Construction of Samaj Ghar at Saimilan Dalgaon under 45th constituency, GTA

Earthwork in excavation of foundation trenches or drains in all sorts of soils (including mixed soil but excluding laterite or sand stone) including removing spreading or stacking the spoils within a lead of 75 m as directed including trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water etc. all complete. a) Depth of excavation not exceeding 1.5 m.

Earthwork in filling in foundation trenches or plinth with good earth in layers not exceeding 150 mm including watering and ramming etc. layer by layer complete. B) With earth obtained by fresh excavation upto 1.80m depth. From land arranged by the Deptt. within a lead of 100m.

Labour for laying 150mm to 200mm boulder soling including rough dressing hand packing and ramming down small pieces without rolling and preparing the bed to proper level and filling up all joints with sandy clay or earth.

Supplying and of stone boulders

Cement Concrete with graded stone ballast (30 mm size) excluding shutteirng. (B) In ground floor (with N.B. Variety Stone metal) (a) (1:3:6) proporaton

Plum concrete work with 40% Cement concrete and 60% boulder filling.

Ordinary cement concrete (mix 1:2:4) with graded stone chips (20mm nominal size) excluding shuttering and reinforcement, if any in ground floor as per relevent IS codes. (a) River bajree

Reinforcement for reinforced concrete work in all sorts of structures including distribution of bar, stirups,binders etc. initial straightening and removing of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection complete as per drawing and direction. (a) For works in foundation, basement and upto roof of ground floor/ upto 4m

Hire and Labour charges for shuttering with centreing and necessary staging upto 4 m. using approved stoutprops and thick hard wood planks of approved thickness with required bracing for concrete slab, beams and columns,lintels curved or straight including fitting & fixing and striking out after completion of works (upto roof of ground floor) a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-in-Charge

125 mm thick brick work with 1st class brick's in Cement mortar (4:1) in ground floor.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar, including rounding off corners or chamfering corners as directed and recking out joints or roughening of concrete surface. with (4:1) cement morter 20 mm thick plaster

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar, including rounding off corners or chamfering corners as directed and recking out joints or roughening of concrete surface. with (4:1) cement morterwith (4:1) cement morter 15 mm thick plaster

Neat Cement unning about 1.5mm thick in walls dado, windows sills, floor drain etc. NOTE Cement 0.152cu.m /100sqm.

Artificial stone in floor, dado, staircase etc with cement concrete 1:2:4 with stone chips, laid in panels as directed with topping made of ordinary or white cement and marble dust in proportion 1:2 including smooth finishing and round off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. 3mm thk Topping (Using Grey Cement) 20mm thk.

Wood work in door & window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, iron butt hinges and M.S. Clamps ( The quantum should be corrected upto three decimals.

Supplying , fitting and fixing M.S.Clamps for door & window frame made of flat bend bar, end bifurcated with necessary screws etc. by cement concrete 1:2:4 as per direction.

40 mm x 6 mm, 200 mm length

Panel shutter of door and window, as per design (each panel consisting of single plank without joint ), including fitting & fixing the same in position but excluding the cost of hinges and other fittings. 40 mm thick shutters with 19 mm thick panel of size 30 to 45 cm. Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallk.

Supplyingbest Indian sheet glass panes set in putty(as per IS specification) and fitted and fixed with teak beads and nails complete. (In floors for internal walls & upto 6m Height for external wall)

Iron butt hinges of approved quality fitted and fixed with steel screws with iSI mark.100 x 58 x 1.90 mm

Iron catch hook of approved quality fitted and fixed to shutter and chowkat. 12 mm dia X 750mm long

Anadoised aluminium barrel/tower/socket bolt (fully covored) of approved manufactured from extruded section confirming to IS 204/74 fitted and fixed with cadium plated screw. (viii) 225mm long x 12mm dia bolt.

200 mm long x 10 mm dia. Bolt

Anodised aluminium Aldrop/ Sliding bolt of approved manufactured from extruded section conforming to I.S. 2681/66 fitted and fixed complete. 250 mm 16 mm dia. bolt

Anodised aluminium 'D' type handle of approved manufactured from extruded section conforming to I.S. 230/72 fitted and fixed complete. ii) 100mm gripx 10mmdia rod.

150 mm grip x 12 mm dia. Rod

Priming one coat to timber or plastered surface, with ready mixed primer of approved quality, including smoothening surface by sand papering etc.

Priming one coat to steel or metal surface, with ready mixed primer of approved quality, including smoothening surface by sand papering etc.

Applying Decorative cement base paint of approved quality after scraping the surface throughly as necessary on plastered, ruled or concreted surface (Manufacturers' specification to be followed). iii) Two coats. (Outside)

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per Manufacturers' specification) including cleaning and smoothening of surface.

Painting best quality synthetic enamel paint of approved make and brand including smoothering surface by sand papering etc. including using of approved putty etc. on the surface, if nescessary a) On timber or plastered surface.

(b) Steel or other metal surface

Please Enable Macros to View BoQ information