board consisting of TPIC switches starter, Voltmeter, Ammeter, Capacitor single phasing preventorand laying and jointing the cables and twin earthing asper IE rules including providing bed blocks etc., complete and operating the pumps and trial run for 10 daysincluding signing of completion of reports as required byEB authorities.(As per SOR Vol-II P.no-203 WD-W0856)

Supply, Delivery and laying of 3 Core 2.50 Sq.mmCopper Cable approuved quality and design by Departmental officers including loading, unloading ,Cost and conveyance of all materials to Site for all etc., Complete.(As per SOR Vol-II P.no-124 WD-M1974)

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 63mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with M.sand cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, M.sand cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Supplying and fixing colour galvalume sheet roof of 0.47mm thickand steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supplying and delivery of hard disk for NVR -HIGHER END 8TB including cost and conveyance of all material and labour charges etc complete PWD SOR V-1page no:224 s/no:38 M-2223

Supplying and delivery ofrack with accessories HIGHER END 2u rack including cost and conveyance of all material and labour charges etc complete PWD SOR V-1page no:224 s /no:38 M-2224

Supplying and delivery ofrack with accessories HIGHER END 6u rack including cost and conveyance of all material and labour charges etc complete PWD SOR V-1page no:224 s /no:38 M-2226

Supplying and delivery of network switch accessories cables CAT 6A UTA unarmoured cable including cost and conveyance of all material and labour charges etc complete PWD SOR V-1page no:255 s /no:11 M-2800

Supplying and delivery of POE switchess for CCTV IP CAMERA HIGHER END 8 port including cost and conveyance of all material and labour charges etc complete PWD SOR V-1page no:222 s /no:33 M-2193

Supplying and delivery of POE switchess for CCTV IP CAMERA HIGHER END 4 port including cost and conveyance of all material and labour charges etc complete PWD SOR V-1page no:222 s /no:33 M-2192

Supplying and delivery of network switchess accessories cables 16 Port Gigabit UnmanagedNetwork Switch with 2 SFP (Including Module & Pigtail) including cost and conveyance of all material and labour charges etc complete PWD SOR V-1page no:255 s /no:11 M-2796

Supplying and delivery of IP CCTV camera with poe , wdr, built in mic smp IP Bullet / dome camera with sd card support including cost and conveyance of all material and labour charges etc complete PWD SOR V-1page no:255 s /no:12 M-2807

Supplying and delivery of lan network switches HIGHER END un managed 10/100/1000 8 Port including cost and conveyance of all material and labour charges etc complete PWD SOR V-1page no:222 s /no:35 M-2199

Supply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 900 LPM at 40 metres head to develop 3.5 kg/sq.cm at the heightest and farthest hydrant point to make 30 m water jet at the time of fire fighting emergency cicumstances, coupled with 11 KW / 15 HP rated three phase 414 volts, 50 Hz, 2880 rpm electrical motor the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia., including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers (Kirloskar make KDS 1555+ or Equivalent).M-0778

Supply, Installation, Testing and Commissioning of with Butterfly valve with Body, Disc and retainer of Cast Iron Grade F.260 with EDPM rubber sleeve, Butterfly valve PN 16, SGI Hand lever operated, wafer ends conforming to BS:5155. WD-M1143,WD-M1142

Supply, Installation, Testing and Commissioning of Non return valve wafer type Dual plate,Check valve PN 16, CI body & SS plates, conforming to IS 210 Horizontal installation.WD-M1166

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.M-0828

Supply and laying of 2 core 1.5 sq.mm. armoured copper cable for control wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers. M-0786

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets,bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coatPost Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. M-0798,M-0799,M-0800

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. M-0846

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets,bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.M-0799

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers.M-0790

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers.M-0791

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges,neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers.M-0792

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary,etc., complete as per standard specification and as directed by the Departmental Officers.M-0794

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets,bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.M-0798 to M-0804

Supply, Installation, Testing and Commissioning of with Butterfly valve with Body, Disc and retainer of Cast Iron Grade F.260 with EDPM rubber sleeve, Butterfly valve PN 16, SGI Hand lever operated, wafer ends conforming to BS:5155. WD-M1142

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.M-0795

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1000mm long, 25mm dia with union / reducer,collar, clamps, etc. It shall have UL listed and FM approved.M-0840

Supplying and installing of approved type Rosette Plates (Recessed Type in Two Pieces) for sprinklers below false ceiling area. The Rosette shall be fabricated by MS plate of 2mm thick and the finish shall be powder coated and colour,as directed by the Departmental Officers.M-0841

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening,arrangement design of hanger and should confirm with specification.M-0847 to M-0850

100mm dia

80mm dia

50mm dia

40mm dia

Supply, installation, testing and commissioning of Micro Processor based conventional 4 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.M-0769

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent) M-0771

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent) M-0772

Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (Make: Apollo / Equivalent) M-0770

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers.M-0773

NOTE:- The Rate Quoted for Above Item Sl.No. 1 to 101 is Exclusive of GST 18%

Description of Work / Item(s)

Amount

Supply and delivery of Sofa set wooden material empossing and engraving antique style 6 seater L shape sofa set 1380mm length 1008mm width and 432mm height in svad fabric with central table 1 no size 432mm*432mm height and putty 20 inch including cost and conveyance of all material and labour charges etc complete(inculding GST) (as per gem rate)

Supply and delivery of Sofa set upnolstery material leatherette frame material size of 36*20 embossing and engraving 5 seater wooden material 3 seater and 2 nos of single seater including cost and conveyance of all material and labour charges etc complete(inculding GST) (as per gem rate)

Supplying and delivery of singh interiors wooden book case made up of commercial block board mr grade 5 shelves size of width 1.50m* hight -2.00m* depth-0.40m commercial block board size 38mm to 19mm bottom, 9mm taick providing 4nos of doors C.P teak wood including cost and conveyance of all material and labour charges etc complete(inculding GST) (as per gem rate)

Supplying and delivery of lab kate steel book case having three way bolting device controlled by 6 lever lock size of width 9.14m* depth 0.32m height 1.74m, thickness of M S sheet for shelt 0.80mm and top bottom back and sides 0.8mm including cost and conveyance of all material and labour charges etc complete(inculding GST)

Supplying and delivery of wooden chair length 20inch width 20inch height 33inch carving and painting for deparment office including cost and conveyance of all material and labour charges etc complete(inculding GST)

Supplying and delivery of computer table consists of computer cum printer table with key board pullout tray and table top of side computer table 10mm. 900mm*600mm*750mm size of printer table 10mm. 750mm*750mm*750mm size of key board tray 600mm (tront width) 500mm depth provided with end fitting made from 2mm thick MS steel movnted on --- side weeding with an angle size 17mm*17mm*3mm and of back on the top six and covered 2mm thick MS sheet b lever lock with set of 2keys of non ------ including cost and conveyance of all material and labour charges etc complete(inculding GST)

Supplying and delivery of excutive table with one side pede stel unit and ERU of size width 2.40m*depth 0.90m height 0.76m. 2 storase units with shetter taree drawers laminate in colour with matt finish 0.60-0.80mm thick for edge to be banded with pvc tape 2mm thick with the help of hot melt give flat single layer pre laminated MDF board contorming to having PLMDF-23 OF 14587 including cost and conveyance of all material and labour charges etc complete(inculding GST)

Supplying and delivery of toys pivs six seater table chair kit rotational moulding table top portion ovel shape main les 2nos with x joint provision taree seater bench 2nos arc shaped center support les for three seater bench 2nos in including cost and conveyance of all material and labour charges etc complete(inculding GST)

Supplying and delivery of reading table for solid wood 4 seater size of 1.83m*0.914m*0.914m table top thicknes 36mm four corner les's pendestal 25mm*50mm thick including cost and conveyance of all material and labour charges etc complete(inculding GST)

Supplying and delivery of vai dya rectangular adjacent of leg size of table length 1350mm*600mm*675mm. Table top per laminated particle board,1.60mm matt silver anodized aluminiam extrusion less assembled togeather with 8mm thick ms poweder ---- including cost and conveyance of all material and labour charges etc complete(inculding GST)

Supplying and delivery of dvnong intel core i5 12500 16GB / 1000 GB HBD windows 11 profesional computer desktop with central processing unit (CPU) and key board IPS monitor techology, SFF cabinet form LED size 23.80inches monitre resoultion (PIXELS) 1920*1080 including cost and conveyance of all material and labour charges etc complete(inculding GST)(as per gem rate)

Supplying and delivery of erection of solar roof top 18KWP special category states including Photo-Voltaic solar modules, inverters, balance of systems including cables, Switches/Circuit Breakers /Connectors/ Junction Boxes, mounting structure, earthing, Lightening arrester, cost of meters (if any other than net meter), local connectivity cost, cost of civil works, foundations etc. and its installation, commissioning, transportation, insurance, capital cost of online monitoring, comprehensive maintenance charges for five years, applicable fees and taxes etc.(adopted MNRE/2021-2022 Ministry of new renewable energy rate)

NOTE:- The Rate Quoted for Above Item Sl.No. 1 to 13 is Inclusive of GST 18%

SURA BUILDERS (BID ID -1187033)

SURA BUILDERS (BID ID -1187033)