PROVN FOR SIT OUT BALCONY AT BLDG NO. P-51, COVERING SIT OUT BALCONIES OF BLDG NO. P-147/1, P-148/2 AND 148/3 OFFRS MD ACCN AND KITCHEN WORK (02 X WOODEN CABINET AND 01 X CHIMNEY IN BLDG NO. P-16 AT DALHOUSIE CANTT.

S&F 0.5 mm thick pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and directed.

M & L for Steel work in tubular trusses and frame work including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240,6mm angle used as in steel complete all as specified and directed.

Excavating in post holes in any type of soil n. exc. 0.50 cum getting out returning filling in and ramming earth or brocken rubble mixed with earth around, in layers not exceeding 25 cm watering, and removing surplus soil to a distance n. exc. 50 m and making good surface, complete all as specified and directed.

Plain cement concrete 1:2:4 type B-2 using 40 mm graded stone aggregate as in mass concrete or mass concretre complete, all as specified .

M&L for preparation of steel and iron surfaces of any description, not otherwise described, over 10cm width or girth with two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, complete all as specified and directed.

M& L steel iron base plate plugs, bolts, and screws of Fe 410-W(Gde-E-250 Quality -A) complete all as specified and directed.

S&F angles as in posts and struts in fencing including cutting top to shape as direct, drilling holes, notiching for wire etc, flat iron fillet (for securing wire mash etc) incl all necessary drilling bolting or reveting,etc and similar work conforming to Fe410-0 or Fe-310-0.

M & L for PCC 1:4:8 (Nominal mix) using 40mm graded aggregate as in foundation mass concrete all as specified.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F sheet glass, 5.5 mm thick ordinary quality and glazing with glazing pin in square exc 0.5 sq. m in each pane for aluminium door windows, complete all as specified and directed.

S&F in factory made 17-18mm thick WPC (wood plastic composit boards) sheet one side prelam sheet and other side wood nature colour for cupboard shutter of density 600 kg/cum with 100% termite/water proof, fire rertradent, Eco friendly and finish at all edges at level for making edges lipping using binding tape etc as in Kitchen cupboard,Cabinet etc complete all as specified /Manufacturer's specification and directed

All as per Srl item No 11 but both side plain board complete all as specified and directed.

S& F 150 mm size stainless steel brignt finish handle as approved by GE, fixed with Nut and bolt complete all as specified.

S&F Telescopic type Side channel of drawer of standard size incl roller for moving drawer made out of mild steel bright finish or electro galvanised ( soft close ball bearing runners) with width of flap 30mm & 60mm long, ISI marked complete all as specified.

S&F stainless steel plain basket of size 17''x20''x6'' and weight not less than 1.4 Kg, ISI marked complete all as specified and directed.

S&F Stainless steel partition basket of size 17''x20''x6'' and weight not less than 1.4 Kg, ISI marked complete all as specified and directed.

S&F Stainless steel cutlery tray basket of size 17''x20''x6'' and weight not less than 1.4 Kg, ISI marked complete all as specified and directed.

S&F Stainless steel cup & soucer of size 17''x20''x4'' and weight not less than 1.4 Kg, ISI marked complete all as specified and directed.

S&F Stainless steel plate basket of size 17''x20''x6'' and weight not less than 1.6 Kg, ISI marked complete all as specified and directed.

S&F Stainless steel auto, zero crank hinges,fancy type with concealed pattern fitted to shutters, ISI marked complete all as specified.

S&F Magnetic catcher for shutter of approved pattern fitted with suitable screws complete all as specified and directed.

Taking down cement plaster on brick walls or stone walls of any description etc including raking out joints, hacking for key, scrubbing down with water etc, rubbish off the premises complete all as specified and directed.

M&L for Rendering 10mm thick on fair faces of brick work, concrete sruface in cement mortar (1:6), finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 in two layers (10+5mm) on brick masonary of brick work surfaces finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered surface of wall and appying two coat of cement base paint mixed with silicon based water repellent compound over a coat of primer by roller/brush complete all as specified & as directed by Engineer-in-Charge.

M&L for preparation of new plastered surface of walls and applying two coats of oil bound distemper over a coat of chalk whiting complete all as specified and directed.

M&L for 17-18mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including demolition of old stones/tiles complete all as specified and directed.

S&F kitchen sinks with drainage board made of stainless steel 1mm thick with plugs, washers , PVC waste pipe fixed in repair including waste copling; bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915x460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for reinforcement cut as required to facilitate demolition, complete all as specified and directed

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified & directed.

S&F Mild steel TMT bars bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified & directed.

M&L for reinforced cement concrete 1:2:4 type B-0 (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns, in floors, roofs, landings, balconies,facia, canopies, deck slabs and in shelves including necessary formwork and the like complete all as specified.

Supply and intallation, testing and commission stainless steel wall mounting touch/ push button, multiple speed electric chimney with hood width not less than 90cm, with heavy duty noise free copper wound 250W electric motor suction power 1000-1200 cum/hr filterless autoclean with SS/Aluminium duct of size not less than 150mm of required length as per site all as specified and directed by Engr -in-Charge of Make - Glen 90cm/Faber Primus Plus/Hindware/Kutchina Virgose DLX. Note- The installation shall be done by the OEM rep and the rates includes the ducting pipe, installation/ mounting charges including making holes or wall drilling in any type of masonary.

Material and Labour for Wiring for circuit/submain wiring alongwith earth wire with FRLS PVC insulated copper conductor of size 2x4.0 sq. mm + 1x4.0 sqmm earth wire single core cable run through and including PVC rigid concealed conduit of size 20mm all as directed by Engr-in-Charge. Note - Rates deemded to be included for cutting chases in any type of masonary.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed.

Supply and fix modular 2 in 1, 3/5 pin switch socket combination 16 Amp, four module with concealed modular GI sunkun box with cover plate all as specified and directed.

S&F MCB single pole 25Amp 240V in existing MCB DB all as specifed and directed.