LIFT IN POLLUTION CONTROL BOARD VELLORE

Amount

Design, Engineering, Supply, Fabrication, Erection, Testing, commissioning and handing over of 1 no 10 persons capacity Gearless Without machine room passenger lift as per the following specifications including taxes and duties. (Make : KONE/Equivalent) 1.Location: (Pollution Control Board office), 2.No of lift: one no, 3.Type of lift: passenger (Machine Room Less model), 4.Capacity of lift: 10 persons / 680 Kgs, 5.Speed: 1mtr / sec, 6.Type of drive: V3F drive with enhanced ride comfort and near zero level functions, 7.No of floors: GF+2Floor, 8.Total travel: 3 .3+3.3 =9.9Mts, 9.Leveling accuracy: high level accuracy with smooth and jerk free stopping, 10. Construction of CAR: midrange Basic SL 10 Btushed stainless Round Bend Handrail silver brushed stainless steel (ST4) at rear wall and Perspex false ceiling, 11. Position of machine: directly above the lift well, 12. No of landing service: Front side-2 No’s and Right Side - 1 No's, 13. No. of car entrance: one in the front side and one in right side, 14. Car entrance door: power operated automatic V3F drive center opening sliding SS door, 15. Landing entrance door: power operated V3F drive center opening sliding SS door with provision for emergency exit key at all landings, 16.Size of Lift Well 2300 X 2300 X (MM Wide*MM Depth), 17.Lift pit:1800 mm, 18. Lift Car Inside Size 1350 X 1300 X (MM Wide * MM Depth ), 19. Clear opening of Gates / Doors / Lintel : 800 X 2200 (MM Wide * MM Height) Lintel - 2100 mm, 20.Lift machine room size: Nil, 21.Power supply: AC 3 PHASE, 50 CYCLES, 415 VOLTS ±10%, 22.Control: micro computer (micro processor):based simplex collective control with / without attendant, 23. Car fittings: LED lighting with 1 no 300 mm sweep cabin fan,

24.Lift well: RCC construction with brick masonry to be constructed by PWD civil wing, 25.Induction: UP / DOWN digital direction and position indicator for all landings and inside the car, 26.Emergency alarm bell: battery operated bell to be provided with automatic charging device, 27.Emergency light: battery operated light to be provided with automatic charging device, 28.Fire mans switch: to be provided at the GF, 29.Minor builder works: to be provided by the lift contractor, 30.Scaffoldings: to be provided by the lift contractor, 31.Sill angles and facia plates: SS to be provided by the lift contractor. 32.Steel for lift machinery: to be provided by the lift contractor. 33.Servicing and maintenance: free comprehensive servicing and maintenance for one year Guarantee period to be provided by the lift contractor, 34.Automatic rescue device: to facilitate the landing of the nearest floor at the time of power failure this shall consist of suitable battery system with charger inverter under voltage protection system etc. complete with all accessories, 35. Provision for intercom with phone: to be provided by the lift contractor., 36.Lift license: preparation of drawings payment of charges to CEIG and insurance policy if any and obtaining CEIG approval for the lift as per lift act should be done by the lift contractor, 37.Floor position announcer: to be provided by the lift contractor, 38.Special features a) Infra red door sensor with full height screenb) Full width half height rear panel mirrorc)Tubular SS hand rail in car d) Stainless steel signal features e) Vandal proof SS button with SS coverf) SS door frames for landing doors g) V3F door operator h) Call register signal i) Stainless steel facia plates for car operating panel and landing fixtures j) Steel ladder for lift machine room,

k) On / off switch for fan and light l) Over load warning indicator with audio announcerm)Voltage stabilizer for control circuits n)Braille button, 39.Over speed governor phase failure and phase reversal relay alarm bell T guide brackets for car and counter weight rubber padding under the winding unit motor of adequate capacity signal reduction worm gear electromagnetic brake with compression springs car safety gears buffers electro mechanical locks emergency key side supporting angles motor over load protection devices final limit switch main suspension ropes counter weight lifting joist for mounting the machineries 40.Guarantee: guarantee at least for one year for the material and workman ship of equipments should be offered by the lift contractor. 41.Site testing in accordance with IS 14665 should be carried out at the time of handing over to the user department, 42.Supply operation and maintenance manual and necessary tools for operation and a set of Spare parts required for one year. ( Make: KONE/Equivalent)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only

Supply and fixing of Four Pole Metal enclosure DB with 1no 63A FPMCB on wall with connections

Supply and run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall and ceiling for earth connection

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

SURESHBABU (BID ID -1325818)

GUNASEKARAN (BID ID -1326074)